USER'S MANUAL - largeformatsupport.co.uk
Contents
1. Place the film on the upper laminating roller adhesive side facing towards you Introduce a self locking axle Item 1 inside the mandrel of the film reel Place the assembly on the position C of the machine Centre the reel with the rules marked on the axle Introduce a self locking axle Item 1 inside the cardboard tube to recover the base paper of film Place the assembly on the position D of the machine D is not part of S 1080 Pass the film and its base paper under the lower tension bar Item 11 Separate the film from its base paper Stick the base paper on the cardboard tube with the reel pisto Item 23 Stick the lower adhesive film on the upper adhesive film by passing under the lower tension bar Place the safety cover Item 2 and the working table Item 3 S1600 Reinitialize the machine with the pushbutton located under the table on the right To operate the machine the wor king table and the safety cover should be placed on the machine Insert the feeding plate Item 22 bet ween the rollers 6 4 Adjust the rollers on the pressure posi tion 1 see chapter 3 Press 4 h in speed mode and guide the feeding plate through until it comes out on the other side Press stop k Cut the film with a2. The rollers come to a stop Unlock the buttons press up Use same method for the second emergency stop button CONDITIONING OF FILM REEL Emergency stop button Long term The reels should be stored upright in their original packing in a room free from dust and unaffected by variations in humidity and temperature Short term The reels can be left on the self locking axle and placed on the supports of the support unit A NEVER LAY THE FILM REELS ON THE FLOOR RISK OF DEFORMATION INCIDENTS PROBLEMS POSSIBLE CAUSES ACTION The lamination of the document fails or is only partly successfull The temperature is too low Increase the temperature by 10 wait 10 minutes and carry out another test The document has a silicone laquer Check the document Some film or adhesive sticks on the rollers Clean the rollers The document is too humid PROBLEMS POSSIBLE CAUSES ACTION The document beco mes warped or folded during the lamination The document fed in too rapidly The document left too long next to heating for rollers The document wasn t flat when loaded The paper is too light or too humid a Hold the document more firmly when fee ding into machine b Lower the temperature slightly c Increase the speed of rollers d Use the ventilators There are lengthwise
3. inside the cardboard tube used to recover the film base paper Place the assembly on the position B of the machine Centre the reel with the rules marked on the axle Pass the film and its base paper behind the upper tension bar Item 10 Separate the film from its base paper Stick the protective paper on the card board tube with the reel pistol Item 23 Introduce a self locking axle Item 1 inside the mandrel of the paper reel not supplied in the start up kit A The paper reel should be wider than the film reel Place the assembly on the position C of the machine Centre the reel with the rules marked on the axle Stick the paper on the adhesive film by passing under the lower tension bar Item 11 Place the safety cover Rep 2 and the working table Item 3 1600 Reinitialize the machine with the pushbutton located under the table on the right To operate the laminating machine the working table and the safety cover should be placed on the machine 6 2 Insert the feeding plate Item 22 bet ween the rollers Adjust the rollers on the pressure posi tion 1 see chapter 3 Press O in speed mode and guide the plate through until it comes out on the other side Press the button stop G k Cut the film with the safety
4. Directiva m quina 98 37 CEE 35 410 NOUVOITOU Directiva baja tensi n 73 23 CEE seg n la FRANCE norma EN 60204 1 1997 Declara que el producto siguiente dde N Directiva Compatibilidad Electromagn tica M quina modelo SIROCCO est en conformidad 89 336 CEE seg n las normas EN 55014 con las exigencias siguientes Edici n 1993 y EN 55014 2 Siempre en pos del mayor progreso nos reservamos el derecho de modificar sin aviso previo las caracter sticas y los equipos t cnicos de los modelos Garantie Votre Sirocco est garantie contre tous defauts de mat riaux et de fabrication pendant une p riode d un an apr s la date d achat En cas de d fauts de mat riaux ou de fabrication la soci t ayant vendu l appa reil r parera celui ci dans ses ateliers ou le retournera au fabricant II n existe aucune garantie autre que celle qui vient d tre mentionn e ci dessus Cette garantie ne couvre pas les dommages particuliers ou r sultants de causes indirectes qu ils soient ou non pr visibles La garantie ne couvre pas les mauvaises utilisations de la machine Warranty Your Sirocco is guaranteed against all defects of mate rials and manufacturing for a period of one year from the date of purchase In the event of defects of materi als or manufacturing the company which sold the instrument will repair it or it will be returned to the manufacturer There is no warranty other than the one mentioned above Thi
5. folds on the plastic film The tension of the film is too weak a Tighten the reel chuck brake until folds disap pear b Check loading of the rollers c Check there are not adhesive marks from the rollers Appearance of bub bles on the document The humid document is Warping or moir effect on surface The temperature is too high a Reduce the temperatu re and or increase the speed b Use the ventilators Regular appearance of bubble or pockets Adhesive stuck on the rollers a If the problem arises every 170 mm check the heating rollers b If the problem arises every 125 mm check the laminator rollers PROBLEMS POSSIBLE CAUSES ACTION Darkened document Evaporation of the sol vent from ink on docu a Laminate the dark area in last 12 13 ment b Increase the speed and slide the document in the rollers without hol ding back The document rolls up towards the top The tension is too high on the upper film The tension of the lower and upper films should be practically identical The document rolls up towards the bottom The tension is too high on the lower film The tension of the lower and upper films should be practically identical MAINTENANCE The user maintenance is limited to the regular maintenance of the objects of the paragaph 11
6. 19 20 21 Ejes autoblocantes C rter de protecci n plexigl s Mesa de trabajo Tope laterale Cesto soporte documento Cubierta izquierda Cubierta derecha Pufio superior de ajuste de la tensi n de las peliculas Pufio inferior de ajuste de la tensi n de las peliculas Rodillos laminadores superior Rodillos laminadores inferior Barra de tensi n superior Barra de tensi n inferior Rodillos calentadores superior Rodillos calentadores inferior Bot n de parada de emergencia Cuadro de mandos Lados del soporte Tabique del soporte Ruedecillas Interruptor Marcha Parada Componenti della plastificatrice selbstblockierende Auf bzw Abwickelachsen Schutzabdeckung aus PlexiglasPaniers support Anlegetisch Seitenanschlag Dokumentenhalter Abdeckung links Abdeckung rechts Einstellknopf obere Folien spannung Einstellknopf untere Folien spannung obere Laminatorwalze untere Laminatorwalze obere Spannleiste untere Spannleiste oberer Heizzylinder unterer Heizzylinder Notausschalter Ber hrungsfeld Steuerpult Untergestell Seitenteile Untergestell Mittelteil Laufrollen Ein Ausschalter 0 400 B ON 10 11 12 13 14 15 16 17 18 19 20 21 Rif Descrizione Assi autobloccanti Carter di protezione plexiglas Piano di alimentazione Arresto laterale Vassoi supporto documento Calotta sinistra Calotta destra Manopola superiore di regola zione della tensione dei film Manopola infe
7. C of the machine Lock the lower axle with the blocking ring see chapters n 6 5 A Centre the reel with the rules marked on the axle Stick the lower adhesive film on the upper film by passing in front of the lower tension bar A The double sided film should be placed in front of the tension bar For the reel of adhesive film with protective paper Introduce a self locking axle Item 1 inside the mandrel of the film reel Place the assembly on the position C of the machine Centre the reel with the rules marked on the axle Introduce a self locking axle Item 1 inside the cardboard tube to reco ver the base paper of film Place the assembly on the position D of the machine Pass the film and its base paper under the lower tension bar Item 11 Stick the base paper on the card board tube with the reel pistol Item 23 Stick the lower adhesive film on the upper adhesive film by passing under the lower tension bar Place the safety cover Item 2 and the working table Item 3 1600 Reinitialize the machine with the pushbutton located under the table on the right To operate the machine the wor king table and the safety cover should be placed on the machine Insert the feeding plate Item
8. activated O 12345 MM 100_ 2 Press 4 h until the reguired space IV 12345678910 is obtained k see SPEED O O 0058 Adjustment of the pressure of the rollers 1 Press 1 if the light j and the light Ti REVERSE t PRESSURE are not lighted the Y CD O SINE POWER function is activated 2 Press m continuously until display on control panel indicates the required pressure r 12345 ADJUSTMENT OF THE FILMS TENSION The handles Items 8 and 9 are used to adjust the tension of the films on the self locking axles During the lamination the film should be sufficiently tight to ensure a perfect lamination However the film should not be stretched excessively Only by testing can you find the suitable ten sion If some folds appear at level of the rollers increase lightly the tension of the film To increase the tension of the film turn the handles Item 8 or 9 clockwise HOT LAMINATION Feeding of the film Sirocco 1600 Turn on the machine with the switch located at the back of the machine Item 21 The control panel lights Press O t Adjust the temperature of the lamina tion see chapter 3 Remove the safety cover Item 2 and the working table Item 3 Introduce a self locking axle Item 1 inside the mandrel of the film reel Place the assembly on the position A of the machine Centre
9. cutter and recover the feeding plate Adjust the pressure of the rollers accor ding to the application see chapter 3 Lamination on one side and simulta neous application of adhesive Power up the machine with the switch located at rear of the machine Item 21 The control panel lights Press O t Remove the safety cover Item 2 and the working table Item 3 FORWARD O W PRESSURE O OO 12345678910 STOP SPEED O 50085 2 Introduce a self locking axle Item 1 inside the mandrel of the film reel Place the assembly on the position A of the machine base paper of film towards the top Centre the reel with the rules marked on the axle Introduce a self locking axle Item 1 inside the cardboard tube used to recover the film base paper Place the assembly on the position B of the machine Centre the reel with the rules marked on the axle Pass the film and its base paper behind the upper tension bar Item 10 Separate the film from its base paper Stick the base paper on the cardboard tube with the reel pistol Item 23 For the reel of adhesive film without protective paper Introduce a self locking axle Item 1 inside the mandrel of the film reel Place the assembly on the position
10. 22 bet ween the rollers Adjust the rollers on the pressure posi tion 1 see chapter 3 Press 4 h in speed mode and guide the plate through until it comes out on the other side Press the button stop k Cut the film with the safety cutter and recover the feed plate Adjust the pressure of the rollers accor ding to the application see chapter 3 Two sides lamination S 1600 only Turn on the machine with the switch located at rear of the machine Item 21 The control panel lights Press O t Lift the safety cover Item 2 and the working table Item 3 Introduce a self locking axle Item 1 inside the mandrel of the film reel F N FORWARD CO Y PRESSURE O O 12345678910 STOP C SPEED O 0080 Place the assembly on the position A of the machine base paper of film towards the top Centre the reel with the rules marked on the axle Introduce a self locking axle Item 1 inside the cardboard tube to recover the base paper of film Place the assembly on the position B of the machine Centre the reel with the rules marked on the axle Pass the film and its base paper behind the lower tension bar Item 10 Separate the film from its base paper Stick the base paper on the cardboard tube with the reel pistol Item 23
11. 5 70 Maximum speed M minute 3 Dimension Lx H x P in cm 194x137x76 Weight in Kg eem nn sn Rm 287 Minimum and maximum temperature C 40 160 Heating power in watt 3400 Motor power in watt 100 Voltage x eor eee mede x Ane as SA ip asd 230V 240V 50Hz 60Hz AE A Boy rie UE weiss Massie single phase Intensity A xxr eee Eee dee ees 16 Heat up time in minutes 30 9 MAINTENANCE AND SAFETY 9 1 Maintenance FREQUENCY TYPE OF COMPONENTS ACTION Immediately Marks of ink on the rollers or on the table Aqueous solvent Weekly Laminator rollers Aqueous solvent Heating rollers Aqueous solvent Working table Aqueous solvent Rear table Aqueous solvent Safety cover Aqueous solvent Right or left cover guard Aqueous solvent Monthly The support unit Aqueous solvent Upper tension bar Aqueous solvent Lower tension bar Aqueous solvent The cleaning is carried out with the rollers at maximum spacing with power off and safety cover removed the rollers should be at ambiant temperature NEVER LEAVE THE LAMINATOR ROLLERS UNDER PRESSURE DURING A LONG PERIODS STOPPED RISK OF DEFORMATION OF THE SILICONE 9 2 11 Safety Weekly test Emergency stop button Put the rollers under pressure and then set them in motion Press down an emergency stop but ton
12. 60309 1 A CHECK THAT The supply connections must be congruent with the installation rules of the standard NFC 15 100 T INSTALL THE SIROCCO ON A STABLE WORKING BASE CLOSE TO AN EASILY ACCESSIBLE ELECTRIC SOCKET Do not touch the socket with damp hands To unplug the machine disconnect the plug without pulling on the sup ply lead To prevent electric shocks do not use this laminating machine close to water Make a working area behind the machine Do not spill water on the machine the supply lead or the electric soc ket Do not use the machine if the sup ply lead is damaged Do not leave the electric lead in contact with a warm surface The machine should be installed in a well ventilated place The longitudinal knifes should not be used with documents which are not laminated paper rigid sup port Disconnect the general supply of the machine with the switch item 21 after each use During the assembly of the machi ne be careful with the guartz hea ter and the ground areas vibra tions If the machine must be dis assembled call a technician 1 THE RECEPTION OF YOUR SIROCCO 1 1 The choice of the working space Before unpacking your machine it is necessary to determine your working area You should have an easy access to all the parts of the machine 1 2 The unpacking of your machine Take off the upper part of the packing case Remove the axles and the acc
13. U SER S MANUAL Sirocco 1080 Finishing Systems KALA S A S Parc de l Ecotay 35410 Nouvoitou France Fax 433 0 2 99 37 64 65 wwukelafr info kala fr Composants de la plastifieuse Parts list of the laminator Componentes de la plastificadora Rep D signation Axes autobloquants Carter de protection plexiglas Table de travail But e lat rale Paniers support document Capot gauche Capot droit Poign e sup rieure de r glage de la tension des films Poign e inf rieure de r glage de la tension des films Rouleau laminateur sup rieur Rouleau laminateur inf rieur Barre de tension sup rieure Barre de tension inf rieure Rouleau chauffant sup rieur Rouleau chauffant inf rieur Bouton d arr t d urgence Panneau de commande C t s du stand Cloison de stand Roulettes Interrupteur Marche Arr t 10 11 12 13 14 15 16 17 18 19 20 21 Item Designation Self locking axles Plexiglass safety cover Working table Lateral stop Document support trays Left hand cover guard Right hand cover guard Upper Film tension adjust ment handles Lower Film tension adjust ment handles Upper laminator roller Lower laminator roller Upper tension bar Lower tension bar Upper heating roller Lower heating roller Emergency stop button Control panel Sides of support unit Support unit panel Small wheels On Off switch Ref Designaci n 10 11 12 13 14 15 16 17 18
14. aces on the bearing of the lower axle Place the ring on the bearing Turn the ring a guarter towards the top B Rewinder optional A winder axle permits to wind on the laminated support in machine exit This axle is in position Put the plate Item 26 on the right side with the screws supplied Put the plate Item 27 on the left side with the screws supplied Connect the supply to the winder Place the reinforcing bar Item 28 with the screws supplied Introduce a self locking axle Item 1 inside the cardboard mandrel Place the assembly on the position E of the machine Stick the plastified document on the cardboard tube in order to start the reeling Power up the winder with the button Item 24 C Use of the pedal control Advance the key d Press the pedal in order to start the rol lers Your hands are free to guide the document to laminate FORWARD OD PRESSURE O o ADJUSTMENT Cold lamination NB For cold lamination it is possible to heat the rol lers to 50 C to accelerate the polymerization of the adhesive LAMINATION ON ONE SIDE LAMINATION BOTH SIDES Paper Polyester Vinyl Paper Polyester Speed 3 to 5 3 to 5 3 to 5 3 to 5 3 to 5 Pressu
15. and to the replace ment of the power plug in case of replacement use exclusively a CEI 60309 1 model For all others defects contact the installer approved by the manufactu rer DISPOSAL The Sirocco contains no components harmful to the environment The disposal of your Sirocco must be col lected by a recycling company The Sirocco is designed and cons tructed so that the noise emitted during operation is lower than 70 dB
16. ate O m Adjust the pressure of the rollers according to the application see chap ter 3 A Remove pressure from the rollers before switching the machine off A Not to damage the heating rollers during this operation 5 3 Changing of the film rollers Stop the machine by pressing the but ton stop or o k Cut the films of the reels with a safety cutter Item 24 Remove the worned reels and replace them with the new ones Place the new films in such a way that its extremities stick to the old films in contact with the heating rollers Press 4 h Use of the ventilators The ventilators are recommended for cooling the films during the lamination of the documents with thick films The ventilators are started or stopped by pressing the key 9 1080 S1600 Es ais E 6 1 COLD LAMINATION Lamination on one side Turn on the machine with the switch located at the back of the machine Item 21 The control panel lights Press O t Remove the safety cover Item 2 and the working table Item 3 Introduce a self locking axle Item 1 inside the mandrel of the film reel Place the assembly on the position A of the machine The film base paper towards the top Centre the reel with the rules marked on the axle Introduce a self locking axle Item 1
17. e of lamination Visualisation of the active program Stand by position hot lamination Visualisation of the mode cold lamination Starting of the ventilators Forward motion of the rollers rise of the upper roller 81080 81600 Using pedal switch Visualisation of the mode spacing of the rollers Motor stop Selection spacing of the rollers Reverse motion of the rollers descent of the upper roller 51080 S1600 Red light on indicates rollers are heating Control of heating cylinder s Visualisation of the real temperature of the rollers Temperature adjustment Roller pressure and speed digital display 81080 81600 Speed adjustment 81080 1600 Stand by switch Ref Designaci n Visualizaci n de la temperatura Sefial READY Selecci n de las memorias y del modo de plastificaci n Visualizaci n programa activo Modo stand by laminaci n en caliente Visualizaci n del modo de laminaci n en fr o Conexi n de los ventiladores Marcha delantera de los rodillos y des censo del rodillo superior 81080 51600 Control mediante pedal Visualizaci n del modo distancia de los rollos Parada de los motores Selecci n distancia de los rodillos Marcha atr s de los rodillos y descenso del rodillo superior 81080 1600 Piloto rojo enciendido visualiza la pues ta en calentamiento de los rodillos Visualizaci n de la temperatura real de los rodillos Ajuste de la temperatura Visualizaci n digita
18. essories included in the packaging 1 3 The assembly of the support unit Take out the parts which should include 2 sides 1 panel 10 screws One 10 mm flat spanner The assembly is done like this 1 4 The positioning of the laminator on the support unit The machine is heavy A minimum of 4 people is reguired for this ope ration A Do not hold the machine by the late ral cover guards A Hold the machine by its carrying handles Place the machine on the support unit 1 5 Fix the assembly with the screws supplied with the support Start up kit S 1600 only In the packing you will find a comple te start up kit containing Two rollers of thermal film One roller of assembly film double sided One roller of cold adhesive film Two chucks in cardboard PROGRAMMING OF THE SPEED AND THE TEMPERATURE OF THE ROLLERS The programs M1 M2 M3 and M4 can be selected by the operator To activate a program Press or W e buttons continually until the light cor responding to the reguired program comes on When a cold lamination the button f lights on the Sirocco 1080 and 1600 only the speed can be programmed Automatic stand by The light e indicates that the machine has been automatically swit ched to stand by after 30 mn of non use The stand by temperature can be set in the range 40 80 C Programming of
19. ie zuerst noch einmal die Anweisungen durch Wenn das Problem nicht behoben werden kann fra gen Sie Ihren Handler um Rat Stellen Sie sicher dafs die Seriennummer und das Einkaufsdatum Ihres Ger ts griffbereit sind falls Sie die Maschine zum H ndler zur cksenden m ssen Die Transportsch den die von einer fehlerhaften Verpackung herr hren stellen keinen Garantiefall dar Disposizioni per la restituzione Se la vostra Sirocco non funziona correttamente si consiglia innanzitutto di rileggere il libretto d istruzioni Qualora non fosse possibile correggere il funziona mento difettoso chiedete consiglio al vostro fornitore Accertatevi di avere sotto mano il numero di serie della macchina e la data di acquisto nel caso in cui dobbia te restituire la macchina al fornitore danni da traspor to dovuti ad un imballaggio difettoso non sono coperti ai sensi delle condizioni della presente garanzia Reglamentaci n de devoluci n Si su m quina Sirocco no funciona bien lea de nuevo las instrucciones Si el funcionamiento defectuoso no puede corregirse con stas solicite consejo a su pro veedor Cerci rese de que el n mero de serie y la fecha de compra del aparato est n al alcance de la mano si debe devolver la m quina al proveedor Los da os de transporte que resulten de un embalaje defectuoso no est n cubiertos por esta garant a AO A 10 11 12 13 SUMMARY THE RECEPTION OF YOUR SIROCCO 1 1 The choice of yo
20. l de la presi n o de la velocidad de los rodillos S1080 1600 Ajuste de la velocidad 81080 1600 Puesta en vela Ber hrungsfeld Steuerpult Pannello di controllo TO 0200 0700 5 3 x n Pos Bezeichnung digitale Temperaturanzeige Anzeige Betriebsbereit Auswahl Speicher und Betriebsart Anzeige aktives Programm Stand by Heiftlaminieren Betriebsanzeige Kaltlaminieren K hlventilatoren einschalten Walzen vorw rts laufen lassen und obere Walze hochfahren S1080 S1600 FuRschalter Betriebsanzeige Walzen ffnen Motor abschalten Auswahl Walzen ffnung Walzen r ckw rts laufen lassen und obere Walze senken 51080 51600 Einstellungsanzeige Heizzylinder ein geschaltet die rote Diode leuchtet Auswahl der Heizzylinder Anzeige der echten Walzentemperatur Temperatureinstellung digitale Druckanzeige oder Walzenge schwindigkeitsanzeige S1080 1600 Geschwindigkeitseinstellung S1080 51600 Hauptschalter Rif Descrizione Display digitale della temperatura Spia ready Selezione delle memorie e della modalit di plastificazione Visualizzazione del programma attivo Modalit standby plastificazione a caldo Visualizzazione della modalit plastifica zione a freddo Avviamento dei ventilatori Marcia in avanti dei rulli salita del rullo superiore S1080 81600 Comando tramite pedale Visualizzazione della modalit dis tanza dei rulli Arresto dei mot
21. n 1997 Always seeking to make progress we reserve ourselves the right to change without notice the models as well as the eguipment and their technical features Konformit tsbest tigung KALA SAS Spannung 220 240V Parc de l Ecotay Maschinenrichtlinie 98 37 CEE 35 410 NOUVOITOU Niederspannungs Richtlinie 73 23 CEE FRANCE gem ss EN 60204 1 1997 best tigt da folgendes Produkt Richtlinie bez glich der elektromagnetischen Modell SIROCCO folgende Forderungen erf llt Vertr glichkeit 89 336 CEE gem ss EN 55014 Ausgabe 1993 und EN 55014 2 Ausgabe 1997 Sempre alla ricerca di innovazioni ci riserviamo il diritto di modificare senza preavviso i modelli le apparecchiature e le loro caratteristiche tecniche Dichiarazione di conformit KALA S A S Tensione 220 240V Parc de l Ecotay Direttiva macchina 98 37 CEE 35 410 NOUVOITOU Direttiva bassa tensione 73 23 CEE confor FRANCE memente alla normativa EN 60204 1 1997 Dichiara che il seguente prodotto pu Direttiva Compatibilit Elettromagnetica 89 336 Modello SIROCCO conforme alle seguenti diret CEE conformemente alla normativa EN 55014 tive Edizione 1993 e EN 55014 2 Edizione 1997 Sempre alla ricerca di innovazioni ci riserviamo il diritto di modificare senza preavviso i modelli le apparecchiature e le loro caratteristiche tecniche Declaraci n de conformidad KALA S A S Voltaje 220 240V Parc de l Ecotay
22. ori Selezione distanza dei rulli Marcia indietro dei rulli discesa del rullo superiore 81080 1600 Spia rossa accesa visualizza il riscal damento dei rulli Selezione dei rulli riscaldanti Visualizzazione della temperatura reale dei rulli Regolazione della temperatura Display digitale della pressione o della velocit dei rulli 81080 81600 Regolazione della velocit S1080 S1600 Messa in standby D claration de conformit KALA S A S Voltage 220 240V Parc de l Ecotay Directive machines 98 37 CEE incluant 35 410 NOUVOITOU Directive basse tension 73 23 CEE selon la FRANCE norme EN 60204 1 1997 D clare que le produit suivant Directive Compatibilit Electromagn tique Mod le SIROCCO est conforme aux exigences 89 336 CEE selon la norme EN 55014 suivantes Edition 1993 et EN 55014 2 Edition 1997 Toujours la recherche du progr s nous nous r servons le droit de modifier sans pr avis les modeles ainsi que les quipements et leurs caract ristiques techniques Declaration of conformity KALA S A S Voltage 220 240V Parc de l Ecotay Machine Directive 98 37 EEC 35 410 NOUVOITOU Low voltage Directive 73 23 EEC according FRANCE to the EN 60204 1 1997 Declares that the following product Electromagnetic compatibility Directive 89 336 SIROCCO Model conforms to the following require EEC according to the EN 55014 Edition 1993 ments and EN 55014 2 Editio
23. re 4 to 5 4 to 5 2to3 4 to 5 4 to 5 Paper Polyester Foam Speed 3to6 3 t0 6 4 to 7 4 to 7 Pressure 4to5 4to 5 1to2 2to3 Lamination Hot encapsulation values given for information only OFFSET DOCUMENT INKJET DOCUMENT Films um T C Speed Pressure T C Speed Pressure 42 110 120 1 3 3 5 90 100 1 3 3 5 75 110 120 1 3 3 5 90 100 1 3 2 5 125 115 125 1 3 3 5 90 100 1 3 2 5 250 120 130 1 2 3 5 90 100 1 2 2 5 8 1 8 2 TECHNICAL CHARACTERISTICS SIROCCO 1080 Maximum working width in MM 1080 Maximum space between rollers in mm 25 Roller pressure in daN 15 70 Maximum speed M minute 3 Dimension L x H x P in cm 142x58x62 Dimension L x H x P in cm with stand 142x126x76 Weight stand weight in Kg 122 42 Minimum and maximum temperature C 40 160 Heating power in watt 2800 Motor power in watt 100 Voltage tsa s xo gn pes ER 28 bees be ee eS 230V 240V 50Hz 60Hz TE single phase Intensity A eee RR RR Ren 13 Heat up time in minutes 15 SIROCCO 1600 Maximum working width in mm 1600 Maximum space between rollers in mm 25 Roller pressure in daN 1
24. ricaci n durante un periodo de un afio despu s de la fecha de compra En caso de defectos de material o fabricaci n la sociedad que ha vendido el aparato lo reparar en sus talleres o lo devolver al fabricante no habiendo ninguna otra garant a Estas garant a no cubre los dafios particula res o que resulten de causas indirectas previsibles o imprevisibles La garant a no cubre la mala utilizaci n de la m quina R glementation de retour Si votre Sirocco ne fonctionne pas bien relisez d a bord les instructions Si le fonctionnement d fectueux ne peut tre corrig demandez conseil votre four nisseur Assurez vous que le num ro de s rie et la date d achat de votre appareil soient port e de main Si vous devez retourner la machine au fournisseur elle devra tre dans son emballage d origine Les dommages de transport r sultants d un emballage d fectueux ne sont pas couverts selon les termes de cette garantie Return regulations If your Sirocco does not fwork correctly firstly read the instructions again If the defective operation cannot be corrected consult your supplier Make sure that the series number and the date of purchase of your machine are to hand if you have to return the machi ne to the supplier Damage during transport resulting from defective packaging is not covered under the terms of this guarantee R cksendungs Regelung Falls Ihre Sirocco nicht richtig funktionieren sollte lesen S
25. riore di regola zione della tensione dei film Rullo laminatore superiore Rullo laminatore inferiore Barra di tensione superiore Barra di tensione inferiore Rullo riscaldante superiore Rullo riscaldante inferiore Pulsante di arresto d emergenza Pannello di controllo Lati del supporto Divisorio del supporto Rotelle Interruttore acceso spento SIROCCO 1080 1600 Panneau de commande Control panel Cuadros de mandos 0 T9 TO 100 Rep D signation Affichage digital de la temp rature Voyant Ready S lection des m moires et du mode de plastification Visualisation du programme actif Mode veille plastification chaud Visualisation du mode plastification froid Mise en route des ventilateurs Marche avant des rouleaux mont e du rouleau sup rieur 81080 S1600 Commande par p dale Visualisation du mode cartement des rouleaux Arr t des moteurs S lection cartement des rouleaux Marche arri re des rouleaux descente du rouleau sup rieur 81080 S1600 Voyant rouge allum visualise la mise en chauffe des rouleaux S lection des rouleaux chauffants Visualisation de la temp rature r elle des rouleaux R glage de la temp rature Affichage digital de la pression ou de la vitesse des rouleaux 81080 S1600 R glage de la vitesse 81080 51600 Mise en veille 0 T9 TO 00 Item Designation Digital temperature display Ready light Selection of the memories and of the mod
26. s warranty does not cover indivi dual damage or damage resulting from indirect caus es whether foreseeable or not The warranty does not cover incorrect use of the machine Garantie Ihre Sirocco Maschine weist vom Kaufdatum ab eine ein j hrige Garantie gegen jeglichen Material und Herstellungsfehler auf Falls Material oder Herstellungsfehler auftreten sollten so wird die Firma die das Ger t verkauft hat dieses in ihren eigenen Werkst tten reparieren oder an den Hersteller zur cksen den Es gibt keinerlei andere Garantie als die obenge nannte Diese Garantie deckt nicht die besonderen Sch den oder die Sch den die indirekt verursacht worden sind ob diese vorhersehbar sind oder nicht Die Garantie deckt nicht die falschen Anwendungen der Maschine Garanzia La garanzia della vostra Sirocco copre tutti i difetti di materiale e di fabbricazione per un anno a partire dalla data di acquisto In caso di difetti di materiale o di fab bricazione la societ che ha venduto la macchina provveder a ripararla presso il proprio servizio assis tenza o a restituirla al fabbricante Non esiste altra garanzia oltre a quella sopra citata Tale garanzia non copre i danni speciali o dovuti a cause indirette indi pendentemente dal fatto che siano o meno prevedibi li La garanzia non copre i danni legati ad un cattivo uso della macchina Garant a La m quina Sirocco est garantizada contra todos los defectos de material y fab
27. safety cutter and recover the feeding plate Adjust the pressure of the rollers accor ding to the application see chapter 3 1060665 7 FORWARD CO Y PRESSURE O O 12345678910 STOP O SPEED O Mounting and sticking on an adhesive support On the adhesive document peel back a strip of protective paper from the film about 2 cm and fold back Place the document and stick it on the support Protective paper a Document Support paper Support Set the rollers at maximum separation see chapter 3 Place a mandrel with a cardboard tube on the position B Shows the assembly for adhesive application on the working table bet ween the rollers Place the document to be mounted on the cardboard tube in position B Adjust the rollers on the pressure posi tion 1 see chapter 3 For the Sirocco 1080 1600 Press 4 c in speed mode and guide the plate through until it comes out on the other side Peel back the protective paper pro gressively as it advances towards the laminator rollers by guiding manually N Support A PRESSURE O eee ME stop O SPEED O E Fe 10068 6 5 Simplification of utilization A Blocking ring It allows to avoid the shrinking of the lower self locking axle during a lamination on one side or and a simultaneous adhesive application It pl
28. the reel with the rules marked on the axle Introduce a self locking axle Item 1 inside the mandrel of the film reel Place the assembly on the position C of the machine Centre the reel with the rules marked on the axle Place the film of the upper roller on the heating rollers adhesive side facing towards you by passing besides of the lower tension bar Place the film of the lower roller on the upper film adhesive side facing towards you by passing besides of the lower tension bar Respect the direction of the film accor ding to its size Diagram 8 The adhesive is outsi de the rollers Diagram 9 The adhesive is inside the rollers The temperature of the rollers must be sufficiently important to stick the films Place the safety cover Item 2 and the working table Item 3 To operate the machine the wor king table and the safety cover must be in place on the machine Insert the feeding plate Item 22 bet ween the rollers Adjust the rollers on the pressure posi tion 1 see chapter 3 Press 4 h speed mode and guide Y TP FORWARD _ PRESSURE O the feeding plate through until it comes spes out on the other side a pom ni Press stop o k yt SPEED Cut the film with a safety cutter and E recover the feeding pl
29. the speed Sirocco 1080 1600 To set up the speed the light j must be off If not press 1 Adjust the speed of the rollers by pres sing the and E keys s of the control panel The last value entered automatically replaces the previous stored value A For security reasons the transition from cold to hot mode desactivates the heating rollers Before hot lamina tion it is necessary to start them up again by pressing 0 F 3 h FORWARD CD PRESSURE O i 9 o j 12345678910 k STOP O SPEED O cesa 2 3 Programming of the temperature Sirocco 1080 1600 Adjust the temperature of the rollers by pressing the keys m i q of the control panel Start the roller heating by pressing 0 and it is indicated by the light e n To know the temperature of a roller press the button p If the light b is on the required tem perature is obtained ready A The last value entered replaces automatically the previous stored value 3 ADJUSTMENT OF THE ROLLERS PRESSURE The Sirocco is fitted with a device for adjusting the space and the roller pressure This device permits to laminate thick supports Maximal thickness 25 mm Sirocco 1080 1600 Adjustment of the space between the rollers 1 Press 1 if the light j and the light N PRESSURE are not lighted the h llrorwaro CO PRESSURE O function is
30. ur working space 1 2 The unpacking of your machine 1 3 The assembly of the support unit 1 4 The positioning of the laminator on the support unit 1 5 The start up kit of films PROGRAMMING OF THE SPEED AND OF THE TEMPERA TURE OF THE ROLLERS 2 1 Automatic stand by 2 2 Programming of the speed 2 3 Programming of the temperature ADJUSTMENT OF THE ROLLERS PRESSURE ADJUSTMENT OF THE FILMS TENSION HOT LAMINATION 5 Feeding of the film Sirocco 1600 5 2 Change of rollers 5 3 Ventilator use COLD LAMINATION 6 1 Lamination on one side only S 1600 6 2 Lamination on one side and simultaneous adhesive application S 1600 6 3 Recto Verso lamination S 1600 6 4 Mounting and sticking on an adhesive support 6 5 Simplification of use ADJUSTMENTS TECHNICAL CHARACTERISTICS 8 1 SIROCCO 1080 8 2 SIROCCO 1600 MAINTENANCE AND SAFETY 9 1 Maintenance 9 2 Safety weekly test FILM REELS CONDITIONING INCIDENTS MAINTENANCE DISPOSAL PAGE PAGE PAGE PAGE PAGE PAGE PB PB O OQ PAGE PAGE PAGE PAGE PAGE PAGE o oco oar A PAGE Pace 6 Pace 10 Pace 10 Pace 11 Pace 11 Pace 15 PAcE 22 Pace 28 Pace 30 Pace 33 Pace 34 Pace 34 Pace 34 Pace 35 Pace 35 Pace 36 Pace 36 Pace 36 Pace 38 Pace 38 The tension of your machine cor responds with the tension of your electrical network The machine s supply needs to be placed at disposal of a stand base of a compatible electric socket CEI
Download Pdf Manuals
Related Search