Installation Manual
Contents
1. Press out the entrapped air by moving your trumb toward the puncture Finishing Any excess over trim should then be trimmed off with a Stanley knife Installation_interior film doc LG Hausys Update 2010 09 06 http www lghausys com Page 6 of 19 Installation Manual interior film LG Hausys interior film Procedure for installation on Internal corner Procedure How To Preparation When LG Hausys Interior Film is applied to internal corners firstly apply primer to the corner covering at least 50mm of each surface Y This will ensure maximum adhesion A lt a Cutting and Positioning Follow the same method as for flat panels Adhesion Step 1 Apply the film from the widest section of the internal corner Using the applicator apply pressure to ensure the film does not bubble or drop Press and squeeze along the corner Step 2 When the temperatuer is under 20 C apply the film while heating it evenly Do not over heat as this could cause the film to wrinkle Step 3 Once the film is installed into the first section of the corner gently life and pull the film and apply pressure to the remaining corner section Step 4 Once installed apply pressure to the entire section using the plastic applicator especially the corner section Installation_interior film doc LG Hausys Update 2010 09 06 http www lghausys com Page 7 of 19 LG Hausys interior film Installation Manual interior film Air bu2. Strip off the release paper as per figure C Once both edges of the film are butt together press into place with the tip of your finger Once satisfied with the quality of the butt joint press down with the plastic applicator Installation_interior film doc Update 2010 09 06 Page 14 of 19 Installation Manual interior film LG Hausys interior film Installation procedure for walls 1 Application on space left joint Characteristics A Prior or installation of the LG Hausys Interior Film check the roll for damage B It is also important to check the rolls for colour match prior to installation C It is also important to install the film with any patterns embossing or textures running in the same direction Item Requirements Calcium silicate When using calcium silicate insulator or flexible insulator or flexible board boards cut with a panel saw ensuring all cut edges art smooth When joining allow a 6mm deep by 6mm wide gap between the panels Gymsum plaster board Install a kiln dried timber batten at the joins as detailed in figure B Do not join the film directly onto the edges of the plaster or gypsum board Ensure all fixing screws and nails are sealed with putty Mortar Fill all joins with PVC filler to ensure joints do not crack The walls should be smooth and free from defects Mooth out any uneven wall with a steel trowel or spatula as per figures C D and E Thoroughly wash down wall p
3. After the film is softened hold the a part with Step 2 the fingers and pull in the direction of the arrow Follow by pulling the b c d and e parts working away from the corner Ensure that enough pressure is applied to avoid any air bubbles or so that the film does not Installation_interior film doc LG Hausys Update 2010 09 06 http www lghausys com Page 10 of 19 Installation Manual interior film LG Hausys interior film crumple Step 3 To prevent the edge of the film from peeling off and shrinking ensure the film is covering 20 to 30mm of the reverse side of the panel Step 4 Cut off any excess of rolled up film with a Stanley knife Apply pressure again to the entire panel especially at the curved edge To ensure the film does not shrink from the corner apply a staple on the corner Air bubble releasing Follow the same procedure as for flat areas and finishing Installation_interior film doc LG Hausys Update 2010 09 06 http www lghausys com Page 11 of 19 Installation Manual interior film LG Hausys interior film Procedure for installation on door surfaces Flush panels and smooth doors LG Hausys Interior Film can be applied to doors either in the factory after manufacture or on the work site prior to the final installation of the door The door frame should be installed and any fitting adjustments should be made prior to applying the LG Hausys Interior Film LG
4. Hausys Interior Film can be installed whilst the door is hanging However it is easier to remove the door from the frame and lay the door flat on a working table and apply the film whilst the door is horizontal Remove any hardware such as locks handles etc and replace at the completion of work Procedure How To Preparation Step 1 Remove any dust oiliness or surface contaminants on the substrate with a lint free cloth and thinners Any surface imperfections should be removed with sandpaper Step 2 After cleaning the substrate apply primer particularly to the top and edges of the door Install as per instructions for flat areas Adhesion Flush panel Apply the film by overlapping both sides on the hm joint at the top of the door rl faa TT ERE Installation_interior film doc LG Hausys Update 2010 09 06 http www lghausys com Page 12 of 19 Installation Manual interior film LG Hausys interior film Procedure for installation on partition walls LG Hausys Interior Film can be applied to partitions either in the factory after manufacture or on the work site prior to the final installation of the partition Procedure How To Preparation Remove any dust oiliness or surface contaminants on the substrate with a lint free cloth and thinners Any surface imperfections should be removed with sandpaper Priming Apply primer to the dege joins and overlapped part of the film Installation If the film is being installed
5. apply the film to substrate with a temperature of 10 C and over Once the film is adhered to substrate press the film to the substrate while heating it with a dryer Dust and contamination It is vital that the work area is free from dust particles as should particles be Installation_interior film doc Update 2010 09 06 Page 4 of 19 Installation Manual interior film LG Hausys interior film trapped between substrate and film they will show through the surface of the film Ensuring that the work area is well it will assist in identifying any contamination or air bubbles in the surface Safety The primer and substrate sealant are combustible and inflammable and should not be used or stored near heat sparks or naked flames Work areas should be well ventilated Application table The work table or bench should be covered with corrugated paper or a blanket to ensure the interior film is not damaged Storage and handling Precautions LG Hausys Interior Film should be stored in a dry cool dark room LG Hausys Interior Film has a shelf life of one year Where possible when transporting LG Hausys Interior Film it should be top loaded to avoid damage Particular care should be taken in storage and handing in winter as the film can become hard and more susceptible to damage Procedure for installation on flat areas Procedure How To Substrate conditioning Lay the film on flat working table and measure the substrate Always cut the
6. at the work site install as detailed in figure A and B To ensure a good quality join finish apply th film by overlapping at the partition join It is important that the film is well adhered to the top section of the partition so that it does not peel off Ensure that at least 10mm of film is adhered to the top of the partition Factory installation If the film has already been applied at the factory prior to delivery to the work site simply install the partition as per figure C and D Installation_interior film doc LG Hausy p G Hausys Update 2010 09 06 http www lghausys com Page 13 of 19 LG Hausys interior film Installation Manual interior film Procedure for butt joining method Procedure Adhesion Conditioning Cutting Dust remova Release paper removal Adhesion Finishing LG Hausys http www lghausys com How To When butt joining LG Hausys Interior Film leave 50mm of the release paper on the back of the film Leave a minimum of 30mm over trim on both sides of the join so that they can be overlapped To minimize any shrinkage at the joint leave the LG Hausys Interior Film for 24hours before cutting back the over trim Place a ruler on thr center of the joint Carefully slice through both pieces of the film The knife blade should be at right angles to the film Remove the cut fragment of the film Also remove any dust from the surface of the substrate
7. film allowing for a 2 4cm over trim Positioning Start positioning by placing the film on the substrate Peel back the release paper and fold it Gently press with your thumb to gain enough adhesion to hold the film in place LG H au sy S Installation_interior film doc Update 2010 09 06 http www lghausys com Page 5 of 19 Installation Manual interior film LG Hausys interior film Adhesion Step 1 To eliminate any air bubbles under the film start in the middle of the panel With the plastic applicator apply pressure on the film to gain full adhesion Start in the middle of the panel and work your way out to the sides of the panel in each direction Hold the plastic applicator at a 45 angle to the substrate making sure you work the applicator in one direction only Step 2 Pull back the release paper 300mm at a time While pulling back the release paper apply pressure with the plastic applicator working from the top to the bottom of the panel Step 3 Once the LG Hausys Interior Film is adhered press the entire panel again with the plastic applicator working from the top of the panel to the edges Particular attention should be paid to the edge of the panels Air bubble releasing If during installation air should be trapped behind the film causing a bubble gently strip back the film and reapply with the plastic applicator Very small air bubbles can be released by pricking the bubble with a pin
8. installation precaution When two sheets of film are applied by overlapping Item Priming Embossed patterns Substrate sheet sizes Item Board sizes Substrate movement Requirements Apply the primer PM 04 on lower film and overlap the top film after a complete dry It is not possible to join embossed by dynamic patterns using the overlapping method Please contact your disitributor for further information Requirements Where possible avoid horizontal joins in the substrate and using large sheet sizes that suit the ceiling height If it is necessary to join substrate panels alternate the horizonal joint at the top and bottom as per detail To help eliminate movement in the substrate and cracking of fillers or putty ensure the joins are well nailed Direction of colour design and embossing The embossing has a delicate directional pattern Take care to install panels in the same direction as 1f they are installed in opposite directions this can give the appearance of colour variation LG Hausys http www lghausys com Installation_interior film doc Update 2010 09 06 Page 17 of 19 Installation Manual interior film LG Hausys interior film Primer application When applying the primer to installed walls apply it to prime alternated panels so that overlapping film does not become adhered to adjoining panels prior to being installed into the joins Things to be aware of during Interior Film app
9. that contain any additives Substrates such as flexible PVC PP Nylon and fluorine are especially not recommended B Remove stain with solvent C Priming is not necessary Adhere film straight away A Finish with steel trowel after joints are filled with joint material to prevent cracks B Allow it to dry for a minimum of 3 weeks C Remove stain with sandpaper or wire brush and clean the surface D Coat surface with sealer and apply putty over the whole area for better adhesion E Adhere film after complete primer dry for over 30minutes PM02 Solvent type Adhere film after complete primer dry for over 2hours PM04 Water type A Fill voids with filler and apply putty after sealer coat B Abrade the surface with sandpaper and clean with solvent C Adhere film after complete primer dry for over 30minutes PMO02 Solvent type Adhere film after complete primer dry for over 2hours PM04 Water type Substrate conditioning storage and handling Substrate Substrate conditioning Substrate conditioning LG Hausys http www lghausys com Preparation method Temperature For unprimed surfaces to gain maximum adhesion LG Hausys Interior Film should be installed to substrate with a temperature ranging between 10 C 30C __ If the substrate temperature is below 10 it should be heated by infra red ray lamp jet heater or hair dryer to ensure the correct temperature If the recommended primer is used it is possible to
10. LG Hausys interior film Installation Manual interior film Installation Manual Physical and chemical properties Test Result Within 0 8mm Length Width Property Dimensional Stability Temperature for adhesion Weather ability Abrasion Heat resistance Moisture resistance Low temperature resistance Resistance to stains Resistance to chemical 10C 30C No effect No change No change No change No change No change Solution Heptane Ethyl Alcohol Water Salt solution 5 MEK Xylene LG Hausys http www lghausys com Result No change No change No change No change Damaged Damaged Test Meathod Measuring a 100x100mm piece of film on a 150x150mm aluminum plate after 24 hours at 80 C Measuring ideal temperature range for best adhesion Measuring colour change and fading after 200 hours on weather O meter with XENON ARC lamp Measuring surface wearability by TABER abrasion tester abrasion wheel CS 17 load 1kg cycle 1 000 Measuring film adhesion to aluminium plae after 30days at 60 C Testing film adhesion to aluminium plate after 30days at 40 C and 90 relative humidity Testing film adhesion to aluminium plate after 15days at 30 T Measuring stains caused by the following liquid solutions 24 hours later after wiping out with wet cloth salt solution 1 ethanol 50 olefin oil orange juice caustic soda 10 soap solution coffee coke mil
11. b ble releasing and finishing Procedure Adhesion Step 1 Step 2 Step 3 Step 4 Air bub ble releasing and finishing LG Hausys http www lghausys com Follow the same procedure as for flat areas How To Apply the film from the widest section of the internal corner Using the applicator apply pressure to ensure the film does not bubble or drop Press and squeeze along the corner When the temperatuer is under 20 C apply the film while heating it evenly Do not over heat as this could cause the film to wrinkle Once the film is installed into the first section of the corner gently life and pull the film and apply pressure to the remaining corner section Once installed apply pressure to the entire section using the plastic applicator especially the corner section Follow the same procedure as for flat areas Installation_interior film doc Update 2010 09 06 Page 8 of 19 Installation Manual interior film LG Hausys interior film Procedure for installation on External corner treatment Procedure Preparation measuring and cutting Trimming Positioning Adhesion Step 1 Step 2 Step 3 Step 4 LG Hausys http www lghausys com Procedure O O Howo iss To Follow the same procedure as detailed for internal corners C LL EE Trim film to the desired width including the 7 corner over trim Follow the same procedure as for flat panels Appl
12. ce Physical properties Dynamic Metal film is prouced using advanced quality control however there may be some colour variation between production batches Prior to installation ensure that the colour of the substrate does not effect the colour of the film Ensure the substrate is clean and smooth so that imperfections do not show through the finished prodect Substrate preparation Substrate Wood Gymsum board Overlapped Mortar Painted Aluminum Veneer Calcium Chlorinated steel Stainless Hard Silicate board Copper steel board Asbestos Plate Plate Surface Punch nails Ensure walls Remove rust preparation are dry Sealer z 7 Sealer Sealer coating Application EP putty Moisture resistant putty Cross putty EP putty Polyester putty Putty Moisture EP putty Resistant putty Cross putty Board putty LG H au sy S Installation_interior film doc Update 2010 09 06 http www lghausys com Page 16 of 19 Installation Manual interior film LG Hausys interior film Surface Sand paper 1 Uneven welded area grinding grinder 2 Flat area sandpaper Surface Brush Alcohol thinner Cleaning Primer PMO02 Solvent type PM04 Water type Coating Dilute primer and thinner by Dilute primer and water by 1 1 on overall 1 1 on overall Use undiluted primer on edge Use undiluted primer on edge Adhere film after complete primer dry for over 2hours Adhere film after complete primer dry for over 30minutes Other
13. ial multi layer structure could make and the film s adhesive side during application the exfoliation or surface crease with application of film surface could be marred or damaged heat on the surface As the product is hard it is necessary to pay more When cutting and applying the product it is attention to finishing to ensure no loose edges by necessary to consider how to connect patterns If applying more strength to obtain visually pleasing you cut the film by the printed markings on the finish release paper it is impossible to match the patterns on different films 6 Other to Note If you intend to apply film to a substrate not covered in the specifications regarding application methods and materials MDF etc please contact the LG HAUSYS or the dealer to check application possibility You should follow the guidelines on the specifications to apply films When film is applied it is necessary to use the exclusive primer for LG Hausys Interior Film PMO02 Solvent primer PM04 Water primer Installation interior film doc L G Hau ays Update 2010 09 06 http www lghausys com Page 19 of 19
14. k vinegar Measuring the level of damage after soaking film on aluminum plate in different chemical solutions for 48hours Installation_interior film doc Update 2010 09 06 Page 1 of 19 Installation Manual interior film LG Hausys interior film Flammability Self extinguished Measuring the flammability of film on aluminum plate All LG Hausys interior films have the function of fire retardant C Adhesion Substrate After primer Measuring the adhesion strength of 25mm wide strength coating kg in film applied Lauan veneer 257 on each substrate after 1days under ambient Timber veneer 3 07 temperature Gypsum board 0 51 tensile speed 300mm min 180 peel Asbestos slate 2 07 board Melamine baked 3 07 steel sheet Aluminium sheet 257 Stainless steel ZT sheet 2T Acrylic board LOT MDF Preparation Tools and Materials F A 1 Primer PMOZ PMO4 Brush Cleaning solvent alcohol white gasoline or lacquer thinner Lint Plastic applicator Steel ruler Torch Stanley knife 45 angle Needle or pin Measuring tape 11 Hair dryer Other sandpaper putty stick sealer masking tape gloves Cleaning and preparing substrate Before installing the LG Hausys Interior Film it is important to prepare the substrate surface and follow the Installation_interior film doc LG Hausys Update 2010 09 06 http www lghausys com Page 2 of 19 Installation Manual interior film LG Hausys interior film specific in
15. lication 1 Before applying Do not forget to check out the type and condition of material MDF etc to attach films to so as to identify any parts that might cause a problem In the case of MDF a different density might cause incoherent adhesive strength and printing resistance performance It is necessary to use MDFs with consistent density It is necessary to use alcohol to remove pollutants from the surface to be sprayed and check if there is any damage to the sprayed face due to solvents If it has an uneven surface you can apply putty then finish with sandpaper Use a dust brush to remove foreign substances In case of steel plates remove any surface pollutants first with alcohol lacquer or thinners For an uneven surface apply putty then finish with sandpaper Use a dust brush to remove foreign substances Do not forget to carry out a prior inspection for any problems pattern name appearance etc for products selected by customers Film application should be done after woodwork and before painting or wallpaper hanging 2 Prior task for Surface It is necessary to finishing thoroughly with sandpaper for cross section parts which are to have film applied MDF etc In particular if the material is wood MDF PB etc the smoothness of an edge or crevice is very important Therefore you should finish the part with sandpaper or with pate treatment before proceeding any further 3 Primer Treatment During primer treatmen
16. lvent apply putty on uneven and welded areas and smooth with sandpaper C Adhere film after complete primer dry for over 30minutes PMO2 Solvent type Adhere film after complete primer dry for over 2hours PM04 Water type A Check that the surface is in good condition to avoid low adhesion and bubbling B Remove stain with solvent and apply primer C Adhere film after complete primer dry for over 30minutes PMO2 Solvent type Adhere film after complete primer dry for over 2hours PM04 Water type A Test paint type and condition for adhesion by pre applying a small piece of film on the surface B Remove stain with solvent and make sure that the surface is not damaged C Apply putty on uneven areas and smooth with sandpaper D Adhere film after complete primer dry for over 30minutes PMO02 Solvent type Adhere film after complete primer dry for over 2hours PM04 Water type Installation_interior film doc Update 2010 09 06 Page 3 of 19 Installation Manual interior film LG Hausys interior film Substrate Melamine laminates Polyester coated laminates Plastic Mortar limestone Gypsum board calcium silicate board asbestos slate Installation Preparation method A Abrade the surface with sandpaper and remove stain with solvent B Adhere film after complete primer dry for over 30minutes PMO02 Solvent type Adhere film after complete primer dry for over 2hours PM04 Water type A Aviod substrates
17. rior to installation 2 Flat joining application It is important to overlap the film at joins Joining specifications Overlapping is important as substrates such as flexible board and gypsum plaster can expand and contract Overlapping at the joins will ensure that the joins are less noticeable should panels contract 3 Installation for narrow joins If the joint between panels is under 4mm the following installation method should be used Installation_interior film doc LG Hausy p G Hausys Update 2010 09 06 http www lghausys com Page 15 of 19 Installation Manual interior film LG Hausys interior film Joining specifications As it is difficult to gain a neat narrow join it is advisable to install a joiner or moulding over the joint 4 Overlapping join applications A simple method of joining is to overlap the film 10 15mm applying primer to the lower film Installation precautions for Dynamic Metal series 1 Ensure ambient room temperature is above 12 C 2 Take care to apply the film only once as repeated repositioning of the film can cause delamination 3 Avoid installation to three dimensional curved surface as strerching of the film can cause colour and pattern variation 4 The surface of the substrate must be clean and smooth as any imperfections in the substrate may show through the high gloss metallic surface 5 Wrap the plastic applicator in a lint free cloth so that it does not scratch the surfa
18. structions for each type of substrate to ensure a high quality long lasting installation Substrate General instructions Wood products Untreated steel electro galvanized steel Aluminum stainless steel painted steel PVC laminated steel Painted substrate LG Hausys http www lghausys com Preparation method A For better adhesion and finish scuff uneven surface with sandpaper or apply putty to make it flat B It is recommened to use a good adhesion hard type putty C In case you have to cover the whole surface with putty sand it 2 to 3 times afterdry to make it flat D In case you are only touching up patches try to use putty of same colour of the substrate A Scuff the surface with sandpaper B Apply putty on uneven area and smooth with sandpaper Clean surface with solvent C Coat with the designated primer 2 or 3 times allowing to dry after each coat Adhere film after complete primer dry for over 30minutes PMO02 Solvent type Adhere film after complete primer dry for over 2hours PM04 Water type A Remove rust and stain with sandpaper first and clean the surface with solvent B Apply putty on uneven area and smooth with sand paper Wipe out with solvent C Adhere film after complete primer dry for over 30minutes PMO2 Solvent type Adhere film after complete primer dry for over 2hours PM04 Water type A Abrade uneven and welded areas with sandpaper B Remove stain with so
19. t a cross section of wood MDF PB etc tends to absorb more primer than other parts Thus spray at least 2 or 3 coats of primer Once primer is applied the next treatment should start when the previous primer has completely dried 4 How to apply Make sure to hide the cross section of the cut out film as much as possible Try not to show the substrate to be applied with film Installation interior film doc 5 LG H p GI MHES Update 2010 09 06 http www lghausys com Page 18 of 19 Installation Manual interior film LG Hausys interior film It is possible there may be some color difference between product lots so it is necessary to classify lots When surface treated product is overlapped with another product you should spray undiluted PM04 solution an exclusive water type primer for LG Hausys Interior Film then proceed after it has completely dried e In particular be careful with El REINA EL EP WOOD DP RW MXA NE SOLID RB RS patterns 5 Things to be aware of when applying specific products NATURE CRAFT HIGH GLOSS Requires Butt Joint style application Butt overlap To fully achieve gloss effect of the film surface application may exfoliate on the overlapping part you should work in a clean environment due to embossing or surface treatment layer If there are some foreign substances such as dust It is not available for curved area application as its and dirt on the substrate to apply film MDF etc spec
20. y the film from the width section bordering the external corner Do not strip off the release paper of the narrower corner section Using the applicator apply pressure to ensure the film does not bubble or drop Press and squeeze along the corner When the temperature is below 20 C apply the film while heating it evenly Do not over heat as this could cause the film to wrinkle Using the same method as for flat panels remove the release paper 200 to 300mm at a time Hold the film while applying pressure with the applicator Once installed apply pressure using the plastic applicator to the entire section especially the corners Installation_interior film doc Update 2010 09 06 Page 9 of 19 Installation Manual interior film LG Hausys interior film Air bubble releasing Follow the same procedures as for flat areas and finishing Treatment for three dimensional curved surfaces Procedure How To Preparation Once any bullnose or curved edges have been shaped and sanded apply primer to the curved surface and reverse side If the primer is easily a adsorbed by the substrate reapply the primer on the former has dried Measuring and cutting Cut the film 100mm larger than the substrate size Positioning Follow the same procedure as for flat surfaces Adhesion Step 1 Apply the film from the width section bordering the external corner Do not strip off the release paper of the narrower corner section
Download Pdf Manuals
Related Search