Single Line Keypad SLK-1 Installation Manual
Contents
1. Incremental volume adjustments can be made by either pressing and releasing the volume up or down button while pressing and holding will ramp the level until released or the maximum minimum level is reached The volume level is displayed by a bar graph at the bottom of the LCD panel and a numeric value is displayed during adjustment The SLK 1 is designed for basic zone control As such it does not provide control of connected sources or adjustment of zone audio properties such as Bass Treble Loudness or Balance These can be configured through SCS C5 Configuration Software The SLK 1 is an ideal companion for systems using the My Russound application on supported hand held devices The FAV button is a user favorite preset The preset can be selected at any time to recall source selection and volume To store a preset adjust the room setting and select a source to be stored Press and hold the Fav button until F1 SAVED is displayed on the LCD panel Now a press and release will recall the favorite preset When used with the DMS 3 1 the current medial will always be saved e g SiriusXM station or internet radio station The FAV button corresponds to the F1 button on SRC C5 remote SLK 1 Side Panel The SLK 1 setup button is located on the right side of the keypad when facing front This is covered when a trim plate is installed OS UPDATE RUN JUMPER The pins are jumpered only when performing an OS update on the keypa2. connected or consult the dealer or an experienced radio TV technician for help This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme a la norme NMB 003 du Canada SLK 1 Diagnostics Menu The Diagnostics Menu allows the installer to run a diagnostic check on the SLK 1 and to verify the firmware version To access the Diagnostics Menu press and hold the Setup button on the Press and right side of the keypad until Diags appears on the display The menus are outlined in the diagram below When finished press and release the Setup button again Hold SLK Diagnostics Menu Setup Button ce ayr DIAGNOSTIC wy OTE CONTROLLR PORT ID KEYPAD ID VERSION foun a ID L jo Doo G ma Displays Controller ID number to be tested Press Vol Up Dwn to scroll characters Warranty and Repair The Russound SLK 1 is fully guaranteed against all defects in materialsand workmanship for two 2 years from the date of purchase During this period Russound will replace any defective parts and correct any defect in workmanship without charge for either parts or labor For this warranty to apply the unit must be installed and used according to its written instructions If service is necessary it must be performed by Russound The unit must be returned to Russound at the owner s expense and with prior written permission Accidental damage and shipping damage
3. Safety Instructions 1 Read Instructions All the safety and operating instructions should be read before the equipment is operated 2 Retain Instructions The safety and operating instructions should be retained for future reference 3 Heed Warnings All warnings on the equipment in the operating instructions should be adhered to 4 Follow Instructions Follow all operating and user instructions 5 Water and Moisture The equipment should not be used near water for example near a bathtub washbowl kitchen sink laundry tub in a wet basement or near a swimming pool 6 Mounting The equipment should be mounted or secured as recommended by the manufacturer 7 Heat The equipment should be situated away from heat sources such as radiators heat registers stoves or other equipment including amplifiers that produce heat 8 Power Sources The product should be connected to a power supply only of the type described in the operating instructions or as marked on the equipment 9 Grounding or Polarization Precaution should be taken so that the grounding or polarization means of the product is not defeated 10 Avoid spills and foreign objects Ensure liquids and objects don t get into the product enclosure through any openings 11 Damage Requiring Service The equipment should be serviced by qualified service personnel when the power supply cord or the plug has been damaged objects have fallen liquid has been spille
4. are not considered defects nor is damage resulting from abuse or from servicing by an agency or person not specifically authorized in writing by Russound This Warranty does not cover Damage caused by abuse accident mis use negligence or improper installation or operation Power surges and lightning strikes Normal wear and maintenance Products that have been altered or modified Any product whose identifying number decal serial number etc has been altered defaced or removed Russound sells products only through authorized Dealers and Distributors to ensure that customers obtain proper support and service Any Russound product purchased from an unauthorized dealer or other source including retailers mail order sellers and online sellers will not be honored or serviced under existing Russound warranty policy Any sale of products by an unauthorized source Displays Displays Keypad ID current firmware number version BUTTON DISP DISP DISP TEST wee hy S A a ae os ROW Press button O Press Vol Up Dwn to scroll rows or other manner not authorized by Russound shall void the warranty on the applicable product Damage to or destruction of components due to application of excessive power voids the warranty on those parts In these cases repairs will be made on the basis or the retail value of the parts and labor To return for repairs the unit must be shipped to Russound at the owner s expense along with a note explaini
5. d and removed during normal operation 2 SETUP BUTTON Activates information and update menus for the keypad 3 OS UPDATE PORT Used to directly update the SLK 1 keypad operating system firmware If an update is released it will be available online through the Support Center on www russound com Look in the C Series System Firmware amp Software Updates section under C Series System The Advanced Programming Cable is available from Russound Part 2500 521065 SLK 1 Front View SLK 1 Top View SLK 1 Color Conversion You will need both small straight and Phillips head screwdrivers to change the color plates on the keypad The Bezel Molding and Buttons will be switched for the new color plates 1 If installed remove the SLK 1 keypad from the wall Gently pull the Trim Plate off the mounting plate Unscrew the unit from the electrical box and disconnect the cable 2 Unscrew the plastic Frame Plate Keep the Frame Plate and screws for reattachment later 3 Remove the Bezel Molding by gently pressing in each of the 4 locking tabs 2 per side while pushing it away from the metal frame CAUTION To avoid damage to the LCD panel do not use hard edged tools 4 Remove the Display Lens from the Bezel Molding by gently pushing from the rear to overcome the clips 5 Once the Display Lens is removed put aside for reattachment later Be careful to not damage the display 6 Remove individ
6. d into the equipment the equipment has been exposed to rain the equipment does not appear to operate normally or the equipment has been dropped or the enclosure is damaged 12 Servicing The user should not attempt to service the equipment beyond that described in the operating instructions All other servicing should be referred to qualified service personnel 13 Care From time to time you should wipe any dust accumulation from the equipment with a soft dry cloth Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a_ residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of or more of the following measures reorient or relocate the receiving antenna increase the separation between the equipment and receiver connect the equipment into an outlet on a circuit different from that to which the receiver is
7. eption 5 Volume UP Down Raises lowers the volume for the room Source Select Press and release scrolls through the available sources D Previous Navigates backwards through menus or play previous selectionk Forward Press to forward through menu or play next selection Power Turns room ON or OFF when pressed once button remains lit when OFF if any other zone in the system is ON 9 IR RECEIVER Receives IR signals and passes them to the controller and source equipment Also used when the keypad is operated using the SRC C5 C Series System remote controls Favorites Selects preset user selected favorite settings per room 1 Play Pause Toggle between play and pause Red LED will blink to indicate IR remote reception Press Volume Up or Down buttons to adjust volume level Press and release source button to scroll through the available sources SLK 1 1 User Mode The User Mode allows the user to select an audio source adjust the volume level in the zone turn the zone on off and issue system wide All On All Off commands To turn the zone on or off press and release the power button A press and hold while in the On state will issue an All On command and a press and hold in the Off state will issue an All Off command To select a source press and release the source button to increment to the next available source The configured source name will be displayed on the keypad s LCD panel
8. ng the nature of service required Be sure to pack the unit in a corrugated container with at least three 3 inches of resilient material to protect the unit from damage in transit Before returning a unit for repair call Russound at 866 888 7466 for a Return Authorization number Write this number on the shipping label and ship to Russound ATTN Service 5 Forbes Road Newmarket NH03857 Copyright 2012 Russound All rights reserved All trademarks are the property of their respective owners Russound is not responsible for typographical errors or omissions Specifications are subject to change without notice Russound Inc 5 Forbes Rd Newmarket NH 03857 USA tel 603 659 5170 fax 603 659 5388 www russound com technical support 866 888 7466 e mail tech russound com 28 1375 08 28 12 RiRussound S Single Line Keypad SLK 1 Series Installation Manual The SLK 1 keypad is an in wall Decora style single gang keypad designed for individual zone control of MCA C3 MCA C5 Multiroom Controller Amplifier wall plate not included D System Info SYS ON indicates other active zones and SHARED indicates the selected source is in use in another zone 2 LCD Panel 5 character white backlit display shows source name volume and room status 3 Volume Level 21 segment volume level bars increase from left to right to indicate volume level 4 IR Confirmation Loudness LED Red LED blinks to confirm IR signal rec
9. oller RJ 45 Connection Each keypad connects to a Keypad Port on the back of the controller MCA C3 controller shown below Connections are made using CAT 5 cable with an RJ45 connector wiring scheme shown below An SA ZX3 Keypad Splitter can be used to add additional keypads to each zone SLK 1 CAT 5 Cable AAI i L AVAAJA RIRussound NEWMARKET NH U S A SA ZX3 O Keypad Splitter CAT 5 Cable RJ 45 using T568A Wiring Standard GREEN BLUE BLUEWHITE 0 ORANGE GREEN WHITE ORANGE WHITE BROWN WHITE BROWN Specifications Power requirements 12 VDC 180mA CAT 5 CAT 5e connection RJ 45 T568A standard Dimensions 1 875 W x 2 7 D x 1 47 H 4 7 x 6 9 x 3 7 cm Weight 4 5 oz 127 6 g Max cable length 300 CAT 5 Fits 1 Gang UL CSA Approved 18 ci Junction Box Conforms to UL60065 Certified to CAN CSA IEC60065
10. ual button caps by pulling them off the key mat 7 Reverse the order for installation taking the following precautions a Place button caps correctly on the key mat Make sure the key mat is positioned properly on the circuit board and without dust or debris on the button contact points prior to attaching the Bezel Molding b Make sure that there isn t any debris or fingerprints on either the display or back of the Display Lens prior to reattachment c Useaclean dry lint free soft cloth to gently wipe the display or back of the Display Lens to clean if necessary Never use cleaning agents as this can cause streaking or permanent damage to either part Note Place individual buttons on key mat matching the diagram below JUUL A D x lt VOL SOURCE FA PEDE HEEE 0000 Metal Frame Buttons Bezel Molding Individual Buttons Keypad Installation 1 Check whether or not you can route the wire to the location you have chosen 2 To install a single gang keypad you will need to use an UL CSA approved plastic single gang 18 ci electrical box 3 Route CAT 5 cable to the junction box from the MCA C3 C5 system controller 4 Terminate the CAT 5 cable with an RJ 45 connector using the T568A wiring standard 5 Mount the keypad in the electrical box and attach the trim plate Electrical Box SLK 1 Keypad Frame Plate Trim Plate SLK 1 Keypad to MCA Contr
Download Pdf Manuals
Related Search