BLUEDRY USER MANUAL ECO FRIEN D LY
Contents
1. MD BLUEDRY BLUEDRY USER MANUAL Model HD BD1000 CERI E PLEASE READ CAREFULLY THROUGH THIS MANUAL BEFORE USING THE PRODUCT OBSERVING ALL SAFETY INFORMATION WARNINGS 1 WARNING 2 NOTE This product is intended for installation Do not install dryer over washbasin by a qualified service person If the power supply cord is damaged it Disconnect power at the service breaker must be replaced by the manufacturer or its before installing or servicing service agent or a similar qualified person Failure to properly ground unit could in order to avoid a hazard Means for result in severe electrical shock disconnection must be incorporated in the All units must be supplied with a 3 wire fixed wiring in accordance with the current connection The ground wire must be wiring regulations connected to the dryer s backplate 3 SPECIFICATION Voltage 220V 240V 50 60Hz 8A 1800W Hot 2 4A 550W Cold 110V 120V 60Hz 16A 1800W Hot 4 8A 550W Cold Air Temperature 45 C D 10CM Room Temp 25 C Air Velocity 60M S Air Flow 140M3 H Drying Time 8 10S Sensor Range 5 15CM Protection Level IPX1 Electric Isolation CLASS 1 Brush Motor 25000R M Noise at 1M 74dB Cabinet Material Stainless Steel 304 4 INSTALLATION l Installation must be carried out in 170MM 1800 Watts or heater off 550 Watts accordance with the current edition of the local wiring regulations code having2. Mr Ad c X J tees Do Pid ce ING a PP PPP A AA Signature amp Sam Pozioni bluedry co uk Blue Dry is a part of FW3 Group LTD B L E D RY FW3 Group West Hill Nr Exeter Devon UK EX11 1LQ Tel 0800 328 5708 Email sales fw3group com
3. jurisdiction Installation should be performed only by a qualified electrician The switch is clearly marked Replace cover Do not over tighten Screws Connect the hand dryer plug to the power supply 2 Place template against wall at a Connect the live wire coloured desired height see mounting height Brown or Red to the terminal block recommendations and mark locations marked L of 4 mounting holes Dia 8mm 5 167 b Connect the neutral wire coloured 3 Remove and retain 2 side security hex Black or Blue to the terminal block cover screws and cover Then mount marked N the hand dryer base on the wall c Connect the ground wire coloured 4 Before replacing the cover there is Green or Yellow to the terminal block 5 an option to run the dryer heater on No touch operation There is a blue LED light to guide user to the air flow Shake excess water from hands marked E OPERATION Place hands under the outlet to start operation Rub hands lightly and rapidly Stops automatically after hands are removed 6 MAINTENANCE 7 PACKING LIST Periodic cleaning of the unit is recommended Remove cover and clean dryer dust lint Wipe the cover with a damp cloth and mild cleaning solution Do not soak Never use abrasives to clean the cover Hand Dryer 1PC User Manual 1PC Installation Template 1PC Plug in Dia 8x38mm 4PCS Screw in Dia 5x36mm 4PCS Hex screwdriver 1PC 8 DIAGNOSTIC
4. S REMEDIES If the dryer will not run If the dryer cycles by itself runs all the time or is not sensitive enough If the heat element gets hot but the fan motor does not turn If the dryer runs but makes a buzzing sound If the fan motor runs but the heating element does not get hot dryer blows cold air If the motor makes a ticking whin ing noise when it rotates Ensure the breaker supplying the dryer is operational If it is disconnect the power and remove the dryer cover Taking suitable precautions to avoid shock hazard reconnect the power and check for voltage at the terminal block If there is power and the dryer will not run replace the Electric Circuit Board large one and or Microcomputer Board Middle one and or Sensor Board Turn the blower wheel several times by hand to establish if it is blocked Ensure that there is no obstruction on or in front of the infrared sensor Clean any dirt off the sensor lens Try adjusting the sensitivity potentiometer on Microcomputer Board Blue knob Turn anti clockwise to decrease the sensor range If the problem persists replace the Microcomputer Board and or Sensor Board Disconnect the power Remove the dryer cover and check for obstructions in the fan housing Damaged fans must be replaced If there are no obstructions replace the motor or brushes Disconnect the power Remove the dryer cover and check the fan for rubbing on the housing as its rotat
5. es Replace fan if the condition exists Disconnect the power and remove the dryer cover Check that the heat on off switch is switched to on Check loose and damaged wires Remove the blower housing Check the heating element to see if it is burnt or damaged Damaged element must be replaced If the element does not appear damaged disconnect it at the Electric Board and check element wire continuity Please check thermostat on the heating element at the same time Disconnect the power Remove the dryer cover and check the brushes for worn condition replace them if necessary 9 DIAGRAM L 220 230V 50 60Hz Pip qu N O OR 110 120V 60Hz Earthing Heat Element D Turn clockwise to increase sensor range QQ HOT COLD Switch ast o Blue LED Light D Program Board LS gt SSS B veuow 9999999 Terminal ai e ow w LL Block Ze Blue D Q Brown 000 660 Blue A Brown a Transformer TIA o EJ NEC acce Hand Dryer Main Circuit Board 10 WARRANTY This hand dryer has a 2 year warranty from the date of purchase for any manufacturing defect It covers replacement of defective parts except when caused by improper use This warranty is only valid if the form card has been properly filled in with the suppliers stamp For all warranty claims you should contact your local distributor vor pe s dy et ASIDUO RM A Uo
Download Pdf Manuals
Related Search