LocoCruiser Standard series DCC decoder User Manual
Contents
1. Locotruiser LocoCruiser Standard series DCC decoder User Manual Ver1 0 2012 06 Beet HEHE ANE MODEL 32454 No 9 Lane 675 Sec 2 Nanping RD Pinjin City Taoyuan County Taiwan R O C 886 3 4961368 2658082 www anemodel com service anemodel com Om Before you start to use the decoder please read the following warnings first This product is for all HO scale railroad models use only and a small number of N scale railroad models 2 Please read this manual carefully before installing the decoder 3 Please do not use this decoder under the non DCC control system of model train 4 This product is not suitable for children under 8 years old Improper use may cause injury by 11 sharp points of edges Do not expose the product to the rain humidity fire the direct sunlight and corrosive chemical product The suitable working temperature is 0 80 C Strong electromagnetic wave may interrupt the normal working of the product To avoid over heating do not wrap the circuit broad in insulation tape 10 gt Do not forcedly press or fold the product This product is not waterproof 12 gt 13 gt 14 gt Before installing the decoder make sure to eliminate the static electricity from the installer Before installing the decoder remove the locomotive from the track After installing the decoder make sure that no wires are squeezed or cut LocoCruiser standard series decoder user2. can achieve your needs At the same time each function output has a variety of lighting effects From the simplest on off to a wide variety of lighting performance LocoCruiser Series 2 is your best choice The CV value of various lighting performance are below CV value Function 0 Light on 2 Strobe 4 Mars Light 8 Reverse direction 16 Forward direction 32 1 4 sec flashing A this two effect design for ditch light 64 1 4 sec flashing B this two effect design for ditch light 36 Firebox 69 Warning light 128 1 2 sec flashing 3 5 Programming In some part of DCC controllers there s an individual programming track function To connect the programming track output with single track put the locomotive on this track then you can read and program LocoCruiser Series 2 decoders fully support the programming track function You can read and adjust the CV value of LocoCruiser Series 2 decoders through the programming track and let the Series 2 fully control the features of your locomotive as well LocoCruiser standard series decoder user manual Ver1 0 5 ANETE as running smoothly on your layout 3 6 Operational reliability LocoCruiser Series 2 running decoders have passed extensive testing and functional adaptation It can meet the running performance of most DCC ready locomotives You dont need to make any adjustments In some particular locomotives you may just need to make small adjustmen
3. to program Have a look at the explanations for CV29 in the table in chapter 7 firstly decide which options should be active The column Value has two numbers for each option If the option is switched off the value is 0 Otherwise it is a number between 1 and 128 Add all the values for the respective options to arrive at the correct value for this CV 7 CV value table CV Function Default Range Remark 1 Engine address 3 1 127 2 Start voltage 1 1 CV6 value 3 Acceleration 5 0 255 4 Deceleration 5 0 255 5 Maximum speed 0 CV6 255 value 6 Medium speed 0 CV2 CV5 value CV29val 7 Version number 201 Cannot be revised Wee f adjustment please 8 Manufacturer s ID 45 Cannot be revised see the chapter 5 6 10 EMF Feedback Cut out 255 0 255 17 Extended engine high 192 192 255 address 18 Extended engine low address 0 0 255 19 Consist address 0 0 255 29 Configuration register 6 0 255 7 1 Light function Function Default Range Record your number in here Remark 33 FOF on off 1 34 FOR on off 2 gt 35 F1 on off 4 4 36 F2 on off 8 37 F3 on off 16 ae 95 F4 on oft 32 49 FOF light effect 16 0 255 50 FOR light effect 8 0 255 51 F1 light effect 0 0 255 52 F2 light effect 0 0 255 53 F3 light effect 0 0 255 LocoCruiser standard series decoder user manual Ve
4. value of CV1 and check if the engine address is different from the Decoder Rewrite the engine address 9 5 When I use the consist address to control the loco have changed the value of CV17 amp CV18 But I still can t control the loco Please check the CV29 bit 5 value If the value of bit 5 is not 1 please change to 1 9 6 I have followed the manual to do but still have problems not included in the manual What can do If you still can t solve the problems please contact us via E mail or telephone we will reply to you as soon as possible Appendix Il Repair information ANE Model provides you with the warranty and service for LocoCruiser standard series decoder as the following 1 gt The LocoCruiser standard series decoder is replaced free of charge within 90 days and repaired free of charge within one year after purchasing 2 After the free of charge repair period one year the LocoCruiser standard series Decoder provides a lifelong repair service with charge LocoCruiser standard series decoder user manual Ver1 0 17
5. 17 amp CV18 and the Engine address CV1 if the value of the Extended engine address is not 0 and the value of bits of CV29 is 1 the locomotives will be under the control of the Extended engine address If the value of the Extended engine address is 0 or the value of CV29 bit5 is 0 the locomotives are under the control of the Engine address Chapter 6 of this manual will show you the CV values You can find the CV values which related to the engine address The range of CV19 value that responds to the Consist address is from 1 to 127 and from 129 to 255 If the value of CV19 is larger or equal to 1 and is smaller and equal to 127 the locomotive will agree with forward direction At this time the locomotive is under the control of the address 1 127 If the value of CV19 is larger or equal to 129 and is smaller and equal to 255 the locomotive will accept the opposite direction At this time the locomotive is under control of the address CV19 value 128 The range of the Extended engine address CV17 amp CV18 value is 128 9999 The value is according to the value of the lowest 6 bits of the CV17 combines with the 8 bits of CV18 LocoCruiser standard series decoder user manual Ver1 0 5 5Light effect 5 5 1 Turn on off light The LocoCruiser standard series Decoder is equipped with 5 fixed lighting outputs relative values are stored in CV33 to CV37 The table 4 1 shows their default settings Gm CV Functi
6. 4 3 Installation recommendations We strongly recommend modellers confirm that the locomotive will operate normally before installing the decoder Also the decoder can be tested for operation by using a Decoder Testing Board This can avoid problems before installation of the decoder 4 4 Locomotive with 8 pin DCC standard Interface According to the instructions in the locomotive manual remove the body shell and find the 8 pin socket First remove the dummy plug from the socket and find the correct direction to insert the decoder plug Usually there s a number or arrow marked pin 1 on the 8 pin socket And then fit with 8 pin head you ll finish the installation The wire color comparison table of 8 pin DCC standard interface LocoCruiser standard series decoder user manual Ver1 0 7 ANETE No Color Connect 1 Orange Motor 2 Yellow Rear light 3 Empty Empty 4 Black Left track 5 Gray Motor 6 White Front light 7 blue Common pole 8 Red Right track 4 4 1 Wiring Diagram for LocoCruiser LC201 AUX1 Head L nl Light black red orange motor 4 5 Locomotive with 6 pin DCC standard Interface Please check the wire colors are connected to the correct parts of the locomotive Colour Details Orange Motor 2 Yellow Rear Light 3 Empty Empty 4 Black Left Rail 5 Gray Mo
7. E 9 5 Initial operation E 9 BA DOG MOOG EE E E CASEL SEENEN eege 9 5 1 1 DCC Speed Steps flashing Iobte t A 9 5 2 Speed COMO acs EE 9 5 2 1 Speed curve setting Factory Default essegeugeieueeroesgeeee d un eegsSEuEe eege EEN 9 5 2 2 Speed table MOG c ece2scccieevetceveeje daha senYobeceeacutnateecveegedesGbuhevedhueeaeseechestelsidedeceesonstebaseceeceeeeet 10 5 2 3 Speed model Exchange egen gegen enee tinea teas itdiensssidiedisi hae di Hae dE Ee 11 5 2 4 Acceleration amp Deceleration Ask 11 5 3 DO COMMON seisein eraa ee EE eae AEE aaa raK EEEE aaar aKT penaa e EAE A aai 11 5 3 1 DC control method irie eena aner aeaa alae heed a a LARENSE r a tie 11 5 4 Engine address e EE 11 54 1 Nee 11 5 4 2 Locomotive engine address Setting sssssssssrrssrrrressrrnrsrttnrantntnnttrnnntttnanattanantntananennnntnenna 11 SO ele 12 5 5 1 Turm Omot MQW ss gege irissen due ENEE EES NEES dE aaa 12 5 9 2 OM EE 12 SC CV29 ne TEE 12 6 Decoder Settings Programmimg NENNEN ENEE 13 6 1 Configutation Variables CN 13 6 1 1 Standardisation in the NMRA nen 13 6 1 2 Ee 14 LocoCruiser standard series decoder user manual Ver1 0 KEE WANG e E 14 FA ie ul nne EE 14 Te opeed tables ratoineen eege Eed dese Ee 15 8 DISCIOSUPE ANNOUNCE secsivesscccexescecevede ous wens ENEEEEE esl sapteacdevey ass ehuseakedveesacchntneeavavdeealeueii steeexuesiatenyebecaee 15 9 Troubleshooting rera airna raa ETE AAE Ea aLa EKAA ENEI OE aN Ena
8. are designed by the locomotive manufacturers to operate at full soeed at 12 volts DC on the track LocoCruiser recommends running your DCC command station and boosters at the lowest track voltage possible that provides acceptable operation The N Scale 12 V setting on LocoCruiser equipment works for most HO SN scale layouts Some DCC systems made by other companies supply more voltage to the track and are not adjustable If the track voltage applied exceeds the operating parameters of the locomotive and ist lamps it is possible for overheating to damage your locomotive whether you use DC or DCC For example running an N Scale lovomocite that was designed to run on 12 14 volts on a sstem that supplies 12 or more volts to the track may cause overheating and damage to the locomotive its shell and your decoder 4 1 2 Recommended tools for decoder installation You ll need a few simple tools when you begin installing decoders LocoCruiser standard series decoder user manual Ver1 0 Gm 1 A soldering iron preferably temperature controlled Though many installations do not require soldering you may still need to use a soldering iron to install extras like lamps for special lighting effects Solder Oo Jo PF wh A small screwdriver for disassembling your loco Small diagonal cutters for cutting amp stripping small wire Tweezers to pick up small loco parts Heat shrink tubing for protecting wire connections this is better than elect
9. da ENTEL EESE 16 9 1 The Decoder is installed After electrified the lights do not work and the locomotive does not move after changing Speed ek 16 9 2 During the locomotive moving the moving iS NOt CONTINUOUS sessseessseieeseriererrireeerirrerrrrresrrenn 16 9 3 The locomotive runs normally but the lights do NOt work eeeeeeeeeenneeeeeeneeeeeeeneaeeeeeseeeeeeeeas 16 9 4 Headlights work but the locomlotive does NOt move 16 9 5 When I use the consist address control the loco have changed the value of CV17 amp Cv18 But I still can t control the lOCO sccccice scccecesveqees ses seces cadacvex seosurstdencudyescocuiseeseevensssoseessiaedvegesseveus arenes 16 9 6 have followed the manual to do but still have problems not included in the manual What can ee EE 16 Appendix Il Repair infO rations a 5cvevdecis cs ebeeeidvsccun ec ca ssdecevvcvexetedes sauces vines es aus heededcserenes acteceeeestatenedeevexe 16 LocoCruiser standard series decoder user manual Ver1 0 3 Zen 1 Introduction Congratulations for choosing the ANE MODEL LocoCruiser Standard series decoder It is designed ANE MODEL mobile decoder is suitable for all HO scale and some N scale locomotives with space for installation to give you exciting DCC control features at a reasonable price LocoCruiser Standard decoder compliments the excellent properties of their predecessors and expand their capabilities with extra functions It supports
10. e deceleration is determined by the value of CV4 The higher the acceleration CV3 deceleration CV4 value the higher the final acceleration deceleration That is to say the acceleration deceleration speed of the locomotive is lower The lower the value is the lower the final acceleration deceleration is That is to say the acceleration deceleration speed of the locomotive is higher 5 3 DC control 5 3 1 DC control method Using a conventional DC controller to operate is possible without any problem You can run a locomotive that already has the ANE MODEL LocoCruiser Standard series decoder installed on 16VDC track DC environment does not support Back EMF function and lighting effect 5 4 Engine address setting 5 4 1 Engine address The engine address indicates the assigned numbers of the moving locomotives on the track Setting the engine address will enable you to control the locomotives by the DCC controller The following describes show the definitions of DCC protocol s engine address CV1 Engine address CV17 amp CV18 Extended engine address CV19 Consist address The priority of the 3 engine addresses which are defined in the DCC protocol is Consist address gt Extended engine address gt Engine address 5 4 2 Locomotive engine address setting The first priority is the Consist address of CV19 The locomotives are under the control of the Consist address unless the value is 0 or 128 As for the Extended engine address CV
11. et accordingly If this is not the case the following problems may Occur 1 You cannot switch the lights with FO at all 2 The lights keep switching on and off dependent on the speed step In this case make sure that the speed step settings of decoder and command station are the same 5 2 Speed control There are two speed control settings the speed curve setting and the speed table setting 5 2 1 Speed curve setting Factory Default The speed curve setting is to set the starting voltage in CV2 the maximum voltage in CV5 and the medium point voltage in CV6 In order to explain more the speed step and the speed value are represented with a curve in an axis graph In the following 4 figures from 4 1 to 4 4 the horizontal line represents the speed step while the vertical line represents the speed value The speed of the locomotive is divided into 28 steps in the speed step line Thus each step represents one speed step and the value is from 0 to 28 The speed value is the current speed of the locomotive and the value is from 0 to 255 The 14 step and the 128 step settings are similar with the curves The 14 step speed setting is 14 the middle speed will be 7 step on the other hand when the loco is under 128 step speed the middle speed will be 64 step LocoCruiser standard series decoder user manual Ver1 0 Om 256 256 maximum voltage maximum voltage medium point 128 voltage 128 medium point voltage star
12. figuration Variable and indicates that the storage cells described above are not only variable but they also determine the behavior of the decoder 6 1 1 Standardisation in the NMRA The NMRA National Model Railroad Association has defined which CVs determine certain parameters of a decoder The DCC standard allocates fixed numbers for certain CVs adherence is obligatory This greatly simplifies things for the user since decoders of most manufacturers comply with this standard and therefore dealing with CVs requires the same process with the same CV numbers regardless of the manufacturer The DCC concept permits to enter numbers ranging from 0 to 255 into CVs Each CV carries only one number While the position number is predetermined the range of values may vary LocoCruiser standard series decoder user manual Ver1 0 im Not all CVs must accept values ranging from 0 to 255 The permitted values for LocoCruiser decoders are listed in the table in chapter 7 showing all available CVs 6 1 2 Bits and Bytes Most CVs contain numbers CV1 for instance contains the locomotive address This can be any number between 1 and 127 While most CVs expect numbers to be entered some others are rather like a collection point of various switches that administer different functions in one CV mainly on or off CVs29 and 49 are good examples you must calculate the value for these CVs yourself The value depends on which settings you want
13. manual Ver1 0 1 ANETE Contents Warning DEE 1 Ela 2 1s a ole Te le EE 3 2 LocoCruiser Standard decoder Series 2 3 3 General Properties of all Decoderg AA 4 3 1 Operating Bee EE A ee ein e EE A gS Analogue MOUS EE A 3 4 ele A deele TC in ue WEE 5 3 6 Operational liability sczsescedeesexavceceesyheneevavedate aeea aAa a aa aaa Ni anaoa aA aana a aa aaas 5 AE EO EE 5 4 1 Ten Steps for successful decoder mstallaton ccc eects eeneeeeeeeeeeeeeeeeeaeeeeeeaeeeeeenaeeeeeneaeeeeees 5 4 1 1 Avoiding heat problems with decoder installations A 5 4 1 2 Recommended tools for decoder installation eccceeeeeeeeeeseeeeeeeeeneeeeeeeneeeeseeneeeeeeseeeerenaes 6 4 2 Requirements for metallaton cece eeeeeeeeeeeneeeeeeeneeeeeeeneeeeeeseaeeeeeeeaeaeeeeeaaeeeeseaaeeeeteaaeeseeseaeeeeees 6 4 3 Installation recommendations 0 eceeeeesseeeeeseeceeeeeeeneceeneeeceseeeeneeeeenanaeneseeaeeesesaaeeneenaeeneneseaeeetens 6 4 4 Locomotive with 8 pin DCC standard Interface 6 4 4 1 Wiring Diagram for LocoCruiser LC 201 7 4 5 Locomotive with 6 pin DCC standard Interface 7 4 5 1 Wiring Diagram for LocoCruiser LC 202 8 4 6 Locomotive with 21 pin DCC standard Intertace A 8 4 6 1 Wiring Diagram for LocoCruiser LC202 nnen 8 4 7 Connecting Additional Functions eee eeeeeeeeeeeeeeeneeeeee eee ee eeseaeeeeeeeaeaeeeeeeaeeeeseaaeeeeeenaeeeenneaeeeete 8 4 8 Suitable Light Bulbs iseis siete iene adnan ati dete ae 9 4 9 Suitable IOCOMOLVE ly Pe E
14. on Default Range 33 FOF on off 1 34 FOR on off 2 2 35 F1 on off 4 Bi 36 F2 on off 8 16 37 F3 on off 16 32 128 95 F4 on off Not yet open Table 4 1 Lighting output on off allocation FOF is front light and FOR is rear light Note Value 1 control by F1 Value 2 control by F2 Value 16 control by FO Value 128 always light on 5 5 2 light effect The CV33 CV34 values just effect the turn on or off status The However the LocoCruiser standard series Decoder is featured with 10 lighting effects including the dimmer the warning effect the blinking per speed effect the random blinking effect the strobe light effect and 3 fixed frequency blinking effects Understanding more about the CV49 to CV53 will help you adjusting the CV settings to bring you more than one thousand of lighting effects 5 6 CV29 setting Table 4 2 Light effect allocation The information of CVs outputs and light effects are shown in table 4 3 as below CV Function Default Range necord oe in 49 FOF light effect 16 0 255 50 FOR light effect 8 0 255 51 EI light effect 0 0 255 52 F2 light effect 0 0 255 53 F3 light effect 0 0 255 96 F3 light effect aan 0 255 CV29 related to the operating efficiency of the decoder The performance of every bit switch will have a significant impact on the decoder In order to allow the modelers can easily adjust each bit of CV29 we make list of CV29
15. r standard series decoder user manual Ver1 0 Om 3 General Properties of all Decoders 3 1 Operating Modes With the locomotive running on the layout and if you need to adjust some CV values you don t have to move the locomotive to the programming track you can adjust it through DCC controllers OPS mode Operating mode by calling up the number of the locomotive then modify the CV value directly There s one thing you need to note OPS mode can only set the function of the decoder It can t read the CV value of the decoder If you need to adjust the CV value precisely then we suggest you to move the locomotive to programming track to read and program 3 2 Motor Control In order to provide more perfectly running performance ANE MODEL manufacture LocoCruiser Series 2 especially designed a motor control program with Back EMF function For a variety of locomotives the motor will adjust output control automatically so modellers can experience speed control and silent running with a high standard 3 3 Analogue Mode According to the setting of CV29 LocoCruiser Series 2 provides you a dual mode with the loco decoders able to run under DCC or DC control This eliminates having to go to the trouble of temporarily removing the DCC decoder 3 4 Functions LocoCruiser Series 2 has 4 6 function outputs Each function output can reach the maximum current of 300mA no matter weather you are controlling incandescent light bulbs or LEDs it
16. r1 0 15 d 96 F4lgbteitec 0 0 255 7 2 Speed table Function Default Range Remark 67 Speed Table 1 1 0 255 68 Speed Table 2 6 0 255 69 Speed Table 3 12 0 255 70 Speed Table 4 16 0 255 71 Speed Table 5 20 0 255 72 Speed Table 6 24 0 255 73 Speed Table 7 28 0 255 74 Speed Table 8 32 0 255 75 Speed Table 9 36 0 255 76 Speed Table 10 42 0 255 77 Speed Table 11 48 0 255 78 Speed Table 12 54 0 255 79 Speed Table 13 60 0 255 80 Speed Table 14 68 0 255 81 Speed Table 15 76 0 255 82 Speed Table 16 84 0 255 83 Speed Table 17 92 0 255 84 Speed Table 18 102 0 255 85 Speed Table 19 112 0 255 86 Speed Table 20 124 0 255 87 Speed Table 21 136 0 255 88 Speed Table 22 152 0 255 89 Speed Table 23 168 0 255 90 Speed Table 24 188 0 255 91 Speed Table 25 208 0 255 92 Speed Table 26 230 0 255 93 Speed Table 27 252 0 255 94 Speed Table 28 255 0 255 8 Disclosure announce This warranty excludes the LocoCruiser standard series Decoder malfunction under the following reasons e User does not follow the instructions to install the Decoder causing the product to be damaged or malfunction User does not follow the instructions to operate the Decoder and make the product damaged or malfunction User disassembles or replaces the component of the product by himself then makes the product damaged or malfunction The product is corroded igni
17. rical tape Tape for securing wires and the decoder inside the locomotive Decoder installation should be done in a reasonably static free environment We recommend that you do all installations on a nonmetallic surface LocoCruiser decoders are not overly sensitive to static electricity amp with a little common sense you won t have problems 4 2 Requirements for installation ANE MODEL Series 2 decoders are mainly designed for OO HO scale 1 76 1 87 locomotives and railcars The different connections are listed below The type of decoder Statements LC201 With NMRA Medium 8 pin plug apply to the locomotive with NMRA 8 pin socket LC202 With 9 NMRA standard wiring so modellers can solder directly to the locomotive wiring LC203 With NMRA 21pin socket apply to the locomotive with 21pin plug Board replacement type decoder suitable for most locomotives which has LC204 lack of internal space such as ATLAS Athearn KATO USA and KATO Japan locomotives These are exclusive for UK with 21pin socket If you are interested please LC205 E contact our UK distributor LocoLine The exclusive sale for UK with 8 pin socket decoder If you are interested LC206 ge please contact with our UK distributor LocoLine These three types of decoder have a standard NMRA JST 9 pin connector LC201 LC202 amp LC206 You can buy the wiring harness from us and replace the connector with 8 pin plug or without 8 pin plug
18. sd 3 Capacitor Option Light black red orange Res motor 4 7 Connecting Additional Functions The Series 2 decoders have 4 6 additional functions Each function output can reach 300mA LocoCruiser standard series decoder user manual Ver1 0 9 JANE 4 8 Suitable Light Bulbs Each function output can directly connect with 12 v bulb unless the locomotive instructions say it cannot support the voltage of the blub 4 9 Suitable locomotive type The ANE MODEL LocoCruiser standard decoder is suitable for all HO scale and some N scale locomotives size permitting The decoder is fully compatible with NMRA DCC standards and can be controlled by various DCC digital command control systems which are compatible with DCC standards Operating by conventional DC controller is possible without any problems 5 Initial operation 5 1 DCC Mode Remove any capacitors that are wired into the track feeders This could impair the functionality of the decoder The LocoCruiser works with any DCC system Unfortunately the DCC protocol also bring some difficulties into the game One of them occurs so often that we deal with it right away 5 1 1 DCC Speed Steps flashing lights Lights do not work with DCC systems DCC locomotives run with 14 28 or 128 speed steps The decoder must know the speed step setting of the command station The command station must be able to operate with this mode and must be s
19. switch setting in particular in the following table so you can refer to each different needs to adjust CV29 Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Value Function Reverse 140r DC analog Bi direction Speed Long description direction of 28 128 operation control Not table address loco speed release steps LocoCruiser standard series decoder user manual Ver1 0 13 ANETE za eo eg ee 0 Open 1 S Open Ss e 2 Open Open SS e 3 SS Open e e 4 Open Es Open SS e 5 default SS Open Open 6 Open Open Open ge e 7 Open 16 Open z Open SS 17 Open Open S 18 Es Open es Open SS 20 8 Open Open Ss Open 22 Open Open Open 8 Open 23 Open 32 Open 5 7 Open 33 Open eg e Open 34 Open Open e Open 35 S Se Open Open 36 Open Open Open 37 Open Open Open 38 Open Open Open Open 39 8 eg Open Open 48 Open SS Open Open 49 Open e Open Open 50 Open Open Ss Open Open 51 Open Open Open 52 Open Open Open Open 53 Open Open Open Open 54 Open Open Open Open Open 55 6 Decoder Settings Programming 6 1 Configutation Variables CV Almost all configuration Variables CVs LocoCruiser decoders follow the CV concept developed in the US CV stands for Con
20. ted or broken because of improper management by user so that the product cannot work normally User does not follow the instructions in this manual to operate the product which causes damage or malfunction The right of the above declaration belongs to ANE Model 9 Troubleshooting Some reasons may cause the LocoCruiser standard series Decoder not to work as desired LocoCruiser standard series decoder user manual Ver1 0 i Here are some frequently asked questions and the answers that may help you use the product properly 9 1 The Decoder is installed After electrified the lights do not work and the locomotive does not move after changing speed Check if the wires are fitted properly Check if any short circuits between the DCC control and the track 9 2 During the locomotive moving the moving is not continuous Check if the track is clean Check if the wires are fitted properly and good connections 9 3 The locomotive runs normally but the lights do not work If the lights do not work check if the wires are fitted properly Repeatedly press the light button then see if something has changed Read the CV value that activates the lights and check if the lights are turned off Refer to Chapter 5 3 1 for more detail If the problem remains please ask our dealer for a new unit 9 4 Headlights work but the locomotive does not move Read the
21. the 14 step 28 step and 128 step control of the DCC protocol and 8 lighting effects including dimmer warning effect blinking by speed effect random blinking effect strobe light effect and 3 fixed frequency blinking effects ANE MODEL Standard decoder should be your first choice as they can offer you flexibility and reliability that you have come to expect to have a state of the art decoder Caution Please feel free to contact ANE MODEL or ANE MODEL Authorized Distributor with any questions or concerns you might have about our products We are always looking forward to hearing your voice and make our products better Don t hesitate to contact us 2 LocoCruiser Standard decoder Series 2 LC201 LC202 LC203 LocoCruiser standard Back EMF decoder with NMRA 8 pin plug LocoCruiser standard Back EMF decoder without NMRA 8 pin plug LocoCruiser standard Back EMF decoder with NMRA 21 pin plug The picture of Dm the product S i Working voltage 12V 26V 12V 26V 12V 26V 1 5 Amp continuous and 1 5 Amp continuous and 1 5 Amp continuous Motor current 2 Amp peak 2 Amp peak and 2 Amp peak Functi tput inn tis 16V 16V 16V voltage Function output Ce ee 300mA 300mA 300mA max current Workin 0 80 C 0 80 C 0 80 C temperature Dimension L W 1 26 mm 0 6 15 5 1 26 mm 0 6 15 5 1 26 mm 0 6 15 5 T mm 0 2 5 mm mm 0 2 5 mm mm 0 2 5 mm LocoCruise
22. ting voltage starting voltage 0 14 28 0 14 28 Figure 4 1 Speed curve with CV6 lt CV5 2 Figure 4 2 Speed curve with CV6 gt CV5 2 You can see the change from the figure 4 2 If CV6 gt CV5 2 When the speed value is less than the middle value 14 i e in a low speed status the speed change is fast When the speed value is higher than the middle value 14 i e in a high speed status the speed change is slow 256 maximum voltage 128 Starting voltage 0 0 14 28 Figure 4 3 Speed curve with CV6 CV5 2 You can see the change from the figure 4 3 If CV6 CV5 2 both the high and low speed change are slow It s the same result for the speed curve with CV6 0 or 1 5 2 2 Speed table mode The speed curve is divided into 28 steps in the speed table mode Each speed value responds the values from CV67 to CV94 as per figure 4 4 256 128 Figure 4 4 Speed table In the speed table mode to modify the CV of the co responding speed step means to modify the value of the speed step to achieve a different result LocoCruiser standard series decoder user manual Ver1 0 11 ANETE 5 2 3 Speed model Exchange Setting bit 4 of CV29 enables to switch the two modes The speed curve mode is activated if the value is 0 Ifthe value is 1 the speed table mode is activated default setting 5 2 4 Acceleration amp Deceleration The final acceleration of the locomotive is determined by the value of CV3 on the other hand th
23. tor 6 White Front light 7 Blue Function Common 8 Red Right Rail WM el Capacitor Option After finishing the installation please check the motor and function wiring is completly insulated If not the decoder could short out and burn out will not be covered by warranty Please be careful If this happens then the decoder LocoCruiser standard series decoder user manual Ver1 0 CG The wire color comparison table of 6 pin DCC standard interface No Color Connect 1 Orange Motor 2 Gray Motor 3 Red Right track 4 Black Left track 5 White Front light 6 Yellow Rear light Please make sure all connected wires are correct Connecting wrong wire could destroy the decoder 4 5 1 Wiring Diagram for LocoCruiser LC202 WM browr Light AUX2 a green yellow AUX1 Capacitor Option black ED 4 6 Locomotive with 21 pin DCC standard Interface According to the instructions in the locomotive manual remove the body shell and find the 21 pin plug First remove the plug from the socket and find the correct direction Usually there s a number or arrow marked pin 1 on the 8 pin head And then fit with 8 pin head you ll finish the installation 4 6 1 Wiring Diagram for LocoCruiser LC203 Rear lt Light 4 brown 9 l i z L E FE O AUX2 Je f i r D green ma 4 RUXI yellow Head E
24. ts of CV value to reach the perfect running performance and lighting control We ll publish the related information on our website please follow the description for adjusting If you find that your locomotive doesn t run smoothly after installing the ANE MODEL decoder please feel free to contact us at once We will process your question promptly to make sure that your locos run smooth and trouble free 4 Installation To install the decoder is not that difficult as you think Just follow the following simple steps carefully you can enjoy the procedure on the instant Each ANE MODEL decoder comes with an instruction sheet that shows you the specifics of the decoder 4 1Ten Steps for successful decoder installation Read the instructions FIRST and PLAN your installation Have the proper tools on hand Choose a locomotive that runs well on regular DCC or DC system Choose the appropriate decoder for the installation Test the decoder before installation Carefully remove the body of the loco Plug the pins into the socket in accordance with the marks of the decoder and the circuit board of the locomotive If there s no socket or only 6 pin socket on your loco please choose LC202 version decoder and follow the wiring diagram below 9 Test the installation DCC 10 Customize your decoder by programming selected CVs 4 1 1 Avoiding heat problems with decoder installations Most HO amp N scale model locomotvie motors and lamps
Download Pdf Manuals
Related Search