User Manual
Contents
1. ON OFF OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF OFF OFF ON ON OFF OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF OFF ON OFF ON OFF OFF OFF OFF OFF OFF ON ON OFF OFF OFF OFF OFF ON ON ON OFFJOFF OFFJOFFJOFF OFF OFF OFF ON OFF OFF OFF OFF Factory default Switch positions Speed dome ID is set using standard binary notation O S D AA OIN ON ON ON ON ON ON ON ON 255 1 Carefully unclip the black inner dome 2 Locate the dip switches and set protocol and ID according to the table opposite Note ID 0 should not be used Where multiple speed domes are connected a unique ID must be assigned to each one 3 Reassemble the speed dome Refit the black inner dome cover and outer dome cover If the lanyard safety wire was removed it must be refitted before the dome cover is fixed 4 Fix the bracket 5 Wire up the junction box 1 Fix the supplied mounting template taking account of any pipework cables overhangs etc that may obstruct the bracket once fitted 2 After making suitable checks for buried pipes and cables drill fixing holes suitable for the bolts supplied with the speed dome Pendent option Pendent option 3 Remove the junction box cover Using the2. VHSD 770EXT High Speed Dome System User Manual Contents Before installing Hmmm 1 Key features Reemi 5 Configure fix and Wire emen eene eee 3 Basic speed dome operation emm 6 Programming the speed dome ms 7 Using the speed dome features Re 13 Parts and dimensions sesenta 14 Wiring SCHEMA ALI etre rrt sed 15 Specifications eee esiisa de asii cie 16 installer notes eoe eee Ire So hoe eaa teen tet ee Rt e ES AES 17 Before installing A Installation should be carried out only by qualified personnel and in accordance with any wiring regulations in force at the time The speed dome is heavy and could cause injury if not correctly mounted in accordance with these instructions Use only the fittings supplied with the speed dome and ensure that all lanyard safety cables are connected correctly during installation Adequate protection against lightning strikes and power surges must be installed to prevent damage to the speed dome Any safety warnings on the product and in these instructions must be adhered to If cleaning is necessary disconnect power to the speed dome first Do not use abrasive cleaners as these will cause damage to the cover and cause poor image quality Use a damp cloth to gently clean the dome cover and dry off with a soft clean cloth Do not use any brackets mounts or other accessories not specifically designed for use with this speed dome Do not attempt to ser
3. VSTfunction Up to 8 speed adjustable Groups Up to 8 each with up to 20 actions preset pattern tour or VST Privacy zones Up to 4 user definable Park function Park to specified preset pattern or VST after a defined period of inactivity 1 min 4 hours Communication Data type RS 485 Protocols Pelco D or Pelco P Baud rates 2400 4800 9600 Camera ID 1 255 Alarm I O 8 inputs 4 outputs On Screen Display OSD menu camera position dome ID alarm status preset VST pattern tour status Mechanical Fan Heater Built in Sunshield Fitted Operating temperature range 35 deg C to 50 deg C Humidity lt 95 Power supply 24V AC 20 watts maximum heater on Dimensions with standard wall Bracket and sun shield fitted Overall height 530mm Overall width 230mm Overall depth 342mm 16 Installer notes Make a note of any specific installation details here which would be useful for future reference 17
4. item to modify and key NEAR Use the joystick to change the setting and key NEAR to save or FAR to cancel Edit group EDIT GROUP 1 NEAR EDIT From the group setup menu use the joystick to highlight EDIT GROUP and key NEAR To edit the group key NEAR again Header explanation NO the item number between 1 amp 20 ACTION the specific action for this item the action number eg if ACTION is set to PRESET this value can be between 1 amp 128 DWELL the amount of time before the next action in the list is called OPT for PRESET actions this value is the speed at which the dome moves to the preset For VST and PATTERN this value is the number of times the action is repeated before the next action is called Move the joystick up and down to choose the group item to modify and key NEAR The ACTION is highlighted in white Move the joystick up and down to change the action type between NONE PRESET VST and PATTERN Move the joystick left and right to select and edit values for DWELL amp OPT 12 Edit group EDIT GROUP 1 1 PATTERN 2 PRESET 3 VST 4 PRESET 5 PRESET NEAR EDIT Key NEAR to save this item and continue adding more items as necessary or key FAR to exit Password setup PASSWORD SETUP gt CHECK PASSWORD XEDIT PASSWORD From the main menu use the joystick to highlight PASSWORD SETUP and key NEAR CHECK PASSWORD ON OFF when set to ON the c
5. position Confirmation and preset title if defined is displayed on the OSD To reprogramme a preset position follow the steps for programming a preset it is not necessary to delete the old preset position first CAMERA ID Shows the current ID as defined by the dip switch settings PTZ INFORMATION The current pan tilt position in degrees and the current zoom level Programming the speed dome The speed dome setup menu allows the operator to customise and program all aspects of speed dome operation All menu settings are retained in non volatile memory so if power is lost to the speed dome for any reason all settings will be retained High SPEED DOME gt lt SYSTEM INFORMATION lt DISPLAY SETUP gt lt DOME CAMERA SETUP gt lt PASSWORD SETUP gt lt SYSTEM INITIALISE gt To access the speed dome setup menu key PRESET 95 ENTER To navigate the main menu move the joystick up down to choose a menu item or change settings within a menu item To enter a menu item or confirm a new setting key NEAR To exit a menu item or cancel a new setting key FAR Where a menu item is surrounded by brackets it indicates that there is a sub menu Where a menu screen shows EXIT selecting this option will exit the menu and the speed dome will return to normal operation Where a menu screen shows BACK selecting this option will return to the higher menu level The main menu has five
6. power is restored after a power failure AUTO FLIP ON OFF when set to ON the dome will flip 180 degrees when the tilt position reaches 90 degrees JOG MAX SPEED determines the maximum speed in degrees second the dome will move during manual operation JOG DIRECTION INVERSE NORMAL when set to normal the pan direction is opposite to the joystick movement PARKING ACTION SETUP Configure actions that run automatically after a defined period of inactivity FRZ IN PRESET FREEZE IN PRESET When a new preset is selected the speed dome will freeze the last picture until the new preset is reached ALARM ACTION SETUP Configure the action of the alarm inputs Highlight the item to modify and key NEAR Use the joystick to change the setting and key NEAR to save or FAR to cancel Parking action setup PARKING ACTION SETUP SPARK ENABLE WAIT TIME 00 10 00 PARK ACTION HOME From the motion setup menu use the joystick to highlight PARKING ACTION SETUP and key NEAR PARK ENABLE when set to ON the speed dome will run the specified park action after the wait time has elapsed WAIT TIME can be set between one minute and 4 hours If no manual control occurs during this time the park action will run PARK ACTION choose the action to run after the wait time has elapsed This can be return to home position go to a preset or run a VST GROUP or PATTERN TOUR Highlight the item to modify an
7. supplied bolts and tool firmly fix the bracket 4 Feed the speed dome cable through the bracket To Power PCB board _RS 485 24V AC Power Video Out put Ill 3 U 934 B Speed dome cable ane RS 485 Ter mination Resistor muse Ad A3 AZ AT gl HE i KKK AK iua Alarm output 1 4 Alarm Input 1 8 Alarm output 4 Alarm Input 1 4 7 Alarm output 2 Alarm output 3 Pendent option 5 Bring the speed dome up to the bracket 6 Tighten the three screws to fix the speed dome and ensure the lanyard safety chain is properly connected Video output standard 1V P P Use good quality 75 Ohm cable terminated with a BNC connector RS 485 termination resistor switch to ON if the speed dome is the last device on the telemetry line 24V AC Power use only the PSU supplied with the speed dome ora PSU approved for use with the speed dome RS 485 telemetry connection Use unshielded CAT5 or Beldon 8723 Connect A to A or D of your control equipment and B to B or D The terminals are duplicated for daisy chaining purposes Alarm outputs switched voltage free outputs Outputs 3 and 4 can be set either NO or NC by changing the jumpers Alarm inputs standard NO inputs with common ground Speed dome cable mult
8. OFF set which relays are triggered when the preset is called Highlight the item to modify and key NEAR Use the joystick to change the setting and key NEAR to save or FAR to cancel VST setup VST SETUP 1ST POS 2ND POS NOT USED NOT USED VST SPEED CLEAR VST RUN VST 30 SEC CANCEL BACK EXIT From the dome camera setup menu use the joystick to highlight VST SETUP and key NEAR VST NO 1 8 shows the VST number currently being modified 1ST POS any defined preset between 1 amp 128 2ND POS any defined preset between 1 amp 128 VST SPEED determines the speed of movement in degrees per second between each preset position CLEAR VST deletes the currently selected VST function RUN VST runs the currently selected VST function for testing purposes Highlight the item to modify and key NEAR Use the joystick to change the setting and key NEAR to save or FAR to cancel Note A VST always moves anti clockwise to the 1st position and then clockwise to the 2nd position Pattern setup PATTERN SETUP 2PATTERN NO CLR PATTERN RUN PATTERN EDIT PATTERN CANCEL From the dome camera setup menu use the joystick to highlight PATTERN SETUP and key NEAR PATTERN NO 1 4 The pattern number currently being modified CLR PATTERN the currently selected pattern can be deleted RUN PATTERN runs the currently selected pattern for testing purposes EDIT PA
9. SU is approximately 24V AC If the power LED is lit check the BNC crimp connection is correctly made at both the PCB end and the DVR monitor matrix end A portable test monitor connected directly to the video output of the speed dome is also a useful test if a picture is displayed double check the BNC connections and the signal cable used No PTZ control check that the control equipment you are using is compatible with the speed dome and is configured to match the speed dome settings correctly If dip switches were changed on the speed dome check the power on self test screen to ensure that protocol ID and baud rate are as expected If the settings match you should check the polarity of the connections both on the control equipment and the speed dome If you suspect there is a polarity issue swap the A amp B wires at the speed dome to see if this resolves the problem Check also that there are no other telemetry devices on the system with the same ID as the speed dome If in doubt connect the speed dome directly to the PTZ controller and isolate all other equipment Basic speed dome operation There are many different PTZ keyboards and DVR systems capable of controlling this speed dome and it would be impossible to describe them all here Therefore examples given in the following pages are based on the more popular control equipment available Whilst the principles of operation are the same regardless of the con
10. TTERN allows the operator to program a patten tour Highlight the item to modify and key NEAR Use the joystick to change the setting and key NEAR to save or FAR to cancel 11 Edit pattern EDIT PATTERN 4 MOVE TO START POSITION NEAR START FAR CANCEL From the pattern setup menu use the joystick to highlight EDIT PATTERN and key NEAR Position the speed dome to the desired starting point and key NEAR EDIT PATTERN 4 NEAR SAVE FAR DELETE Move the dome to the various positions and zoom levels required for the pattern The white squares at the top of the display show remaining storage and disappear as the pattern is recorded To save the pattern key NEAR To abandon pattern programming key FAR Note Pattern tour memory is only used when movements are recorded Pauses between movements regardless of time do not use pattern tour memory Group setup GROUP SETUP gt GROUP NO CLEAR GROUP RUN GROUP lt EDIT GROUP gt CANCEL From the dome camera setup menu use the joystick to highlight GROUP SETUP and key NEAR GROUP NO 1 8 shows the group number currently being modified CLEAR GROUP the currently selected group can be deleted RUN GROUP runs the currently selected group for testing purposes lt EDIT GROUP allows the operator to program the group functions Highlight the
11. be a mix of preset positions pattern tours and VST functions Up to 8 groups can be defined and each group can have up to 20 actions which repeat indefinitely until interrupted by the operator or an alarm input Specific parameters such as preset speed dwell time and action loop can also be specified Privacy zones By defining a privacy zone sensitive scenes such as windows can be masked off so they cannot be viewed by the operator Up to 4 privacy zones can be defined Privacy zone size adjusts automatically depending on the speed dome zoom level Alarm inputs and outputs This speed dome has 8 alarm inputs and 4 alarm outputs Any alarm input can be set to call a predefined preset VST function pattern or group Any preset can be configured to activate any or all of the alarm outputs For example a PIR detector connected to alarm input 1 could call preset 7 to view that particular scene whilst activating an external lamp connected to relay 1 and an external siren connected to relay 3 On Screen Display OSD The operator can choose if any or all of the following information is displayed on screen during normal speed dome operation Preset status and title Speed dome position coordinates and zoom level Alarm I O status Time and Date Speed dome ID The speed dome also has a full on screen menu setup allowing quick and easy configuration of all the speed dome features Powerful park function The speed dome can be configure
12. blue colour content can be adjusted Highlight the item to modify and key NEAR Use the joystick to change the setting and key NEAR to save or FAR to cancel Auto exposure setup AE SETUP 3BACKLIGHT DAY NIGHT BRIGHTNESS IRIS SHUTTER AGC SSNR SENS UP From the zoom camera setup menu use the joystick to highlight AUTO EXPOSURE SETUP and key NEAR BACKLIGHT ON OFF DAY NIGHT AUTO DAY NIGHT the operator can choose to fix the camera in to DAY colour or NIGHT B amp W with IR cut filter mode In AUTO mode the camera switches between DAY and NIGHT depending on the surrounding light level BRIGHTNESS 0 100 IRIS Auto Manual SHUTTER ESC Manual Flickerless In ESC mode the speed dome determines the optimum exposure setting AGC Off Low Middle High SSNR Off Low Middle High SENS UP Auto Off Highlight the item to modify and key NEAR Use the joystick to change the setting and key NEAR to save or FAR to cancel Motion setup MOTION SETUP 3PRESET LOCK PWR UP ACTION AUTO FLIP JOG MAX SPEED JOG DIRECTION FRZ IN PRESET PARKING ACTION SETUP ALARM ACTION SETUP 160 SEC INVERSE BACK EXIT From the dome camera setup menu use the joystick to highlight MOTION SETUP and key NEAR PRESET LOCK when set to ON preset programming directly from the keyboard is disabled to prevent tampering PWR UP ACTION when set to ON the speed dome will resume its last operation when
13. d key NEAR Use the joystick to change the setting and key NEAR to save or FAR to cancel Alarm action setup ALARM ACTION SETUP gt ALARM ALARM ALARM ALARM ALARM ALARM ALARM ALARM BACK EXIT From the motion setup menu use the joystick to highlight ALARM ACTION SETUP and key NEAR ALARM 1 8 ACT for each alarm action specifies the preset number VST pattern tour or group to call Leave set to NOT USED to disable the alarm input Highlight the item to modify and key NEAR Use the joystick to change the setting and key NEAR to save or FAR to cancel Preset setup PRESET SETUP gt PRESET NO CLR PRESET lt EDIT SCENE gt lt EDIT LABEL gt lt RELAY OUT gt ee CANCEL From the dome camera setup menu use the joystick to highlight PRESET SETUP and key NEAR PRESET NUMBER 1 128 The preset number currently being modified If the preset number is already defined the speed dome will move to that preset position otherwise UNDEFINED is displayed under the preset number CLR PRESET use this option to delete the current preset position EDIT SCENE gt use this option to program the preset position EDIT LABEL gt use to edit the preset label This option is only available when the selected preset position is already programmed RELAY OUT use to program the relay outputs required if any when the preset is called This option is only available when the selected pr
14. d to run a specified VST function pattern tour group or preset after a defined period of inactivity Configure fix and wire Before proceeding with installation the speed dome foam packing pieces must be removed Remove the outer dome cover with the tool supplied and carefully remove the foam packing pieces When handling the dome cover always wear the gloves supplied to avoid getting fingerprints on the outer dome cover 1 Remove the foam packing pieces 1 Wearing the gloves and using the supplied 2 Remove the foam pieces from the camera ool remove the outer dome cover module 2 Change protocol baud rate and ID if required The factory default setting is Pelco D 2400 ID 1 Skip to section 3 if these settings match your control equipment Protocol amp Baud rate DIP switch table 1 2 Protocol Rate on OFF OFF Pelco D 2400 bps ON OFF Pelco D 9600 bps ee OFF ON Pelco P 4800 bps Factory default ON ON Pelco P 9600 bps switch positions Note Dip switches 3 6 are reserved and must not be changed Speed dome ID DIP switch table ON 1 2 3 4 5 6 7 8 DIP 1 2 4 8116 32 64128 2 Tp
15. eset position is already programmed Highlight the item to modify and key NEAR Use the joystick to change the setting and key NEAR to save or FAR to cancel 10 Edit scene EDIT SCENE PRESET 1 MOVE TO TARGET POSITION NEAR SAVE FAR CANCEL From the preset setup menu use the joystick to highlight EDIT SCENE and key NEAR Using the joystick move the speed dome to the desired position and zoom level and key NEAR to save or FAR to cancel Edit label EDIT LABEL PRESET 1 1234567890 ABCDEFGHIJ KLMNOPQRST UVWXYZabcd efghijklmn opqrstuvwx yz lt gt Backspace Space From the preset setup menu use the joystick to highlight EDIT LABEL and key NEAR The solid white square shows the current cursor position The flashing white square shows the currently selected character Move the joystick up down left right to choose the required character and key NEAR to insert it in the preset label The solid white square moves to the next cursor position Repeat until the preset label is complete If a mistake is made use the joystick to select the backspace and key NEAR The cursor moves back one square Select OK to save the preset label or CANCEL to lose changes and key NEAR to exit Relay out RELAY OUT PRESET 1 3RELAY OUT RELAY OUT RELAY OUT RELAY OUT From the preset setup menu use the joystick to highlight RELAY OUT and key NEAR RELAY OUT 1 4 ON
16. factory reset on the speed dome All presets VST functions patterns groups and privacy zones will be erased CLR DISPLAY SET this option will reset the on screen display settings to factory default and erase all privacy zones CLR CAMERA SET this option will reset the camera module settings to factory default CLR MOTION SET this option will reset the motion menu settings to factory default CLR EDIT DATA this option will erase all presets VST functions patterns and groups Highlight the item to modify and key NEAR Use the joystick to change the setting to ON and key NEAR to run or FAR to cancel Using the speed dome features Once the pattern tours VST functions and groups have been programmed in the speed dome setup menu they can all be accessed directly from the PTZ control equipment by using the following sequences 1 To start a pattern tour press PRESET 13X ENTER Where X is a pattern tour number between 1 amp 4 The selected pattern tour will run indefinitely until a manual movement is made by the operator or an alarm input is received 2 To start a VST function press PRESET 14X ENTER Where X is a VST function number between 1 amp 8 The selected VST function will run indefinitely until a manual movement is made by the operator or an alarm input is received 3 To start a group press PRESET 15X ENTER Where X is a group number between 1 amp 8 The selected group will run inde
17. finitely until a manual movement is made by the operator or an alarm input is received 13 Parts and dimensions Bracket Mount Base 4 Bracket Upper Cover Sunshield Dome Housing Pan Motor 248 Bracket Joint Housing Upper Cover Thermostat Heater Thermostat Shield Mount Tilt Motor Inner dome cover Dome Cover Zoom Module Wiring schematic E Power Cable as a A o 24V AC PSU o Video Cable RS 485 Cable d Alarm Input Cable i Alarm Output Alarm Sensor Cable Siren Light etc DO power source Siren Light etc 15 Specifications Camera CCD 74 Samsung Techwin Day Night Resolution 540TVL Minimum Illumination 0 1 Lux Optical Zoom 23x f 3 84 88 4mm F 1 6 3 2 Digital Zoom 2X 4X amp 8X S N Ratio 50db Focus Auto Manual White Balance ATW Manual Back Light compensation Low Middle High Off Pan Tilt General Pan 360 degrees continuous rotation Tilt 90 degrees with auto flip function Speeds Manual pattern tour 1 255 degrees second Preset to preset 360 degrees second VST 1 255 degrees second adjustable in 1 degree steps Preset positions Up to 128 10 character title per preset Pattern tours Up to 4
18. group functions Highlight the setup menu required and key NEAR Remember A menu item surrounded by brackets shows it has a sub menu Camera setup ZOOM CAMERA SETUP FOCUS MODE SEMIAUTO DIGITAL ZOOM ON IMAGE FLIP OFF WHITE BALANCE SETUP lt AUTO EXPOSURE SETUP From the dome camera setup menu use the joystick to highlight CAMERA SETUP and key NEAR FOCUS MODE MANUAL the operator must focus the camera manually using the NEAR and FAR keys SEMIAUTO the camera automatically focuses during normal PTZ movement but preset focus information is stored when a preset is programmed and recalled each time the preset is called AUTO the module auto focuses continually DIGITAL ZOOM ON OFF disables or enables the 8x digital zoom When disabled the maximum zoom level is 23x optical IMAGE FLIP ON OFF WHITE BALANCE SETUP sub menu to change the white balance settings AUTO EXPOSURE SETUP sub menu to change the auto exposure settings White balance setup WB SETUP WB MODE RED ADJUST BLUE ADJUST From the zoom camera setup menu use the joystick to highlight WHITE BALANCE SETUP and key NEAR WB MODE AUTO MANUAL AUTO the speed dome determines the optimum white balance settings for a given Scene MANUAL the operator can adjust white balance settings manually RED ADJUST in manual mode the red colour content can be adjusted BLUE ADJUST in manual mode the
19. i way connection plug to the speed dome 6 Complete the install 1a wall bracket option After making all the connections to the PCB fit the junction box cover with the four screws 1b pendent option After making all the connections to the PCB raise the dome assembly to the junction box connect the dome cable to the PCB and fix with the four screws Note when fixing the cover to the junction box ensure that the seal is also fitted properly and that none of the cables are trapped 7 Verify basic operation HIGH SPEED DOME FIRMWARE VER 1 0S18V COLOUR SYSTEM PAL PROTOCOL PELCO D ADDRESS 1 BAUD RATE 2400 DATA MEMORY OK ZOOM MODULE OK ALARM I O OK 0 Or HOME TEACHING END 1 12345678 WAIT 325 37 x1 1 After carefully checking the installation including all cable connections apply power to the dome and check that the startup and self test screen is displayed 2 After the self test is complete the dome starts normal operation Verify that there is basic PTZ control from your control equipment If there s a problem atthis stage Work through the logical steps below to determine and rectify the problem No picture check the PCB to make sure the red power LED is lit If not check that the PSU is correctly connected and has power If you have a test meter verify that the output of the P
20. ition in degrees and the current zoom level ACTION TITLE ON OFF AUTO shows current speed dome action eg PRESET3 PRESET LABEL ON OFF AUTO shows preset title if defined when a preset is called ALARM I O ON OFF shows real time status of the alarm inputs and outputs SET DATE CLOCK sub menu to change the date and time PRIVACY ZONE sub menu to setup the speed dome privacy zones Highlight the item to modify and key NEAR Use the joystick to change the setting and key NEAR to save or FAR to cancel Note If the auto option is chosen the relevant information is displayed for a few seconds before disappearing Set date clock SET DATE CLOCK gt DATE 07 JAN 2007 CLOCK 14 37 15 From the display setup menu use the joystick to highlight SET DATE CLOCK and key NEAR Highlight the item to modify and key NEAR Move the joystick up and down to change an individual value and left and right to move to the previous next value Key NEAR to save or FAR to cancel Privacy zone PRIVACY ZONE 2MASK NO DISPLAY CLEAR MASK EDIT MASK gt From the display setup menu use the joystick to highlight PRIVACY ZONE and key NEAR MASK NO 1 4 shows the privacy zone currently being modified DISPLAY determines whether the privacy zone is displayed during normal operation EDIT MASK allows the operator to define the privacy zone Highlight the item to m
21. odify and key NEAR Use the joystick to change the setting and key NEAR to save or FAR to cancel Edit mask EDIT MASK 1 MOVE TO TARGET POSITION NEAR SELECT FAR CANCEL From the privacy zone menu use the joystick to highlight EDIT MASK and key NEAR Use the joystick to move the speed dome to the approximate position and zoom level for the privacy zone and key NEAR to select or FAR to cancel and return to the privacy zone menu EDIT MASK 1 ADJUST MASK WIDTH 4v ADJUST MASK HEIGHT NEAR SAVE FAR CANCEL Move the joystick left and right to finely adjust the width of the privacy zone and up and down to finely adjust the height To save the privacy zone key NEAR or key FAR to cancel Dome camera setup DOME CAMERA SETUP gt lt CAMERA SETUP lt MOTION SETUP lt PRESET SETUP VST SETUP PATTERN SETUP GROUP SETUP From the main menu use the joystick to highlight DOME CAMERA SETUP and key NEAR CAMERA SETUP setup of specific camera module features lt MOTION SETUP setup of the pan tilt zoom operation of the speed dome park action configuration and configuration of the alarm inputs PRESET SETUP full management and programming of individual presets VST SETUP full management and programming of VST functions PATTERN SETUP full management and programming of pattern tours GROUP SETUP full management and programming of
22. options SYSTEM INFORMATION Provides information such as firmware version protocol and ID values as defined by the dip switch settings DISPLAY SETUP Allows the operator to specify which On Screen Display information is shown during normal operation Also allows privacy zones to be defined and time date to be changed lt DOME CAMERA SETUP Allows all operating features of the speed dome to be programmed and managed Also allows settings for the camera module to be changed PASSWORD SETUP Allows a password to be set to protect the speed dome setup SYSTEM INITIALISE gt Allows various speed dome settings to be reset to factory defaults System information SYSTEM INFORMATION FIRMWARE VER 1 7723 COLOUR SYSTEM PAL PROTOCOL PELCO D ADDRESS tA BAUD RATE 2400 gt BACK EXIT From the main menu use the joystick to highlight SYSTEM INFORMATION and key NEAR To return to the main menu highlight BACK and key NEAR To exit the setup menu completely highlight EXIT and key NEAR Display setup DISPLAY SETUP 2CAMERA ID PTZ INFORMATION ACTION TITLE PRESET LABEL ALARM I O DATE CLOCK lt SET DATE CLOCK gt lt PRIVACY ZONE gt BACK EXIT From the main menu use the joystick to highlight DISPLAY SETUP and key NEAR CAMERA ID ON OFF shows camera ID according to the DIP switch settings eg CAM 1 PTZ INFORMATION ON OFF AUTO shows the current pan tilt pos
23. orrect password must be entered to access the speed dome setup menus EDIT PASSWORD allows the current password to be changed Edit password EDIT PASSWORD 1234567890 ABCDEFGHIJ KLMNOPQRST UVWXYZabcd efghijklmn opqrstuvwx yz lt gt Backspace Space From the password setup menu use the joystick to highlight EDIT PASSWORD and key NEAR The solid white square shows the current cursor position This flashing white square shows the currently selected character Move the joystick up down left right to choose the required character and key NEAR to insert it in the password The solid white square moves to the next cursor position Repeat until password entry is complete If a mistake is made use the joystick to select the backspace and key NEAR The cursor moves back one square Select OK to save the password or CANCEL to lose changes and key NEAR to exit Remember When CHECK PASSWORD is set to ON each time the operator attempts to enter the speed dome setup menu the above screen will be displayed The correct password must be entered to continue with menu setup System initialise SYSTEM INITIALISE 2CLEAR ALL DATA CLR DISPLAY SET CLR CAMERA SET CLR MOTION SET CLR EDIT DATA REBOOT CAMERA REBOOT SYSTEM BACK EXIT From the main menu use the joystick to highlight SYSTEM INITIALISE and key NEAR CLEAR ALL DATA selecting this option will perform a full
24. trol equipment used reference may need to be made to the manual supplied with your particular control equipment Understanding the On Screen Display OSD ACTION TITLE Shows current speed dome action PRESET LABEL If defined is displayed when a preset position is called RECEPTION PRESET3 DATE CLOCK Shows current time and date n active 07 JAN 2007 0 23 09 37 15 I 12345678 CAM 1 307 46 x3 ALARM I O Shows which alarm inputs and outputs are Programming calling and deleting presets SET PRESET1 0 I 12345678 325 37 x1 To program a preset position move the speed dome to the desired scene and zoom level and press SET XXX ENTER Where XXX is a preset number between 1 amp 128 but note that preset 95 is reserved and cannot be used Confirmation is displayed on the OSD To delete a preset position press CLEAR XXX ENTER Where XXX is a preset number between 1 amp 128 but note that preset 95 is reserved and cannot be used The preset position is cleared from memory PARKING BAY 1 PRESET3 07 JAN 2007 2 12 42 22 I 12345678 CAM 1 325 37 x3 To go to a preset position thats already been programmed press PRESET XXX ENTERXXX Preset Where XXX is a preset number between 1 amp 128 but note that preset 95 is reserved and cannot be used The speed dome moves to the preset
25. vice or repair the speed dome as opening or removing covers may expose dangerous voltages or other hazards Refer all servicing to qualified service personnel Key features Presets Up to 127 sets of positional and zoom level information can be stored as presets These can be called manually by the operator automatically by an alarm input or grouped to form a sequence of actions to run automatically Each preset can also be programmed with the following Alarm action relay outputs can be triggered when particular presets are called Title each preset can be titled with up to 10 characters so that zones can easily be identified Pattern tours Any dome movement can be recorded and subsequently played back as four separate pattern tours These can be played back individually or grouped to form a sequence of tours Variable speed tracking between 2 presets VST is a useful feature when for example the operator wishes to patrol a perimeter fence If one preset is defined at one end of the fence and a second preset is defined at the other the VST function will smoothly and accurately move from one end to the other and then back again in a repeating sequence Speed can be adjusted as necessary and up to 8 VST functions can be defined Group function The group function is a powerful feature which allows the operator to define a sequence of speed dome actions to form an automatic patrol sequence Actions can
Download Pdf Manuals
Related Search