USER MANUAL
Contents
1. Xterior 24 Quad Xterior 36 Tri Xterior 60 CW WW Order code LEDJ157 Order code LEDJ158 Order code LEDJ159 USER MANUAL Xterior Series Safety WARNING FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START UP CAUTION INPUT VOLTAGE OF 110 240V SAFETY INSTRUCTIONS Every person involved with the installation operation amp maintenance of this equipment should Be competent Follow the instructions of this manual CAUTION TAKE CARE USING THIS EQUIPMENT HIGH VOLTAGE RISK OF ELECTRIC SHOCK Before your initial start up please make sure that there is no damage caused during transportation Should there be any consult your dealer and do not use the equipment To maintain the equipment in good working condition and to ensure safe operation it is necessary for the user to follow the safety instructions and warning notes written in this manual Please note that damages caused by user modifications to this equipment are not subject to warranty Xterior Series Safety IMPORTANT The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorised modification to the equipment e Never let the power cable come into contact with other cables Handle the power cable and all mains voltage connections with particular caution e Never remove warning or informative labels from the e2. s to flash on and off to change the flash frequency use the and buttons The SP button is used to set the run speed this button is available only in the colour change or colour fade modes To change the speed use the and buttons The D button is used to set the LED s into DMX mode See DMX value table The SA button is used to set the LED s into sound activated mode This function is unavailable on the Exterior Spectra Series The SL button is used to set the LED s into slave mode The S 0 1 2 3 4 5 6 7 8 and 9 buttons are used to set the DMX address for the LED s see example below The R G and B buttons are used to set the brightness for the LEDs to change the brightness use the and buttons DMX Address Examples To set the DMX address 245 1 Press the S button so the red LED s come on this means you can now start to set the DMX address 2 Press the 2 button so the green LED s come on this means the first digit 2 the hundreds place setting is successful 3 Now Press the 4 button and the blue LED s will come on this now means that the second digit 4 tens place setting is successful 4 Now Press the 5 button and all of the R G B LED s will come on this means that the final digit 5 units pla
3. DMX compliant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned to a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain DATA Cable DMX cable requirements for DMX operation e The Xterior Series can be controlled via DMX 512 protocol The DMX address is set on the back of the unit or via specific I R remote sold separately Your fixture and your DMX controller re quire a 3 pin connector for data input output Special Note Line termination e When longer runs of cable are used you may need to use a DMX terminator on the last unit to avoid erratic behaviour LEDJ260 13 Xterior Series Optional Cables amp I R Remotes IP Rated Power Cables IP Rated DMX Cables LEDJ137 1M LEDJ141 1M LEDJ138 2M LEDJ142 2M LEDJ139 5M LEDJ143 5M LEDJ140 10M LEDJ144 10M Interior to Exterior DMX cable Exterior Interior DMX Cable LEDJ91 1M LEDJ92 1M Optional I R Remotes LEDJ90B RGB LEDJ90C RGBW A LEDJ90D CW WW For LEDJ157 For LEDJ158 For LEDJ159 14 WWW PROLIGHT CO UK
4. desired flash value and adjust by using the UP and DOWN buttons Speed values 00 99 00 slow 99 fast Flash values 00 99 00 slow 99 fast Programme 1 Static colour In this mode you can set the Xterior 36 Tri to any colour and any brightness When you are in the 01 STATIC mode press the enter button to change the brightness of each individual colour The R represents Red G Green B Blue and F strobe The two digits after it are the brightness 00 to 99 or in CF they are the strobe speed Example If you set R G and B all to zero the 36 Tri will have no LEDs showing blackout If you set R to 99 and G and B to zero the 36 Tri will be 100 Red Programme 2 7 colour change In this mode the Xterior 36 Tri will run through its 7 preset colours Programme 3 3 colour change In this mode the Xterior 36 Tri will run through its 3 colours Programme 4 colour fade In this mode the Xterior 36 Tri will fade through its 7 preset colours DMX mode To activate the unit in DMX mode press the MODE button to show DMX MODE on the LCD screen Press the ENTER button and select the desired DMX address setting by using the UP and DOWN buttons Then to select one of the 3 DMX modes 3 5 or 6 channel press the ENTER button again to choose the desired DMX mode by using the UP and DOWN buttons For the 3 5 or 6 channel D
5. 0 x 325mm e Weight 8 5Kgs Xterior 60 CW WW e 60 x 3W LEDs CW 36 WW 24 Beam angle 30 degrees e 400Hz refresh rate e 0 100 dimming and variable strobe e DMX channels 2 or 5 selectable e Static colour dimming master slave and DMX modes e Optional I R remote LEDJ90D e 4 push button menu with LCD diaplay IP rated power in out sockets e IP rated 3 pin DMX in out sockets e Power consumption 188W e Power supply 100 240V 50 60Hz IP rating IP 65 e Dimensions 320 x 140 x 325mm e Weight 8 2Kgs The Xterior Series are DMX 512 controllable units made up of high efficiency LEDs and will operate in stand alone master slave or DMX control modes NOTE Each unit has a password and locks after being unused for several minutes to unlock the unit again press the buttons in the following order UP DOWN UP DOWN followed by ENTER Xterior Series Operation Modes Xterior 24 Quad Operation modes Built in programmes To activate the units built in programmes press the MODE button to show 01 STATIC on the LCD screen Press the ENTER button to choose between the 5 built in programmes by using the UP and DOWN buttons Now press the ENTER button to select the desired speed and adjust by using the UP and DOWN buttons Press the ENTER button once more to select the desired flash value and adjust by using the UP and DOWN buttons Sp
6. MX address information please see page 5 NOTE Once the desired settings have been selected in each of the above modes ALWAYS confirm the settings by pressing the ENTER button Slave mode To activate the unit in slave mode first you must link multiple units together and press the MODE button to show SLAVE MODE on the LCD screen Now on the master unit press the MODE button to select the desired mode and the slave units will now run in sequence with the master unit Xterior Series DMX Programme Charts Xterior 36 Tri DMX Charts 3 channel mode DMX chart Valu 0 255 Function Red 0 100 Green 0 100 0 255 Blue 0 100 5 channel mode DMX chart vato Function 0 255 0 255 Green 0 255 Blue 0 255 Master dimmer 0 100 O O ES 1 5 6 10 11 255 Strobe slow to fast 6 channel mode DMX chart Value Function O 0 255 Master dimmer 0 100 0 255 Strobe slow to fast 0 255 0 255 0 4 On 5 125 Colour change slow to fast 126 255 Colour fade slow to fast Xterior Series DMX Programme Charts Xterior 36 Tri L R Remote functions I R Remote purchased separately LEDJ90B Functions The BLACKOUT button is used to set the LED s into the power on or off modes The AR button is used to set the LED s into the auto run mode The S PR button is used to set the LED s to run the built in programmes The FL button is used to set the LED
7. ce setting is successful and the full DMX address setting has been changed 5 Now press the DMX MODE button to save the new address into memory To set the DMX address 002 1 Press the S button so the red LED s come on this means you can now start to set the DMX address 2 Press the 0 button so the green LED s come on this means the first digit Q the hundreds place setting is successful 3 Now Press the 0 button and the blue LED s will come on this now means that the second digit 0 tens place setting is successful 4 Now Press the 2 button and all of the R G B LED s will come on this means that the final digit 2 units place setting is successful and the full DMX address setting has been changed 5 Now press the DMX MODE button to save the new address into memory Important notes e Set the DMX address on each fixture before plugging into the DMX controller e The I R Remote is not usable when the fixture s are being controlled by a DMX controller e The maximum transmitter distance is 10M Please make sure that you have the I R remote aimed directly at each fixture to be programmed e If you do not press the DMX MODE button after you have changed the DMX address when you power down the fixture it will lose the address you have set 9 Xterior Series Operation Modes Xterior 60 CW WW Operation modes Built in colour temperature macro mode I
8. digit 0 the hundreds place setting is successful 3 Now Press the 0 button and the blue LEDs will come on this now means that the second digit 0 tens place setting is successful 4 Now Press the 2 button and all of the R G B A W LEDs will come on this means that the final digit 2 units place setting is successful and the full DMX address setting has been changed 5 Now press the DMX MODE button to save the new address into memory Important notes e Set the DMX address on each fixture before plugging into the DMX controller e The I R Remote is not usable when the fixture s are being controlled by a DMX controller e The maximum transmitter distance is 10M Please make sure that you have the LR remote aimed directly at each fixture to be programmed e If you do not press the DMX MODE button after you have changed the DMX address when you power down the fixture it will lose the address you have set 6 Xterior Series Operation Modes Xterior 36 Tri Operation modes Built in programmes To activate the units built in programmes press the MODE button to show 01 STATIC on the LCD screen Press the ENTER button to choose between the 5 built in programmes by using the UP and DOWN buttons Now press the ENTER button to select the desired speed and adjust by using the UP and DOWN buttons Press the ENTER button once more to select the
9. ectric shocks lamp failure etc Do not endanger your own safety and the safety of others Incorrect installation or use can cause serious damage to people and property Xterior Series Introduction Introduction Xterior 24 Quad e 24 x 8W quad colour LEDs e Beam angle 25 degrees e 400Hz refresh rate e 0 100 dimming and variable strobe e DMX channels 4 6 or 7 selectable e Static colour colour fade colour change master slave and DMX modes e Optional I R remote LEDJ90C 4 push button menu with LCD diaplay IP rated power in out sockets e IP rated 3 pin DMX in out sockets e Power consumption 204W e Power supply 100 240V 50 60Hz IP rating IP 65 e Dimensions 320 x 140 x 325mm e Weight 8 4Kgs Overview Identification 1 Tightening Knobs 2 Bracket 3 Power in 4 DMX in 5 DMX out 6 Power out 7 Mode button 8 Enter button 9 Up button 10 Down button 11 LCD display Setup Operating Instructions Xterior 36 Tri e 36 x 3W tri colour LEDs e Beam angle 25 degrees e 400Hz refresh rate e 0 100 dimming and variable strobe e DMX channels 3 5 or 6 selectable e Static colour colour fade colour change master slave and DMX modes e Optional I R remote LEDJ90B e 4 push button menu with LCD diaplay IP rated power in out sockets e IP rated 3 pin DMX in out sockets e Power consumption 172W e Power supply 100 240V 50 60Hz e IP rating IP 65 e Dimensions 320 x 14
10. eed values 00 99 00 slow 99 fast Flash values 00 99 00 slow 99 fast Programme 1 Static colour In this mode you can set the Xterior 24 Quad to any colour and any brightness When you are in the 01 STATIC mode press the enter button to change the brightness of each individual colour The R represents Red G Green B Blue W White and F strobe The two digits after it are the brightness 00 to 99 or in CF they are the strobe speed Example If you set R G B and W all to zero the 24 Quad will have no LEDs showing blackout If you set R to 99 and G B and W to zero the 24 Quad will be 100 Red Programme 2 15 colour change In this mode the Xterior 24 Quad will run through its 15 preset colours Programme 3 4 colour change In this mode the Xterior 24 Quad will run through its 4 colours Programme 4 colour fade In this mode the Xterior 24 Quad will fade through its 15 preset colours DMX mode To activate the unit in DMX mode press the MODE button to show DMX MODE on the LCD screen Press the ENTER button and select the desired DMX address setting by using the UP and DOWN buttons Then to select one of the 3 DMX modes 4 6 or 7 channel press the ENTER button again to choose the desired DMX mode by using the UP and DOWN buttons For the 4 6 or 7 channel DMX address information please see page 5 NOTE O
11. n this mode you can choose from its 17 preset built in colour temperature colour macros Simply press the MODE button to show PRESET MODE Now press the ENTER button and use the UP and DOWN buttons to choose your desired colour temperature To add flash press the ENTER button again and use the UP and DOWN buttons to set the speed from 00 99 Flash value 00 Off 99 Fast Dimming Mode In this mode you can set both of the Cool White LEDs and Warm White LEDs brightness individually Press the MODE button to show DIMMING Now press the ENTER button and use the UP and DOWN buttons to adjust the brightness of Cool White CW from 00 99 and press the ENTER button again to adjust the brightness of the Warm White WW LEDs from 00 99 To add flash press the ENTER button again and use the UP and DOWN buttons to set the speed from 00 99 Cool White values 00 Off 99 Full on Warm White Values 00 Off 99 Full on Flash value 00 Off 99 Fast DMX mode To activate the unit in DMX mode press the MODE button to show DMX MODE on the LCD screen Press the ENTER button and select the desired DMX address setting by using the UP and DOWN buttons Then to select one of the 2 DMX modes 2 or 5 channel press the ENTER button again to choose the desired DMX mode by using the UP and DOWN buttons For
12. nce the desired settings have been selected in each of the above modes ALWAYS confirm the settings by pressing the ENTER button Slave mode To activate the unit in slave mode first you must link multiple units together and press the MODE button to show SLAVE MODE on the LCD screen Now on the master unit press the MODE button to select the desired mode and the slave units will now run in sequence with the master unit Xterior Series DMX Programme Charts Xterior 24 Quad DMX Charts 4 channel mode DMX chart Red 0 100 Green 0 100 0 255 White 0 100 6 channel mode DMX chart Master dimmer 0 100 Strobe slow to fast Blue Static colour change slow to fast 126 255 Colour fade slow to fast Xterior Series DMX Programme Charts Xterior 24 I R Remote functions I R Remote purchased separately LEDJ90C Functions The BLACKOUT button is used to set the LEDs into the power on or off modes The S PR button is used to run the built in programmes To go though the built in programmes press the and buttons The FL button is used to set the LEDs to flash on and off to change the flash frequency use the and buttons The SP button is used to set the run speed this button is available only in the colour change or colour fade modes To change the speed use the and buttons The D button is used to set the LEDs in
13. place setting is successful 4 Now Press the 2 button and all of the Cool and Warm White LEDs will come on this means that the final digit 2 units place setting is successful and the full DMX address setting has been changed 5 Now press the DMX MODE button to save the new address into memory Important notes e Set the DMX address on each fixture before plugging into the DMX controller e The I R Remote is not usable when the fixture s are being controlled by a DMX controller e The maximum transmitter distance is 10M Please make sure that you have the LR remote aimed directly at each fixture to be programmed If you do not press the DMX MODE button after you have changed the DMX address when you power down the fixture it will lose the address you have set Xterior Series DMX Set Up DMX Set Up DMX 512 e DMX Digital Multiplex is a universal protocol used as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions form the controller to the fixture DMX data is sent as serial data that travels from fixture to fixture via the DATA IN and DATA OUT XLR terminals located on all DMX fixtures most controllers only have a data out terminal DMX Linking e DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are
14. quipment e Do not open the equipment and do not modify the equipment e Do not connect this equipment to a dimmer pack e Do not switch the equipment on and off in short intervals as this will reduce the system s life e Do not expose to flammable sources or gases e Always disconnect the power from the mains when equipment is not in use or before cleaning Only handle the power cable by the plug Never pull out the plug by pulling the power cable e Make sure that the available voltage is between 220v 240v e Make sure that the power cable is never crimped or damaged Check the equipment and the power cable periodically e If the equipment is dropped or damaged disconnect the mains power supply immediately Have a qualified engineer inspect the equipment before operating again e If your product fails to function correctly discontinue use immediately Pack the unit securely preferably in the original packing material and return it to your Prolight dealer for service e Only use fuses of same type and rating e Repairs servicing and power connection must only be carried out by a qualified technician THIS UNIT CONTAINS NO USER SERVICEABLE PARTS e WARRANTY One year from date of purchase OPERATING DETERMINATIONS If this equipment is operated in any other way than those described in this manual the product may suffer damage and the warranty becomes void Incorrect operation may lead to danger e g short circuit burns el
15. s are used to set the brightness for the Cool White LEDs to change the brightness use the and buttons The WW 25 50 75 and 100 buttons are used to set the brightness for the Warm White LEDs to change the brightness use the and buttons DMX Address Examples To set the DMX address 245 1 Press the S button so the Cool White LEDs come on this means you can now start to set the DMX address 2 Press the 2 button so the Warm White LEDs come on this means the first digit 2 the hundreds place setting is successful 3 Now Press the 4 button and the Cool White LEDs will come on this now means that the second digit 4 tens place setting is successful 4 Now Press the 5 button and all of the Cool and Warm White LEDs will come on this means that the final digit 5 units place setting is successful and the full DMX address setting has been changed 5 Now press the DMX MODE button to save the new address into memory To set the DMX address 002 1 Press the S button so the Cool White LEDs come on this means you can now start to set the DMX address 2 Press the 0 button so the Warm White LEDs come on this means the first digit 0 the hundreds place setting is successful 3 Now Press the 0 button and the Cool White LEDs will come on this now means that the second digit 0 tens
16. the 2 or 5 channel DMX address information please see page 5 NOTE Once the desired settings have been selected in each of the above modes ALWAYS confirm the settings by pressing the ENTER button Slave mode To activate the unit in slave mode first you must link multiple units together and press the MODE button to show SLAVE MODE on the LCD screen Now on the master unit press the MODE button to select the desired mode and the slave units will now run in sequence with the master unit Xterior 60 CW WW DMX Charts 2 channel mode DMX chart A 0 255 Cool White 0 100 0 255 Warm White 0 100 5 channel mode DMX chart 0 255 Cool White Warm White 0 255 Strobe slow to fast 0 255 Colour temperature macros 11 Xterior Series DMX Programme Charts Xterior 60 CW WW LR Remote functions I R Remote purchased separately LEDJ90D Functions The BLACKOUT button is used to set the LEDs into the power on or off modes The D button is used to set the LEDs into DMX mode See DMX value table The FL button is used to set the LEDs to flash on and off to change the flash frequency use the and buttons The SL button is used to set the LEDs into slave mode The S 0 1 2 3 4 5 6 7 8 and 9 buttons are used to set the DMX address for the LED s The CW 50 75 and 100 button
17. to DMX mode See DMX value table The SA button is used to set the LEDs into sound activated mode The SL button is used to set the LEDs into slave mode The S 0 1 2 3 4 5 6 7 8 and 9 buttons are used to set the DMX address for the LED s The R G B and A W buttons are used to set the brightness for the Red Green Blue and Amber White LEDs to change the brightness use the and buttons DMX Address Examples To set the DMX address 245 1 Press the S button so the red LEDs come on this means you can now start to set the DMX address 2 Press the 2 button so the green LEDs come on this means the first digit 2 the hundreds place setting is successful 3 Now Press the 4 button and the blue LEDs will come on this now means that the second digit 4 tens place setting is successful 4 Now Press the 5 button and all of the R G B AW LEDs will come on this means that the final digit 5 units place setting is successful and the full DMX address setting has been changed 5 Now press the DMX MODE button to save the new address into memory To set the DMX address 002 1 Press the S button so the red LEDs come on this means you can now start to set the DMX address 2 Press the 0 button so the green LEDs come on this means the first
Download Pdf Manuals
Related Search