DG-100 Split Digital Keypad Entry system Operation User's Manual
Contents
1. A Publish 2005 01 03 Page 2 3 GEM GIANNI INDUSTRIES INC Master Code reset to Factory 1234 and Delete All User Codes Insert the jumper RESET 1 2 position gt 5 audible beeps gt Reset Master Code successful gt after 3 seconds gt 5 audible beeps gt Delete All User Codes gt Return Insert the jumper to 2 3 positions 6 Wiring diagram Blue aqgaanaa F PB Power Supply z N O Ss a COM RC Fail Safe N C R Q Locking Device 5 Factory or remove all 3 stored PIN codes P Reset Master Code to Dwro ACLL Push Button aaa de aoanan Power Supply amp rsa O Lay N C P Fail Secture P lf Reset Master Code to Locking Device 2 m 2 Factory or remove all 3 E Push Button 3 stored PIN codes Reset Note The suggested wire gauge is 22 26 AWG Distance between the keypad and controller board Maximum 50 M cable 22 26 AWG The varistor or diode must be connected across the lock terminal electromagnet operated by the device The vartistor controls the overload produced by the strike coil EMP Copyright Gianni Industries Inc All Rights Reserved MI 02 DG 100 4C Ver A Publish 2005 01 03 Page 3 32. or program other operating Note 1 The codes 0000 1234 or master code are not be used for PIN code Note 2 Random user codes operate open door 5 222222222222222222222222 x x xxx j 1 random codes x x gt x 4 digit user codes Random codes and correct user codes total 29 digits To Delete a User Code Enter the Programming mode Press the slot position code of your choice to delete example 06 Press x006 0000 beep delete Press to exit from the programming mode or programming other operating To Program Relocking Timer Enter the Programming mode A Relay Press 100 Followed by the number of seconds the relay should open 05 5 seconds 01 99 seconds beep enrolled Press l to exit from the programming mode or program other operating B Enter 00 Sets the relay to latching mode Correct code entered opens the relay and the relay stays open until the correct code is entered again Changing the Master codes Enter the Programming mode Enter 000 Followed by the new 4 digit master code beep enrolled Enter to exit from the programming mode or program other operating Master Code reset to Factory 1234 Insert the jumper RESET 1 2 position gt 5 audible beeps gt Reset successful gt Return Insert the jumper to 2 3 positions Copyright Gianni Industries Inc All Rights Reserved MI 02 DG 100 4C Ver
3. GEM GIANNI INDUSTRIES INC DG 100 Split Digital Keypad Entry system Operation User s Manual 4 Codes 1 Product Characteristic Allows up to 99 PIN codes Random user codes for anti peeping Fully Programmable via keypad and master code LED display with audible indication Invalid PIN Lock out Metal die casting housing Deftly dimension for narrow jamb Non Volatile Memory With vandal resistant screws e Split of controller and reader for high security Specifications Operating Voltage 12 Vdc Current Draw Average 15mA Peak 70mA 12Vdc Relays Rated 2A MAX 30Vdc 0 4A 120Vac 2 Output N O N C Com Output free voltage contact Relay Activation Time 100 m Strike Time 1 99 seconds adjustable a Strike mode Access Timer or Latch Operating Temperature 20 70 C Ambient Humidity 5 95 relative humidity non condensing Invalid PIN Lock out The system will shut down for 60 seconds while 30 codes of incorrectly Master Codes enrolled or PIN codes attempted None beeper signal of PIN codes 4 digit codes User codes capacity 99 slots Factory Master Code 1234 keypad activations loss of power Color Beige White 3 The indicator signal chart Sound and LED indicator EPROM Non volatile memory System will retain all programs and codes after a total Distance between the keypad and controller board Maximum 50 M cable 22 26 A
4. WG Green LED Relay activated LED signal Red LED Power on stand by Yellow LED Programming mode 1 Beep Key in Effective PIN codes 2 Beeps Entering Exiting from the Program mode Sound signal 3 Beeps Data computing error gt other operation mistakes Master Code reset to Factory 1234 or remove all 5 Beeps stored user codes Copyright Gianni Industries Inc All Rights Reserved MI 02 DG 100 4C Ver A Publish 2005 01 03 Page 1 3 GEM GIANNI INDUSTRIES INC 4 Default Setting Master code 1234 Relay time 5 Pressed key delay 30 seconds Setting mode delay time 50 seconds 5 Operation Instruction Enter Program Mode 1 Compose twice the master code Factory master is 1234 2 beeps you are now in the programming mode 2 After 50 seconds if you have not entered any codes or data the system will automatically exit from the programming mode 3 After 30 wrong codes attempts at the master code the lockout facility will operate Exiting from the program mode 1 Press to exit from the programming mode 2 After 50 seconds if you have not entered any codes or data the system will automatically exit from the programming mode 3 After 30 wrong codes attempts at the master code the lockout facility will operate Add PIN codes Input 4 digit PIN codes gt beep enrolled gt repeat Press to exit from the programming mode
Download Pdf Manuals
Related Search