Installation Manual(CCM04)_eng.indd
Contents
1. e After the back coveris For the Terminal Group is fastened to fix up the standing out of the back cover front cover first lock so it is necessary to obligate Battery 3V Note that the positive and negative one of the two then the holes and it is forbiden to poles are in right positions when loading batteries another fasten difectly to the wall Instruction for installing When a weekly schedule controller is needed a small 2 cores wire and 3 cores wire NOTE should be added Connect with the same colour e The connecting wire should be a little longer as to take away the switch board easily for maintenance e The connecting wire should be a little longer as to take away the controller easily for maintenance Wiring diagram between Weekly Shedule Controller and Indoor Unit A Main Board With External Network Module 3 CORES SHIELD WIRE NET EYX INDOOR MAIN NETWORK BOARD MODULE EE I z3 g 2 CORES WIRE N AN YELLOW l BLACK V E Ee Y X WEEKLY SCHEDULE DISPLAY BOARD CONIR E B Main Board Integrated Network Module 3 CORES SHIELD WIRE EYX INDOOR MAIN BOARD Z Lu S lA m z or 2 CORES WIRE YELLOW BLACK DISPLAY BOARD2. dule controller and Indoor Unit Otherwise electricity leakage or heating may be caused which may result in fire 2 Install the Wire joint 5p to the appointed position of the electric controlling Box Wire must be suitable for weekly schedule controller never bring outside 3 Circuit of weekly schedule controller is low voltage circuit Never connect it with force to bear on the terminal a standard 220V 380V circuitor put it into a same Wiring Tube with the circuit E and the interval must be more than 300 500mm 4 The shield cable must be connected stable to the ground or transmission may fail 5 Do not to attempt to extend the shield cable by cutting if it is necessary use Terminal Connection 6 After finishing connection do not use Megger to have the installation check to C the signal wire p INSTALLATION PROCEDURE a Wiring technique and principle Wood Mounting Screw M4X20 While installing using Screwdriver or other tools to open the back cover from the inside Circuit board Back cover of Weekly Schedule Controller Front cover of Weekly Schedule Controller Weekly Schedule Controller 2 cores wire LCD display RSEN I Weekly Schedule Control Board ji N 3 cores wire Turning cover
3. ee em WEEKLY SCHEDULE CONTROLLER DE COMMISSIONING DISMANTLING amp DISPOSAL This product contains refrigerant under pressure rotating parts and electrical connections which may be a danger and cause injury All work must only be carried out by competent persons using suitable protective clothing and safety precautions A OA Read the Manual Risk of electric shock Unit is remotely controlled and may start without warning Isolate all sources of electrical supply to the unit including any control system supplies switched by the unit Ensure that all points of electrical and gas isolation are secured in the OFF position The supply cables and gas pipework may then be disconnected and removed For points of connection refer to unit installation instructions Remove all refrigerant from each system of the unit into a suitable container using a refrigerant reclaim or recovery unit This refrigerant may then be re used if appropriate or returned to the manufacturer for disposalUnder No circumstances should refrigerant be vented to atmosphere Where appropriate drain the refrigerant oil from each system into a suitable container and dispose of according to local laws and regulations governing disposal of oily wastes Packaged unit can generally be removed in one piece after disconnection as above Any fixing down bolts should be removed and then unit lifted from position using the points provided and equipment of adequate lifti
4. lectrical Switch Box N CAUTION 7 4 Installation Manual 1 Installation must be conducted by professionals 5 Owner s Manual 1 a Others may perform improper installation which cause electric shock or fire 6 6 terminal Group 4 RS9005E Follow this manual as strictly as possible 7 Terminal Installation Screw 2 ST3 9x12 F H Improper installation may cause electric shock or fire 2 Preparing for the following at site Another installation must be performed by professionals f i j Number Name Quantity Type Remarks Improper installation may cause electric shock or fire 1 3 cores wire 1 RVVP 0 5mm x3 The factory scheme wire is 10m Do not disassemble your air conditioner at will j i 2 The longest wire is 20m A random disassembly may cause abnormal operation or heating which may result in a 1 RVVP 0 5mm x2 fire 3 Switch Box 1 4 Wiring Tube Insulating Sleeve and Z _ Tightening Screw N NOTE Weekly Schedule Controller Installation Notice Do not install it in a place where combustible gas easily leaks 1 This manual contains information about the procedure of installing weekly Once combustible gas leaks and remains around weekly schedule controller fire may be schedule controller caused Please refer to Indoor Unit Installation Manual for connecting between weekly Wire must be suitable for the current of weekly schedule controller sche
5. ng capacity Reference MUST be made to the unit installation instructions for unit weight and correct methods of lifting Note that any residual or spilt refrigerant oil should be mopped up and disposed of as described above After removal from position the unit parts may be disposed of according to local laws and regulations Johnson Wy Controls YDSO6I 016aW Eee
6. wa YORK cc ENGLISH YDSO6I 016aW INSTALLATION MANUAL WEEKLY SCHEDULE CONTROLLER AMRO02M For correct installation read this manual before starting installation Only trained and qualified service personnel should install repair or service air conditioning equipment Users should not install the air conditioner by themselves All pictures are only sketches If there is any difference between pictures in this manual and the actual shape of the air conditioner you purchased the actual shape shall prevail WEEKLY SCHEDULE CONTROLLER INSTALLATION MANUAL B Model AMRO2M Version YDSOGI 016aW k A P 7 SAFETY PRECAUTIONS So OTHER PRECAUTIONS S Z Please read this safety precaution carefully before installation Installation Location Z Do observe the following safety precautions for they are very important Do not install it in a place with oil steam or sulphur gas or else deform or malfunction may occur CAUTION This sign warms of death or serious injury Preparation Before Installation 1 Make sure the following pasts has been prepared AX NOTE This sign warms of injury or damage to property Number Name Quantity Remarks 4 Conform there is no abnormal phenomena during test operation after complete 1 Weekly Schedule Controller 1 then 2 _ Wood Mounting Screw 3 M4X20 For Mounting on the Wall 3 Mounting Screw 3 M4X25 For Mounting on the E
Download Pdf Manuals
Related Search