User Manual and Parts Book Speed
Contents
1. aap 6 1 0 TECHNICA DATA 8 2 0 1 8 3 0 FIRST INSTALLATION TAKING THE MACHINE OFF THE PALLET 8 4 0 ATTACHING THE TOWING VEHICLE 10 5 0 ADJUSTING THE WORKING DEPTH OF THE 11 6 0 TRANSPORTING THE 12 7 0 USING THE SPEED BRUSH isssiccsccaicicncciinecncedscientutesncatudscvantndecudsandncventsteaens 12 8 0 START STOP PROCEDURE 12 9 0 DISCONNECTING THE 5 13 10 0 TROUBLE SHOOTING PROBLEM ANALYSIS 14 11 0 MAINTENANCE amanaia 15 12 0 TENSIONING THE 16 13 0 SETTING THE BRUSHES UNDER ANGLE 17 1 0 TECHNICAL DATA Speed Brush 1400 Working width 1 4m 55 1 Speed Up to 15 km h2. Brush 2 Drive to the spot where the processing should take place 3 Set the working depth of the machine statically as described in Chapter 5 Make sure that the combination is blocked well and cannot move on its own accord 1 Switch off the towing vehicle before descending 4 Drive slowly lower the brushes and then increase the speed Stopping occurs as follows 1 Brake slightly 2 Lift the brushes to the top position while driving slowly 3 Drive to the next location and start the operation as described above 12 9 0 DISCONNECTING THE SPEED BRUSH The machine can be detached from the towing vehicle in the following manner 1 5 Drive the Speed Brush to a parking area with a firm flat surface I Make sure that the towing vehicle is blocked well and cannot move its own accord 11 Switch off the towing vehicle before descending Ensure that the brushes are raised Detach the Speed Brush from the towing vehicle Make sure that the machine cannot move on its own accord by blocking the wheels l Make sure that the Speed Brush stands stable and cannot roll away and or slide off Start the vehicle and begin to drive For more efficient storage 1 Disconnect the tow bar 2 The Speed Brush can now be stored vertically by tilting it This is the reverse of the description in Chapter 3 without the pallet When putting away the machine it is advised not to have th
3. hours new or repaired Check for loose bolts nuts Check the tension of the chains Tighten loose bolts nuts with the correct tightening moment If necessary adjust the tension of the chains see Chapter 12 After every 50 working hours or annually Check the roller bearings and the driveline Check the chains Check for loose bolts nuts Check the tension of the chains wear amp tear Use EP2 grease Keep the chain clean and use chain spray for lubrication Tighten loose bolts nuts with the correct tightening moment Adjust the tension of the chains see Chapter 12 or if necessary replace the chains chain wheels 15 12 0 TENSIONING THE CHAINS The Speed Brush is standard equipped with adjustable chain wheels that keep the chains taut Depending on the intensity of using the machine the driveline could be affected by wear and tear Then it can occur that the chain no longer has the correct tension and should be tensioned again Figure 11 The tensioning procedure is as follows I Make sure that the Speed Brush is blocked well and cannot move its own accord 1 Remove the safety guards 1 Figure 11 2 Loosen the nuts in the roll and tension the chain Figure 11 3 Place the safety caps back 16 13 0 SETTING THE BRUSHES UNDER AN ANGLE The brushes can be set under an angle so that any accumulated material sand rubber etc
4. is always collected at one side of the machine By driving in circles all material can be easily brushed in Setting the brushes under an angle is done as follows Figure 12 l Make sure that the Speed Brush is blocked well and cannot move its own accord 1 Ensure that the brushes are raised 2 Loosen the bearings at the side where the brushes are not propelled 3 Push the bearing through the recess until the desired position is achieved 4 Tighten the bearings Eil of Figure 12 17
5. the pallet of approx 50 mm 2 off the ground Make sure that the machine is standing on the edge of the pallet Lower the machine controlled and calmly until it stands completely on the ground 1 CAREFUL THE MACHINE CAN SLIDE 6 Unscrew the four bolts 1 to loosen the pallet Figure 7 and subsequently remove the pallet Figure 7 7 Attach the tow bar Figure 8 2x Bolt M12x75 2x Self lock nut M12 Figure 8 8 Attach the machine to the towing vehicle see Chapter 4 0 Use the proper towing vehicle please refer to specifications 4 0 ATTACHING THE TOWING VEHICLE Checking procedure before starting to attach the Speed Brush 1 Check the Speed Brush for visually discernable damage and repair this if safe operation of the machine is no longer guaranteed 2 Check whether all the nuts and bolts are tight 3 Check whether all safety stickers are present on the machine and are not damaged NEVER use the machine without these items Figure 9 If the towing vehicle has a tow hook the Speed Brush can be attached to this vehicle Figure 9 The procedure is as follows 1 Carefully drive the vehicle in reverse until the tow hook is near
6. 9 3 mph Working speed The working speed depends on the conditions and the required result It is maximum 15 km h 9 3 mph Capacity Maximum 21 000 2 22 6042 ft hour Weight in kg 181 kg 399 105 Width 1 770 mm 69 7 Dimensions Height 615 mm 24 2 Length with lifted tow bar 1 640 mm 64 6 Length including the tow bar 2 690 mm 105 9 Requirements for the towing vehicle 12V connection for the electrical cylinder 2 0 GENERAL DESCRIPTION The Speed Brush is a machine for brushing up surfaces such as artificial grass fields natural grounds etc 3 0 FIRST INSTALLATION TAKING THE MACHINE OFF THE PALLET fl The machine is placed vertically on the pallet To remove the pallet and to place the machine Figure 6 horizontally the ground you take the following steps Figure 6 NEVER CRAWL UNDER THE MACHINE Make sure that the cable crane lift can hoist minimum twice the weight of the machine Please refer to Chapter 1 0 Technical Data for the weight details Remove the tow bar from the pallet Attach cables to the upper cross bar of the machine at both sides of the machine Lift the machine including
7. User Manual and Parts Book Redexim Speed Brush Kwekerijweg 8 3709JA Zeist The Netherlands Model 1 400 Tel 31 306933227 31 306933228 Email verti drain redexim com Internet www redexim com Serial number Translation of the original user manual 7 ATTENTION IT 15 OF THE UTMOST IMPORTANCE TO READ THIS USER MANUAL CAREFULLY PRIOR TO USING THE SPEED BRUSH IN ORDER TO USE THE MACHINE SAFELY AND TO OBTAIN THE BEST RESULTS 1307 English 915 120 208 FOREWORD Congratulations on your Speed Brush purchase For safe and long lasting operation of this Speed Brush it is necessary to read and to understand this user manual It is impossible to work safely with this machine without complete knowledge of the content of the user manual The Speed Brush is not a machine that works independently It is the user s responsibility to use the correct tractor The user must also check the tractor Verti Drain Speed Brush combination on safety aspects such as noise level user instructions and risk analysis The following pages deal initially with the general safety instructions Every user should know these safety instructions and apply them At the end of this page a registration card is inserted This registration card should be returned to enable us to deal with potential future claims This user manual lists many instructions that are numbered in sequence You should follow t
8. chine should be professionally adjusted for cultivating the subsoil The manufacturer will not accept any liability for unprofessional use and its resulting damage All risks occurring with this are entirely at the expense of the user Following the use maintenance and repair instructions prescribed by the manufacturer is also considered professional use of this machine Inspect the area to be treated before using the Speed Brush Remove loose obstacles and avoid irregularities The Speed Brush is manufactured according to the latest technical understanding and is safe to use When unskilled people use maintain or repair the machine this could result in injuries to the user and to third parties This must be avoided Always use the Speed Brush in combination with the correct tractor as described in the technical data All persons assigned to operate maintain and repair the Speed Brush by the owner must completely read and understand the operation manual and in particular the chapter of Safety Instructions The user is responsible for a safe Tractor Verti Drain Speed Brush combination This entire combination must be tested for noise safety risk and user friendliness User instructions should also be drafted The user is obliged to check the Speed Brush for visible damage and defects before using the Speed Brush Modifications to the Speed Brush including its operations that have a negative impact on safety must be rectified i
9. e brush touch the subsoil or any other objects in order to prevent the risk of bending the brush hairs 13 10 0 TROUBLE SHOOTING PROBLEM ANALYSIS Problem Possible cause Solution Too much material is kicked up Working depth is adjusted too deep Driving speed is too high Adjust the machine to less depth see Chapter 5 Lower the driving speed Too little material is kicked up Working depth is adjusted too shallow Driving speed is too low Brush is worn out Adjust the machine to greater depth see Chapter 5 Increase the driving speed Replace brush Sloppy image of the field after processing Machine is adjusted too deep Adjust the machine to less depth see Chapter 5 Squeaking noises during the machine s operation Bearings need greasing or are worn out Grease the bearings with EP2 grease or replace them Chains slip over the chain wheels Chains do not have the correct tension Chains chain wheels are worn out Adjust the tension of the chains see Chapter 12 Replace the chains chain wheels 14 11 0 MAINTENANCE Time schedule Check Grease point Method Before every use Check for loose bolts nuts Presence and readability of the safety stickers Figure 6 Tighten loose bolts nuts with the correct tightening moment Replace these if not present or damaged After the first 20 working
10. his sequence A is an indication of a safety instruction note All information and technical specifications provided at the moment that this document is published are the most recent ones Design specifications may be changed without prior notice This document is a translation of the original operating instructions Upon request the original operating instructions are available in Dutch WARRANTY CONDITIONS WITH DELIVERY THIS SPEED BRUSH IS GUARANTEED AGAINST MATERIAL DEFECTS THIS WARRANTY IS VALID FOR A PERIOD OF 12 MONTHS FROM THE PURCHASE DATE SPEED BRUSH WARRANTIES ARE SUBJECT TO THE GENERAL CONDITIONS FOR SUPPLY OF PLANT AND MACHINERY FOR EXPORT NUMBER 188 THAT ARE PUBLISHED UNDER THE AUSPICES OF THE UNITED NATIONS ECONOMIC COMMISSION FOR EUROPE REGISTRATION CARD For your own information fill in the table below Serial number of the machine Dealer name Date of purchase Remarks SAFETY INSTRUCTIONS Figure 1 to the Speed Brush 5 The Speed Brush is designed for safe use This can only be achieved if you completely follow the safety instructions described in this manual Read and understand Figure 1 the manual before you start using the Speed Brush If the machine is not used as described in this manual this can result in injuries and or damage 1 The user must be an expert in using the machine The ma
11. mmediately For safety reasons it is in principle not permitted to make changes or adjustments to the Speed Brush except those approved by the manufacturer If modifications to the Speed Brush have been made then the current CE marking is cancelled The person that has made these modifications has to apply for a new CE marking himself Check the Speed Brush for loose bolts nuts and components before every operation present check the hydraulic pipelines regularly and replace these when the hydraulic pipelines are damaged or appear old The pipelines that are replaced should comply with the technical requirements of the manufacturer hydraulic installation is present you should always make it pressure free before working on this installation NEVER use the Speed Brush in the absence of the safety stickers NEVER crawl under the Speed Brush If necessary tilt the NEVER step off the tractor while the motor is running In case of maintenance adjusting and repairs it is necessary to block the Speed Brush in order to prevent sinking away driving off and or sliding off Always switch off the tractor motor and take the tractor s key out of the ignition in carrying out maintenance adjustments and repairs Figure 2 Figure 2 With regards to the safety of the machine and the user use only original Soeed Brush parts for maintenance and repairs Only authorised technical pers
12. onnel may carry out repairs to the Speed Brush Keep a record of the repair activities The general applicable health amp safety Dutch ARBO regulations must also be followed in addition to the instructions in this user manual Relevant traffic regulations also apply in case of using public roads Transporting persons is not permitted Do not use the Speed Brush in the dark in heavy rain storm or on slopes with an angle larger than 20 degrees All persons that are going to operate the Speed Brush must be familiar with all the functions and control elements of the Speed Brush before starting any work activities Attach the Speed Brush to the towing vehicle according to the regulations Danger of injuries Check whether you have a clear field of vision both close by and far away before you depart Safety stickers Figure 2 3 and 4 with an identical meaning are attached to both sides Figure 5 the Speed Brush These safety stickers must always be clearly visible and legible and must be replaced if they have become damaged During operation NO persons are allowed within danger zone of Speed Brush because there is danger of physical injuries caused by flying particles or substances Figure 3 933 280 402 Figure 3 Figure 4 Keep a distance of minimum 4 metres Figure 4 Pay attention to the permitted lifting capacity of the towing vehicle Dress app
13. ropriately Wear sturdy shoes with steel toecaps long trousers and tie up long hair Do not wear loose clothing Bae 280904 900 280 402 Figure 5 7 Location of the safety stickers Figure 5 Used oil grease is harmful to the environment Dispose of these substances according to the regulations that apply in your location EU DECLARATION We Redexim BV Utrechtseweg 127 3702 AC Zeist Holland declare entirely under our own responsibility that the product SPEED BRUSH WITH A MACHINE NUMBER AS INDICATED ON THE MACHINE AND INDICATED IN THIS MANUAL to which this declaration refers complies with stipulation of the 2006 42 EC machine directive Zeist 22 02 12 A C Bos Manager Operations amp Logistics Redexim Holland TABLE OF CONTENTS USER MANUAL AND PARTS BOOK 1 PORE WORD its sicssiitusis teas ctansathetonsaasuadnvaseutinentsataecahsusinaedsvidaestcudinwaddutdnenseudienabnutuennanes 2 WARRANTY CONDITIONS ii sccseccscsssesctcccicraseceseiutenciedevscuseccieactesedasusrasteadivnetadserateneces 2 REGISTRATION CARD 2 EU DECLARATION
14. sporting the Speed Brush in back of the towing vehicle over public roads Verify the national legislation regarding the regulations On open fields while the brushes are raised the maximum speed is 15 km h 9 3 mph if circumstances permit this A higher speed can be dangerous for the driver and or the public and can even damage the machine A Ensure that the brushes are raised during transport 7 0 USING THE SPEED BRUSH Before using the Speed Brush in a location you should check the following items 1 Are there loose objects in the field First remove these objects Are there slopes The maximum slope is 20 degrees for this machine Is there danger of flying objects e g balls that distract the attention of the driver If so the Speed Brush CANNOT be used 4 Is there danger of sinking sliding away If so postpone the processing until conditions improve 5 If the soil is wet postpone the activities until conditions improve 6 Do not make sharp turns it is better to drive in straight lines or in circles 8 0 START STOP PROCEDURE The start procedure is VERY important If this procedure is not executed as described below it might result in serious damage to the machine The start procedure is as follows 1 Check the Speed Brush for loose components and look whether all components function properly l If loose components are observed or components do not function properly the problems must be solved before using the Speed
15. the Speed Brush Make sure that the towing vehicle is blocked well and cannot move its own accord 11 Switch off the towing vehicle before descending 2 Attach the Speed Brush to the vehicle and check that it cannot detach from it 3 Subsequently check whether the Speed Brush is in a horizontal position If not you can adjust this by unscrewing the two bolts and selecting a higher or lower position Figure 9 4 Finally connect the electrical cable to the battery of the vehicle and if necessary lift the brushes using the electrical switch box 10 5 0 ADJUSTING THE WORKING DEPTH OF THE BRUSHES Adjusting the height setting will change the working depth of the brushes DETAILB Jf SCALE 2 5 jf A sif Figure 10 The procedure is as follows A Make sure that the towing vehicle Speed Brush is blocked well and cannot move on its own accord Switch off the towing vehicle before descending Lift the brushes to the top position using the electrical switchbox 2 Remove the R clip out of the pin 1 Figure 10 3 Set all four sides of the machine at the same height so that it is possible to treat the field as evenly as possible NEVER adjust the machine in such a way that it could damage the subsoil I IMPORTANT First check the working depth on the subsoil statically before using the machine 11 6 0 TRANSPORTING THE SPEED BRUSH The user is responsible for tran
Download Pdf Manuals
Related Search