USER MANUAL - Kramer Electronics
Contents
1. 1 TP on an RJ 45 connector OUTPUTS 1 TP on an RJ 45 connector 1 UXGA on a 15 pin HD connector F 1 Digital audio on an RCA connector 1 Unbalanced stereo audio on a 3 5mm mini jack 1 Bidirectional RS 232 serial port on a 3 pin terminal block VIDEO RESOLUTION Up to WUXGA 1080p MAX OUTPUT LEVEL Video 1 1V Audio 2 2V BANDWIDTH Audio 20Hz 20kHz 3dB S N RATIO Audio 84dB unweighted AUDIO COUPLING AG TND N Audio 0 02 unweighted TOTAL GAIN Analog analog 0dB Analog SPDIF 12dBFS RS 232 BAUD RATE 9600 19200bps MODE Full duplex POWER CONSUMPTION 12V DC 206mA 12V DC 235mA TRANSMISSION DISTANCE Up to 250m 820ft OPERATING TEMPERATURE 0 to 40 C 32 to 104 F STORAGE TEMPERATURE 40 to 70 C 40 to 158 F HUMIDITY 10 to 90 RHL non condensing DIMENSIONS 12 1cm x 7 18cm x 2 48cm 4 76 x 2 83 x 0 98 W D H WEIGHT 0 2kg 0 44lbs approx each ACCESSORIES Power supply OPTIONS RK 3T 19 rack adapter LIMITED WARRANTY The warranty obligations of Kramer Electronics for this product are limited to the terms set forth below Whatis Covered This limited warranty covers defects in materials and workmanship in this product What is Not Covered This limited warranty does not cover any damage deterioration or malfunction resulting from any alteration modification improper or unreaso2. from a laptop to the Audio In 3 5mm mini jack 2 On the TP 126xl connect The UXGA Out 15 pin HD F connector to the video acceptor for example an AV display system The RS 232 3 pin terminal block to the controlled device for example an AV display system The Audio Out Analog 3 5mm mini jack to the unbalanced stereo audio acceptor for example an AV display system with speakers The Audio Out S PDIF RCA connector to the digital audio acceptor for example a DAT recorder 3 Using STP cabling connect the TP 125xI Line Out RJ 45 connector to the TP 126x1 Line In RJ 45 connector see Section 2 3 4 Connect the power adapters to the power sockets on the TP 125xl and TP 126x1 and connect the adapters to the mains electricity not shown in Figure 5 5 If necessary adjust the level and equalization for an optimum picture see Section 6 2 6 Operating the TP 125xl and TP 126xI 6 1 Capturing the EDID The TP 125xl is programmed with a default EDID To replace the default EDID you can replace it with the EDID from a display device To capture a new EDID e With the display device connected to the TP 125xl press the EDID Capture button on the front panel of the TP 125xl If the EDID is successfully captured the Status LED flashes slowly for a few seconds and then lights solid If the EDID is not successfully captured the Status LED flashes quickly for a few seconds then lights solid when the default
3. EDID is loaded 6 2 Adjusting the Level and Equalization on the TP 126xl You can manually adjust the signal level and equalization using the trimmers on the front of the TP 126xI to achieve an optimum picture To adjust the level and equalization on the TP 126xl 1 Use a small screwdriver to slowly turn the Level trimmer clockwise to increase or anticlockwise to reduce the signal level of the TP 126xl 2 Use a small screwdriver to slowly turn the EQ trimmer clockwise or anticlockwise until you achieve an optimum picture 10 TP 125xI TP 126xl Operating the TP 125xl and TP 126xl 7 Wiring the Twisted Pair RJ 45 Connectors When using STP cable connect solder the cable shield to the RJ 45 connector shield Figure 6 defines the TP pinout using a straight pin to pin cable with RJ 45 connectors EIA TIA 568B Figure 6 TP Pinout Wiring PIN Wire Color Orange White Orange Green White Blue Blue White Green Brown White Brown ES IEEE Pair1 4 and 5 Pair2 1 and 2 Pair 3 3 and 6 INI Iaoa KB oO N Warning Using a TP cable that is incorrectly wired will cause permanent damage to the device TP 125x1 TP 126x1 Wiring the Twisted Pair RJ 45 Connectors EH 8 Technical Specifications INPUTS 1 UXGA on a 15 pin HD connector F 1 Unbalanced stereo audio on a 3 5mm mini jack 1 Bidirectional RS 232 serial port on a 3 pin terminal block
4. 2 TP 125xl UXGA Audio Data Line Transmitter Rear Panel Feature Function 4 UXGA IN 15 pin HD Connect to a computer graphics source see Section 5 Connector F 5 LINE OUT RJ 45 onnect to the Line In RJ 45 connector on the TP 126xl Connector see Section 2 3 RS 232 Serial Port 3 pin Connect to an RS 232 device PC or controller Terminal Block Note The RS 232 link is bidirectional AUDIO IN 3 5mm Mini Connect to an unbalanced stereo audio source see Section 5 Jack 12V DC Power Connector Connect to one of the supplied 12V DC power adapters Center pin positive TP 125xI TP 126xl Defining the TP 125xI TP 126x1 Line Transmitter and Receiver 4 2 Defining the TP 126xl UXGA Audio Data Line Receiver Figure 3 defines the front panel of the TP 126xI UXGA Audio Data Line Receiver TP 1 26x Figure 3 TP 126x1 UXGA Audio Data Line Receiver Front Panel Function LINK LED Lights green when the TP link is established LEVEL Trimmer Use to adjust the output signal level see Section 6 2 Use to adjust the cable compensation equalization level ONLED Lights green when the device is powered on Figure 4 defines the rear panel of the TP 126xl UXGA OUT LINEIN RS 232 AuoioouT _ 12VDC Figure 4 TP 126x1 UXGA Audio Data Line Receiver Rear Panel Feature Function UXGA ae pin HD Connect to a computer graphics video acceptor see Section 5 Connector F LINE IN RJ Connector Connect to the Line Out RJ 45 conne
5. APPLY TO YOU AND ALL IMPLIED WARRANTIES ON THIS PRODUCT INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR THE PARTICULAR PURPOSE SHALL APPLY AS PROVIDED UNDER APPLICABLE LAW Other Conditions This limited warranty gives you specific legal rights and you may have other rights which vary from country to country or state to state This limited warranty is void if i the label bearing the serial number of this product has been removed or defaced ii the product is not distributed by Kramer Electronics or iii this product is not purchased from an authorized Kramer Electronics reseller If you are unsure whether a reseller is an authorized Kramer Electronics reseller please visit our Web site at www kramerelectronics com or contact a Kramer Electronics office from the list at the end of this document Your rights under this limited warranty are not diminished if you do not complete and return the product registration form or complete and submit the online product registration form Kramer Electronics thanks you for purchasing a Kramer Electronics product We hope it will give you years of satisfaction For the latest information on our products and a list of Kramer distributors visit our Web site where updates to this user manual may be found We welcome your guestions comments and feedback Web site www kramerelectronics com KRAMER E mail info Okramerel com SAFETY WARNING Disconnect the unit from the power e supply before op
6. KRAMER ELECTRONICS LTD USER MANUAL MODELS TP 125xI WUXGA Audio Data Line Transmitter TP 1 26xI UXGA Audio Data Line Receiver P N 2900 300206 Rev 3 EE TP 125x1 TP 126x1 Quick Start Guide This guide helps you install and use your product for the first time For more detailed information r go to http www kramerelectronics com support product_downloads asp E to download the latest manual or scan the QR code on the left Step 1 Check what s in the box A TP 125xl or TP 126xI UXGA Audio Data Line Transmitter or Receiver 1 Power adapters 12V DC output 1 Quick Start Guide 4 Rubber feet RR K Step 2 Install the TP 125xl or TP 126xl Mount the devices in racks using the optional RK T2B rack adapter available for purchase or attach the rubber feet and place them on shelves Step 3 Connect the inputs and outputs Always switch off the power to all devices before connecting them to your TP 125xl1 or TP 126xI P a bo D RS 232 AUDIO IN PC Video 00000 00000 00000 TP 126xl Rear Panel To RS 232 Controlled ice Step 4 Connect the power Connect the power adapters to the TP 125xl and TP 126x1 and plug the adapters into the mains electricity Contents 1 Introduction 2 Getting Started 2 1 Achieving the Best Performance 2 2 Safety Instructions 2 3 Shielded Twisted Pair Unshielded Twisted Pair 2 4 Recycling Kramer Products 3 Overview 4 Defi
7. PURCHASE PRICE PAID FOR THE PRODUCT TO THE MAXIMUM EXTENT PERMITTED BY LAW KRAMER ELECTRONICS IS NOT RESPONSIBLE FOR DIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR CONDITION OR UNDER ANY OTHER LEGAL THEORY Some countries districts or states do not allow the exclusion or limitation of relief special incidental consequential or indirect damages or the limitation of liability to specified amounts so the above limitations or exclusions may not apply to you Exclusive Remedy TO THE MAXIMUM EXTENT PERMITTED BY LAW THIS LIMITED WARRANTY AND THE REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES REMEDIES AND CONDITIONS WHETHER ORAL OR WRITTEN EXPRESS OR IMPLIED TO THE MAXIMUM EXTENT PERMITTED BY LAW KRAMER ELECTRONICS SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IF KRAMER ELECTRONICS CANNOT LAWFULLY DISCLAIM OR EXCLUDE IMPLIED WARRANTIES UNDER APPLICABLE LAW THEN ALL IMPLIED WARRANTIES COVERING THIS PRODUCT INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL APPLY TO THIS PRODUCT AS PROVIDED UNDER APPICABLE LAW IF ANY PRODUCT TO WHICH THIS LIMITED WARRANTY APPLIES IS A CONSUMER PRODUCT UNDER THE MAGNUSON MOSS WARRANTY ACT 15 U S C A 2301 ET SEQ OR OTHER APPICABLE LAW THE FOREGOING DISCLAIMER OF IMPLIED WARRANTIES SHALL NOT
8. UP 7 Scan Converters and Scalers GROUP 8 Cables and Connectors GROUP 9 Room Connectivity GROUP 10 Accessories and Rack Adapters and GROUP 11 Sierra Video Products Thank you for purchasing the Kramer TOOLS TP 125x1 UXGA Audio Data Line Transmitter and or TP 126xl UXGA Audio Data Line Receiver which are ideal for e Presentation and multimedia applications e Long range graphics distribution for schools hospitals stores and security applications 2 2 1 2 2 Getting Started We recommend that you e Unpack the equipment carefully and save the original box and packaging materials for possible future shipment e Review the contents of this user manual Go to http www kramerelectronics com support product downloads asp to check for up to date user manuals application programs and to check if firmware upgrades are available where appropriate Achieving the Best Performance To achieve the best performance e Use only good quality connection cables we recommend Kramer high performance high resolution cables to avoid interference deterioration in signal quality due to poor matching and elevated noise levels often associated with low quality cables e Do not secure the cables in tight bundles or roll the slack into tight coils e Avoid interference from neighboring electrical appliances that may adversely influence signal quality e Position your Kramer TP 125xl and TP 126xl away from moisture exce
9. ctor on the TP 125xI See Section 2 3 RS 232 Serial Port 3 pin Connect to the RS 232 device to be controlled Terminal Block Note The RS 232 link is bidirectional ANALOG 3 5mm Connect to an unbalanced stereo audio acceptor see Section 5 AUDIO Mini Jack OUT S PDIF RCA Connect to a digital audio acceptor Connector 10 12V DC Power Connector Connect to one of the supplied 12V DC power adapters Center pin positive TP 125x1 TP 126x1 Defining the TP 125xI TP 126xI Line Transmitter and Receiver 5 Connecting the TP 125xl and TP 126xI Switch off the power to all devices before connecting them to your TP 125xI TP 126xl1 After connecting your TP 125xI TP 126xl1 connect the power to the transmitter and receiver and then switch on the power to the other devices Computer Graphics Audio RS 232 Control TP 125xl ZEz SY AV Display System with Built in Speakers DAT Recorder Figure 5 Connecting the TP 125xI Transmitter and TP 126xl Receiver To connect the TP 125xl and the TP 126xl as illustrated in Figure 5 1 On the TP 125xl connect The computer graphics video source for example the graphics output from a laptop to the UXGA In 15 pin HD connector F E TP 125x1 TP 126x1 Connecting the TP 125x1 and TP 126x1 The RS 232 controller for example a laptop controller with an RS 232 interface to the RS 232 3 pin terminal block An unbalanced stereo audio source for example the audio output
10. ening and servicing P N 2900 300206 Rev 3
11. ft 125x1 TP 126xl Defining the TP 125xI TP 126xl Line Transmitter and Receiver Defining the TP 125x1 TP 126xl Line Transmitter and Receiver This section defines the e TP 125xl UXGA Audio Data Line Transmitter see Section 4 1 e TP 126xl UXGA Audio Data Line Receiver see Section 4 2 The TP 125xl has inputs for e Computer graphics video e Unbalanced stereo audio e RS 232 data The TP 125xl encodes the video audio and data signals and transmits them over STP cable to a TP 126xl receiver RS 232 data and commands flow bidirectionally allowing status reguests and control of a destination unit The RS 232 interface makes it possible to control almost any device over a transmission range of up to 250m over STP cabling The TP 126xl accepts the encoded signal over STP from the TP 125xl and outputs computer graphics video unbalanced stereo audio digital audio and RS 232 data 4 1 Defining the TP 125xl UXGA Audio Data Line Transmitter Figure 1 defines the front panel of the TP 125xl UXGA Audio Data Line Transmitter TP 125x Figure 1 TP 125xl UXGA Audio Data Line Transmitter Front Panel CAPTURE Button Press to capture the EDID from the video display STATUS LED Indicates the following EDID status e Flashes slowly then lights solid new EDID stored e Flashes quickly then lights solid default EDID stored ONLED Lights green when the device is powered on LINE OUT RS 232 Aupio IN 12V DC Figure
12. lation Kramer Electronics will not be responsible for any costs related to any setting up this product any adjustment of user controls or any programming required for a specific installation of this product How to Obtain a Remedy under this Limited Warranty To obtain a remedy under this limited warranty you must contact either the authorized Kramer Electronics reseller from whom you purchased this product or the Kramer Electronics office nearest you For a list of authorized Kramer Electronics resellers and or Kramer Electronics authorized service providers please visit our web site at www kramerelectronics com or contact the Kramer Electronics office nearest you In order to pursue any remedy under this limited warranty you must possess an original dated receipt as proof of purchase from an authorized Kramer Electronics reseller If this product is returned under this limited warranty a return authorization number obtained from Kramer Electronics will be required You may also be directed to an authorized reseller or a person authorized by Kramer Electronics to repair the product If itis decided that this product should be returned directly to Kramer Electronics this product should be properly packed preferably in the original carton for shipping Cartons not bearing a return authorization number will be refused Limitation on Liability THE MAXIMUM LIABILITY OF KRAMER ELECTRONICS UNDER THIS LIMITED WARRANTY SHALL NOT EXCEED THE ACTUAL
13. lectronics will do Kramer Electronics will at its sole option provide one of the following three remedies to whatever extent it shall deem necessary to satisfy a proper claim under this limited warranty 1 Elect to repair or facilitate the repair of any defective parts within a reasonable period of time free of any charge for the necessary parts and labor to complete the repair and restore this product to its proper operating condition Kramer Electronics will also pay the shipping costs necessary to return this product once the repair is complete 2 Replace this product with a direct replacement or with a similar product deemed by Kramer Electronics to perform substantially the same function as the original product 3 Issue a refund of the original purchase price less depreciation to be determined based on the age of the product at the time remedy is sought under this limited warranty What Kramer Electronics will not do Under This Limited Warranty If this product is returned to Kramer Electronics or the authorized dealer from which it was purchased or any other party authorized to repair Kramer Electronics products this product must be insured during shipment with the insurance and shipping charges prepaid by you If this product is returned uninsured you assume all risks of loss or damage during shipment Kramer Electronics will not be responsible for any costs related to the removal or re installation of this product from or into any instal
14. nable use or maintenance misuse abuse accident neglect exposure to excess moisture fire improper packing and shipping such claims must be presented to the carrier lightning power surges or other acts of nature This limited warranty does not cover any damage deterioration or malfunction resulting from the installation or removal of this product from any installation any unauthorized tampering with this product any repairs attempted by anyone unauthorized by Kramer Electronics to make such repairs or any other cause which does not relate directly to a defect in materials and or workmanship of this product This limited warranty does not cover cartons equipment enclosures cables or accessories used in conjunction with this product Without limiting any other exclusion herein Kramer Electronics does not warrant that the product covered hereby including without limitation the technology and or integrated circuit s included in the product will not become obsolete or that such items are or will remain compatible with any other product or technology with which the product may be used How Long Does this Coverage Last Seven years as of this printing please check our Web site for the most current and accurate warranty information Whois Covered Only the original purchaser of this product is covered under this limited warranty This limited warranty is not transferable to subsequent purchasers or owners of this product What Kramer E
15. ning the TP 125xI TP 126xI Line Transmitter and Receiver 4 1 Defining the TP 125xl UXGA Audio Data Line Transmitter 4 2 Defining the TP 126xl UXGA Audio Data Line Receiver 5 Connecting the TP 125xl and TP 126xl 6 Operating the TP 125xl and TP 126xl 6 1 Capturing the EDID 6 2 Adjusting the Level and Equalization on the TP 126xl 7 Wiring the Twisted Pair RJ 45 Connectors 8 Technical Specifications Figures Figure 1 TP 125xl UXGA Audio Data Line Transmitter Front Panel Figure 2 TP 125xl UXGA Audio Data Line Transmitter Rear Panel Figure 3 TP 126xl UXGA Audio Data Line Receiver Front Panel Figure 4 TP 126xl UXGA Audio Data Line Receiver Rear Panel Figure 5 Connecting the TP 125xl Transmitter and TP 126x1 Receiver Figure 6 TP Pinout Wiring NOOO A WHWONMND 00 SI SI 0 OD Introduction Welcome to Kramer Electronics Since 1981 Kramer Electronics has been providing a world of unigue creative and affordable solutions to the vast range of problems that confront video audio presentation and broadcasting professionals on a daily basis In recent years we have redesigned and upgraded most of our line making the best even better Our 1 000 plus different models now appear in 11 groups that are clearly defined by function GROUP 1 Distribution Amplifiers GROUP 2 Switchers and Routers GROUP 3 Control Systems GROUP 4 Format Standards Converters GROUP 5 Range Extenders and Repeaters GROUP 6 Specialty AV Products GRO
16. quiring it to be collected and recycled To comply with the WEEE Directive Kramer Electronics has made arrangements with the European Advanced Recycling Network EARN and will cover any costs of treatment recycling and recovery of waste Kramer Electronics branded equipment on arrival at the EARN facility For details of Kramer s recycling arrangements in your particular country go to our recycling pages at Attp www kramerelectronics com support recycling Overview The TP 125xl and TP 126xl are a high performance TP Twisted Pair transmitter and receiver pair for transmitting computer graphics video unbalanced stereo audio and bidirectional RS 232 data signals over extended distances using CAT 5 6 cable The TP 125xl encodes computer graphics video unbalanced stereo audio and RS 232 data into a TP signal The TP 126xl decodes the TP signal into computer graphics video digital unbalanced stereo audio and RS 232 data signals The TP 125xl and TP 126xl together form an extended computer graphics audio data line transmission and reception system More specifically the TP 125xl and TP 126xl support e Video resolutions up to UXGA 1920 x 1200 e EDID TP 125xl e HDTV e Level gain and equalization peaking adjustment TP 126xl Full duplex bidirectional RS 232 transmission e Increased level of protection against noise spikes and interference in adverse environments e Transmission range of up to 250m 820
17. ssive sunlight and dust This equipment is to be used only inside a building It may only be connected to other equipment that is installed inside a building Safety Instructions Caution There are no operator serviceable parts inside the unit Warning Use only the Kramer Electronics input power wall adapter that is provided with the unit Warning Disconnect the power and unplug the unit from the wall before installing P 125x1 TP 126xl Getting Started 2 3 Shielded Twisted Pair Unshielded Twisted Pair We recommend that you use Shielded Twisted Pair STP cable and stress that the compliance to electromagnetic interference was tested using STP cable There are different levels of STP cable available and we advise you to use the best guality STP cable that you can afford Our non skew free cable Kramer BC STP is intended for analog signals where skewing is not an issue In cases where there is skewing our Unshielded Twisted Pair UTP skew free cable Kramer BC XTP may be advantageous and UTP cable might also be preferable for long range applications In any event when using UTP cable it is advisable to ensure that the cable is installed far away from electric cables motors and so on which are prone to create electrical interference 2 4 Recycling Kramer Products The Waste Electrical and Electronic Equipment WEEE Directive 2002 96 EC aims to reduce the amount of WEEE sent for disposal to landfill or incineration by re
Download Pdf Manuals
Related Search