MANUEL UTILISATION · USER MANUAL · MANUAL DEL USUARIO
Contents
1. E Satellite Select the desired satellite option only avail able in GPSK cards E Search type Select FTA channels or all FTA Coded E Search net Select NO for searching all channels and YES to find new channels only on the current net work option only in GPSK cards When concluding the adjustments of this menu you will be able to press EXIT to leave the menu or OK to search for the channels of the current satellite The process may take few minutes User Installation Manual search This menu configures the manual search of the channels in the chosen transponder Parameters to be adjusted for QPSK cards 3 bri ta ali ri Manual Search Sais Search b ali Exit Guh Satellite Select the desired satellite Position The longitude of the satellite is given Transponder You will be able to choose a trans ponder of those memorized on the list The trans ponder can also be edited Frequency It can be edited Rate The symbol rate can also be edited Polarity Horizontal Vertical Left Right Search Free to air or all FTA coded Look for PID to edit the PID of video audio tele text and or PCR then choose YES and press OK When concluding the adjustments of this menu you will be able to press EXIT to leave the menu or press OK to search for the channels of the transponder Please wait until the operation ends Parameters to be2. FicaB or by means of the frontal buttons Fiesa The program mer has its own display Programmation by means of remote control or frontal buttons needs a tv set with its AV input connected to the RCA video out put connector of the receiver we want to program FIG3B Then Receiver Selection If you use the programmer FIG4A connect it to the RS232 of the required receiver and press the ESC key READY or the first parameter to be adjusted will appear on the programmer screen If you don t use the programmer please press the frontal M button Fic3A and see the tv set menu Inputs parameters For OFDM receivers press the IN key Program mer MENU Remote control or M frontal buttons and by means of the 4 keys select select the input RF standard B G I D BB To select the other input parameters press successively the IN Wkev With 4 4 keys select the input chan nel e5 e69 the bandwidth 6 7 8 MHz Auto the transmission mode 2K 8K Auto the modulation system Auto the guard interval Auto 1 32 1 16 1 8 1 4 and the SFN algorithm NO for static re ception NOTE Is convenient to select AUTO in the maximum number of fields that you can The following menus will appear in the programmer and in tv set OSD Remote control TV Set OSD Standard nput Mend f Standard Channel Video Channel Audio Bandwith Auto Output Mode Tes Info Modulation Modul Guard Interva
3. Remote control Band RF Channel Audio subcarr Remote mode USER NOTE If this screen doesn t appear then press suc cessively the front key M EE By means of the keys lt gt Programmer Remote control or the keys push buttons choose the desired output channel mA order to select the other parameters of the HEADEND INSTALLATION screen press succes sively the key w With the keys 4 select the audio subcarrier 4 5 5 5 6 6 5 the LINK mode of remote programming Hotel or User accord ing to paragraph F the desired video norm PAL SECAM the RF standard BG BGltalia L DK BB and the frequency band E S Now press OK to save the changes and go out of the current screen by pressing the key ESC programmer EXIT remote control or M push buttons It will ap pear the message PLEASE WAIT Next by means of the keys aw 4 go to the system configura tion languaje option press OK and with the arrows 4 choose the desired language Press OK and then press again ESC EXIT or M It will appear in the programmer or in the TV screen the following screen Remote control Television Info on TV IHEADEND INSTALLATION User Installation System Configuration Channel Organizing Program Guide Games If you desire to go out from the programming mode red led is blinking every 0 5 sec press again ESC EXIT or M The system will also automatically go out of the program
4. THE POSITION OK If you want to store a new position obtained with Moving antenna then select with the keys lt gt the option KEEP POSITION and press OK Any way it is preferable to do a fine alignment of the antenna position To return to the default fac tory memorization press the red key Reset of the motor With the green key the signal will automatically be optimized Move antenna By means of the keys 4 you will be able to move the antenna West East Se lect with the blue key the movement type step by step or continuous mode When concluding the adjustments of this menu you wil be able to press OK to look for the channels available in the satellite Automatic search menu or EXIT to leave the adjustments In the first case you will be able to choose which type of channels are to be displayed all only the free to air or only those belonging to a certain network During all the process two level bars are dis played to inform about the power and signal level User inst DiSEqC 1 2 Positionner Config menu Available only in the QPSK satellite cards Atten tion You can use only one polar antenna per each DigiCompact8 see fig 16 J2 ihar Fatale s Praonar Corian See or GOTO Ok Se Es i Sai Antenna type Select this option in case of appli cations with antennas and motor DiSEqC1 2 If the motor is GOTOX type then go to the previ
5. TNT VDI SAT MPEG 2 4 3 16 9 MPEG 1 layer I II 32 44 48 96 KHz Stereo mono LCD 8 charact 2 lines 27 RS232 Connections amp signals RF inp loop through RF out loop through Program interface Interm red led 1s Interm red led 0 5s Green led Stream bus VDI TNT VDI SAT VSB Mono 120 860 MHz PAL BG DK BB SECAM L 4 5 5 5 6 6 5 lt 1 dB 85 0 20 dBuV gt 60 dB for OUT Level lt 80 dBuV IEC F connectors 2 F fem connectors 2 DIN DB 9 uP Supplied Programmation mode Tuned to one channel 8 bits parallel G LINK SYSTEM DIGITAL V8 station comes from the factory preset to the SMATV system that is say that programma tion must be done directly on the station There ex ists another possibility which is the remote program ming by means of the LINK SYSTEM with 2 different subsystems VDI LINK All the cards are controlled from one sin gle point i e from the hotel reception See fig 16 NN VDI USER LINK Each user cont is its own card i e in one collective building or in a small hotel See fig 15 In the TV outlet from we want to control the head end there should install a VDI LINK equipment cod MS1699 For the HOTEL MODE the switch should be situated 0111111 For the USER MODE the switch should be situated according to the Fic17 depending of the RF channel assigned to each user See paragraph
6. displayed is being sent by the own channels You will be able to perform the following E Select the general list favourite list FAV key E Order alphabetically by number yellow key E Select a channel 4 w keys or letters E Select time table 4 keys Note You can access to this menu with the keys MENU 4 OK and also directly with the EPG key Ell GAMES MENU In this menu there are available three different games TETRIS FROGGER and SOKOBAN EXIT FROM THE INSTALLATION MENU To leave the installation menu press successively the ESC key At the end an informative BANNER of the tuned channel will appear and after the time of ac tive menu adjusted in the section K3 it will disap pear If you want to enter again in Installation menu then go to the section CHANNEL SELECTION If you are not in the Programmation Installa tion Menu then focus the remote control to the sensor of the VDI LINK and press the MENU key If the head end is in HOTEL mode then a code will be displayed on the screen for example 7921 Television 7921 Introduce in the remote control this code the figures will be highlighted once you press the remote control Television HEADEND INSTALLATION User Installation System Configuration Channel Organizing Program Guide Games keys Repeat some key if he doesn t remain high lighted Next it will appear the following screen Note In USER mo
7. screen not those of installation Please remember that after this time any information enquiry will require to en ter a code in the remote control if it is in Hotel mode Time Area Select the time area of your country For example GMT 1 for Europe western winter E Starting Channel Option available according to the software version TV Adjustment System corliquration adjmimenis The parameters on this screen can not be modified from the system LINK Only can be configured di rectly from the headend menu HEADEND INSTAL LATION following the instructions in section H 3 Timer This menu allows to switch on to switch off and to change the channel in a temporized way Follow the instructions of the receiver menu System configuration gt Timar pilari irnir OK Save Paternal block This option allows to block the menus installation configuration favourite channels Games to block the channels and to change the PIN code By means of the 4 and OK keys choose the desired options The first code by default is 0000 Note the new one in a secure place Menu s Lock option allows to the modulator in Hotel Link Mode to lock all menus except channels and favorites menus This option is very useful for Hotels to allow them to change channels on favourites lists without changing any system configuration Bloqueo de los menus Lista de mends Canales fav
8. the receiver which we want to configure to the AV input of one TV The following process should be done for all the re ceiver cards of the head end It is indispensable to adjust the modulator of each card to one different channel example card 1 to channel 23 of UHF card 2 to channel 5 of VHF etc if you have programmer FIGAA connect it to the input connector RS232 from the receiver to be programmed If you don t have this programmer use the IR remote control or the frontal push buttons to perform the following instructions Press and maintain pressed the frontal key OK while the general power supply is momentarily in terrupted Fic amp A or while the Reset button is pressed FiG3B 3c The OK key should be maintained pressed until it appears the following menu in the program mer display or on the television screen Remote control Television Select initial FIRMWARE LINK M 86XX X XX SMATV X XX Active firmware Press OK to select Press ESC to abort By means of the keys aw choose the LINK option and press OK The receiver will automatically be re started Note Any receiver configured to the LINK system can be return back to the SMATV system repeating the section 3 for this option Wait until it appears the initial menu in the TV screen If there is no signal then it will appear the following screen Television HEADEND INSTALLATION Mode PAL TV System B G E 5 5MHz
9. H5 and FI6 15 NOTE Position 1 2 ON IE REMOTE CONTROL Fig 4b The remote programming within the LINK system is carried out exclusively with the remote control The available buttons are the following TV Radio mode change between TV channels and Radio channels amp Selection of channel number and introduction of the menu option number 8 Mode teletext and it s options 4 Mode subtitles 6 8 Move the cursor up down Change the channels when one channel is being seen 8 Press to display the Main Menu in the screen Show the channel list Execute the selected op tion in the menu screen or introduce the value in any input mode Move the cursor to left right Move up down one page in the channel list Adjust the volume when one channel is being seen Pressing successively displays the channel and program information In the USER MODE starts or leaves in stand by the receiver In the HOTEL MODE re starts the receiver 3 Show the favourite channel lists 3 Return to the last tuned channel Start the EPG Electronic program guide B Change the audio languages when you are seeing a channel Change between audio left right stereo Come back to the previous menu or go out from the options Press to switch off the sound temporally Press again to return the sound back 69 Pause Volume EE CONFIGURATION OF THE CARDS WITH THE LINK SYSTEM Connect the video output of
10. MANUEL UTILISATION USER MANUAL MANUAL DEL USUARIO DIGITAL Vs STATION DE TRAITEMENT NUMERIQUE DIGITAL HEADEND SS M SOMMAIRE A INTRODUCTION B MODELES C MONTAGE DES MODULES D RACCORDEMENTS ET INSTALLATION E PROGRAMMATION F CARACT RISTIQUES TECHNIQUES USER MANUAL INTRODUCTION DIGITAL V8 is a Compact Receiver Station for satel lite amp terrestrial digital tv It can be configured at the customer s choice The product integrates 8 com pletely independent receiver modulator modules launch amplifier power supply programmer DIGITAL V8 offers the flexibility to mix cards for Satellite reception PSK PAL and Digital Terrestrial reception OFDM PAL with the individual choice for each module to have built in a wideband mono stereo modulator DSB or VSB type for applications with adjacent channels By means of low losses RF bridges the output of each module can be mixed and redirected to a launch amplifier with high output level in order to have a distribution of all the system channels through one single cable which makes it compatible with old and new buildings owing to the small space required As well this system allows existing antenna mixing and cascading with several stations to reach the desired number of channels in every network DIGITAL V8 incorporates several set up methods by means of friendly OSD menus which can be selected from the front switches available in each c
11. O Commutation 0 12V only if it has this specific switch Select the value corresponding to the in put of the switch E LNB Select ON or OFF depending if you want to feed the LNB from the receiver Attention Only one receiver can feed every LNB At the end press OK to store the changes or EXIT to leave the menu User inst GOTOX Positionner Configuration Menu Available only on the satellite GPSK cards It allows configuring an antenna motor for the reception of several satellites Attention You can use only one polar antenna per each DigiCom pact8 see fig 16 J2 Eze e vel Select ce BOTS ert earls Parameters to be adjusted for motor GOTOX Antenna type For antennas with motor GOTOX select this option If the motor is DISEqC1 2 then go to the following section Region City Select the area and city that cor responds to the reception position Automatically it will be informed of the longitude and latitude Adjust to this latitude the elevation of the motor regarding the mast Satellite Select the desired satellite Transponder Select the desired transponder for the orientation of the antenna and signal level among all those available on the memorized list If you want to add or to remove transponders then go to the Installation Manual search menu Position When needed that the motor rotates to the position of the selected satellite press OK in the option to GO TO
12. R RIT SS FIG 17 b USER CODE FOR UHF OUTPUT CHANNELS
13. adjusted for OFDM cards Live Paton daal Seach TV System Select the channel plan system V UHF of your country B G I L etc E RF Channel Select the channel V UHF that wants to be searched Frequency Select the frequency value E Search Free to air or all FTA coded Look for PID If you want to edit the PID of video audio teletext and or PCR then choose YES and press OK User inst Factory default values With this menu you can return to the initial situation of production of the receiver It will request if you want to maintain the current language Press OK to continue or EXIT to quit SYSTEM CONFIGURATION MENU System Configuration This menu offers the following options Sig m Ere gt Lee trina Lu cgurgr tala eh TR reed ganET Choose the desired submenu by means of the aw and OK keys Languages This menu offers the following options Systarm cznliguratinn d O50 Language i E EN CHIETI Choose the language for each option by means of the 4 and OK keys Press OK to store the changes or EXIT to quit User Selec arezreuna Da zal gau Emir Ok Save chan Parameters to be adjusted E Screen Colour Transparency level Select the colour and transparency level from the menu options as you wish Time of active menu It s the time that the menus will remain in
14. ard from a IR remote control or from a RS232 programmer with display Also it can be remotely programmed from any TV set located at any point of the distri bution so that the operator whether a community building hotel or hospital can easily access and control the station parameters Even it can be pro grammed by GSM system VDI GSM All modules are mounted in a robust aluminium com pact station of reduced dimensions which could be mounted on a rack or wall support with simplicity of assembly and upgrade with fan system useful for any temperature environment and protected with key against the access of unauthorized personnel IE MODELS AND ACCESSORIES VDI BOX Compact station P Supply Re Control fans VDI SAT QPSK Module VSB VU Mono Modulator VDI TNT COFDM Module VSB VU Mono Modulator VDI LINK Station remote control accessoire VDI MOD VSB VU stereo modulator VDI PROG 5232 Programmer VDI ZAP Infrared remote control VDI PCMCIA PCMCIA card reader VDI CARD Multicrypt card reader VDI GSM Station programmation system for GSM VDI 19 19 rack adapter MOUNTING THE MODULES For installation of the GPSK OFDM modules first open the general DIGITAL V8 cover see Fic Slip the re ceiver modules in the plastic guide Fiesa and fix them by means of screws to the upper bar and the lower base FIG5B C FIG3A B C shows the connectors for the input and output RF video audio L R as well as those for p
15. de this screen will directly appear when pressing the MENU key from the remote con trol in front of the adjusted VDI LINK according to table 17 If you don t want to program the receiver module then press the ESC key An informative BANNER of the tuned channel will appear during the adjusted time in the section K3 GEJ To select the general list or the favourite lists press successively the FAV key until the desired list appears in the screen Note In the general list disappears the indication FAV To select the channel you can perform any of the following options a Press the aw keys successively b Press directly the channel n C Press OK the chosen list will appear Next you will be able to se lect the channel by means of the 4 w keys or the nu meric keys To select the channel press OK Note In the option c you can change the list by pressing FAV key to order alphabetically or by numbers by pressing the yellow key and to add the channel to a favourite list by pressing the blue key and proceeding as indicated on the section L To leave the menu press EXIT or OK To select RADIO channels press the key TV RADIO and act like indi cated for the video channels To make disappear the banner press the ESC key IE CHANNEL INFORMATION At any time that a channel is visualized you can request the channel guide Follow the section P1 and press the INFO key It will appear the corresponding informatio
16. e receiver to be programmed Now focus the remote control to the sensor of the VDI LINK and press the key MENU If you are in USER mode it will appear the next screen Television HEADEND INSTALLATION User Installation System Configuration Channel Organizing Program Guide Games If you were in HOTEL mode you should select the desired receiver To do it it will appear a code in the screen for example 7921 Television Pin code 7921 Press this code in the remote control the figures will be signalised when you press the keys Next it will be displayed the screen previously indicated Instal lation Configuration By means of the remote control keys focused to the sensor of the VDI LINK you will be able to access to the menus of the following section and to configure and to tune the channel of each receiver USER INSTALLATION MENUS To display the menu lists press the keys gt Aw and to confirm it presses the OK key It can also be used the numeric keys in the remote control to directly introduce a numeric value to see the TV Use the keys 4 to move to the left or the right from a line to the other Use the keys w or A to move the cursor up and down in the submenu To leave the menu system in any time press the EXIT key in the remote control Next we present the different available menus for each option of the previous fig If you have a OFDM receiver go to step J4 User installation LNB Config
17. ges have been saved Press ESC to exit without saving the changes z NOTES It is not possible to memorise channel parameters if the receiver doesn t receive signal If the input signal disappears or the tuning lock is not correct the receiver will be on stand by with auto matic retuning system every 20seg Prog control will show WaitXM If you want to re start yourself the unit disconnect for a while the power supply Press ESC at any time to exit or OK to save the chang es they will automatically be saved after 10 minutes For QUATTRO LNBs recommended adjust the polar ity in QUATTRO position 18Vdc See step E2 B of the programming instructions Pressing the TEST key will appear the soft version and the information of the following figures TV Set OSD TV Set OSD Input Men AGC STR Video TPSignal Descra Audio Constell Input Men Video Audio Output Hier Mode Output Tes Info FEC BER SNR Tes Info Freq offset 4KHz If you want to update the GPSK OFDM receiver soft from another unit press IN and R5 on the master unit programmer It will appear the next figure Interconnect unitsbvRS232 Disconnectand connectpowersupply on the client unit TV Set OSD Connect a Null Modem cable between the units Disconnect power on the other unit and reconnect power Transmission will start automatically 2 24 Transmitted 096 If a softwa
18. ion of the VDI LINK mounted in the head end again refer to section I2 4 IMPORTANT NOTE For systems of remote pro gramming it is indispensable that all the cards are programmed to different output RF channels sec tion H5 SAT TILT CONTROL DCIN RF GAIN TA FIG 2 AMPLIFIER GENERAL VIEW MS8613 23 S IR sensor a RS232 for LED s external program OL OL Ol TOL TOL FIG 9a OUTPUT MIX AND AMPLIFICATION 3 3 L O uL __ E FIG 9b EXT ANT MIX Qooo ose Bo 8 m c Program Buttons E DTT Antenna SAT Antenna LNB Quatro IR sensor LED s Program Buttons RS232 for external program Existing Distribution Installation Video out Out RF Bypass out FIG 3b QPSK GENERAL VIEW Bypass ant in Stream out IR sensor LED s FIG 111 VDI LINK TEST Program Buttons RS232 forl external program DCin RF Level FIG 3c OFDM GENERAL VIEW FIG 7 QPSK REC amp IF AMPLIFIERS INPUTS DTT Antenna SAT Antenna LNB Quatro Amplifier Existing Installation optional Distribution FIG 13 WIDE BAND AMPLIFICATION LNB Quatro 1 USER Link Code QOOO0000 VDI LINK FIG 15 USER MODE Channels Switches ON Channels Switches ON Option polar mount antenna e e p 1 1 i DiSEqC L HOTEL LINK CODE 00000000 Switches ON 2345678 FIG 16 HOTEL MODE Channels Switches ON Cha
19. ion will also be tuned to every specific channel The figures 13 14 and 15 indicate different examples of configu rations To tune the channels from the VDI LINK located in the user s outlet follow the steps carried out in head end section P and Q The only difference is that now it won t be necessary to enter any code since the own VDI LINK adjusted according to table 17 directly establishes the corresponding code 2 The same as in HOTEL mode but now with the USER mode you will be able to modify most of the configurations of the receiver section J to Q TECHNICAL NOTES HOTEL or USER MODE If the receiver doesn t respond to the MENU key from the remote control 1 Please verify the codification of every VDI LINK make sure it corresponds with the table 17 user mode or fig 16 Hotel mode 2 Please verify the distribution network Remember that all orders coming from the remote control are transmitted in reverse sense to the 11MHz signal Therefore the reverse attenuation of the network to this frequency should not be bigger at 359GB If in some point of the distribution there is a re am plifier use two MV7306 to make a bypass of the 11MHz signal Equally if it S used an amplifier in the head end different to the MS8641 8640 it will be necessary to mount a MV7306 as indicated in the figure 14 3 If the receiver continues without responding to the MENU key from the remote control then verify the programmat
20. l Guard l SFN SFN IEB For GPSK receivers press the IN key Program mer MENU Remote control or M frontal buttons and by means of number 4 keys select the LNB LO frequency typ 10600 or 09750 To select the other input parameters press successively the IN w key With number 4 keys select the required transponder frequency 10700 12750 the transmission symbol rate for example 22000 the LNB power supply one receiver for LNB the required polarity of the LNB Quatro Recommended VER 14V HOR 18V and the activation of 22KHz for the high band of an universal LNB The following menus will appear in the programmer and in tv set OSD Remote control TV Set OSD LNB Freq F Tune Frequency Strate i Symbol Rate LNB Ctrl LNB Power Polarity Polarization Tone 22KHz 22KHz Tes Info Press the VIDEO key Programmer RED key Re mote control or M frontal buttons After a few seconds the screen will display LOCK OK indicating that the tuner has been locked The WAIT PAT message will appear while the unit scans the channels and then the first program of the transponder will appear Note In case the channels do not appear NO TAB please revise the previous adjustments Use the w key to select the required video program The following menus will appear in the programmer and in tv set OSD Remote control TV Set OSD Input Menu TVE 1 TVE 2 Audio Telecinco Output Antena 3 Te
21. ming mode after 30 seconds without detecting any key being pressed EB INSTALLATION AND CHANNEL TUNING Connect the video output of the receiver which you want to tune to the AV input of one television to view the menus Refer now the following steps you have two option TUNING OPTION DIRECTLY FROM THE STATION If the receiver is in the non programming position red led blinking every sec press the front key M to enter again in programming mode red led blinking every 0 5 sec and then press ESC EXIT or M twice as in the previous section It will appear the fol lowing menu Television HEADEND INSTALLATION User Installation System Configuration Channel Organizing Program Guide Games By means of the keys aw lt p Remote con trol focused to the front sensor of the receiver or their push buttons you will be able to access to the menus of the paragraph J and tune in the chan nels TUNING OPTION FROM VDI LINK We recommend that before installing the VDI LINK in the user socket first to install it in the head end out put Connect the VDILINK according to the Fic11 if you use the amplifier or according to the FIG12 if you use another amplifier type In this last case you need an 11MHz by pass Depending on how you have programmed the receiver cards refer to paragraph H6 put the VDI LINK switch in HOTEL position 0111111 or USER position See Fic17 for the RF output channel of th
22. n of the channel if the broadcaster has send it Pressing the EPG key will appear the complete GUIDE of programs channels refer to the section M This option is only available in UserLink mode To make disappear the information press the ESC key ASSEMBLY OF THE VDI LINK IN THE HOTEL RECEPTION refer to the section F 1 Once the channels are tuned and tested on the head end the VDI LINK kit can be installed in the Hotel reception If User mode is required follow the indications of the section R2 The figures 13 14 and 16 indicate different exam ples of configurations To tune the channels from the Hotel reception follow the same steps carried out in head end sections P and Q Nevertheless it will be necessary to tune the television to the V UHF channel corresponding to the receiver that we want to visualize 2 The main configuration of the receiver can also be modified in this stage sections J to Q Note When you finish installation we recomend to block all installation menus see step 16 ASSEMBLY OF THE VDI LINK WITH THE USER MODE refer to section F 1 Once the channels are tuned and tested on the station with VDI LINK installed on the head end pro ceed to install the VDI LINK in each subscriber out let Remember each user will control a single card Therefore it will be necessary to adjust the switch of each VDI LINK according to the table 17 and the out put channel assigned to the user The televis
23. nnels Switches ON ALL Standards 1 2 3 4 5 ALL Standards 2 3 ALL Standards 1 2 3 4 5 ALL Standards 11213 5 S9 516 NO 3 4 E48 E49 54 517 E50 S5 18 E51 S6 19 E52 57 520 E53 S8 21 E54 SPH HP HR _ HS AJTAJA S9 922 523 E55 E56 E5 U1 uUu1 u1 U1 U1 U1 OI E57 E6 25 E58 E7 E8 527 59 E60 E9 E61 Op OF OF OF U1 U1 WI E62 31 E63 OF OT WI 64 532 65 533 66 534 67 535 U1 OF U1 68 536 69 511 537 S12 S38 S13 39 UT U1 UT OI 14 40 NMP NM NIL NINMINMINININININIENINIENIE NIN INININININ INI NM NM NM NMP NMOL NMI NMNINMIENIN NIN IN I MI NM NM NM WwW Ww Ww Ww iw Ww Ww CO SPH HH SPL RL HR SR RP BI RTA 15 FIG 17 a USER CODE FOR VHF OUTPUT CHANNELS 7 541 Ww WW Ww Ww Ww Dw ws OO SPH HP HP HH H
24. oritos imbios Exit Salir Info system This menu allows to know the following data System configuration gt System information Loader version Loncer verison Exit Suit K Data transfer This menu allows to import and export channel lists and firmware from one receiver to other modules Option available according to the software version Hir FA Lingrada CHANNEL MANAGEMENT MENU This menu allows to manage the general list of pro gram To do this process use the keys to high light the left window On this screen you will be able to do the following S Select a channel By means of or aw E Delete a channel By means of red key E Delete the coded channels green key E Move a channel By means of blue key Order Alphabetically by number yellow key Add to favourite By means of the FAV key select the right window to the desired list of favourite FAV1 to FAV8 Afterwards press the OK key To leave the menu press EXIT Otherwise to manage the favourite channel list press the 4 keys to highlight the right window Next by means of the FAV key select the favour ite list to be managed With this option you will be able to move a channel to delete it and also to delete all the channels of the corresponding FAV list in a simi lar way as with the general list PROGRAMMING GUIDE MENU This menu allows to visualize the program electronic guide Information
25. ous sec tion Mm Satellite Select the desired satellite E Transponder Select the desired transponder for the orientation of the antenna and signal level among all those available on the memorized list If you want to add or to remove transponders then go to the Installation Manual search menu E Position When needed that the motor rotates to the position of the selected satellite press OK in the option to GO TO THE POSITION OK If you want to store a new position obtained with Moving anten na then select with the keys 8 the option KEEP POSITION and press OK To reset the motor press the red key Reset of the motor With the green key the signal will automatically be optimized Move antenna By means of the keys 4 you will be able to move the antenna West East Select with the blue key the movement type step by step or continuous mode When concluding the adjustments of this menu you will be able to press OK to look for the channels avail able in the satellite Automatic search menu or EXIT to leave the adjustments During all the process two level bars are displayed to inform about the power and signal level User Installation Automatic Search Menu This menu configures the automatic search of channels in all the memorized transponders Parameters to be ad justed LEa MEHRI G gt MAL LLL Lu tein mads 27 See et cs eles a PES ak
26. re update program is available in your PC connect the receiver to the serial port with MS2696 cable Send the update file using the Hyperterminal program included in Windows After sending the or der connect the receiver to power supply Tuner demodulator Input frequency Input level Bandwith Demodulation Constellation Guard interval FEC Symbol rate Input frequency Input level IF Bandwith Demodulation FEC LNB Power Supply General Dimensions Temperature Supply voltage Modulator Modulator type Standards Audio subcarriers Mixing losses Output level Spureous VSB Amplifiers Terrestre Inp frequency Max gain Out level DIN45004B RF Mixing Loss VDI TNT 174 230 470 862 MHz lt lt lt lt 35 85 dBuV 6 7 8 MHz Auto OFDM 2 K 8 K mode QPSK 16 QAM 64 QAM 1 32 1 16 1 8 1 4 Auto 1 2 2 3 3 4 5 6 7 8 up to 60 Msimb seg VDI SAT 950 2150 MHz 25 65 dBm 36 MHz max QPSK ETS 300421 Auto 1 2 2 3 3 4 5 6 7 8 13V 18V 200 mA 0 22 KHz VDI TNT VDI SAT 200 x 110 mm 5 a 455 24 12 5 3 3 VDC Note Max two LNB for each DigiCompact8 18dVc amp 500mA max TECHNICAL CHARACTERISTICS Amplifiers VDI AMP 120 862 MHz 38 dB 0 20 110 dBuV 1 5 dB 47 862 MHz TECHNICAL CHARACTERISTICS QPSK OFDM Receivers Video decoder System Video format Audio decoder System Sample freq Audio format Programmer Display Keys Interface VDI
27. rogramming and feeding the module IE CONNECTIONS AND INSTALLATION NOTE While you carry out the connections assure yourself that general feeding at 280V is disconnected Connect the power supply cable Ficsp and input bridges Fic 6 7 In FiG10 there is an example with 4 OFDM 4 GPSK For OFDM receivers we recommend to make groups of two receivers and use a distribu tor before riceA For wide band amplification con nect RF bridges to the outputs Fics with load on the unused connector OUTPUT LEVEL ADJUSTMENT Connect the feeding cable to the central and to the network To start the process it s very impor tant to reduce to minimum the adjustment of RF level of all receivers Fics and amplifier Under these conditions measure the maximum channel level at the amplifier output by means of an analyzer Then you should equalize all channels to this value by means of RF level ric3 and after that adjust the amplifier gain at the desired general level Fic 2 SMATV SYSTEM SMATV SYSTEM is the preconfigured system from factory If you have already changed to LINK SYS TEM please go to step H1 2 3 and select SMATV In SMATV System programmation is done directly on the station Connect the power supply after having done the connections NEVER THE OPPOSITE To program a certain receiver you have three pos sibilities By means of the programmer by means of the infrared remote control
28. s Info Canal NOTE If the program is coded an asterisk or will appear on the screen 15 Press the AUDIO key Programmer GREEN key Remote control or M frontal buttons and by means of gt W keys select the required audio program and mode stereo mono L R The following menus will appear in the programmer and in tv set OSD Remote control TV Set OSD Input Menu pid 0203 Stereo Video Right left mono Audio Pid 0204 Stereo Right left mono NOTE The receiver starts automatically in STEREO or MONO according to the type of modulator incorporated in the receiver BEI Press the OUT key Programmer YELLOW key Re mote control or M frontal buttons and by means of P keys select the required video standard PAL SECAM To select the other output parameters press successively the OUT W key With 4 keys select the RF standard B G 1 L D K BB the band E S the output channel E5 E69 503 541 the audio subcarrier 4 5 5 5 6 6 5 the sound level and subtitles if exists The following menus will appear in the programmer and in tv set OSD Remote control TV Set OSD F Mode Input Menu Mode tandard Video Standard Audio Band Channell Output Channel Tes Info Audio SC ound C Volume olume Subtitles ubtitle 1J Press the OK key the message STORED and READY will appear on the programmer display and the menu will disappear from tv set indicating that the chan
29. uration Menu available only on the satellite GPSK cards User Link configuration Pesstierer eanl iquratian Channel Auti Fr itifi guida Manual Search 5 1 amar DT Top Id This menu allows to configure the LNB antenna to a certain satellite In the case of having several connected antennas to the receiver by means of a DiSEqC switch then it will be necessary to configure this menu for each dish In Hotel Link mode we always recommend to use QUATRO LNBs with QPSK boards connected to the de sired outputs You can also use a DiSEqC switch see fig 15 amp 16 Parameters to be adjusted User instalation Lrib configoratior Select jour deaired tatelite Ox Save ranges Exil Qu Satellite Select the desired satellite by means of the keys 4 E DiSEqC Mode only in case of multiple antenna installation Select the DiSEqC value correspond ing to the input of the DiSEqC switch used by an tenna to be configured DiSEqC A B C D Tone A B OFF Low frequency Value MHz of the OL Local Oscillator of the LNB for the low band See LNB label 9 750MHz for universal LNBs m High frequency Value in MHz of the OL of the LNB for the high band see LNB label 10 600MHz for universal LNBs E Tone of 22KHz For Quatro LNBs use ON for high band outputs and OFF for low band out puts For DiSEqC switches or Universal LNBs use AUT
Download Pdf Manuals
Related Search