HEATING REGULATOR EPC11 End user manual
Contents
1. Operation modes of generator OFF The generator is not activated ON The generator is activated Operation modes of intermediate circuit pump OFF The pump is not activated ON The pump is activated 3 2 District Heating The transfer station is called as district heating it supplies the heat energy via a heat exchanger Primary Valve This indicates the status of the opened district heating valve Max return temperature The set highest return temperature into the district heating network Figure 4 District heating menu Return temperature The current return temperature into the district heating network Power This indicates the current power output of district heating to the transfer station Counter When selecting this menu Item the heating counter data menu will open up This menu will show the most important data if a heating counter is connected and connected with the regulator Figure 5 Heat meter menu 10 3 3 Domestic hot water tank The warm water boiler is used to prepare and make avallable the necessary heated water for usage Mode This indicates the current operation mode of the boiler Figurre 6 DHW tank menu MinChg The boiler always carries out a minimum loading outside its loading time If the minimum temperature of the boiler has fallen below Disinf The boiler carries out its weekly disinfection charge Upper temperature This indicates the current upper boiler temperature Moreo2. 2011 ENERPIPE GmbH All rights reserved This manual has been issued by ENERPIPE GmbH for use ENERPIPE GmbH reserves the right to revisions and amendments of this manual at any time and with no obligation to announce or to notify the users about such amendments made Table of Contents sii Agro LCS sista NU ne D 2 Regulator ri 6 Ao APA e 6 A ee 7 a e a haat atten cased oenattics ata nena caalainan ha ciate nit 7 Lowering MOS a a douse Np a amen ead O D 7 Hedin MOU C asa 7 Automate Mode is 7 DU a ee a ee en eee 7 A et Set eee Mee 7 MAINTENANCE cosacos a dibicia 7 2 3 Correction of Day Night Mode toi oie 8 Day mode Correction of day mode occccoccnccccnnccncnnccncnccnnnnonncnnnononnnnnnnonncnnnnnnnnnoneness 8 Lowering Mode Correction of Lowering Mode ooocccccccnnccnncccnnconcncnnnnnnnnnoaroncnonnnos 8 3 Regulator MENU snask eane E vasnanidouaeedmtancrvinesaadianm needa 9 SI o O 9 Modes TOF district A a 9 Operation modes of heating circuits a 9 Operation modes of domestic hot water tank cccoocccncnnccnnccnncnnononcnnnnnnennnnonennnnanennnss 9 Operation modes OF circulation o dd o 10 Operation modes of solar Neat in 10 Operation modes Of DU knea a i ce ee ei ae he 10 Operation modes of generator lc 10 Operation modes of intermediate circuit pUMp occcccoccnccnnconncnnnononnnconocnncnnncnnronononenss 10 32 DISTIN Ss 10 A A ue 10 Max Tetu temperature eds 10 Return temperature ssni hee thera ace AA tae es A eee
3. in this function consult your district heating operator Power output limitation The supply power is limited to the connect load as per your contract For questions or requests for changes in this function consult your district heating operator Operation modes of heating circuits OFF The heating circuit is not activated ON The heating circuit is in normal operation mode RPW Residual power gt electric water heater is preferred the heating circuit is reset SBK The heating circuit is in lowering mode DHW Secondary warm water setting gt heating circuit is OFF during boiler charging FP The antifreeze is activatedBetriebsarten Solar BCK Blocking gt e g within blocking time 0FF MAN Manual operation AHZ Baking out program gt Drying of stone floor is activated EXT External required default value ON Operation modes of domestic hot water tank OFF The tank is in charging mode ON The tank is in loading time MAN Manual operation FP The antifreeze is activated MIN The minimum load is activated LSP Blocking of load gt temperature of initial operation has not been reached EXT Release for external tank charging Operation modes of circulation OFF The circulating pump is not activated ON The circulating pump is activated Operation modes of solar heating OFF The solar pump is not activated ON The solar pump is activated Operation modes of buffer OFF The charging pump is not activated ON The charging pump is activated
4. saaimereduesmasasaiaweieetalisasseatn snrednasmasebasa oreo taseassoaxaeniadnanutananiateds 15 Secondary required initial operation session sti 19 Secondary temperature of Initial operation oocccccoccnncconcnnononcnnnnnnononnnronocnarononononos 19 Y eo ou aaneeeaeeaegnasuteeazastasone ua eceenecads Geena 15 MEASURE oo is 15 7 er ie dialec CUED UND eee 15 MOIE caren a S a 15 Secondary required initial operation ooccccccocnncccncnnccnnnonocnncnnnconcnnnnoncnnonnnnnnnnaranonnnos 19 Temperature of secondary Initial operation occccocncocncononnnnccncnnonacnncnnnnonarononnnnononoss 19 PTS OO Helle COM O PPP E HO 2 ice saccnctense anne seseecsoacelaecesedenctoestaasods 16 DME Mi ail LEVEL salido trio dncond 17 dl Entrance INTO Ie WO V Ole Site te aes iio 17 A 17 nicas CaN AAA tahoe eeaseaaeayseesaesoneataeeecte setre 17 A ooo 17 e A CE 17 OW ROUDLESI O OEMS sia 17 641 Mente ms cannot DEVO CeO siirsi aiaa eaa E A E Eai 17 6 2 NO temperature display assoi clau EASA TEAREN 17 AA 17 1 Safety notes Danger of scalding Some parts of this system may reach temperatures exceeding 55 C for thresholds of burning see EN 563 Be sure to point out all possibly existingdangers such as touchable surfaces high temperatures of used water to all persons operating this system Danger of freezing Make sure that the selector switch does not remain in the MAINTENANCE position forlonger periods of time during
5. whereas an automatic synchronization of the clock time will be carried out once In 24 hours if this regulator is connected with the district heating operator via network If this is not the case the clock time can be set manually 5 4 Time of absence Time of absence FROM During a time of absence all heating circuits will be regulated on permanent lowering This setting will configure the first day of the absence function starting around 00 00 Figure 17 Menu of absence Time of absence TO During a time of absence all heating circuits will be regulated on permanent lowering This setting will configure the last day of the absence function ending at 24 00 5 5 Naming the circuits The individual heating circuits can be named individually here As per default the names with the heating circuit including the number of the heating circuit are given 6 Troubleshooting 6 1 Menu items cannot be opened Individual menu items which do n ot open are not accessible in your current level of authorization For changes and questions please consult your district heating operator 6 2 No temperature display Please note that temperature will only be indicated if a temperature sensor is connected and in full working condition respectively In case of a problem with a sensor please consult your district heating operator immediately 6 3 Other Problems In case of other malfunctions please consult your district heating operator im
6. winter The heating pipes may freeze up MAINTENANCE position There is no antifreeze monitoring CAUTION To disconnect the unit from the mains use the all polar switch on the part of the builder Only a qualified expert must open the unit The unit is completely maintenance free 2 Regulator 2 1 Key allocation Correction Day Night Mode 4 0 C to 4 0 C or 8 0 C to 0 0 C _ ENERPIPE ii 4 Abort Key Confirm Key Escape Enter Navigation Key Navigation Key Up Down Modes OFF Antifreeze Blue Lowering Mode Orange Heating Mode Orange Automatic Mode Green Boiler Mode Orange Party Modus Orange MAINTANANCE Red 2 2 Modes A lamp on the selector switch indicates the current mode The newly selected mode will be displayed on the regulator screen when changing another mode Off Antifreeze The regulator s operation will be deactivated except of the antifreeze switch function The antifreeze switch function will be activated when the external temperature falls below the antifreeze temperature Lowering Mode The lowering mode of the heating circuits will be activated regardless of the timer program i e the required temperature will be reduced in accordance with the settings Remote control has priority For explanation please refer to Room remote control on page 16 Heating Mode The heating mode of the heating circuits will b
7. cee Aes 10 AI o Bee hah oO a O ets ds near CR as E no bl 10 o IP A 10 3 2 WOMMESTIC NOU Water TANK sa 11 MOGE arisna ee eee ee 11 do uo Sn Sad ot ae hart hit Teak 11 Lower LEM Pera U AAA A A 11 OA GING TIM OS sr a 11 o a 11 y A a 11 Operation tme A A seen tenet St eee dae Mice bote See a 11 Return temperature ad deL 11 SO Rea Und CHC UNS serna audroiicadag dumbed uaetdae haan auanned ac musta tat eaand nem besaantoielaae 12 PREG UIFE HOO Ii temperature e E E ds e ad ot ao E ad 12 Room TEMP el US a Al le 12 Required temperature of Initial operation ccoocccccoconoconnnnonnnocncnnonnnnnnonnnonncnnnnnnnonnns 12 Actual temperature of Initial operation ccoocccccoconocncnnonnnnocnnononnnnnnononononnnonacnnnnnanoss 13 Heating times LOwering times serisi ee eee tere nee ere are ee eee 13 A E E E eanstoedraee ieee E ENEE 13 Rolauonatspeed or PUNO sd os 13 A a E A dieie arate aaundeceace eto 13 Upper required temperature ido 13 LOWer TEM Dela tUl E earar e r di a 13 Lower reduired temperature nrnna dl 13 Burer toading UMES ad 14 ES ate aca osze dah eae gence sanedeateaienacaearenatacesancsessuadateetenence 14 PO tato tl speed o OUI D gires iaa 14 Collector temperat re sax c82casccunsanatcnedenasagacedssasieaconsnancaenndneseasatencadareuaicansaeazcentesteoesea 14 LOWE POND Cl el CUI eega eind 14 Temperature of initial solar operation soii 14 Bello URE a eee 14 PA PPP ESENTSE 14 A nn A eles 14 A csicuct dousnisee
8. e activated regardless of the timer program Remote control has priority For explanation please refer to Room remote control on page 16 Automatic Mode The mode of the heating circuits heating or lowering mode depends on the timer program and remote control Boiler Mode The heating circuits are deactivated except of the antifreeze The boiler is charges in the usual way Party Mode The heating mode of the heating circuits is activated for a certain period of time adjustable After this period of time has expired the regulator returns to the last selected mode MAINTENANCE Switching off all outputs no regulator function will occur CAUTION NO Antifreeze 2 3 Correction of Day Night Mode Day mode Correction of day mode The day mode must be set with the rotary button on the top right The value can be set from 4 C to 4 C and causes a permanent increase In the heating circuits temperature of the initial operation during day mode The value here stands for the room temperature If no room sensor Is connected this value Is regarded as Increasing or lowering the respective temperature of Initial operation respectively so the room temperature around the set value will be changed Figure 1 Correction of day mode Lowering Mode Correction of Lowering Mode The lowering mode Is set with the rotary button on the top right and then with the arrow key The correction mode for the lowering mode has
9. is your home system and the district heating on the primary part 15 4 Room remote control It is possible to provide each heating circuit with an own remote control This remote control allows for selecting the following functions Betriebsarten Automatikbetrieb Tagbetrieb Nachtbetrieb AUS Frostschutz Raumkorrektur 4 0 C bis 4 0 C Figure 15 Remote control A priority select switch AUTOMATIC DAY NIGHT OFF is provided for pre selecting the operation mode An adjusting control with a range of plus minus four degrees is provided for changing the required room temperature A room sensor Is integrated in the remote control which can be used for applying various regulating programs for heating as well as for optimizing the ENERPIPE regulator CAUTION The selector switch of the regulator will have priority over the remote control if the selector switch of the regulator is set to OFF Antifreeze boiler charging or maintenance 16 5 Internal Level 5 1 Entrance into the level Hold both arrow keys pressed in this main menu until the window Service Level appears on the regulator You will now find 4 different menu items there 5 2 Service code The service code is necessary for internal work on the regulator Your district heating operator is responsible for all information and work on this level Figure 16 Internal level 5 3 Time and date The regulator will set the clock time automatically
10. mediately Notes Version FW8 17 Release 11 07 2011
11. ng circuit stands for a cycle of heated water through a heating system such as radiators floor heating etc CAUTION Ifthe regulator s selector switch is set to OFF Antifreeze boiler charging or maintenance the selector switch of the regulator will have priority over the remote control Mode This indicates the current operation mode of the heating circuit Figure 8 Heating circuit menu without room control Selector switch The operation mode of the regulator is applicable However if it is set to the heating lowering mode or to OFF the remote control will have priority Party mode If the party mode has been set for the heating circuit the heating circuit will switch to the heating mode for the period of time set for the party mode Once this period of time has expired the heating circuit will return to the previous operation mode Timer program Regardless of the selector switch or remote control the heating circuit is in heating mode during heating times and in the lowering mode outside the heating times He ating mode The heating circuit is continuous in the heating mode Figure 9 Heating circuit menu with room control Lowering mode The heating circuit is continuous in the lowering mode OFF Antifreeze No control function of the heating circuit at all except of the antifreeze function Required room temperature The desired required room temperature can be set here However the requi
12. nk The buffer or heating boiler is a container which is used for storing heat energy It is used to store the energy obtained through district heating solar system or similar in order to avoid a continuous request for heat energy Rotational speed of pump This indicates the rotational speed of the buffer charging pump Figure 10 Buffer tank menu Upper temperature This indicates the current upper buffer temperature Upper required temperature This indicates the required temperature of the buffer It is the result of the maximum required initial operation If this maximum required initial operation is lower than the minimum upper buffer temperature this value will be used as required initial operation This value can be configured when selecting this item Minim um upper buffer temperature default 50 C This indicates the upper minimum temperature of the buffer Lower temperature This indicates the current lower buffer temperature Lower required temperature This indicates the currently calculated lower required temperature of the buffer The required temperature below Is calculated with the maximum return of district heating minus hysteresis The hysteresis can be configured when selecting this item Hysteres is of maximum return temperature buffer OFF This hysteresis is used for calculating the lower required buffer temperature The lower required temperature of the buffer is calculated with the maximum return
13. now been activated This value can be set from 8 C to 0 C and causes a permanent adaptation in the heating circuits temperature of the initial operation during the lowering mode The value here stands for the room temperature If no room sensor Is connected this value is regarded as increasing or lowering the respective temperature of initial operation respectively so the room temperature around the set value will be changed Figure 2 Correction of lowering mode 3 Regulator menu 3 1 Main Menu The main menu shows all the functions of the regulator Apart from that the regulator indicates the current modes as well as the current temperatures of the individually controlled components CAUTION Menu items which do not open are not accessible in your current level of authorization For changes and questions consult your district heating operator Figure 3 Main menu Modes for district heating OFF The district heating is not activated there is no energy transmission ON The district heating is in normal operation mode RLB The limitation to return is activated LBG The power output limitation is activated MAN The district heating valve is in manual mode manual EXT The district heating is OFF supply through external sources of energy e g boiler Limitation to return The district heating return temperature Is limited to a value set by the district heating operator For questions or requests for changes
14. red room temperature will be visible only if a room remote control has been connected Room temperature This indicates the current room temperature of the heating circuit However the room temperature will be visible only if a room remote control or a sensor has been connected Required temperature of initial operation This indicates the current required initial operation of the heating circuit Moreover the switch off temperatures can be configured here as well 12 Switch off temperature of day mode default 18 C If the mean value of the external temperature exceeds this value during day mode the respective heating circuit will be switched off heating circuit pump off mixing valve CLOSED Switch off temperature of lowering mode default 10 C If the mean value of the external temperature exceeds this value during lowering mode the respective heating circuit will be switched off heating circuit pump off mixing valve CLOSED Actual temperature of initial operation This indicates the actual temperature of initial operation of the respective heating circuit Heating times Lowering times The heating times or lowering times for the selected heating circuit can be defined here The type of the times is set in the basic configuration of the regulator Thus these terms in this menu item are called heating times or lowering times For changes or questions consult your district heating operator 3 6 Buffer tank heating ta
15. temperature of district heating minus this hysteresis 13 Buffer loading times The loading times of the buffer can be set here 3 7 Solar The solar pump switches on as soon as the collector temperature is higher than the buffer temperature in addition to the hysteresis Rotational speed of pump This indicates the current rotational speed of the solar pump Figure 11 Solar menu Collector temperature This indicates the current temperature of the solar collector Lower temperature This indicates the current solar buffer temperature Temperature of initial solar operation This value will only be visible if there is a module for regulating the rotational speed Moreover this value will only be necessary If the solar pump is controlled through the rotational speed Upper temperature This value will only be visible if there is a module for regulating the rotational speed 3 8 Generator Any additional sources of energy e g boiler are called generator The regulator itself distinguishes between a pure switching of a requirement of a generator Switching An existing heat generator is equipped with a temperature sensor If the sensor value of the generator is higher than the required initial operation in addition to the hysteresis for switching on the regulator will switch to the external heat generator The district heating will stop supplying after a switching The switching off occurs if the temperature of the genera
16. the generator will switch on when required This also shows the duration until switching on The parameter Switching on of Timeout can be configured when selecting this item Switching on of Timeout If the required initial operation for this time span falls below the external heat generator will be switched on Time until OFF This item in the menu will show the remaining duration until switching on In this menu the minimum running time of the external heat generator can be configured as well Minimum running time The minimum running time will allow a minimum heating time of the external heat generator The external heat generator will operate at least for this duration if a release has been given The purpose of this switching Is that the heat generator will need a certain time in order to supply any energy at all Moreover this also makes a short initializing of the heat generator unnecessary 3 9 Intermediate circuit pump The intermediate circuit pump will switch on during the operation of a circuit It is the pump of the main system Mode This indicates whether the intermediate circuit pump Is activated or deactivated Secondary required initial operation Figure 14 Feed pump menu This indicates the required secondary Initial operation of the transfer station Temperature of secondary initial operation This indicates the temperature of the secondary Initial operation of the transfer station The secondary side
17. tor is lower than the required initial operation in addition to the hysteresis of switching off Figure 12 Switching heat source menu Demand If for a certain time the required initial operation falls below the hysteresis for switching on an existing heat generator e g oil kettle will switch on Release This indicates whether the external heat generator has been switched on Figure 13 Demand heat source menu 14 External energy This indicates the available temperature of external energy generators Secondary required initial operation This indicates the current secondary required initial operation If the item Switching of generator has been set here the hysteresis for switching on as well as the hysteresis for switching off can be configured by way of confirming this item Hysteres is of switching off default 5 C The heat generator will be switched on if the temperature of the external heat generator is higher than the required initial operation in addition to this hysteresis Hysteres is of switching off default 5 C If the temperature of the external heat generator is lower than the required initial operator in addition to this hysteresis the heat generator will switch off Secondary temperature of initial operation This indicates the current secondary temperature of initial operation Time until ON If the required initial operation falls below for a certain period of time
18. ver you can set the required boiler temperature and the minimum boiler temperature here Required boiler temperature defaul t 55 C The required boiler temperature indicates which temperature measured on the upper boiler sensor should be selected to charge the boiler within a loading time or during a minimum temperature charge respectively Minimum boiler temperature default 45 C The minimum temperature shows the lower limit for the charging status of the boiler measured on the upper boiler and causes a subsequent charging if the temperature has fallen below Lower temperature This indicates the current lower boiler temperature Loading times This is to configure the loading times of the boiler 3 4 Circulation A circulation pump Is used to immediately prepare and make available the heated water in a building Figure 7 Circulation menu For this purpose the heated water in the warm water boiler is continuously circulated through the water pipe This is to prevent the water for usage from cooling off in the pipe If there is no circulation pump only cold water would be available to the user when turning on the tap Mode This indicates whether the circulation Is in operation or not Operation times The fixes operation times for the circulation pump can be set here Return temperature This indicates the return temperature of the circulation to the warm water boiler 3 5 Heating circuits A heati
Download Pdf Manuals
Related Search