USER MANUAL - Kramer Electronics
Contents
1. Configuration EH RC 13TC Using Your Video Transport Controller When the RC 13TC functions as a standalone wall mounted video transport controller as illustrated in Figure 3 e The RC 13TC is connected directly to the controlled devices see Section 5 1 1 e A 12V DC power supply to the unit is required see Section 5 1 2 e The RC 13TC requires programming 5 1 1 Connecting the RC 13TC as a Standalone Video Transport Controller The RC 13TC can be connected as a standalone video transport controller as illustrated in the example in Figure 3 with connections as described in the following table Your system integrator configures and installs your room controller to suit your requirements This example describes only one possible configuration Connector Connect to GND 12V Power adapter IR1 Blu ray DVD player 1 IR2 Blu ray DVD player 2 PROGRAM USB PC required only for configuring the RC 13TC RS 232 5 1 2 Connecting a Standalone RC 13TC to a Power Supply Display or switcher When the RC 13TC is employed as a standalone room controller it should be connected to the power supply as illustrated in Figure 4 To 12V DC power supply E BLACK RED Figure 4 RC 13TC Standalone Power Supply Connection RC 13TC Using Your Video Transport Controller 5 2 The RC 13TC as an Auxiliary Control Panel When the RC 13TC is used as an auxiliary control panel as illustrated in Figu2. and 20m IR emitter extension cables Specifications are subject to change without notice at http www kramerelectronics com RC 13TC Technical Specifications LIMITED WARRANTY The warranty obligations of Kramer Electronics for this product are limited to the terms set forth below What is Covered This limited warranty covers defects in materials and workmanship in this product What is Not Covered This limited warranty does not cover any damage deterioration or malfunction resulting from any alteration modification improper or unreasonable use or maintenance misuse abuse accident neglect exposure to excess moisture fire improper packing and shipping such claims must be presented to the carrier lightning power surges or other acts of nature This limited warranty does not cover any damage deterioration or malfunction resulting from the installation or removal of this product from any installation any unauthorized tampering with this product any repairs attempted by anyone unauthorized by Kramer Electronics to make such repairs or any other cause which does not relate directly to a defect in materials and or workmanship of this product This limited warranty does not cover cartons equipment enclosures cables or accessories used in conjunction with this product Without limiting any other exclusion herein Kramer Electronics does not warrant that the product covered hereby including without limitation the techn
3. ET DEFAULT Factory Press and hold during power up to erase all Default Reset Button custom programming Note The current LCD text and all button actions are erased RS 232 3 pin Removable For controlling a display switcher AV source or Terminal Block other AV equipment IR Infrared 2 pin Removable Connect to IR emitters see Figure 3 Terminal Blocks 1 and 2 Connect OUT 1 or OUT 2 to IR anode GND to GND cathode PROGRAM USB Connector Connect to a computer to program the unit ID LCD text and button actions using K Config Configuration software 11 Power Supply 2 pin Removable Connect to power supply see Section 5 1 2 Terminal Block Connect GND to GND 12V to 12V 12 FW UPGRADE Switch For the use of Kramer service personnel only RC 13TC Defining the RC 13TC Video Transport Controller 5 Using Your Video Transport Controller This user manual is applicable once the unit is configured and installed by your system integrator therefore the following procedures are not detailed in this manual e Hardware installation e Programming the LCD readout using K Config Configuration software described in the K Config Configuration Guide e Programming the button actions using K Config Configuration software 5 1 The RC 13TC as a Standalone Video Transport Controller PC using during the initial programming stage Blu ray DVD Projector Figure 3 Sample RC 13TC Standalone Video Transport Controller
4. KRAMER ELECTRONICS LTD USER MANUAL MODEL RC 13TC Video Transport Controller P N 2900 000648 Rev 3 Contents Introduction 2 Getting Started 2 1 Achieving the Best Performance 3 Overview 4 Defining the RC 13TC Video Transport Controller 5 Using Your Video Transport Controller 5 1 The RC 13TC as a Standalone Video Transport Controller 5 2 The RC 13TC as an Auxiliary Control Panel 5 3 Operating the RC 13TC Video Transport Controller 6 Grounding the RC 13TC Video Transport Controller 7 Mounting the Faceplate 8 Technical Specifications Figures Figure 1 RC 13TC Video Transport Controller Front Panel Figure 2 RC 13TC Video Transport Controller Rear Panel Figure 3 Sample RC 13TC Standalone Video Transport Controller Configuration Figure 4 RC 13TC Standalone Power Supply Connection Figure 5 RC 13TC Connections when used as part of a K NET System Figure 6 RC 13TC LCD Programmed with Text Figure 7 Grounding Connection Components ODDD R OONN N O COONDOSA Introduction Welcome to Kramer Electronics Since 1981 Kramer Electronics has been providing a world of unique creative and affordable solutions to the vast range of problems that confront the video audio presentation and broadcasting professional on a daily basis In recent years we have redesigned and upgraded most of our line making the best even better Our 1 000 plus different models now appear in 11 groups that ar
5. NTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IF KRAMER ELECTRONICS CANNOT LAWFULLY DISCLAIM OR EXCLUDE IMPLIED WARRANTIES UNDER APPLICABLE LAW THEN ALL IMPLIED WARRANTIES COVERING THIS PRODUCT INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL APPLY TO THIS PRODUCT AS PROVIDED UNDER APPICABLE LAW IF ANY PRODUCT TO WHICH THIS LIMITED WARRANTY APPLIES IS A CONSUMER PRODUCT UNDER THE MAGNUSON MOSS WARRANTY ACT 15 U S C A 2301 ET SEQ OR OTHER APPICABLE LAW THE FOREGOING DISCLAIMER OF IMPLIED WARRANTIES SHALL NOT APPLY TO YOU AND ALL IMPLIED WARRANTIES ON THIS PRODUCT INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR THE PARTICULAR PURPOSE SHALL APPLY AS PROVIDED UNDER APPLICABLE LAW Other Conditions This limited warranty gives you specific legal rights and you may have other rights which vary from country to country or state to state This limited warranty is void if i the label bearing the serial number of this product has been removed or defaced ii the product is not distributed by Kramer Electronics or iii this product is not purchased from an authorized Kramer Electronics reseller If you are unsure whether a reseller is an authorized Kramer Electronics reseller please visit our Web site at www kramerelectronics com or contact a Kramer Electronics office from the list at the end of this document Your rights under this limited warranty are not diminished if you do not complete and re
6. at Kramer Electronics will not do Under This Limited Warranty If this product is returned to Kramer Electronics or the authorized dealer from which it was purchased or any other party authorized to repair Kramer Electronics products this product must be insured during shipment with the insurance and shipping charges prepaid by you If this product is returned uninsured you assume all risks of loss or damage during shipment Kramer Electronics will not be responsible for any costs related to the removal or re installation of this product from or into any installation Kramer Electronics will not be responsible for any costs related to any setting up this product any adjustment of user controls or any programming required for a specific installation of this product How to Obtain a Remedy under this Limited Warranty To obtain a remedy under this limited warranty you must contact either the authorized Kramer Electronics reseller from whom you purchased this product or the Kramer Electronics office nearest you For a list of authorized Kramer Electronics resellers and or Kramer Electronics authorized service providers please visit our web site at www kramerelectronics com or contact the Kramer Electronics office nearest you In order to pursue any remedy under this limited warranty you must possess an original dated receipt as proof of purchase from an authorized Kramer Electronics reseller If this product is returned under this limited warranty a retu
7. e clearly defined by function GROUP 1 Distribution Amplifiers GROUP 2 Switchers and Routers GROUP 3 Control Systems GROUP 4 Format Standards Converters GROUP 5 Range Extenders and Repeaters GROUP 6 Specialty AV Products GROUP 7 Scan Converters and Scalers GROUP 8 Cables and Connectors GROUP 9 Room Connectivity GROUP 10 Accessories and Rack Adapters and GROUP 11 Sierra Products Congratulations on purchasing your Kramer RC 13TC Video Transport Controller which is ideal for use as an e Advanced standalone wall mounted video transport controller When used in this way the unit must be configured as well as supplied with 12V DC power Refer to the separate online K Config Configuration Guide at http www kramerelectronics com e Auxiliary device in a larger Kramer K NET room control setup The package includes the following items e The RC 13TC Video Transport Controller e 3 0 91m USB cable e IR Emitter control cable e Power supply 12V DC e Screwdriver e This user manual The latest Kramer user manuals are available from http www kramerelectronics com e K Config Configuration software C Introduction 2 Getting Started We recommend that you e Unpack the eguipment carefully and save the original box and packaging materials for possible future shipment Review the contents of this user manual e Use Kramer high performance high resolution cables Go to http Awww kramerelectronics co
8. m to check for up to date user manuals application programs and to check if firmware upgrades are available where appropriate This user manual is written for the end user and does not contain details regarding installation and configuration This information can be found in the K Config Configuration Guide available from http www kramerelectronics com 2 1 Achieving the Best Performance To achieve the best performance e Use only good guality connection cables to avoid interference deterioration in signal guality due to poor matching and elevated noise levels often associated with low quality cables e Avoid interference from neighboring electrical appliances that may adversely influence signal quality e Position your Kramer RC 13TC away from moisture excessive sunlight and dust Caution No operator serviceable parts inside the unit Warning Disconnect the power and unplug the unit from the wall before installing Overview This user manual describes the RC 13TC Video Transport Controller The RC 13TC controller interface acts as an all in one remote control panel for several AV sources in any venue such as classrooms boardrooms or auditoriums The RC 13TC streamlines operations by enabling remote transport control of the video source in the room The RC 13TC features Programmable backlit buttons configurable by your system integrator that are able to execute one or multiple commands programmi
9. ng performed by your system integrator A bidirectional RS 232 serial port for control of AV equipment Two K NET ports Two IR control ports Support for firmware upgrade via USB or the K CNET connection when installed as an auxiliary device 4 Defining the RC 13TC Video Transport Controller This section defines the RC 13TC Source E lt gt 7 OOO y OOOOD a gt gt PREVIREW PLAY PAUSE STOP NEXT FWD KRAMER RC 13TC Figure 1 RC 13TC Video Transport Controller Front Panel Feature Function Source Select Button Press to select the AV source Video Transport Control Buttons Use to control the functions of the selected AV source characters on a blue background which usually reflects the selected AV source name g LCD Programmable Readout Programmable 8 character LCD readout with white ji 4 RC 13TC Defining the RC 13TC Video Transport Controller DEFAULT Rx i GND 4 GND qJ B E SERVICE 1 T OUT oum TL GND oi om H 4 te GND aw M dey OT vita KNET 2 J LL KNE Figure 2 RC 13TC Video Transport Controller Rear Panel Feature Function 4 KNET TERM Termination Switch Use to set the K NET bus termination see Section 5 2 2 KNET 4 pin Removable Terminal Connect to a master room controller or to another Blocks 7 and 2 auxiliary device Connect GND to GND B to B Ato A 12V to 12V see Section 5 2 RES
10. ology and or integrated circuit s included in the product will not become obsolete or that such items are or will remain compatible with any other product or technology with which the product may be used How Long Does this Coverage Last Seven years as of this printing please check our Web site for the most current and accurate warranty information Whois Covered Only the original purchaser of this product is covered under this limited warranty This limited warranty is not transferable to subsequent purchasers or owners of this product What Kramer Electronics will do Kramer Electronics will at its sole option provide one of the following three remedies to whatever extent it shall deem necessary to satisfy a proper claim under this limited warranty 1 Elect to repair or facilitate the repair of any defective parts within a reasonable period of time free of any charge for the necessary parts and labor to complete the repair and restore this product to its proper operating condition Kramer Electronics will also pay the shipping costs necessary to return this product once the repair is complete 2 Replace this product with a direct replacement or with a similar product deemed by Kramer Electronics to perform substantially the same function as the original product 3 Issue a refund of the original purchase price less depreciation to be determined based on the age of the product at the time remedy is sought under this limited warranty Wh
11. re 5 e It requires only a K NET connection to another auxiliary device e A power supply unit is not required as the K Net connection carries the power supply Power supplies are sold separately Consult your Kramer dealer for details e No programming of the auxiliary panel is needed e Depending on the setup the device ID may need setting using the K Config application e The RS 232 and IR ports may be used to control devices 5 2 1 Connecting Multiple RC 13TC Devices as System Controllers Connect the RC 13TC devices to the SV 552 as illustrated in Figure 5 LLkNET2_J LKNET1_J RC 13TC K NETID 3 RC 13TC K NETID 2 SV 552 K NET ID 1 OUTPUTS ovi To PROJECTOR rae Mure WP 10V Voor RELAYS IP RS 232 P RSS MR OLTI EEEE GC GVW NICK GR GBA OTG Figure 5 RC 13TC Connections when used as part of a K NET System 5 2 2 Setting the K NET Termination The first and last physical devices on a K NET bus must be terminated in this example devices 1 and 3 EH RC 13TC Using Your Video Transport Controller 5 3 To terminate the RC 13TC e Slide the K NET termination switch down The factory default is down terminated Operating the RC 13TC Video Transport Controller The RC 13TC is delivered with no button functions preprogrammed For the buttons to perform any functions they must be programmed first Once a button is programmed to suit the source or di
12. rn authorization number obtained from Kramer Electronics will be required You may also be directed to an authorized reseller or a person authorized by Kramer Electronics to repair the product If it is decided that this product should be returned directly to Kramer Electronics this product should be properly packed preferably in the original carton for shipping Cartons not bearing a return authorization number will be refused Limitation on Liability THE MAXIMUM LIABILITY OF KRAMER ELECTRONICS UNDER THIS LIMITED WARRANTY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE PAID FOR THE PRODUCT TO THE MAXIMUM EXTENT PERMITTED BY LAW KRAMER ELECTRONICS IS NOT RESPONSIBLE FOR DIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR CONDITION OR UNDER ANY OTHER LEGAL THEORY Some countries districts or states do not allow the exclusion or limitation of relief special incidental consequential or indirect damages or the limitation of liability to specified amounts so the above limitations or exclusions may not apply to you Exclusive Remedy TO THE MAXIMUM EXTENT PERMITTED BY LAW THIS LIMITED WARRANTY AND THE REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES REMEDIES AND CONDITIONS WHETHER ORAL OR WRITTEN EXPRESS OR IMPLIED TO THE MAXIMUM EXTENT PERMITTED BY LAW KRAMER ELECTRONICS SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION WARRANTIES OF MERCHA
13. splay that is connected the other button functions are related to the specific device and are context sensitive that is the function of a button depends on the specific characteristics of the source or display In the example illustrated in Figure 6 the RC 13TC LCD has been programmed with text and the buttons have been programmed by your system integrator to perform the functions that are relevant to the sources Individual buttons can be programmed with one or more actions called a macro This is only one example among numerous possibilities as the LCD and each button can be programmed as required When pressing a button that has been programmed with a macro each action is performed sequentially and it may take some time until the macro terminates PREVIREW PLAY PAUSE STOP NEXTIFD KRAMER RC 13TC Figure 6 RC 13TC LCD Programmed with Text Grounding the RC 13TC Video Transport Controller We recommend that you ground the RC 13TC The grounding screw is used to earth the chassis of the unit to the building ground preventing static electricity from impacting the performance of the unit Figure 7 defines the grounding screw components Component Description 1 M3x6 screw 2 M3 Toothed Lock Washer M3 Ring Tongue Terminal Figure 7 Grounding Connection Components To ground the RC 13TC 1 Connect the ring tongue terminal to the building grounding point wire we recommend that you use a green yello
14. turn the product registration form or complete and submit the online product registration form Kramer Electronics thanks you for purchasing a Kramer Electronics product We hope it will give you years of satisfaction For the latest information on our products and a list of Kramer distributors visit our Web site where updates to this user manual may be found We welcome your questions comments and feedback Web site www kramerelectronics com KRAMER E mail info kramerel com SAFETY WARNING Disconnect the unit from the power m supply before opening and servicing P N 2900 000648 Rev 3
15. w AWG 18 0 82mm2 wire crimped with a proper hand tool 2 Insert the M3x6 screw through the toothed lock washers and the tongue terminal in the order shown above 3 Insert the M3x6 screw with the two toothed lock washers and ring tongue terminal into the grounding screw hole and tighten the screw RC 13TC Grounding the RC 13TC Video Transport Controller 7 Mounting the Faceplate To mount the faceplate 1 Remove the protective foil from the outside of the LCD acrylic window 2 Position the faceplate on the RC 13TC so that the four screw mounting holes are aligned 3 Insert the four M3x4mm mounting screws and tighten them with a screwdriver RC 13TC Mounting the Faceplate 8 Technical Specifications 2 K NET on 4 pin removable terminal blocks 1 USB port 1 12V DC power input on 2 pin removable terminal block 1 RS 232 port on 3 pin removable terminal block OUTPUTS 2 IR control on 2 pin removable terminal blocks POWER SOURCE 12V DC 60mA OPERATING TEMPERATURE 0 to 55 C 32 to 131 F STORAGE TEMPERATURE 45 to 72 C 49 to 162 F HUMIDITY 10 to 90 RHL non condensing DIMENSIONS 11 4cm x 2 3cm x 11 4cm 4 5 x 0 91 x 4 5 W D H WEIGHT 0 3kg 0 66lbs approx ACCESSORIES USB cable 3 0 91m P N C UA MUB 3 screwdriver power supply IR emitter control cable P N C A35 IRE 10 Windows based Kramer control software four M3x4mm flat head screws OPTIONS 15m
Download Pdf Manuals
Related Search