USER MANUAL HELIOS 151.566UK
Contents
1. for safety Do not stare to the light The symbol _ m determines the minimum distance from lighted objects The minimum distance between light output and the illuminated surface must be more than 0 1m 5 Connect with power supply The ground wire must be connected Use the plug to connect to the main power supply as following 6 Quick Trouble Shooting 7 1 if the unit is not functioning Check if mains power is on and fuse is OK 7 Replacing Fuse Disconnect from the main power supply first then remove the fuse holder above the IEC Socket to reveal the fuse Replace the correct fuse rating as stated on lighting or user manual Then lock the fuse holder cover back into place atxlight s User manual HELIOS 151 566UK 8 General Maintenance To maintain optimum performance and minimize wear fixtures should be cleaned frequently Usage and environment are contributing factors in determining frequency As a general rule fixtures should be cleaned at least twice a month Dust build up reduces light output performance and can cause overheating This can lead to reduced lamp life and increased mechanical wear Be sure to power off fixture before conducting maintenance Unplug fixture from power Use a vacuum or air compressor and a soft brush to remove dust collected on external vents and internal components Clean all glass when fixture is cold with a mild solution to a cloth or tissue and drag dirt and gr2. gtxlight USER MANUAL HELIOS 151 566UK User manual HELIOS 151 566UK HELIOS For indoor use only Caution Please read this manual carefully before operating AN Damage caused by misuse is not covered by the warranty 1 General Introduction Thank you for choosing the QTX Light Helios This product meets the requirement of the European guidelines CE The Helios is designed to produce light effects for use in light show systems in bars clubs schools stages etc Features 4 Operation modes Automatic running DMX Sound Active Master Slave up to 4 slaves Sound active from built in programs Gobo rotation via LED matrix Strobe effect with adjustable speed IEC Daisy chain function for power loop MKII Version only Long life LED light source no light bulbs to replace Razor sharp beams Colors don t fade in time Very little heat production Very low power consumption Lightweight and easy to transport 2 Package Contents Please check the contents to ensure that the product has been received in good condition Light x 1 unit User manual x 1pcs If you find any accessory is missing or the lighting has arrived with any problems please contact your retailer at once Do not try to fix this item yourself or you will lose the warranty Please keep the original package and invoice for any possible replacement or returned demand 3 Installation Every person involved with the installat
3. ime to the outside of the lens Gently polish optical surface until they free of haze and lint The cleaning of internal and external optical lenses and or mirrors must be carried out periodically to optimize light output Cleaning frequently depends on the environment in which the fixtures operates damp smoky or particularly dirty surroundings can require cleaning fluid Always dry the parts carefully Clean the external optics at least every 20 days Clean the internal optics at least every 30 60 days 9 Mounting instruction The fixture may be mounted in any position provided there is adequate room for ventilation It is important never to obstruct the fan or vents pathway Mount the fixture using a clamp Adjust angle of the fixture loosening both knobs and tilting the fixture After finding desired position retighten both knobs When selecting installation location take into consideration lamp replacement access and routine maintenance Safety cables must always be used Never mount in places where the fixture will be exposed to rain high humidity extreme temperatures changes or restricted ventilation 10 Layout for the HELIOS 1 Mounting Bracket 2 Thumb Screw 3 Lenses 4 Housing Cover atxlight 4 User manual HELIOS Rear panel DMX occupation 1 Ground 2 Signal 3 Signal Power Input Fuse 5 DMX In connector 6 DMX Out connector 151 566UK DMX IN __ iUMA OUT 7 0 gd HE Oy Control B
4. ion operation and maintenance of this device should be qualified and follow the instructions of this User manual We recommend that this product is not used for audience scanning and should be used within the guidelines of radiation of lasers and LEDs used for display purposes HSG95 When you connect to the main power supply the device will illuminate and the light effect will change with music when in sound activated mode qtxlight 2 User manual HELIOS 151 566UK 4 Caution To prevent Mortal Electrical Risk and Long Life Operation For your safety please kindly pay attention to all of the warnings listed below Always plug in the power plug last and disconnect from the mains when the device is not in use or before cleaning Do not install and operate the device in rain or extreme heat moisture or dusty environments This device is for indoor use only and in a dry environment Do not switch on immediately but wait until it reaches to room temperature if the device has been exposed to drastic temperature fluctuations Do not shake the device and avoid brute force when installing or operating Do not spread the smoke or bubble of effect machine directly to the device Do not use the device during thunderstorms and please disconnect the power Do not use solvents or aggressive detergent to clean the device Use a soft and clean cloth Do not modify the device or the connected power cord without authorization Use appropriate safety rope
5. is only meant for service purposes Please do only use this function if you want to set the unit shortly into standby mode 13 DMX Controlling The control board allows you to set the DMX address which is defined as the first channel from which the Helios LED flower will respond to the DMX controller Please be sure that you don t have any overlapping channels in order to control each Helios LED flower correctly and independently from any other fixture on the DMX data link If two three or more Helios light effects are addressed similarly they will work similarly For address setting press the Mode button 9 until the display 13 shows A001 and set the desired address via the Up 11 and Down 12 button After having addressed the Helios flower you may now start operating these via your DMX lighting controlle r 14 DMX Protocol atxlight User manual HELIOS 151 566UK 15 Disposal Please disposal of the unserviceable device according to the current statutory requirements Technical specification LED 5mm LED LED Type 96 Red 48 Green 48 Blue LED Life 50 000 hours estimate Note Conforms to Laser and LED Safety standard BSEN60825 1 2007 atxlight
6. oard MODE ENTER UP DOWN 7 IEC Power loop out socket MKII Version only 8 Power Socket Fuse holder 9 Mode Button 10 11 12 13 Enter Button A NA Up Button Down Button A NA LED Digital Display 11 Digital Display Setting amp Function MODE ENTER qtxlight DMX Mode 4900 Slave Mode 5 Master Mode b LED Display d l t UP DOWN UP DOWN UP DOWN UP DOWN User manual HELIOS 151 566UK 12 Master Slave operation This function will allow you to link up to 4 units together and operate without a controller The units will be sound activated In Master Slave operation one unit will act as the controlling unit and the others will react to the controlling units programs Any unit can act as a Master or as a Slave Using standard XLR 2 core screened microphone cables daisy chain your units together via the XLR connector on the rear of the units Remember the Male XLR connector is the input and the Female XLR connector is the output The first Helios flower master will use the female XLR connector only the last use the male XLR connector only and a terminator see DMX setting On the Master unit set your desired show with the mode 9 and Up Down 11 12 buttons and set that show by pressing the ENTER 10 button On the slave units set the respective slave mode for all slave devices The slave units will now follow the Master unit Please note The function G 3
Download Pdf Manuals
Related Search