ENGLISH USER MANUAL
Contents
1. output 80mV rms max input S N ratio vs max output Mic2 Mic3 gt 72dB Phono gt 70dB Line 20 22KHz 0 5dB Frequency Response Mics 20 20KHz 1 5dB Ph 1dB except for controlled attenuation of 3dB oe 20Hz to reduce rumble and feedback eli Bass 20 dB Equalizations MictiZone Al Zone B Middle 15 dB Treble 14 dB Power supply Dimension W x D x H 483 W x 200 D x 44 H mm Netweignt ess O2. AINS NO USER SERVICEABLE PARTS WARRANTY One year from date of purchase OPERATING DETERMINATIONS If this equipment is operated in any other way than those described in this manual the product may suffer damage and the warranty becomes void Incorrect operation may lead to danger e g short circuit burns electric shocks lamp failure etc Do not endanger your own safety and the safety of others Incorrect installation or use can cause serious damage to people and property Features Six lines including one phono three microphone inputs Microphone 1 is equipped with auto override sensitivity adjustment delay time EQ and gain Balanced microphone inputs on front and rear panels Front panel Channel on off switches Dual zone assignment for all inputs Two zone outputs with gain pan EQ and stereo mono selection Zones have unbalanced and balanced outputs with master gain reduction Headphone output with volume control Front panel PUSHMONO R Mr e o o o ar oromr CR 6 RACK MIXER un A 6 B b Te elim lu os Oh el e O BLE ASS MIDDLE TRI EBLE Se cs W aus O 8 u 13 Input gain knobs 6 channels Control individual source levels On off switches Allow input sources to be individually selected Zone assign Dete
3. TIWANVIN 43SN co Order Code MIXE01 www prolight da X M9 vA TV NO S S di d4 O ad d YIXIN 9 Y9 WARNING FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START UP CAUTION Keep this equipment away from rain moisture and liquids SAFETY INSTRUCTIONS Every person involved with the installation operation amp maintenance of this equipment should Be competent Follow the instructions of this manual CAUTION TAKE CARE USING THIS EQUIPMENT HIGH VOLTAGE RISK OF ELECTRIC SHOCK Before your initial start up please make sure that there is no damage caused during transportation Should there be any consult your dealer and do not use the equipment To maintain the equipment in good working condition and to ensure safe operation itis necessary for the user to follow the safety instructions and warning notes written in this manual Please note that damages caused by user modifications to this equipment are not subject to warranty IMPORTANT The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorised modification to the equipment Never let the power cable come into contact with other cables Handle the power cable and all mains voltage connections with particular caution Never remove warning or informative labels from the equipm
4. ent Do not open the equipment and do not modify the equipment Do not switch the equipment on and offin short intervals as this will reduce the system s life Only use the equipment indoors Do not expose to flammable sources liquids or gases Do not carry the unit with only one handle Always carry using both handles Always disconnect the power from the mains when equipment is not in use or before cleaning Only handle the power cable by the plug Never pull out the plug by pulling the power cable Make sure that the available voltage is between 220v 240v Make sure that the power cable is never crimped or damaged Check the equipment and the power cable periodically If the equipment is dropped or damaged disconnect the mains power supply immediately Have a qualified engineer inspect the equipment before operating again If the equipment has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation might damage the equipment Leave the equipment switched off until it has reached room temperature e If your product fails to function correctly discontinue use immediately Pack the unit securely preferably in the original packing material and return it to your Prolight dealer for service Only use fuses of same type and rating Repairs servicing and power connection must only be carried out by a qualified technician THIS UNIT CONT
5. icrophone to activate auto talkover Delay Time Changes the speed and the music inputs return to normal volume after a microphone is used The time the music takes to return to the pre set volume varies from 0 5 4 seconds Connections set up There are many options available for your individual needs and the diagram below is just one example for your reference Make sure all knobs are at zero and all devices are off First connect all input sources next connect the stereo outputs to the power amplifiers and or audio receivers such as CD players Plug your mixer into the AC power supply Now you are ready to switch everything on Important Always switch on your audio input sources such as turntables or CD players first then your mixer and finally amplifiers When turning off always reverse this operation by turning off am plifiers then your mixer and then input devices Main Balanced Balanced e Turntable 1 A El rn External Mixer W Amplifier O WAmbitier q S365 Ss G2 Sz Ss Sra Sra O a TER AE en Ese Note Incorrect connection will result in malfunction Make sure the connection is correct before operation Specifications 10k input impedance Line 140mV rms sensitivity for 1 4V balanced output 10K input impedance un balanced pu s 1 5mV rms sensitivity for 1 4V balanced output 60mV rms max input 10K input impedance Mic2 Mic3 1 5mV rms sensitivity for 1 4V balanced
6. match the optimum inputs of amplifiers Unbalanced Zone Outputs Output controlled by the Zone knobs Unbalanced Line Inputs For connection of DVD players CD players tuners or other mixing consoles Note a Plug mono audio sources into both Left and Right inputs using a Y cable connector b Line 3 can receive a turntable input depending on phono line switch position Phono Line Switch Select the appropriate position for your input device With phono selected the input signal is fed directly to the high quality RIAA phono pre amplifiers so use this input only for turntables Line level sources will overload the sensitive phono pre amps Switch this over to the Line position for line devices such as CD players and mixing consoles Ground connection Use these connections with your turntables grounding cable to avoid signal hum Combo Jack XLR connector Allows connection of either a 1 4 jack line level or an XLR microphone level depending upon switch 25 position Mic Line switch Balanced XLR input for microphones balanced Jack input for line level sources Auto Talkover Control Sets the front panel Microphone to automatically reduce other source levels when the mic is spoken into Positions are available for either 12dB and 40dB complete reduction Talkover sensitivity adjustment Determines the point in which auto override activates The more sensitive the adjustment the quieter you need to speak into your m
7. rmines which zone the audio is directed to The A B position sends audio to both Zones Microphone 1 Gain control Controls the mic volume for the Neutrik combo connector on the front panel Microphone EQ controls Adjusts the Treble Mid and Bass frequencies of the microphone inputs Neutrik Combo Connector Allows connection of either a 1 4 jack or an XLR plug Zone Knob Controls the output level Mono Stereo Selects the mode for the sound output Pan Controls the mix of stereo audio Moved to the left only the left speakers will be heard or to the right for the right speakers 10 Level Indicator Shows the level of sound output 11 Zone EQ Adjusts the Treble Mid and Bass frequencies of the zoned audio 12 Headphone Gain Control Adjusts the headphone volume 13 Headphone Jack for headphones connection A WON OONOA Features Rear view 14 30 26 27 28 14 Power supply input Insert the power adapter before switching on 16 17 18 19 Record Output Mix of output sent to either zone 21 22 23 24 25 26 27 28 Power Switch Turns the unit on and off Balanced Zone B outputs 1 4 stereo balanced 1 4 jack connectors controlled by the Zone B knob Balanced Zone A outputs Balanced stereo XLR connectors controlled by the Zone A knob Master Gain Reduction Sets the output level of the Zone A outputs from 0 245V to 2 5V to
Download Pdf Manuals
Related Search