Design, Application and Installation Manual - Lite
Contents
1. White E8 10 Storage E3 White Wire B Limit Adjustment E5 Blue for 600 to 1 000 in A Output Level Black for 1 000 to 1 500 in Red for 1 500 to 1 800 in Input Voltage E8 E10 Unused color leads Selector Move the FLASH switch and the On Off switch to the off position Locate the output and limit adjust pots The output pot B is closest to you white and to the right of the board The limit pot C is closer to the toroidal choke blue and centered on the board Only use non conductive tools to adjust these pots Turn the output pot B all the way counterclockwise turn the limit C all the way clock wise Connect a voltmeter capable of reading up to 400 VAC rms to the output of the power supply usually by inserting the probes into the back of the molex lamp connector After ensuring that all lamp connections have been made and properly insulated connect the power supply to an appropriate grounded power outlet NOTE that all adjustments must be made with lamp connected to power supply Turn on Power Supply the lamp should be dimly lit and the voltage should read less than 280VAC 10 Adjust the voltage output and limit a Turn the output pot B all the way clockwise Slowly turn the limit C pot counter clockwise until the voltage increases to 330VAC Allow the supply to stabilize for several minutes adjust if necessary Next turn the output pot B counter clockwise to 280VAC or your desir2. S U Mny a TECHNOLOGIES no Se FLATLITE architctural and Display EEO O RO EAE O Alao Lighting CALCULATING LAMP LIFE LATLITE Lamps have an installed life that varies with the operating brilliance To calculate he replacement life for your application use the table below It is important that the system be specified to have the output voltage adjusted as noted to ensure full life characteristics WHITE LAMP for Architectural Decorative Applications Average Replacement Life Characteristics when powered from FLATLITE Power Supplies Hours Foot Lamberts Candela m2 AC 444 221 147 110 7944 177 606 260 5 86 H LAMP COLORS FLATLITE Lamps are manufactured in white and green blue E Lite Technologies offers standard color overlays in Blue Violet and Florescent Red Yellow Orange and Green Additionally the FLATLITE installation tracks are designed to enable any custom color filter to be inserted over the lamp Custom colors are available from third party manufacturers serving the theatrical lighting industry 2000 E Lite Technologies Inc potici Form FSIA IM 7 REV 12 20 00 jm SUT S il 01 imu TECHNOLOGIES nc L ATLITE System for Interior Architectural and Display EA O AO EAE O alaoo Lighting 3 Installing Mounting Track 1 Layout your installation marking the bottom or inside edge of the track location lightly in pencil 2 Cut the track to length mitering co
3. Lamp is Dim 1 Power Supply Adjustment Has the supply been properly adjusted for the lamp load Refer to installation Instructions 2 Lamp replacement required Has the lamp been operating past it s useful life Replace Lamp PROBLEM Power supply adjustments operate reversed from normal 1 Mismatch of lamp size and power supply Lamp size is beyond the range of the supply Correct position of the lamp size jumper Replace power supply with correct model PROBLEM The 280VAC operating voltage cannot be reached 1 Mismatch of lamp size and power supply Lamp size is beyond the range of the supply Correct position of the lamp size jumper Replace power supply with correct model 2 Input voltage select Input voltage jumper is in wrong position Turn off power then repeat adjustment procedure Note Problem may be in lamp crimp attachment or in distribution wiring Disconnect lamp from distribu tion wiring to troubleshoot 2000 E Lite Technologies Inc ppovcntt Met sell TPS Une Form FSIA IM 10 REV 12 20 00 om mn i Donn EEA TECHNOLOGIES no
4. Mie SMmullalccmenecsaleiietiemume Lighting 1 Cautions and Warnings IMPORTANT SAFEGUARDS When using electrical equipment basic safety precautions should always be followed including the follow Ing READ AND FOLLOW ALL SAFETY INSTRUCTIONS yV This product must be installed and serviced by licensed electrical contractors familiar with the instructions in this manual y FLATLITE lamp material is an electrical appliance operating at 280 VAC 650 Hz Do not cut or pierce without proper tools and training Disconnect from power source if damaged Not intended for use in or under water Never install in an accessible area without a protective cover to prevent access Do not install directly over an ungrounded metal surface Never wire multiple lamps in series y Always install in accordance with all applicable electrical codes y Always disconnect power from the FLATLITE system before servicing y Equipment must be mounted securely in locations and at heights where it will not be readily subject to tampering by unauthorized personnel y Use of any components not supplied with the FLATLITE system or the modification of the components supplied may cause an unsafe condition yV Do not use this equipment for other than its intended purpose y This equipment is approved and rated for connection of lamps as specified in the sys tem design section Never exceed the Total or Minimum Load Rating of any power supply SAVE THESE INSTRU
5. CTIONS 2000 E Lite Technologies Inc QOD0O00O NN Form FSIA IM 3 REV 12 20 00 jm SUT S il imu TECHNOLOGIES nc FLATLITE rhe ei EA O Mie EA AE Oa alaoo LM Lighting 2 system Design A SYSTEM COMPONENTS The FLATLITE system for Interior Architectural and Display lighting consists of the FLATLITE electro luminescent lamp in a surface mount extrusion with matching inter connect accessories and an appropriately sized and specified power supply FLATLITE Lamps 1 2 1 3 or in width Provided in 240 or 480 coils Standard colors are white or green blue standard or custom overlays available Thickness is 0 025 Encapsulation laminate is suitable for use in humid or damp locations and is UV stabilized Not recommended for direct immersion The lamp may be curved or folded within certain parameters The lamp does not generate heat in use FLATLITE lamps do not deteriorate if not illuminated At full brightness the lamp will emit 20 24 footlamberts 68 5 82 2 candela m of luminance ee oe Ny ee ee FLATLITE Surface Mounting Track 1 Supplied in 10 lengths 2 rack components include an extruded UL94V0 rated UV stabilized 3 clear PVC base and with Polycarbonate lens 4 The base has a self adhesive mounting tape for easy positioning 5 May be curved within limits perpendicular to the plane of the lamp E Lite Power Supplies 1 Supplied in 4 capacities determ
6. ES no G FLATLITE rel IMO O ANC SMmUllalccmenecsaleietiemume Lighting Model 2200A N Power Supply Adjustment Instructions 9 When using electrical equipment basic safety precautions should always be followed including the following READ AND FOLLOW ALL SAFETY INSTRUCTIONS This product must be installed and serviced by licensed electrical contractors familiar with these instructions Always install in accordance with all applicable electrical codes Always disconnect power from the FLATLITE system before servicing Use of any components not supplied with the FLATLITE system or the modification of the components supplied may cause an unsafe condition Do not use this equipment for other than its intended purpose This equipment is approved and rated for connection of lamps as specified Never exceed the Total Load Rating of any power supply E5 Completely disconnect from any Size Selector power source Remove the cover from E3 the power supply and place so the com ponents inside are accessible and the switches are facing you Confirm that the input voltage select jumper A is placed correctly for your operating voltage 110 or 220 VAC Match the power supply to the lamp size The 2200A covers three operating ranges and the proper internal connec tions must be made Locate the 4 ter minals indicated as E3 E5 E8 and E10 just in front of the toroidal choke Attach the 4 wires from the choke as follows
7. G j FLATLITE Pea IMO O Mie SMmullalccmenecsaleiietiemume Lighting Design Application and Installation Instructions This Manual is also available on line at www e lite com Exclusively for use with FLATLITE electroluminescent lamps A product of E Lite Technologies Inc Trumbull CT USA 2000 E Lite Technologies Inc pp0vcntt HT sell S Form FSIA IM REV 12 20 00 fom mn onan willl a TECHNOLOGIES ne FLATLITE The world s widest thinnest longest lightbulb system for Interior Architectural and Display Lighting TABLE OF CONTENTS 1 Cautions and Warnings 2 System Design a System Components b Power Supply Sizing c Electrical Characteristics d Load Requirements e Connected Lamp Lengths f Distribution Wiring g Calculating Replacement Life h Lamp Colors Installing mounting track Installing lamp filters and lens in track Terminating lamp Adjusting power supply a Model600 A b Model 600 B c Model 2200 A N d Model 2200 B N l Troubleshooting a For 600 A amp B Systems b For 2200 A amp B N Systems D E Lite Technologies Inc 2285 Reservoir Avenue Trumbull CT 06611 877 502 3951 203 371 2070 www e lite com 2000 E Lite Technologies Inc Form FSIA IM 2 REV 12 20 00 Page pgti q i OM ONNDOOOAH FS A A dr KR amp WN a ck Ol THe RUNGE lll FEcrNOLOGIES TECHNOLOGIES inc Se FLATLITE Architectural and Display IMO O
8. LATLITE eet et ele EEO O Mie EAE Oa alaoo LM Lighting Troubleshooting Systems with2200A N or B N Power Supplies FLATLITE systems are very reliable when properly installed However the unique nature of an electrolumi nescent lamp and the extensive safety features of the power supply require some specific troubleshooting techniques PROBLEM Lamp Does not Light 1 Check Power Supply Power Is the Supply plugged into a working outlet Provide proper input voltage and current Fuses in the Power Supply inlet connector good Replace Fuses Is the Supply on off switch set to on Switch to on 2 Check Power Supply Adjustment Has the supply been properly adjusted for the lamp load Refer to installation Instructions 3 Check Lamp Connections Is the lamp connected to the Power Supply Install Repair Connector Are the lamps wired correctly Unplug the lamp s from the power supply Measuring across the lamp leads with a digital multi meter check the following 1 Continuity Yes Short Circuit in Wiring Remove Short 2 Capacitance No Open Circuit in Wiring Repair Wiring Replace Power Supply PROBLEM Lamp Blinks or Flashes 1 Flashing Switch Is the Flash switch set to on 2 Input Voltage Select Has the supply been set for the proper input voltage Refer to installation Instructions 3 Power Supply Adjustment Has the supply been properly adjusted for the lamp load Refer to installation Instructions Replace Power Supply PROBLEM
9. acitance No Open Circuit in Wiring Repair Wiring Replace Power Supply PROBLEM Lamp Blinks or Flashes 1 Input Voltage Select Has the supply been set for the proper input voltage Refer to installation Instructions 2 Power Supply Adjustment Has the supply been properly adjusted for the lamp load Refer to installation Instructions Replace Power Supply PROBLEM Lamp is Dim 1 Power Supply Adjustment Has the supply been properly adjusted for the lamp load Refer to installation Instructions 2 Lamp replacement required Has the lamp been operating past it s useful life Replace Lamp PROBLEM Power supply adjustments operate reversed from normal 1 Mismatch of lamp size and power supply Lamp size is beyond the range of the supply Correct position of the lamp size jumper Replace power supply with correct model PROBLEM The 280VAC operating voltage cannot be reached 1 Mismatch of lamp size and power supply Lamp size is beyond the range of the supply Correct position of the lamp size jumper Replace power supply with correct model 2 Input voltage select Input voltage jumper is in wrong position Turn off power then repeat adjustment procedure Note Problem may be in lamp crimp attachment or in distribution wiring Disconnect lamp from distribu tion wiring to troubleshoot 2000 E Lite Technologies Inc ppovcntt HT sells Une Form FSIA IM 15 REV 12 20 00 fom mn Dong jill qecanevece TECHNOLOGIES ne F
10. d follow these instructions Spring Loaded terminal holder 1 Insert the Pre Terminated Leads in the lower jaw of the Crimp Tool by feeding the bare wire end throught the holes as illustrated in Figure 2 You will need to gently pull the spring loaded holder downward to allow the crimps to seat properly The U on the crimp terminals must be open to the top and the leads pulled through until the terminals are firmly seated in the jaw Twisting the wire leads together behind the upper jaw helps to maintain alignment Figure 2 2 Place lamp over terminals in lower jaw carefully align ing the scribe line in the center of the lamp with the marks on the tool as illustrated in Figure 3 Align Lamp Seite 3 Close the tool carefully being certain to maintain lamp i alignment When the crimp has been made the tool will automatically release 4 Inspect the crimp One ter minal should pierce the lamp on either side of the scribe line and should be firmly folded over Figure 4 Hold the lamp up to light ensure there is no crossing or deformation of the line by the terminal 5 Slightly angle the leads away from each other to avoid the potential for a short circuit Then insulate the crimp w the Connector Sealing Tape being certain to cover all metal components Figure 5 Allow a 24 hours for tape to cure for Figure 4 Figure 5 Figure 6 maximum effectiveness 6 Make connection to distribu tion wiring with w
11. ectrical equipment basic safety precautions should always be followed including the following READ AND FOLLOW ALL SAFETY INSTRUCTIONS This product must be installed and serviced by licensed electrical contractors familiar with these instructions Always install in accordance with all applicable electrical codes Always disconnect power from the FLATLITE system before servicing Use of any components not supplied with the FLATLITE system or the modification of the components supplied may cause an unsafe condition Do not use this equipment for other than its intended purpose This equipment is approved and rated for connection of lamps as specified Never exceed the Total Load Rating of any power supply 1 Completely disconnect from any power source Remove the cover from the power supply and place so the com Output Level ponents inside are accessible and the B switches are facing you 2 Confirm that the input voltage select jumper A is placed correctly for your operating voltage 110 or 220 VAC 3 Match the power supply to the lamp size The 600B covers two operating ranges and the proper internal selection must be made Locate the Lamp Size Jumper D Lift the white jumper straight up and re gt gt gt gt gt Lamp Size Jumper Voltage Select place to change settings for PERAE Small Lamp 250 400 in Large Lamp 400 600in 4 Locate the output and limit adjust pots Limit Adjustment The output po
12. ed output voltage Allow the system to stabilize for five minutes Then re adjust the voltage to 280VAC At this oao o TAL setting the lamp is operating at its brightest To reduce the brightness and increase the life 2000 E Lite Technologies Inc Form FSIA IM 13 REV 12 20 00 of the lamp adjust the output B lower until the output matches your ili m GUT i T f TECHNOLOGIES nc G FLATLITE rhe oi WMO O MN EAA Oa alaoo LM Lighting Model 2200B N Power Supply Adjustment Instructions When using electrical equipment basic safety precautions should always be followed including the following READ AND FOLLOW ALL SAFETY INSTRUCTIONS This product must be installed and serviced by licensed electrical contractors familiar with these instructions Always install in accordance with all applicable electrical codes Always disconnect power from the FLATLITE system before servicing Use of any components not supplied with the FLATLITE system or the modification of the components supplied may cause an unsafe condition Do not use this equipment for other than its intended purpose e This equipment is approved and rated for connection of lamps as specified Never exceed the Total Load Rating of any power supply Move the FLASH switch and the On Off switch to the off position Locate the output and limit adjust pots The output pot is closest to you white and to the right of the board The lim
13. ined by total length of installed lamp 2 UL Listed CE Compliant 3 For operation from 110 or 220VAC line voltage 4 Fuse protected inputs 5 Automatic short and open circuit protected outputs 6 Special safety circuit on certain models prevents shock hazard 2000 E Lite Technologies Inc goil 0000 tt Form FSIA IM 4 REV 12 20 00 om oomnnn S U Mny a TECHNOLOGIES no Jx FLAILITE DO E EEO O AO EAE O Alao Lighting B POWER SUPPLY SIZING To determine the proper power supply for your application use the following table Installed Length Feet Width From To 16 42 100 300 21 50 28 69 08 27 600A 69 167 21 51 600B 600A 151 2mm C ELECTRICAL CHARACTERISTICS FLATLITE lamps operate at a higher voltage and frequency than most electrical compo nents Depending upon the brightness required the E Lite power supplies will operate according to the following parameters PowerRange Input Output PS Model __ Watts 600A 600B DOOR 100 240 50 150 330 580 740 2200B 2000 E Lite Technologies Inc QOD0O00O NN Form FSIA IM 5 REV 12 20 00 fomm SUT S laniaqqqitl TECHNOLOGIES nc FLATLITE rhe ei EEO O Mie EA AE Oa alaoo LM Lighting D CALCULATING ELECTRICAL LOAD REQUIREMENTS Each square inch of FLATLITELamp draws 0 045 watts at its nominal operating brilliance To calculate the total current requirements of an installation multiply the installed length in linea
14. irenuts or crimps as required by local code Figure 7 Figure 3 Figure 7 TAL 2000 E Lite Technologies Inc pp0vcntt HT sell JTS Form FSIA IM 9 REV 12 20 00 fom mn N willl a TECHNOLOGIES nc FLATLITE rhe ei sR OOK Mie EA AE O alaoo LM Lighting 6 Attaching and Adjusting Power Supply Using the connection harness supplied with the power supply attach the distribution wiring to the power supply using wire nuts or crimps as required by local code The power supply must then be set up carefully according to the following instructions Confirm that the supply was properly sized for the total lamp installation before proceed Ing Before adjusting the power supply refer to the lamp life calculation chart on page 7 to determine the proper output voltage setting for the supply You will need the following tools Phillips screwdriver to open power supply case Non Conductive adjustment tool Voltmeter capable of reading up to 400VAC The lamp must be connected to the power supply to adjust 2000 E Lite Technologies Inc goil 0000 tt Form FSIA IM 10 REV 12 20 00 om onomat S U Mny a TECHNOLOGIES nc G FLATLITE rei E IMO CRMC SMmullaccmenecsaleiietiemume Lighting Model 600A Power Supply Adjustment Instructions When using electrical equipment basic safety precautions should always be followed including the following READ AND FOLLOW ALL SAFETY INSTRUCTIONS Thi
15. it pot is closer to the toroidal choke blue and centered on the board Only use non conductive tools to adjust these pots 6 Turn the output pot all the way counterclockwise set the limit pot at approximately the midpoint 7 Connect a voltmeter capable of reading up to 400 VAC rms to the output of the power supply usually by inserting the probes into the back of the molex lamp connector 8 After ensuring that all lamp connections have been made and properly insulated connect the power supply to an appropriate grounded power outlet NOTE that all adjustments must be made with lamp connected to power supply 9 Turn on Power Supply the lamp should be dimly lit and the voltage should read less than 280VAC 10 Adjust the voltage output and limit a Slowly turn the output pot clockwise until the meter reads at least 330VAC but not more than 350VAC If the voltage does not rise to 330VAC turn the limit pot counter clockwise 1 4 turn b Slowly turn the limit pot clockwise until the voltage decreases to 330VAC c Allow the supply to stabilize for several minutes adjust if necessary d Next turn the output pot counter clockwise to 280VAC or your desired output voltage e Allow the system to stabilize for five minutes Then re adjust the voltage to 280VAC At this setting the lamp is operating at its brightest To reduce the brightness and increase the life of the lamp adjust the output lower until the output matches your requirements
16. o Power Inlet Molex Connector 7 Connector r Toroidal Choke Limit Adjustment Output Level Adjustment i T inoi Voltage Select Jum per 2000 E Lite Technologies Inc Form FSIA IM 14 REV 12 20 00 ji m RUNGE ill ill TECHNOLOGIES no TECHNOLOGIES inc G FLATLITE rie E IMO CRMC SMmUllalccmenecsaleiietiemums Lighting Troubleshooting Systems with 600A or B Power Supplies FLATLITE systems are very reliable when properly installed However the unique nature of an electrolumi nescent lamp and the extensive safety features of the power supply require some specific troubleshooting techniques PROBLEM Lamp Does not Light 1 Check Power Supply Power Is the Supply plugged into a working outlet Provide proper input voltage and current Fuses in the Power Supply inlet connector good Replace Fuses Is the Supply on off switch set to on Switch to on 2 Check Power Supply Adjustment Has the supply been properly adjusted for the lamp load Refer to installation Instructions 3 Check Protection Circuit Is the Green Light Off Unplug and re plug supply from outlet 4 Check Lamp Connections Is the lamp connected to the Power Supply Install Repair Connector Are the lamps wired correctly Unplug the lamp s from the power supply Measuring across the lamp leads with a digital multi meter check the following 1 Continuity Yes Short Circuit in Wiring Remove Short 2 Cap
17. r feet by the factor below divide that amount by the line voltage to obtain amperes 1 2 x0 27 3 x1 62 1 x0 54 6 x3 24 Example 100 of 1 Lamp at 110VAC 100 0 54 54 watts 54 110 49 amperes E CONNECTED LAMP LENGTHS Uninterrupted continuous runs of lamp can be made in the following maximum lengths to the capacity of the power supply 1 2 350 37150 1 300 6 100 Multiple lamps can be operated in parallel or daisy chained to the capacity of the power supply F POWER SUPPLY DISTRIBUTION Minimum 18 gauge 300VAC rated stranded copper wire is recommended for distribution wiring when installing the FLATLITE system Due to the operating voltage of the lamp the power supply can be located at a relatively long distance from the lamp itself Less than 100 for any of the lamps will not effect the output To calculate the amount of voltage drop in your system using 18ga wire use the data from the ELECTRICAL CHARACTERISTICS table and the following formula voltage drop 2mps x length of wire in feet x 00651 output voltage a drop of 5 or less will not have a noticeable effect on the output of the lamp Increasing the size of the distribution wiring will enable longer distribution runs NOTE Your local electrical codes govern the use of conduit plenum rated sheathing and other installation requirements 2000 E Lite Technologies Inc goil 0000 tt Form FSIA IM 6 REV 12 20 00 om oomnnn
18. rners 3 Remove the protective tape to expose the self adhesive strip 4 Apply Track to wall following line 5 Attach Track securely to surface as necessary by drilling and countersinking holes and using flat head screws not provided 6 Using Track as a guide cut clear lens to length allowing butt joints at corners 7 At service end install surface mount plastic junction box as illustrated below 4 Installing Lamp in Track 1 Starting from service end leave several inches of lamp inside box 2 Slide or flex lamp into track metallic foil side to track making corners as shown below To make a 90 right turn oe 1 Fold end of lamp under to make 90 turn exposing the back of the lamp 2 Fold toward yourself to complete bend exposing face of lamp again NOTE Do not crimp or tightly compress Face of lamp 5 corner Repeated bending or flexing at the same point will damage lamp 3 At end of track cut lamp with scissors to fit and insulate exposed end by covering completely with end sealing tape 4 Slide or flex color filters into track over lamp if desired 5 Slide or flex clear lens into track over lamp 2000 E Lite Technologies Inc goil 0000 HL Form FSIA IM 8 REV 12 20 00 on S U Dooni EEEN TECHNOLOGIES inc G 3 FLATLITE re EEO O KAO SMmUllalccmenecsaleiietiemume Lighting 5 Terminating Lamp and Making Electrical Connections Carefully read an
19. s product must be installed and serviced by licensed electrical contractors familiar with these instructions Always install in accordance with all applicable electrical codes Always disconnect power from the FLATLITE system before servicing Use of any components not supplied with the FLATLITE system or the modification of the components supplied may cause an unsafe condition Do not use this equipment for other than its intended purpose This equipment is approved and rated for connection of lamps as specified Never exceed the Total Load Rating of any power supply 1 Completely disconnect from any power source Remove the cover from the power supply and place so the com ponents inside are accessible and the switches are facing you Output Level 2 Confirm that the input voltage select B jumper A is placed correctly for your operating voltage 110 or 220 VAC 3 Match the power supply to the lamp size The 600B covers two operating ranges and the proper internal selection must be made Locate the Lamp Size Jumper D Lift the white jumper straight up and re place to change settings for gt gt gt gt Voltage Select Small Lamp 100 150 in Jumper A Large Lamp 150 250in 4 Locate the output and limit adjust pots The output pot B is white and to the edge of the board The limit pot C is ae blue and centered on the board Only Limit use non conductive tools to adjust these pots 5 Turn
20. t B is white and to the C edge of the board The limit pot C is blue and centered on the board Only use non conductive tools to adjust these pots 5 Turn the output pot B all the way counterclockwise turn the limit C all the way clock wise 6 Connect a voltmeter capable of reading up to 400 VAC rms to the output of the power supply usually by inserting the probes into the back of the molex lamp connector 7 After ensuring that all lamp connections have been made and properly insulated connect the power supply to an appropriate grounded power outlet NOTE that all adjustments must be made with lamp connected to power supply 9 Turn on Power Supply the lamp should be dimly lit and the voltage should read less than 280VAC 10 Adjust the voltage output and limit a Turn the output pot B all the way clockwise b Slowly turn the limit C pot counter clockwise until the voltage increases to 330VAC C Allow the supply to stabilize for several minutes adjust if necessary d Next turn the output pot B counter clockwise to 280VAC or your desired output voltage e Allow the system to stabilize for five minutes Then re adjust the voltage to 280VAC At this setting the lamp is operating at its brightest To reduce the brightness and increase the life of the lamp adjust the output B lower until the output matches your eee 2000 E Lite Technologies Inc Wl Form FSIA IM 12 REV 12 20 00 qm S U UE inn it TECHNOLOGI
21. the output pot B all the way counterclockwise turn the limit C all the way clock wise 6 Connect a voltmeter capable of reading up to 400 VAC rms to the output of the power supply usually by inserting the probes into the back of the molex lamp connector 7 After ensuring that all lamp connections have been made and properly insulated connect the power supply to an appropriate grounded power outlet NOTE that all adjustments must be made with lamp connected to power supply 9 Turn on Power Supply the lamp should be dimly lit and the voltage should read less than 280VAC 10 Adjust the voltage output and limit a Turn the output pot B all the way clockwise b Slowly turn the limit C pot counter clockwise until the voltage increases to 330VAC C Allow the supply to stabilize for several minutes adjust if necessary d Next turn the output pot B counter clockwise to 280VAC or your desired output voltage e Allow the system to stabilize for five minutes Then re adjust the voltage to 280VAC At this setting the lamp is operating at its brightest To reduce the brightness and increase the life of the lamp adjust the output B lower until the output matches your al 2000 E Lite Technologies Inc pponcnl HT sell JTS Une Form FSIA IM 11 REV 12 20 00 fom 0000 Nn willl a TECHNOLOGIES no i FLATLITE rhe ei WMO CRAIC EA AE O alaoo LM Lighting Model 600B Power Supply Adjustment Instructions When using el
Download Pdf Manuals
Related Search