User Manual - Stemmer Imaging
Contents
1. 16 Jo P XD1 Positive LVDS Output Cameralink Data DI 17 Jo P XD2 Positive LVDS Output Cameralink Data D 18 JO P XCLK Positive LVDS Output CameraLink clock 19 Jo P xD3 TPositive LVDS Output Cameralink Data D3 20 N SERTOCAM Negative LVDS Input Serial Communication tothe camera 21 JO P SERTOFG Positive LVDS Output Serial Communication from the camera 22 P CCi Positive LVDS Input external Trigger signal EXSYNC 23 NCC2 Negative LVDS Input not used S 24 P CC3 Positive LVDS Input serial clock Fast configuration interface 25 N CC4 Negative LVDS Input data Fast configuration interface Shield 4 2 Pin Assignments for the Socket of the Voltage Supply Connector mm uo mame oem 5 V voltage supply Connector socket Nr 09 0408 90 03 for the voltage supply REV 1 1 Page 7 26 photon focus 5 Basic Operation and Features Note The high speed interface can be accessed by the microEnablelll fast configurationframe grabber In this case not all functions described in this section are available or are replaced by default values see ME FC MV D1024 TrackCam User Manual 5 1 Configuration Interfaces The MV D1024 TrackCam can be programmed via a e High speed interface up to 40 MBaud that lets you modify important camera configuration parameters wi2. e EN61000 6 2 e 2001 e EN61000 6 3 e 2001 e EN61000 4 2 e 1995 e EN61000 4 3 e 1996 e EN61000 4 4 e 1995 e EN61000 4 6 e 1996 e EN55022 e 1994 This declaration becomes void in case of any changes on the product without written authorization by Photonfocus REV 1 1 Page 21 26 photon fec us 8 3 Package Content The package includes the following MV D1024 TrackCam User Manual e Camera e Lens protective cap e enclosing note e Power supply connector Photonfocus reserves itself the right to change the content at any time without indication of reasons 8 4 Accessories For the camera MV D1024 TrackCam are several accessories available For detailed information about the listed parts refer to the Photonfocus Web page www photonfocus com e CLB 26 Digipeater CameraLink Repeater for extended cable length e CameraLink cables e Power supply REV 1 1 Page 22 26 photon foc us 9 Service Information MV D1024 TrackCam User Manual For product enquiries and quotations please contact one of our distributors in your area A list of distributors can be found on our web site www photonfocus com Product information documentation and software updates can also be found on our web site 9 1 Guarantee Conditions 9 1 1 Guarantee Claims The manufacturer alone reserves the right to recognize guarantee claims The guarantee will be rendered null and void in the event of unauthorized manipulation
3. Page 4 26 photon fec us 2 How To Get Started 1 MV D1024 TrackCam User Manual Remove the camera from its packing and ensure that it is complete and undamaged If any damage has occurred during transport please contact the transport company and your distributor immediately Connect the camera to the microEnablelll fast configuration frame grabber with a suitable CameraLinkO cable Important Note Only cables can be used where each wire pair is shielded Thus the following Phontonfocus cables cannot be used Part no 704020 052 and 704020 102 Warning Do not connect or disconnect connections while camera power is on The camera is delivered with a 3 pole power plug Ensuring that the maximum operating voltage is not exceeded connect the camera to a suitable power supply 5V DC 10 To use the camera in the Fast Configuration mode please read the getting started section of the Silicon Software Fast Configuration manual ME_FC Additional functions can be programmed with the PFRemote tool see chapter PFRemote or with Photonfocus pflib delivered with PFRemote tool REV 1 1 Page 5 26 photon focus MV D1024 TrackCam User Manual 3 Technical Data Technical Data for the MV D1024 TrackCam Number of pixels Linear or LinLog adjustable Spectral range 400 nm 900 nm see Fig 1 Maximum frame rate 75 fps O Tin 10 us High Speed configuration interface Synchronous transmission lt 40MBaud 1 Sta
4. frame camera control with up to 40 Mbit s instead of the usual 9 6 kbit s The camera provides an exceptionally high dynamic range of up to 120dB at a resolution of 1024 x 1024 pixels and a frame rate of up to 75 full images per second It is built around a CMOS image sensor that has been specially developed by Photonfocus The principal advantages of the Photonfocus CMOS technology are 1 Low power consumption at high speeds 2 Resistance to blooming smear and image lags 3 Extremely high image contrast achieved by LinLog technology With the fast configuration interface in combination with ROI and LinLog technology Photonfocus offers an absolutely unique product designed for e Tracking of fast moving objects e Simultaneous inspection of different regions e Shot to shot definition of ROI exposure time and LinLog settings e The MV D1024 TrackCam is targeted to e Industrial welding process welding inspection PCB inspection e Sport movement analysis object tracking e Research and development The compact size of only 55 x 55 x 46 mm makes the MV D1024 TrackCam the perfect solution for applications in which space is at a premium With the digital camera series Photonfocus has proven that the image quality of modern CMOS sensors is now appropriate for a wide range of applications Photonfocus is ISO 9001 certified All products are produced with the latest techniques in order to ensure the highest degree of qual
5. increased to avoid image artefacts The LineHopping attribute defines the line readout stepping For example a number of 2 skips all odd lines 6 6 MROI Mask Mode When activated the MROI mode applies a maximum number of 16 masks to the current window of interest A mask is defined as a range of scan lines which are skipped and not read out which further speeds up the image acquisition Note that mask windows may not overlap and are not checked for sanity The parent window Main WOI must include the first mask but may exclude trailing unused masks A mask is defined by its Y start value and the height H These are entered analogous to the main ROI REV 1 1 Page 14 26 photon focus As an example the greyed out areas on the zebra 5 denote the mask areas The read out result in the frame grabber is displayed on the right the black lines are just displayed to better visualize the seams MV D1024 TrackCam User Manual Picture with 4 masks Resulting 5 image stripes 6 7 Characteristic Curves And Amplification High Gain Resolution LUT slot Edit LUT REV 1 1 MY D1024 28 CL 10 siso Exposure Trigger Window Characteristics LinLog Skim High Gain Resol mode Lur mode LUT Slot o Reset to Defaults Store in EEPROM Factory Reset Edit LUT Framerate fps fi 3 53 Toggle High Gain amplification Choose camera ADC resolution bit depth LUT or LFSR Rando
6. sssssssssss I Ie heme nnn 8 5 6 Status Indicator oth Oe ehe nE AEE ates etuer SEMANAS A ee DERE NR pES 9 6 PFRemote uuuiuuseuasaneansanesnsaneonoonooanoansaneaneanaana ana ana ane ana ana a aan nana nana 10 6 1 About PFRemote Software ii insistente eee teeta eee eee 10 6 1 1 Getting The Software eme eese hehe eese sehn e testen nennen 10 6 1 2 Installing The Software isssssssssssssssss e emen emen nennen 10 6 1 3 Supported Operating Systems csssssssssssssssss eee emen 10 6 2 Camera Initialization 0 eem m m s em hehehe nennen nnns 11 6 3 Stored Camera Configuration csse ese eene eene 11 6 4 Exposure and Triggermodes ssssssssssssssssse eme eese meses nenne 12 6 4 1 Advanced Triggering Modes cece cece eee eee nee teeta teeta eae 13 6 5 Window Of Interest xs iiec ge eee n damn eee gees e eee ERRA E Re EX ii 14 6 6 MROI Mask MOQOG uicit orte cule CALA cade dyed Sa SAIDA henna E end 14 6 7 Characteristic Curves And Amplification ciiii iss mm 15 6 8 LUT Editor Look up Table ci serraria rear 16 6 9 Linbog and SKIMMING coro coro e atin nes Senda lana dese quta a o eae edu da 17 6 10 Calibration 2 0 III eme E DE rear ra netten nennen 18 7 Mechanical Dimensions eeeeieseesesesssseu aenea neun an annua uum a naa n uana 20 8 Important Notes seesseseeuesus
7. ality is restricted with some of these modes See PFRemote Help for more information OK Slave mode External Master clock synchronization via the MCLK wires Sync pulses high This is the default If deselected the trigger signals must be active inverted and the schemes below must be thought inverse as well Ext Trigger with On sync pulse start the programmed exposure slider programmed ExposureTime begins exposure Ext Trigger Not available in TrackCam exposure start Exp stop Combined The length of the ExSync pulse determines the exposure time Trigger Exposure REV 1 1 Page 13 26 photon fec us 6 5 Window Of Interest The Window Of Interest WOI also called region of interest is defined as a rectangle x y w h where MV D1024 TrackCam User Manual x X coordinate of upper left corner starting with O y Y coordinate of upper left corner starting with O w Width of window h Height of window The rows and columns are counted beginning at 0 i e the last row and the last column have the address 1023 x Exposure Trigger Window Characteristics LinLog Skim Fleset to Defauks REA D Use MasksmRoN Store in EEPROM x o pt Ww 1024 Factory Reset Set x o 53 1353 LineHopping E E Framerate fps Please note that certain restrictions apply to the start and stop value of horizontal direction X If this is not the case the LinePause value is automatically
8. d be noted MV D1024 TrackCam User Manual The apparatus may only be used for the purpose described The apparatus is only suitable for indoor use Protect it from moisture and heat The permitted operating temperature range is 0 C to 60 C Never attempt repairs yourself Repairs may only be carried out by trained expert staff Moreover every piece of equipment is tested before delivery and has a guarantee symbol attached For cleaning purpose use only a dry soft cloth Never use water or chemicals REV 1 1 Page 24 26 photon fec us 10 Literature ANOO1 Application note ANOO1 LinLog 2 found on http www photonfocus com html eng support applicationNotes php ANO04 Application note ANOO4 Reset Strategies found on http www photonfocus com html eng support applicationNotes php FGLIST Frame grabber compatibility list http www photonfocus com html eng support framegrabbers php ME FC User Manual for microEnablelll fast configuration frame grabber Silicon Software http www siliconsoftware de MV D1024 TrackCam User Manual REV 1 1 Page 25 26 photon focus 11 Document History MV D1024 TrackCam User Manual Document revisions REV Changes Date 1 0 First revision 2004 05 17 1 1 Added note that mode ext trigger exposure start Exp stop is not available 2004 07 07 Slight modifications in Getting started chapter REV 1 1 Page 26 26
9. his case the offset voltage may need to be adjusted Note that the skimming effect is reverse to the voltage i e higher voltage means less skimming Note that with too low skimming voltage settings the image may no longer look good Handle with care REV 1 1 Page 19 26 photon focus 7 Mechanical Dimensions MV D1024 TrackCam User Manual 4x 061 REV 1 1 Page 20 26 photon focus 8 Important Notes MV D1024 TrackCam User Manual Photonfocus reserves the right to make changes to its products without notice Photonfocus products are neither intended nor certified for use in life support systems or in other critical systems The use of Photonfocus products in such applications is forbidden Photonfocus LinLog LinLog2 and CameraLink are registered trademarks in Switzerland and in other countries 8 1 Storage and Transport During storage and transport the camera should be protected against vibration shock moisture and dust The original packing protects the camera adequately from vibration and shock during storage and transport Please either retain this packing for possible later use or dispose of it according to local regulations 8 2 Declaration of Conformity We the manufacturer Photonfocus AG Bahnhofplatz 10 CH 8853 Lachen Switzerland Europe hereby declare that the products of the camera MV D1024 TrackCam released in 2004 conforms to the following standards or other normative documents
10. ich uses the CameraLinkO RS232 interface Note To use the high speed configuration interface you need the microEnablelll fast configuration frame grabber from Silicon Software Please refer to the frame grabber manual ME FC In this case the camera is programmed by the frame grabber software However there are functions that can only be programmed by PFRemote software Warning Do not use PFRemote while using the high speed interface 6 1 1 Getting The Software The latest version of the PFRemote software can be downloaded at http www photonfocus com html eng support software php 6 1 2 Installing The Software Run the PFRemote SDK executable to start an installation wizard which guides you through the installation Framegrabber selection Select Silicon Software menable3 from the drop down list Setup PFRemote IMPORTANT Select Framegrabber Type Which frame grabber communication modules should be installed Please select your grabber type in the choice below If your grabber has a looped in R5232 com port or uses a virtual com port windows driver accessible by device COM3 or higher choose the first option Please note that only ONE framegrabber is supported at a time Automatic runtime support will be implemented in a future version Silicon Software menable3 PFRemote exe and required DLLs O SDK source examples and Documentation PDF 1 3 MB C HTML SDK documentation 0 6 MB Q Serial Co
11. ion parameters such as LinLog and Skimming values can not be read out therefore the displayed values might not be correct To make sure the display is synchronized you have to reset the camera manually via the Reset to Defaults button REV 1 1 Page 11 26 photon fec us MV D1024 TrackCam User Manual 6 4 Exposure and Triggermodes M D1024 80 CL 8 sisol X Exposure Trigger window Characteristics LinLog Skim Reset to Defaults Trigge C Free Running Extern Sync ring Advanced Store in EEPROM Constant FrameRate Line Pause E Factory Reset ExposureTime ms Lr 1413 FE Free Running Extern Sync Advanced Constant FrameRate LinePause Exposure Time Frame Time Frame Rate melime ns z094 Framerate fps Free Running Mode the camera generates consecutive frames whose rate is determined by the set exposure time resp frame time External synchronization through EXSYNC signal Set advanced triggering modes see below For free running mode only If this flag is set the frame rate is determined by the frame time which can be set below Otherwise the camera will immediately deliver another frame after the sensor exposure This is the horizontal blank time in number of pixel clock cycles Some frame grabbers require larger numbers than the standard default 8 fastest If your frame grabber displays artefacts increase Li
12. it update of the settings Quick steps for LinLog adjustment refer to application note ANOO1 Choose LinLog Control LinLog2 Default stands for the default setting which is only well defined if the camera is reset since LinLog values can not be read back The LinLog setting makes only use of the LL1 parameter see below Set the LinLog high compression LL1 to a value such that your maximum intensity spot in the image resolves well or just starts to show bright gray Set the low compression LL2 to a value less than LL1 Fine tune the COMP fraction value around small values in the range of 0 100 to achieve an image with optimum dynamical resolution in high intensity ranges This may require some iteration through the settings The Skimming mode allows to brighten up darker areas non linear REV 1 1 Page 17 26 photon fec us 6 10 Calibration Normally the camera does not need to be calibrated as this is done after manufacture In some cases recalibration or detuning by purpose might be desired MV D1024 TrackCam User Manual The calibration dialog is called via the Menu Camera Calibration Voltage changes can always be undone by restoring the factory defaults via the configuration dialog M D1024 Calibration x Offset LowGain Volts fi e3 Hex Oxa900 Offset HighGain Volts 2 36 Hex oxta80 High Gain VSkim Volts 2 39 Hex OxtcB0 Skim Hex 0 4100 D e Channe
13. ity and to satisfy the requirements of our customers REV 1 1 Page 3 26 photon fec us 1 1 The MV D1024 TrackCam The MV D1024 TrackCam is a high end CMOS megapixel camera with global shutter It has a fast configuration interface that lets you modify the most important camera configuration parameters at speeds up to 40 MBaud MV D1024 TrackCam User Manual The camera includes the following features e CMOS Progressive scan global shutter monochrome e Upto 75 fps full frame rate e LinLog Pixel with up to 120 dB dynamic range e CameraLinkO Interface e Internal Lookup Table e 8 Bit digital resolution e Region of interest ROI e Skimming Mode in which small signal gain of a pixel is increased e Programmable via a high speed Configuration Interface or an RS 232 serial port e Designed for frame grabber microEnablelll fast configuration by Silicon Software e C Mount objective mount 1 2 Frame Grabber The MV D1024 TrackCam is designed to be used with the microEnablelll fast configuration frame grabber from Silicon Software This special frame grabber version accesses the MV D1024 TrackCam via the high speed configuration interface The camera is controlled and programmed with the frame grabber software However it can be run with any Photonfocus compliant frame grabber see FGLIST in Literature In this case the camera can be programmed with the tool PFRemote see chapter 6 but fast configuration is not possible REV 1 1
14. l so that small signals are amplified significantly more than large signals e LinLog mode In situations involving high intrascene contrast compression of the upper grey level region can be achieved with the LinLog Technology At low intensities each pixel shows a linear response At high intensities the response changes to logarithmic compression The transition region between linear and logarithmic response can be smoothly adjusted and is continuously differentiable Skimming and LinLog can be combined to achieve maximum control of the sensor output Please refer to application note ANOO1 for detailed information on the setting of LinLogTM REV 1 1 Page 8 26 photon fec us 5 6 Status Indicator A two color LED on the rear of the camera indicate the camera status to the user In normal operation the LED lights green when an image is being produced At low frame rates a flickering can be observed that changes to a continuous light at high frame rates Since the light intensity is dependent on the relation between exposure time and read out time the light from the LED can practically disappear when using small ROI and long exposure times A red LED indicates that serial communication on the RS232 interface is active MV D1024 TrackCam User Manual REV 1 1 Page 9 26 photon focus 6 PFRemote MV D1024 TrackCam User Manual 6 1 About PFRemote Software The MV D1024 TrackCam can be programmed with the tool PFRemote wh
15. line Delete Depth 3 512 bytes Further LUT tables can be downloaded Receive from the camera and stored to disk Depending on the curve mode the curve parameters are either Spline mode Saved in a LUT spline set by entering the setting name in the LUT spline sets choice and pressing Save Free mode Saved in a readable ascii hex code dump file If in spline mode a set simply can be chosen from the drop down choice Entries can be erased with the Delete button REV 1 1 Page 16 26 photon foc us 6 9 LinLog and Skimming MV D1024 TrackCam User Manual The LinLog feature provides a semi logarithmic adjustable behaviour of the camera characteristics so that extreme white intensities can be monitored without saturation while keeping optimum resolution on dark areas M D1024 80 CL 8 x Reset to Defaults Store in EEPROM Factory Reset Exposure Trigger Window Characteristics LinLog Skim LinLog Control Defaut LL1 1 2 COME Skim Skimming Framerate fps 23 72 1 Note that the LinLog state might not be known to the application after opening the camera configuration dialog Therefore the LinLog Control choice displays Default Use this choice to turn LinLog off or explicitely on or reset the camera Reset to Defaults to update the current default settings The Skimming slider is only accessible after a explic
16. ls volts 0 35 c to e 1 k 4 k 1 k 1 k 1 zL m i Channel Volts 2 42 Restore from EEPROM Store in EEPROM Entries which are greyed out can not be changed by the user Offset LowGain The black level offset voltage for the LowGain setting i e HighGain off Offset HighGain Black level offset voltage for HighGain setting For calibration you need a frame grabber software with real time histogram functionality It is also possible to do the calibration by looking at the minimal gray value of the grabbed image The standard procedure 1 Make sure that the sensor is receiving no more light by either covering the C mount with the usually included protection cap or by closing the iris of the C mount lens Set camera exposure time to minimum 2 Make sure that HighGain is tumed off and change the LowGain offset voltage such that the black level peak displays as in the left image below 3 Same for HighGain Activate HighGain via the check box and change the offset such that the black level distribution looks like in the image on the right 4 Store the values in the EEPROM via the Store in EEPROM button REV 1 1 Page 18 26 photon foc us MV D1024 TrackCam User Manual 0 127 255 eo 127 LowGain mode histogram 255 HighGain mode histogram The Skimming is normally changed in the LinLog panel but can be changed here as well if the camera is run in skimming mode by default In t
17. m test pattern Switch to LUT number n Open LUT editor window see below Page 15 26 photon foc us 6 8 LUT Editor Look up Table The LUT editor allows to create look up tables which digitally re map intensity values to other values The value conversion is directly done on the camera whereas an input range 0 n n according to camera bit depth is mapped to a output range of 0 255 MV D1024 TrackCam User Manual The LUT editor displays either spline curves or free points whereas the free point display is not very accurate since the input values can cover a greater range than the canvas display s size in x The input range is O 511 Editing of the LUT curve happens by dragging the control points in Spline mode or simply painting on the window in Free mode Once the curve is ready to be uploaded you should first test it in the camera s RAM Default Pressing Send uploads the LUT data to the camera which can take some time depending on the frame grabber dependant implementation of the serial communication If LUT mode is not enabled it is automatically turned on The LUT finally can be stored in one of the m available EEPROM slots of the camera by selecting the destination with the chooser right next to the Send button Configure LUT X m Camera LUT control LUT editor RAM e Receive LUT spline sets default Load from file m Curve type C Free File Save Sp
18. mechanical damage or damage arising from inappropriate use or from mechanical or electrical modifications especially soldering The guarantee will also be invalidated if the apparatus is used for purposes for which it was not designed if it is incorrectly connected or if it is not used according to the operating instructions Guarantee work can only be assured and carried out by the manufacturer 9 1 2 Repair Time Repair time will normally be a maximum of 10 working days for repairs to a device for which a legitimate guarantee claim is made 9 1 3 Claims for Damages Claims for damages of all kinds especially those arising from use are excluded Liability is limited in all cases to the value of our product 9 1 4 In Case of Damage If the equipment is defective return it in the original packing and with a copy of the receipt to the following address Photonfocus AG Bahnhofplatz 10 CH 8853 Lachen Important Include a written description of the fault as well as your full postal address The equipment will be forwarded in your name to the service department and in the event of a legitimate guarantee claim returned to you without freight charges REV 1 1 Page 23 26 photon foc us 9 1 5 Safety Hints The apparatus conforms with approved electro magnetic standards Opening the apparatus is not permitted Furthermore all guarantee claims will be invalidated by inappropriate use In all circumstances the following shoul
19. mmunication DLL D 1 MB 9 SiSo Cameralink Communication DLLs 0 1 MB O Generic CameraLink support files 0 1 MB Can M Current selection requires at least 7 5 MB of disk space lt Back Cancel 6 1 3 Supported Operating Systems e Windows 2000 Windows XP REV 1 1 Page 10 26 photon foc us 6 2 Camera Initialization On start PFRemote displays a list of available communication ports see figure below MV D1024 TrackCam User Manual Double click on sisoO if your camera is connected to the input A of the Silicon Software framegrabber double click on sisol if your camera is connected to the input B gt PFRemote v0 62 Pil xl Camera Tools Help Ports sisol siso2 siso3 siso PARITY zl Status OK Once the camera has successfully been opened the camera type is displayed Further options appear on right click on the camera entry Info Shows some camera information Reset Resets the camera Close Closes camera and frees communication port 6 3 Stored Camera Configuration This section describes the buttons that appear on the right hand side of the PFRemote window please see also application note ANO04 Reset to Resets the camera and re reads default EEPROM values into the Defaults configuration dialog box Store in EEPROM Store current settings in EEPROM as boot up values Factory Reset Recover factory settings from EEPROM This can take some time Please note Some configurat
20. nePause Exposure time in milliseconds The slider allows to choose a value within the camera s possible range in a nonlinear way Note that the frame time slider may be adjusted if the chosen exposure time requires so read below If Constant FrameRate is set the frame rate is determined by the given frame time in milliseconds Note that if this time is less than the exposure time the Exposure Time slider will be adjusted The calculated frame rate in frames per second fps The frame rate display is updated whenever a relevant value is changed This value can not be edited use frame rate slider and Constant FrameRate mode for precise frame rate control REV 1 1 Page 12 26 photon focus 6 4 1 Advanced Triggering Modes MV D1024 TrackCam User Manual Important There are restrictions on the LinLog functionality with some triggering modes except Ext Trigger with programmed exposure In all other cases the COMP value must be set to 0 0 in order to have LinLog work correctly Other values may show no effect Extended Triggering Modes f x Slave mode external Master clock Sync pulses high active Ext Trigger with programmed exposure ExSync I t Exposure E C Ext Trigger exposure start Exp stop C Combined Trigger Exposure ExSync I ExSync I X Exposure Exposure The blue bar denotes the effective shutter exposure with a delay of one pixel clock cycle Please note that the LinLog function
21. photon focus MV D1024 TrackCam User Manual REV 1 1 CAMERA PHOTONFOCUS AG Little Bahnhofstrasse 10 8853 Lachen Phone 4155451000 Fax 41554510001 www photonfocus com O 2004 PHOTONFOCUS photon focus MV D1024 TrackCam User Manual Index 1 lnc nier 3 1 1 The MV DIO24 TrackGam dut ete ette etn S te ex eom A A E eA ex ie b nri 4 1 2 Frame Grabber oec earn tek rey te oben delved ear alto Ce a o pA Er ere EE EXER 4 2 How To Get Started eeseeeessesesseseasenuanunua auia uua u nnnm 5 3 Technical Data cccccccececeeceeeeeeeeeeeeeeeeeueeeeeaeeeuaeeaeaeeauaeeaeaeuaueeauesuassgeauseuansgeass 6 4 Camera Interface issis a a a a a a a 7 4 1 Pin Assignments for the MDR26 Socket of the CameraLink Interface 7 4 2 Pin Assignments for the Socket of the Voltage Supply Connector 7 5 Basic Operation and Features uuuuuuasaneaeansasansasansanananeansanananeanaanaas 8 5 1 Configuration nterf ces co iet tee metr ee tit HER ie spi Ue Cr dia Diga cR bur Kid 8 5 2 Exposure Control erret retenir raten Dean ala ni aa cb a dede xS 8 5 3 Global Sh tter simsii resisa role Ded An eae pace PU gg ee E piece ne Da tae eden 8 5 4 Region of Interest cete etae ot eR e fuer eve teta tera bee Da Tes id oe oou eae a EO Der git 8 5 5 LinLog and Skimming Mode
22. rt bit 1 Stop bit no Parity bit 55 mm B x 55 mm W x 50 mm H 200g Approved see chapter 8 2 MV D1024 50 QE Diode QE Pixel incl Fill 30 Factor Quantum Eficiency 95 I eo 10 0 350 450 550 650 750 850 950 1050 Wavelength nm Fig 1 Quantum efficiency as function of wavelength REV 1 1 Page 6 26 photon focus MV D1024 TrackCam User Manual 4 Camera Interface The MV D1024 TrackCam is equipped with a CameraLink interface in the base configuration 4 1 Pin Assignments for the MDR26 Socket of the CameraLink I nterface mro meme oem TT 2 Jo NXDO Negative LVDS Output Cameralink Data DO 3 Jo nxDi Negative LVDS Output CameralinkDataD1 4 Jo N xD2 Negative LVDS Output Cameralink DataD2 5 o InNxclk Negative LVDS Output CameraLink Clock 6 o NXD3 j NegativelVDS Output Cameralink DataD3 7 PSERTOCAM Positive LVDS Input Serial Communication to the camera 8 O N SERTOFG Negative LVDS Output Serial Communication from the camera 9 NCCI Negative LVDS Input External Trigger signal EXSYNC 10 P CC2 Positive LVDS Output not used 11 N cc3 Negative LVDS Input serial clock Fast configuration interface 12 P CC4 Positive LVDS Input data Fast configuration interface 15 Jo P XDO Positive LVDS Output Cameralink Data DO
23. sussunuua uuu RA RR ARRA RR RRRRRRARRRRRRRRRRRRRSuRR RAS uu Ran 21 8 1 Storage and Transport otio ga tepore dede Sete P Dana c oe dug 21 8 2 Declaration of Conformity sra eese senes 21 8 3 Package Content ssa oie que da eos Ras N O Cara a a a ERRA SL 22 8 4 ACCeSSOFIOS ied edet Di pres a Susan day esi da pa ER Ea re IER dec Eu 22 9 Service Information eseeeeseeeeseseseunanunna unma unu a uuu u uua u Eana 23 9 1 Guarantee Conditions csssssssssssssssssss sese seen ee esses ene nennen nennen 23 9 1 1 Guarantee Clalms i ice Lue ix ode teed uoi ia Peladas ce ERR aa OPE ie ada 23 9 12 Repair IIT MT m 23 9 1 3 Claims for Damages sssssssssssssssseses e seem me mense n e enne eene nnns 23 9 1 4 ln Case of Damage ette ce tt tec deat eo pte dace Ia Hate aaa taa 23 ARS CMES Iadilccbc e 24 10 Literature eesseeeseieeieseuesunanunuuuuuasu uuu aa ku sa Ru aa Ru adu adu adu asus 25 11 Document History eeseseeeeseesesenhnanunehn annua nuu u nau u nau uana u ununi nnn 26 REV 1 1 Page 2 26 photon foc us MV D1024 TrackCam User Manual 1 Introduction High speed megapixel CMOS camera for fast tracking applications The MV D1024 TrackCam from Photonfocus is aimed at demanding applications in fast image processing The highlight of this camera is the fast configuration interface This makes it possible to use a frame to
24. th the maximum frame rate Note this interface is designed for the microEnablelll fast configuration frame grabber e ARS232 interface working at 9600 Baud included in CameraLinkO interface 5 2 Exposure Control Note When using the high speed interface exposure is controlled by the microEnablelll fast configuration frame grabber Exposure can be controlled by applying external synchronisation signals see section 6 4 A free run mode is also available 5 3 Global Shutter The sensor used in the MV D1024 TrackCam uses a global shutter i e all pixels are exposed at exactly the same time 5 4 Region of Interest With the MV D1024 TrackCam camera it is possible to increase the image data rate by reading out only a part of the pixel matrix The user can define a region of interest ROI within the sensor to be transmitted to the frame grabber and thus higher frame rates can be achieved 5 5 LinLog and Skimming Mode The LinLog CMOS image sensor from Photonfocus employed in the MV D1024 TrackCam allows the user to adapt the characteristics of the sensor to the requirements of the application e Linear mode For normal applications that do not require high contrast the sensor can be operated in linear mode e Skimming mode For applications having short exposure times and low illumination intensity it is advisable to activate skim mode in which a non linear amplification similar to a gamma correction occurs in the pixe
Download Pdf Manuals
Related Search