AUTOMATIC DRUM WASHING MACHINE USER MANUAL
Contents
1. S3 T gt SAFETY INSTRUCTIONS BEFORE SWITCHING THE APPLIANCE ON FOR THE FIRST TIME DO V Make sure that the transport bolt are removed IV sea separate earthed socket for the power supply Make sure that the plug is accessible V Hold the plug and not the electric cable when unplugging the power supply Make sure that the fuses in the power circuit are rated for 15A VI Keep away from heat sources and direct sun light to prevent plastic and rubber components from aging Make sure that the power cord is not caught under or in the appliance and avoid damage to the power cable V Check that hose joints and connections are firm and no water can leak If joints are loose or there is leakage turn off the water supply and refix Do not use the washing machine until the hoses are properly fixed DURING DAILY USE OF THE APPLIANCE DO IV Pul up zips and fix loose threads to prevent the items from being entangled If necessary put small items into a net bag or pillow V Tum off the machine after each wash program and switch it off at the mains to save electricity and for satety Wipe clean the lower part of the porthole Keep the door slightly open when the washing machine is not in use to prevent formation of odours Let the power cord be replaced by the manufacturer his service agent or other accordingly qualified persons in case it is damaged V2. G F E D C B A A Program knob F Delay Button B Power Switch G Detergent distribution drawer C Start Pause Button H Display D Spinning Speed Setting Button E F Combination for keyboard lock E Washing temperature button OPERATIONAL FUNCTIONS A Program knob _ By turning the knob clockwise counterclockwise the required program can be selected There are 11 programs available After a program is selected the corresponding light will go on B Power Switch _ Press this button to switch on the washing machine Press it again to switch it off Start Pause _ When the washing machine is connected to the power socket and a program is selected lightly Button touch this button to start operation During a wash cycle touch it lightly operation will stop and the digits on the screen start blinking Touch it again to resume operation To cancel a wash program during a wash cycle touch this button when the digits on the screen start blinking press the Power switch the program will be cancelled D Spinning Speed _ Touch this button lightly to select the desired speed When a speed is set it will be displayed on Setting Button the screen Note Different water temperatures and spinning speeds can be set for different laundries Wash using the default settings if there is no special requirement E Washing Touch this button lightly the washing temperature will be displayed on the screen Select a temperature according to the type of laund
3. Ensure that the appliance is not used by persons with reduced physical sensory or mental capabilities lack of experience and knowledge without supervision or instruction by a person responsible for their safety Supervise children to ensure that they do not play with the appliance DO NOT Al Touch or use the appliance when barefoot or with wet or damp hands or feet Use flammable detergent or dry cleaning agent Use any flammable sprays in close vicinity to the appliance Remove or insert the plug in the presence of flammable as VA Allow children or infirm persons to play with the appliance or packing materials Z Install the appliance outdoors in a damp place or in an area which may be prone to water leaks such as under or near a sink unit In the event of a water leak allow the machine to dry naturally Place the washing machine directly on a carpet or close to a wall or furniture DO NOT A Touch the washer door during the washing process it ets hot Vi Place heavy objects or sources of heat or damp on top of the appliance Hot wash foam rubber or sponge like materials Open the detergent distribution drawer during the wash cycle i Force the washer door open The door is fitted with a self lock device and will open shortly after the washing procedure is ended Open the washer door if the water level is visibly over the porthole Al Cover the washi
4. Make sure the drain hose is not in water Drain hose is blocked Unblock the drain hose Drain hose end is higher than 100 cm above Make sure the drain hose end is lower than the floor level 100 cm above floor level The filter is blocked Unblock the filter Not all transportation bolts have been removed _ Remove all transportation bolts Washing machine is located on an uneven _ Make sure the washing machine is on surface or is not level an even surtace and levelled Machine load is over 6 kg _ Reduce amount of laundry in the drum Water or electricity failure Check the power supply Washing machine gives an error message Check display codes The detergent is not a low foaming type or for Check if your detergent is appropriate manual wash _ Reduce amount of detergent in the distribution Excessive use of detergent drawer The washing program duration will be adjusted This is normal and doesn t affect the according to the initial water temperature functionality Unbalance of the laundry _ Add clothes or run a spinning program again MPORTANT SAFETY INFORMATION Do not use a multiple socket extension cord A separate earthed socket is required which shall be accessible at all times If the cord becomes damaged it should be replaced by the manufacturer its service agent or similarly qualified person Never remove the plug from the socket by pulling on the cord always gra
5. Caution The filter must be in place or it may lead to leakage 2 Place a container under the drain pump filter to collect any excess water that may come out of the drain pump when the filter is removed WATER INLET VALVE AND INLET VALVE FILTER To prevent blockage to the water supply by ingress of foreign substances clean the water inlet valve and inlet valve filter regularly MOVING THE MACHINE If the machine is to be moved to a distant location replace the transportation bolts removed before installation to prevent damage as shown below Remove the blanking plugs Remove the back cover Insert the synthetic stabilisers and the transportation bolts Tighten the bolts with a spanner Replace the back cover LONG PERIODS OF DISUSE If the washing machine is left idle for a long period pull out the electrical plug and turn off the water supply Open the washer door to prevent formation of moisture and odours Let the door open while not used DISPLAY CODES DISPLAY CODES AND SPECIAL FUNCTIONS CODES CAUSES SOLUTIONS Err Door is not properly shut _ Shut the door properly Err2 Drainage error water not emptied within 4 _ Clean the filter and check the drain hose for blockage If error minutes still exists please contact the maintenance personnel Err3 Temperature sensor not properly connected or _ Contact the maintenance personnel damaged Err4 Heater error App
6. USER MANUAL HMS1400B HMS1400BS HMS12608 HMS1260BS ABLE OF CONTENTS BEFORE USE COMPONENTS 03 gt PREPARATION ss 04 gt SAFETY INSTRUCTIONS 05 gt INSTALLATION 06 SCONTROL PANEL 08 LEGEND lV Yes ZA No Optional USING THE APPLIANCE gt PROGRAM SELECTION gt CONSUMPTION AND TECHNICAL DATA 11 gt WASHING METHODS 16 20 MAINTENANCE gt CLEANING amp CARE ss 16 DISPLAY CODES 18 IROUBLESHOOTING 1 IMPORTANT SAFETY INFORMATION 20 For your safety any instructions in this manual with this Warning sign must be followed strictly DISPOSAL E The symbol on the product or on its packing indicates that this product may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health Which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product COMPONENTS THANKS FOR PURCHASING A HAIER PRODUCT Please rea
7. Spinning speed r min Washing programs Max power W Dimensions HxDxW mm Net weight kg MAX LOAD 6 kg 6 kg 6 kg 3 kg 2 kg 2 kg 2 kg 3 kg 3 kg HMS1460B HMS1460BS ENERGY CONSUMPTION 0 95 kWh 1 14 kWh 0 50 kWh 0 43 kWh 0 42 kWh 0 42 kWh 0 55 kWh 0 36 kWh 0 44 kWh 220 240V 50Hz 10 0 03 P 1 6 1400 11 2000 850 x 565 x 595 68 WATER CONSUMPTION 64L 49L 53L 39L 40L 39L 34L 36L 15L HMS1260B HMS1260BS 220 240V 50hz 10 0 03 P 1 6 1200 1 2000 050 x 565 x 595 60 TEMPERATURE 40 C 60 C 40 C 40 C 40 C 40 C 40 C 40 C 40 C WASHING TIME 2 40 h 2 58 h 2 22 h 1 28 h 1 08 h 1 08 h 1 02 h 0 34 h 0 53 h ASHING METHODS This washing machine is for domestic use only If the machine is use for commercial purpose the guarantee will not be valid anymore Do not use it for purposes other than that for which it was designed Follow the instructions given on the label of each garment and wash only machine washable garments POWER SUPPLY Connect the washing machine to the power supply 220V to 240V 50Hz WATER CONNECTION Turn on the tap The water must be clean and clear Note Before use check for leakage in the joints between the tap and the inlet hose by turning on the tap PREPARING THE LAUNDRY Sort out clothes according to fabric cotton synthetics wool or silk and to how dirty they are Separate white clothes from
8. of electric shock Remove the fuse betore disposal There is a danger of electric shock if the cut off plug is inserted into any 13 amp socket outlet How to wire a 13 amp plug UK Only The wires in the mains lead on this appliance are coloured in accordance with the following code Green and Yellow Earth Blue Neutral Brown Live As the colours may not correspond with the markings identifying the terminals in your plug proceed as follows The green and yellow wire must be connected to the terminal in the plug which is marked with the letter E or with the earth symbol or coloured green and yellow The blue wire must be connected to the terminal marked N The brown wire must be connected to the terminal marked L You must make sure the lead is firmly secured under the cord clamp WATER CONNECTION The product should be connected to the water main using new hose sets old hose sets should not be reused The water pressure must not be less than 0 03MPa Tel 39 0332 24511 m Haier Europe Trading S r l a e Via De Cristoforis 12 Fax 39 0332 245146 21100 Varese Italy E mail het srl haiereurope com
9. coloured ones Wash them first by hand to check if they fade or run Empty pockets keys coins etc and remove the harder decorative objects e g brooches Attention Small parts like buttons etc may lead to repair work which user has to pay by themselves and can cause damage in the machine Garments without hems underwear finely woven textile such as fine curtains are to be put into wash bag it is better not to wash them in a washing machine lose zippers and hooks make sure the buttons are sewn on tightly and place small items such as socks belts bras etc in the wash bag Untold large pieces of fabric such as bed sheets bedspreads etc 4 Turn shirts inside out LOADING THE MACHINE Open the washer door put in the laundry piece by piece Close the door tightly When first using the washing machine let it run unloaded for one program to prevent the laundry from being tainted by oil or dirty water from the washing machine Before washing you should run the machine without laundry but with detergent with 60 C program Do not overload the washing machine SELECTING DETERGENT The washing efficiency and the performance is determined by the quality of detergent used Special non foaming detergent produces good washing results Use specitic detergents for synthetic and woollen goods Do not use dry cleaning agents such as trichloroethylene and similar products Note Do not add more detergent t
10. d these instructions carefully before using this appliance The instructions contain important information which will help you get the best out of the appliance and ensure safe and proper installation use and maintenance Keep this manual in a convenient place so you can always refer to it for the sate and proper use of the appliance If you sell the appliance give it away or leave it behind when you move house make sure you also pass on this manual so that the new owner can become familiar with the appliance and safety warnings ACCESSORIES Check the accessories and literature in accordance with this list 1x Inlet hose assembly Ix Bottom Cover For HMS1460B S HMS1260B S 1x User manual 1x Drain hose bracket 1x Warranty card optional 3x Blanking plugs e PREPARING THE MACHINE Remove all the packing materials to prevent unsteadiness including the polystyrene base Upon opening the package water drops may be seen on the plastic bag and the porthole This is normal phenomenon resulting from water tests in the factory DESCRIPTION This diagram may be slightly different from the layout of the washing machine you have just purchased due to technical improvements Control panel Drain hose Door handle Neier inlet valve Work top Power cord Washer door Back cover Detergent distribution drawer Back cover screws Transportation bolts Filter cover MIS VUL UM a TI
11. ears at the end of a cycle Reduce load and then start washing again If problem still exists please contact the maintenance personnel Err5 Water level not met in 8 minutes _ Make sure that tap is turned on and water pressure is normal If problem still exists please contact the maintenance personnel The drain hose is in water _ Make sure the drain hose is not in water Err7 Motor overheat protection or damage _ Contact the maintenance personnel Err8 Water exceeds protective level _ Contact the maintenance personnel End End of wash cycle 1 25 The remaining time is 1 hour 25 minutes After the last rinsing cycle finishes spining fails TT completely due to animbalance of the laundry Control panel lock function Press the Delay and the Temperature buttons simultaneously for 3 seconds after starting a program It can no longer be changed by operating buttons or knobs To unlock press the Delay and Start Pause buttons again for 3 seconds Power off memory function In case of abrupt power failure or the need to cut off the power during a program cycle the present settings will be saved and the preset operation will resume when the power is on again To cancel a program Press the Start Pause button then switch off the power and the program is automatically cancelled Turn the program selector again to choose another program TROUBLESHOOTING TROUBLESHOOTING The following circumstances do not cons
12. ess the key combination again to cancel this function PROGRAM SELECTION PROGRAM MODES 7 Temperature Program Maximum Preset 2 3 1 Prewosh f090 C 40 C FT MI 2 Gm 90 or T 7 3 Synthetic 60 C OC LIA 4 Wool o40 C 4C V O A 5 Cashmere to40 C OT POY 6 Sik w 4 DT pa EI 1 Quick 040 4C LA DAI EZ Mosh 060 OT Vp 9 Rinse A L u 10 Si ula 1 Drain A Va VA ZI Yes Zj No Optional 1 Detergent compartment for prewash mode 2 Detergent compartment 3 Compartment for softener and other additives Preset spin speed Recommended Laundry HMS1460B S HMS1260B S Heavy soiling 1000 rpm 1000 rpm Cotton fabrics 1000 rpm 1000 rpm Fast colour synthetic 1000 rpm 1000 rpm Woolen fabrics 600 rpm 600 rpm Cashmere fabrics 600 rpm 600 rpm Silk fabrics 400 rpm 400 rpm Medium soil 1000 rpm 1000 rpm Medium soil 7 Attention This program consists only main wash without rinse and spin Medium soil 1000 rpm 1000 rpm 7 1000rpm 1000 rpm CONSUMPTION TABLE The wash cycle times are intended as a guide only The actual time used may vary due to ditferent water pressure initial water temperature etc PROGRAM Prewash Cotton Cotton Synthetic Wool Cashmere Silk Quick Wash EN 60456 test program Energy label program with Cotton 60 C and max spin speed TECHNICAL DATA Power source Max working current A Water pressure MPa Nominal load kg
13. han needed Please follow the dosage recommendation on the detergent package ADDING DETERGENT Slide out the detergent drawer and put the required detergent and softening agent into the corresponding compartments Push back the drawer gently Refer to the instructions on the drawer Caution For prewashing program detergent should be added to both compartments 1 and 2 For other programs do not add detergent to compartment 1 Use liquid detergent according to the instructions on its package Do not use liquid detergent if the prewash mode or Start delay is selected Do not overuse softener otherwise it will damage the artificial fibers SELECTING PROGRAM To get the best washing results an appropriate washing program should be selected according to the laundry type There are instructions on the handle of the detergent distribution drawer Please turn the program knob to select the right program SELECTING FUNCTIONAL Select the required options Reter to the Control panel pages 06 and 07 SETTING WASHING TEMPERATURE Press and hold down the temperature button until the desired temperature is selected or the symbol for no water heating SETTING SPIN SPEED Press and hold down the speed button until the desired speed is selected or the symbol 0 is selected for no spin See Operational functions on the Control panel pages 06 and 07 for selecting temperature and spin speed I
14. ith any solvent OO Don t tumble dry EF Dry clean only B Dry cleaning with peridoride Wool Seal Dry cleaning with aviation fuel LOAD REFERENCE Bed sheet single Cotton Approximately 800g Blanket Wool Approximately 3000g Blended fabric dothes Approximately 800g Jackets Cotton Approximately 800g Jeans Jl Approximately 800g Overalls Cotton Approximately 950g Ladies Pyjamas J Approximately 200g Shirts Approximately 300g Socks Blended fabrics Approximately 50g T Shirts Cotton Approximately 300g Underwear Blended fabrics Approximately 70g CLEANING amp CARE AFTER WASHING Turn off the water supply and pull out electricity plug after each wash Open the washer door to prevent formation of moisture and odours If the washing machine is left idle for a long period drain the water in the machine and replace the drain hose CLEANING THE DETERGENT DRAWER Clean the detergent distribution drawer regularly Swing out the drawer flush it clean with water and then replace it CLEANING THE MACHINE Unplug the machine during cleaning and maintenance Use a soft cloth dampened with soap liquid to clean the machine case and rubber components Do not use organic chemicals or corrosive solvents CLEANING THE FILTER Clean the filter once a month 1 Open the bottom cover 2 Remove the filter by turning counterclockwise 3 Flush the filter clean with running water 4 Replace the filter by turning clockwise and remount the cover
15. ng machine with plastic cover so that inside dampness cannot be kept in INSTALLATION ADJUSTING THE BOTTOM COVER ee L x When open the shrink package you will find a calcium plastic board i which is laid on the top of washing machine as shown in fig 1 The board is used for reducing noise by pasting it under the cabinet when setting as shown in fig 2 For HMS1460B S HMS1260B 5 Fig 1 Fig 2 DISMANTLE THE TRANSPORTATION BOLTS The transportation bolts are designed for damping anti vibration components inside of the washing machine during the transportation process Remove the back cover 2 Remove the three bolts on the rear side and take out the synthetic stabilisers from within the machine 3 Replace the back cover 4 Fill the holes left by the bolts with blanking plugs Note 1 When yov replace the back cover the convexity must face to outside and you have to insert the back cover from the two gaps as shown in fig 3 2 Keep the transportation bolts and synthetic stabilisers in a safe place for later use ADJUSTING THE WASHING MACHINE There are adjustable feet under the bottom of the washing machine Before use they should be adjusted so that the machine is level This will minimise vibrations and thus noise during use It will also reduce wear and tear We recommend using a spirit level to level the appliance The floor should be as stable and flat as p
16. ossible INLET HOSE 1 Connect the nut on the inlet hose to the connector on the water valve 2 Apply inlet hose to a water tap with cold fresh water Note Use the hose set supplied with the appliance Old hose sets should not be reused DRAIN HOSE 1 Use the drain hose bracket to keep the end of the drain hose retained and prevent the outflow of water Don t extend the length of the drain hose if an extended hose is required please consult a serviceman 2 The height of the drainage outlet must be 80 100 cm Fix the drain hose to the clip at the back of the washing machine to prevent it from dropping off Note The drain hose should not be submerged in water and should be securely fixed and leak free If the drain hose is placed on the ground or if the pipe is at a height of less than 80cm the washing machine will continuously drain while being filled self siphoning CONNECTING TO THE POWER SUPPLY Before connecting to the power supply check The socket is adequate for the maximum power of the washing machine For safety fuses in the power circuit should be rated for no less than 15A The voltage should meet the requirement The power outlet should be capable of accepting the washing machine plug Connect the machine to an earthed socket outlet CONTROL PANEL Haier 1 3 4 5 6 7 8 Prewash Cotton Synthetic Wool Cashmere Silk Quick Wash Rinse in Drain temperature button
17. ry E F Delay Button Detergent distribution drawer Display Combination for keyboard lock Touch this button lightly the washing machine will start operation after a period of time and the corresponding indicator will go on The range is 0 5 24 hours each touch of this button increases a half hour After the button is set press the Start Pause button to start countdown of the set time the time is displayed on the screen until the program ends Note The delay time must be longer than the program time otherwise the washing machine will start the wash program directly Open the drawer three compartments can be seen Compartment 1 Prewash detergent Compartment 2 Detergent for programs 1 to 8 Compartment 3 Softener conditioning agent perfume etc _ Information as remaining wash time temperature and speed setting and error messages will be shown here Note After power is switched on the display will go on and the remaining wash time decreases As the water pressure and temperature may differ the remaining time maybe adjusted accordingly When the laundry is not balanced during spinning the time may be automatically prolonged These are normal phenomena E F Combination for keyboard lock After a programme is started press these two keys simultaneously the sign LOCK and the remaining washing time are displayed on the LED alternately Now all the function keys except the Power switch can be locked Pr
18. sp the plug The door may get hot during use keep children away whilst the machine is operating Never open the detergent drawer while the machine is running When installing the product make sure the mains cord is not trapped or twisted WARNINGS THIS APPLIANCE IS INTENDED FOR DOMESTIC USE ONLY COMMERCIAL OR ANY OTHER USE MAY INVALIDATE THE WARRANTY AND MIGHT BE DANGEROUS Never touch or operate the machine with wet hands or when bare footed Do not put the machine on a carpet that can block the ventilation slots on the bottom of the unit Do not install this machine outdoors or in a damp place Do not install this product near a heat source or in direct sunlight Do not place any object on the machine when it is operating Caution To prevent electric shock disconnect from the main before removing the cover Warning This appliance must be earthed The appliance must be connected to a 220 240 volts 50 cycle AC supply by means of a three pin socket suitably earthed and should be protected by a 13 amp fuse in the plug The appliance is supplied with a standard 13 amp 3 pin plug fitted with a 13 amp fuse Should the fuse require replacement it must be replaced with a fuse rated at 13 amps and approved to BS1362 If the mains plug is unsuitable for the socket outlet in your home or is removed for any other reason then the cut off plug should be disposed of safely do not insert the cut off plug into a mains outlet to prevent the hazard
19. t is advisable to select the recommended value WASHING Press the Start Pause button The washing machine will operate according to the preset programs The washing machine will stop operation automatically when a washing cyde ends The End sign will appear on the display Open the washer door and take out the laundry AFTER WASHING Turn off the water supply and unplug the power cord Open the washer door to prevent formation of moisture and odours Let the door open while not used TIPS FOR SAVING ENERGY 1 Collect clothes for one full wash load 2 Avoid overloading the washing machine 3 Prewash only heavily soiled clothes 4 Reduce the amount of detergent or choose standard or delicate wash programs for slightly soiled clothes 5 Choose a proper washing temperature Modern detergents can wash with very good result already in lower temperature than 60 C Only use higher temperature than 60 C for heavily soiled laundry 6 Follow the dosage recommendation on the detergent package to avoid using too much detergent CARE CHART TOF Resistant material AN Bleachable in cold water e Don t dry dean X27 Delicate fabric zx Do not bleach Dry flat Washable at 95 C ed Iron at 200 C IN Hung to dry Washable at 60 C e Iron at 150 C Mm Dry on clothes hanger Washable at 40 C ex iron at 100 C C Tumble dry normal heat Washable at 30 C ed Don t iron Tumble dry reduced heat d Hand wash A Dry cleaning w
20. titute problems Do not contact the Service Center until the problem has been confirmed PROBLEM Washing machine fails to operate Washing machine cannot be filled with water Machine is draining while being filled Drainage failure Strong vibration while spinning Operation stops before completing wash cycle Operation stops for a period of time Excessive foam in the drum which is spilled to the distribution drawer Automatic adjustment of the washing time Spinning fails CAUSES SOLUTIONS Poor connection to the power supply Check connection to the power supply Power failure Check the power supply The washer door is not properly closed _ Close the washer door properly Machine has not been switched on _ Make sure the machine is switched on The Start Pause button is not pressed _ press the Start Pause button Water tap is not turned on _ Turn on the water tap Water pressure is less than 0 03 Mpa Check water pressure The inlet hose is kinked Check the inlet hose Water supply failure _ Ensure the water supply The program knob is not properly set _ Set the program knob properly The washer door is not properly closed Close the washer door properly The inlet hose filter is blocked Unblock the inlet hose filter The height of the drain hose is below 80 cm _ Install drain hose within 80 100 cm of height The drain hose is in water
Download Pdf Manuals
Related Search