USER MANUAL SECURELINE CASTELLE SAFE
Contents
1. ANCHORING YOUR SAFE In order to fulfill the requirements of the EN certification your safe must be anchored to a suitable wall or floor using the masonry fixing kit supplied 1 Place the safe in the position you have selected Before marking or drilling any holes Secu re E nN ensure that there are no pipes or cables present at the fixing point If there is skirting board present this should be removed to allow the safe to be fitted USER MANUAL flush against the wall 2 Open the safe and remove any shelves SECU RELIN E CASTELLE SAFE 3 Using a pencil or sharp object mark out the position of the two drilling holes use the base or rear holes whichever provide fixing to the stronger Models SL0271 0 SL02711 SL0271 2 SL0271 3 idle SL02714 SL02810 SL02811 SL02812 SL02813 amp 4 Close the safe and remove it to provide sufficient space to drill the fixing SL02814 holes 5 Using a hammer drill drill holes 80mm deep The bolts are 10mm in diameter you will need an 11mm concrete drill bit 6 Clear the drill holes and remove any debris using a vacuum cleaner 7 Secure the safe using the bolts supplied Do this by feeding the bolt directly through the hole in the safe into the hole in the anchoring material Use a socket wrench to fully tighten the bolts in place www Secure Line net USER INSTRUCTIONS fig A rt fig B fig D E OPEN FFNEN OUVERTURE APERTURA OABH2. O xs ADD SECOND USER ZWEITEN BENUTZER ZUF UGEN AJOUTER DEUXIEME UTILISATEUR AGGIUNGA IL SECONDO UTENTE AGREGUE A SEGUH DO USUARIO C e 1 2 3 4 5 6 F 4 5 6 7 8 9 WEll CHANGE CODE CODE ANDERN CODE MODIFICATION CODIFICHI CAMBIARE CIFRE CAMBIAR 0 dale 4 J 2J3JL4JSJ 8 bILILIGILILI bILILILIBILY DELETE SECOND USER ZWEITEN BENUTZER L SCHEN J2 da JJ d 6 Jd d sj JJ J 2 SUPPRIMER DEUXIEME UTILISATEUR CANCELLI IL SECONDO UTENTE 2 JJ WALA press and hold until double signal and lighi stays ON dr ckt halten bis doppel signal und leuchte AN suUbsISance sem e conservazione pemula subsistencia presionada T 6 dt ELECTRONIC LOCK The lock is operates with a numeric six digit code or a word of six letters A secondary code can be added if required Each key press is confirmed with an audio and light signal TO OPEN figure A Enter code the factory code is set as 1 2 3 456 Two beeps will be heard and a green light will flash Turn the D ring handle and open the safe If the safe is not opened within 3 seconds please repeat TO LOCK Close the door and turn the handle fully to the closing position MANIPULATION PROTECTION If four consecutive invalid codes are entered the key pad is blocked for 5 minutes During this period the light will flash every 10 seconds and pressing any key produces a long beep After this 5 min
3. place the 9V alkaline battery Do not use rechargeable batteries
4. ute period entering two more invalid codes restarts this 5 minute blocking period CHOOSING NEW CODES We strongly advise that personal data i e birthdays home telephone numbers etc is avoided and that your code is committed to memory only not written down Change the factory code before you begin using the safe ACTIVATE THE SECOND OPENING CODE Figure B Press and hold key 1 until a double beep is heard The light remains on during the following actions Enter the main code this will be 123456 at the first time of using Enter the secondary 6 digit code twice a double beep will be heard after each time the code is entered The secondary code can be changed in the same way as the main code The main code can delete the secondary code however the main code cannot be deleted CHANGING THE CODE Figure C With the door open Press and hold 0 until a double beep is heard Enter the current code this will be 123456 at the first time of using Enter the new 6 digit code a double beep will be heard Enter the new 6 digit code again a double beep will be heard If an error is made a long beep will be heard and the original code remains active DELETING THE SECOND CODE Figure D Press and hold 3 until a double beep is heard The light remains on Enter the main code the secondary code is deleted LOW BATTERY A series of beeps indicates the battery needs replacing Slide the cover on the bottom of the keypad to the side and re
Download Pdf Manuals
Related Search