Marmitek SS11 user manual
Contents
1. last time keep the button pressed After 3 seconds the LED shows the set up UnitCode Now release the button CHANGE OF THE BATTERY Remove the rocker switch at the y front of the 5511 and replace the battery Use an identical 12V Alkaline battery type A23 Mind the polarity when replacing APPLICATIONS With the Marmitek X 10 5511 wireless switch you can activate pre programmed macros in the CM15Pro computer interface You can also use the 5511 as a central operation panel for your Marmitek installation 8 O MARMITEK FREQENTLY ASKED QUESTIONS What is the reason for modules to switch on off spontaneously It is possible that a Marmitek X 10 System is installed at one of your neighbours using the same HouseCode To solve this problem try to change the HouseCode of your system or have FD10 Phase Coupler Filter installed at your incoming mains My modules will not respond to my controller Make sure that the HouseCode on all Modules and Controllers are set to the same HouseCode A My modules will not react to my remote sensor When you use a remote or sensor you should have at least one Transceiver or Marmitek Security Console installed in your house These components will translate the radio signals to the Marmitek X 10 signal on the power line Only one Transceiver should be installed for all remotes and sensors set to the same House Code The other modules do not respond to signals of the SS2. Any use of the Content but without limitation distribution reproduction modification display or transmission without the prior written consent of Marmitek is strictly prohibited copyright and other proprietary notices shall be retained on all reproductions 12 MARMITEK 5511 13 14 www marmitek com
3. local authorities Correct disposal and recycling will help prevent potential negative consequences to the environment and human health For more detailed information about the disposal of your old equipment please contact your local authorities waste disposal service or the shop where you purchased the product 10 MARMITEK DECLARATION OF CONFORMITY Hereby Marmitek BV declares that this SS11 is in compliance with the essential requirements and other relevant provisions of the following Directives Directive 1999 5 EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity Directive 2004 108 ec of the european parliament and of the council of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility Directive 2002 95 EC of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment MARMITEK BV BOX 4257 5604 EG EINDHOVEN NETHERLANDS C 0681 5511 11 COPYRIGHTS Marmitek is a trademark of Pattitude B V LMM31 trademark of Marmitek B V All rights reserved Copyright and all other proprietary rights in the content including but not limited to model numbers software audio video text and photographs rests with Marmitek B V
4. 11 What can be the problem Check if the 5511 has been set up correctly The easiest way to do this is to give again the correct HouseCode to the top button Has the battery been placed correctly The 5511 uses a Transceiver module TM13 IRRF7243 or one of the Marmitek X 10 alarm stations Check if it works properly for instance to use another remote control Maybe the range of the 5511 is not sufficient for your purpose if so when using a TM13 place an extra TM13 in the neighbourhood of your 5511 Do you still have questions Please check out www marmitek com for more information 5511 9 TECHNICAL DATA Supply 1 x A23 12V Alkaline Battery supplied RF range Up to 30m free field up to 20m through walls and ceilings RF frequency 433 92 MHz RF power 10mW 10 Key codes On off dim bright Ambient temperature 10 C to 50 C operation 20 C to 70 C storage Dimensions 80 x 80 x 20 mm Environmental Information for Customers in the European Union European Directive 2002 96 EC requires that the equipment bearing this symbol on the product MEN and or its packaging must not be disposed of with unsorted municipal waste The symbol indicates that this product should be disposed of separately from regular household waste streams It is your responsibility to dispose of this and other electric and electronic equipment designated collection facilities appointed by the government or
5. SSTIE 20424 20111128 SS11E ALL RIGHTS RESERVED MARMITEK MARMITEK TABLE OF CONTENTS TABLE OF CONTENTS veninio tanisin ra eecaneiifanons sitaaa fe pinni 2 SAFETY WARNINGS 3 HOW DOES MARMITEK X 10 WORK 4 ADRESSES i nn A SIGNAL RANGE 5 INSTRUCTIONS FOR USE SS11 WIRELESS SWITCH 7 INTRODUCTION 5 7 7 7 8 8 8 9 2 5 CHANGE OF THE HOUSECODE CHANGE OF THE UNITCODE CHANGE OF THE APPLICATIONS csi 5 FREQENTLY ASKED QUESTIONS TECHNICAL DATA aa DECLARATION OF COPYRIGHTS sides 422205242222 2 SAFETY WARNINGS e prevent short circuits this product should only be used inside and only in dry spaces Do not expose the components to rain or moisture Do not use the product close to a bath swimming pool etc Do not expose the components of your systems to extremely high temperatures or bright light sources e In case of improper usage or if you have altered and repaired the product yourself all guarantees expire Marmitek does not accept responsibility in the case of improper usage of the product or when the product is used for purposes other than specified Marmitek does not accept responsibility for additional damage ot
6. d to install a Phase Coupler Filter when your wall outlets and light switches are divided over more than one phase more than one group is no problem For bigger buildings or longer distances we advice you to use an active repeater instead of passive FD10 s 2 It is possible that Marmitek X 10 signals are attenuated by devices and lights which are connected to the power line In a normal home situation this effect is negligible the Marmitek X 10 system is using active gain control to eliminate the effects However it is possible that a particular device in your house is attenuating the signals so much that the range of Marmitek X 10 signals is decreased significantly When you have range problems it is wise to try to locate the device which is attenuating the signals simply by unplugging devices from the power line and testing the differences in range for your Marmitek system When e g your conclusion is that e g your computer monitor is attenuating the signal you can use a FM10 5511 5 Plug in Filter between the power line and the monitor to eliminate the effects Known devices which can cause attenuation are PC Monitors PCs with heavy internal power supplies Old Televisions Copiers Fluorescent Lights Gas Discharge Lamps Energy Saving Lamps 3 Some old devices are able to disturb the signal by transmitting noise on the power line Because the Marmitek X 10 signals are transmitted on 120 kHz only noise on or near thi
7. her than covered by the legal product responsibility e This product is not a toy Keep out of reach of children Do not open the product battery panel excepted the device may contain live parts The product should only be repaired or serviced by a qualified expert Keep batteries out of the reach of children Dispose of batteries as chemical waste Never use old and new batteries or different types of batteries together Remove the batteries when you are not using the system for a longer period of time Check the polarity of the batteries when inserting them in the product Wrong positioning can cause an explosion e Automatic switching devices provide comfort but can also be dangerous They can surprise people or can ignite clothing hanging over an electric heat source Please be careful and take appropriate measures to avoid accidents 5511 3 HOW MARMITEK 10 WORK Marmitek X 10 components use the existing mains wiring to communicate using Marmitek X 10 signals You can build a complete system using the three different kind of components of the Marmitek X 10 System 1 Modules These components will receive Marmitek X 10 signals and will switch or dim the attached lamp or appliance Examples of these modules are lamp modules and appliance modules These are available as build in micro DIN rail and plug in modules 2 Controllers These components will transmit Marmitek X 10 signals and thus will co
8. ntrol the Modules 3 Transmitters Wireless components like remotes The signals of these components will be received by a controller with transceiver functionality IRRF 7243 TM13 CM15Pro The Transceiver will translate the signals into Marmitek X 10 signals on the power line ADRESSES Up to a maximum of 256 different addresses can be preset These are subdivided into a so called HouseCode A to P incl and a UnitCode 1 to 16 incl The HouseCode can also be set on the controllers so that the controllers and modules become part of the same system The address can be set either using code dials or by pressing buttons depending on the type of module The Marmitek X 10 System uses standard commands which control all units with the same HouseCode at the same time e g all lights on all units off etc 4 MARMITEK SIGNAL RANGE Range of Marmitek X 10 signals over the Power Line and how to increase the range The Marmitek X 10 System is based on power line communication The range of the Marmitek X 10 signals very much depends on the local circumstances On average the range is a cable length of 80 meters If you have difficulties with the range of your Marmitek X 10 signals please pay attention to the following facts 1 When more than one phase is used for your electrical system it is necessary to couple these phases for the Marmitek X 10 signals For coupling you can use FD10 Phase Couplers Filters You only nee
9. on walls glass doors tables etc and transmits high frequent signals through walls and ceilings The SS11 wireless switch transmits radio graphical signals to an X 10 Transceiver TM13 IRRF7243 or Marmitek X 10 Alarm station Then the Transceiver or Station transmits these signals via the in your house already installed electric wiring Through this you can switch on and off your lighting or apparatus connected to X 10 receivers lighting can be dimmed also The 5511 is completely wireless and battery powered PROPERTIES The switches are delivered standard at HouseCode A CHANGE OF THE HOUSECODE 1 Press the button ON and keep it pressed The red LED flashes shortly After 15 seconds the present set up is shown 1 flash is HouseCode A 2 flashes is HouseCode B etc 2 Release the button ON 3 Now press shortly for the desired HouseCode on the same ON button 1 A 2x etc The LED flashes every time you press the button 4 last time keep the button pressed After 3 seconds the LED shows the set up HouseCode Now release the button 5511 7 CHANGE OF THE UNITCODE 1 Press the OFF button and keep it pressed The red LED flashes shortly After 15 seconds the present set up is shown 1 flash is UnitCode 1 2 flashes is UnitCode 2 etc 2 Release the OFF button 3 Now press shortly for the desired UnitCode on the same OFF button 1x 1 2x 2 etc The Led flashes every time you press the button 4
10. s frequency will have influence on the range When you use a FM10 Filter to connect this device to the power line the noise will be filtered 4 The Marmitek X 10 protocol has several mechanism to avoid modules to be switched on or off by other sources than your Marmitek X 10 Controllers However it is possible that the Marmitek X 10 signals are disturbed by e g baby phones which are in TALK mode continuous transmission When these kind of signals are present on the power line it is possible that the Marmitek X 10 signals will not come through 5 The mains do not stop at the front door of your home Everything that is attached to mains nearby your home can have influence on Marmitek X 10 signals e g heavy machinery If you think that your system is influenced by devices out of your house it is advisable to install FD10 Phase Coupler Filter on each phase entering the house These filters will block signals coming into or going out of your house but will also match the impedance for the mains Hereby make your house Marmitek X 10 compatible for these units The FD10 s will not only filter but will also couple the phases please see 1 6 MARMITEK INSTRUCTIONS FOR USE SS11 WIRELESS SWITCH INTRODUCTION Congratulations buying the Marmitek X 10 5511 wireless switch This is a super thin elegant wireless switch It is the ideal solution for situations where an extra switch is needed without installing wires It is to install
Download Pdf Manuals
Related Search