USER MANUAL - Hoover Service
Contents
1. cleaner housing Hold the brush assembly and stretch the belt until brush mountings slot down into the cleaner housing Rotate the brush to ensure free movement of the belt Replace opposite Refit sole plate opposite secure with screws If cleaning tools were in use check cleaning tool Next check hose handgrip Turn the cleaner ON and stretch the hose to its full length Check that the brushes A are free of debris and can rotate Check for a blockage in the hose socket User checklist If your cleaner is not working properly run through the following checklist 1 ls there a working electricity supply to the cleaner Check with another electrical product 2 Is the dust container full or choked with fine dust To empty the dust container sec the instructions on page 5 6 3 Is the hose blocked To clear a blockage see the instructions on page 6 4 Is there a blockage in the cleaner base To clear a blockage see the instructions on page 6 5 Are the filters blocked To clear the fitters see the instructions on page 5 6 Are the brushes rotating correctly To check the brushes see the instructions on page 6 7 Has the cleaner overheated If so it will take about 45 minutes to reset itself If there is any doubt call the Hoover Service Office for advice They may be able to assist you over the telephone A service charge will be made if the cleaner is exa2. USER MANUAL Ess IMPORTANT SAFETY REMINDERS This appliance should only be used for domestic cleaning as described in this user guide Please ensure that this guide is fully understood before operating the appliance Do not leave the appliance plugged in Always switch off and remove the plug from the socket after use or before cleaning the appliance or any maintenance task This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Children shall not play with the appliance Cleaning and user maintenance shall not be made by children without supervision If the power cord is damaged stop using the appliance immediately To avoid a safety hazard an authorised Hoover service engineer must replace the power cord Keep hands feet loose clothing and hair away from rotating brushes Use only attachments consumables or spares recommended or supplied by Hoover When using cleaning tools ensure that the appliance is kept in the upright parked position This will avoid possible damage to the carpet or floor covering When cleaning stairs do not position the appliance above you Static electricity some carpets can cause a small build up of static electricity Any static disc
3. The bill of sale or receipt must be produced when making any claim under the terms of this guarantee Subject to change without notice A i Y GENERATION FUTURE Hoover Limited Pentrebach Merthyr Tydfil Mid Glamorgan CF48 4TU HOOVER CUSTOMER HELPINE 03444 995599 2015 48017172
4. body Nc 2 Ny 2 Insert the handle into the main body of the cleaner 1 Plug cord into an electrical outlet 2 Press the on off switch to operate cleaner 3 Insert the screw through the handle and into the main body tighten securely CLEANER RELEASE om 4 Place the crevice tool dusting brush into the tool holder Unlock the cleaner by placing on the foot on the hood and leaning the handle backward For cleaning under low furniture simply lower handle to floor MENA CLEANING TOOLS IMPORTANT When using cleaning tools the cleaner must be kept To remove the dust container from the cleaner press the bin release button e in the upright position particularly when cleaning stairs To Detach the cleaning Attach crevice tool to the hose end connector hose rotate the hose end anti clockwise and pull upwards To use the dusting brush function simply press the button and slide to the end of crevice tool Hold the container over a bin and push the easy open button placed at the rear of the dust container Fit the Per Hair 8 Allergen Remover er All accessories can fit on the end of the tube The dust container door will open and you can empty with no contact with dust CLEANING THE STAIRS N IT IS DANGEROUS TO PLACE THE CLEANER ABOVE X wee IMPORTANT Do not fill above the MAX level YS mark shown on the bin YOU WHEN CLEANING STAIRS 35
5. 0 S ALWAYS work with the cleaner below you Ensure it ah is positioned up against the bottom step 4 MAX Certain models only ale MAINTAINING THE DUST CONTAINER AND FILTERS PERIODIC MAINTENANCE IS REQUIRED TO MAINTAIN OPTIMUM PERFORMANCE Remove the dust container as described on the previous page Hold the dust container lid and with the other hand rotate the container in a anti clockwise direction to release Hold the container lid and rotate the separator in an anti clockwise direction to release Remove the pre motor filter from inside the separator and tap to remove any excess dirt from the filter it is also recommended to clean the separator Once dirt is removed the filter can be rinsed under the tap The pre motor filter should be washed after every five bin empties Wash under 24Hrs hand warm water Remove excess water and leave to dry for 24 hours When completely dry refit the filter Cleaning the Exhaust Filter Underneath the dust container you can find the exhaust filter Lift to remove the exhaust filter Remove any dirt debris by rinsing under water Max 40 C Leave to dry for 24 hours or until fully dry before replacing back into the cleaner IMPORTANT Do not operate your cleaner without either the dust container or filters in the right place Cleaning the Separator Turn the dust container lid anti clockwise to unlock and lift to take out T
6. harge is not hazardous to health Do not use your appliance out of doors or on any wet surface or for wet pick up Do not pick up hard or sharp objects matches hot ashes cigarette ends or other similar items Do not spray with or pick up flammable liquids cleaning fluids aerosols or their vapours Do not run over the power cord when using your appliance or remove the plug by pulling on the power cord Do not continue to use your appliance if it appears faulty Hoover service To ensure the continued safe and efficient operation of this appliance we recommend that any servicing or repairs are only carried out by an authorised Hoover service engineer Do not stand on or wrap the cord around arms or legs when using your appliance Do not use the appliance to clean animals or people When using the cleaning tools ensure to always steady the appliance with your other hand This will ensure that the appliance does not fall while in use WARNING A thermal cut out switches offthe appliance to prevent overheating if it is used when full or there is a blockage or dirty filters If this should happen then switch off unplug and correct the fault It will take approximately 45 minutes for the cut out to automatically reset The Environment The symbol on this appliance indicates that this appliance may not be treated as household waste Instead it must be handed over to the E applicable collection point for the recycling of elec
7. mined and found to be in Working order has not been assembled in accordance with these instructions or has been used incorrectly WARNING A thermal cut out switches off the cleaner to prevent overheating if it is used when full or there is a blockage or dirty filters If this should happen switch off unplug and correct the fault It will take about 45 minutes for the cut out to automatically reset IMPORTANT Do not run cleaner over the supply cord as this could damage the supply cord insulation IMPORTANT INFORMATION Hoover Service Should you require service at any time please contact your local Hoover Service Office Hoover spares and Consumables Always replace parts with genuine Hoover spares These are available from your local Hoover dealer or direct from Hoover When ordering parts always quote your model number USE ONLY HOOVER SPARES SPARE PARTS amp CONSUMABLES CODE U76 35601699 D156 35601698 FILTERS KIT HOSE AGITATOR Y36 35601697 BELT V37 35601700 PET HAIR amp ALLERGEN REMOVER J44 35601064 Quality Hoover s factories have been independently assessed for quality Our products are made using a quality system which meets the requirements of ISO 9001 GUARANTEE STATEMENT The guarantee conditions for this appliance are as defined by our representative in the country in which it is sold Details regarding these conditions can be obtained from the dealer from whom the appliance was purchased
8. trical and electronic equipment Disposal must be carried out in accordance with local g environmental regulations for waste disposal For more detailed information about treatment recovery and recycling of this appliance please contact your local city office your household and waste disposal service or the shop where you purchased the appliance C HOOVER Limited Pentrebach Merthyr Tydfil Mid Glamorgan CF48 4TU UK This appliance complies with the European Directives 2006 95 EC 2004 108 EC and 2011 65 EU il i GETTING TO KNOW YOUR CLEANER HANDLE PET HAIR 8 ALLERGEN REMOVER HOLDER Effortless cleaning PET HAIR 8 ALLERGEN with your new REMOVER Hoover HOSE HOSE HOOK BIN RELEASE BUTTON BIN HANDLE BIN LID f CORD HOOK y CREVICE TOOL DUSTING BRUSH 7 BIN HOSE CONNECTOR SIMS CORD HOOK U This vacuum cleaner is supplied with an Energy Label as required by European Regulation EU N 665 2013 The label shows a red prohibition REAR WHEEL A JA circle on the right covering the hard floor symbol This indicates that the vacuum cleaner is not suitable for use on hard floors Certain models only 59 EC i PREPARING TO USE YOUR CLEANER POWER SWITCH SETTING Switching on and off 1 Using a cross head screw driver remove the screw from rear of the cleaner main
9. urn the separator anti clockwise to remove from the dust container lid Tap separator over a bin to remove any dirt debris Using a soft brush clean any dirt debris out of the separator Refit the container top Please pay attention to alignment tab Twist the top part of the container whilst holding the lower part to lock together IMPORTANT Switch cleaner off ji and remove plug from electricity Wa CHANGING THE BELT OR BRUSH If your cleaner is not picking up efficiently the belt or brush or both may need replacing but first make sure you have EAI de supply before checking the A brushes or removing hood IMPORTANT Switch the cleaner off and remove the plug from electricity supply e before dismantling cleaning Replace belt This cleaner is unlikely to become blocked except by overfilling of dust container or accidentally picking up large solid objects Cleaning a blockage is simple Emptied th t tainer MPSA ine Gueh comet Remove the old belt then locate the new belt around the motor spindle and the brush Locate the right hand of the brush into the Cleaned the filters e Checked for blockages Remove foot plate Turn the machine over Locate the four screws as shown opposite Remove the screws completely
Download Pdf Manuals
Related Search