5 Bay SAS/SATA II HDD JBOD USER'S MANUAL
Contents
1. CHAPTER 1 INTRODUCTION 1 1 Key features v v miniSAS wide port supports 1200MB s high speed transmission miniSAS wide port supports JBOD expansion Supports hot swappable 3 5 SAS and or SATA II drives Supports SES2 SCSI Enclosure Services 2 and SAF TE SCSI Accessed Fault Tolerant Enclosures for In Band Enclosure management Intelligent firmware design without complicated setting RS232 Support Console for firmware update and status check Audible alarm and LEDs indicators for FAN failure or Over temperature 1 2 Checking list Before removing the subsystem from the shipping carton visually inspect the physical condition of the shipping carton Exterior damage to the shipping carton may indicate that the contents of the carton are damaged If any damage is found do not remove the components contact to the dealer where the subsystem was purchased for further instructions Before continuing first unpack the subsystem and verify that the contents of the shipping carton are all there and in good condition The package contains the following items One set JBOD with 5 units HDD tray Shipping without drives installed 3 5 HDD tray screw bag x1 20 pieces flathead screw are included Power cord x1 type based on different territories Installation CD Rom x1 User Manual x1 Note Inspect the shipping cartons for evidence of physical damage If a shipping carton appears damaged request that the ca2. HDD to the tray by using four mounting screws shown as below HDD Drive Rear view of HDD tray il screw 6 Repeat step 1 to 5 for all remaining HDD trays 2 2 How to replace the fan 1 Lay down the 5 bay tower on the flat surface right side on the top 2 Release the 2 thumbscrews by following the direction shown as below 3 Push the cover in the direction shown as below photo 5 Unscrew the four screws and remove the fan guard at rear side 6 Take out the fan from the enclosure and install a new one 7 Fasten the four screws and fan guard again 8 Plug the fan cable in the slot 2 3 Powering on the device After HDD installation is complete the device can be turned on Please check the following items 1 Ensure that the cables are connected 2 Plug in corresponding power cord to AC main set 3 Press the ON OFF switch on the front panel then the system will boot CHAPTER 3 FIRMWARE UPGRADES 3 1 In band Firmware Upgrade 1 Boot up the PC after the SAS HBA Adapter is installed 2 Windows will detect new device Found New Hardware Installing 3 Run the file fwloadfuf exe it will detect SAS device automatically e FwlaadFuf 4 When the application detects the SAS device the Firmware Loader window will display Vitesse Firmware Loader Select Firmware Image Select Device S TOD Expander Update 5 Click Browse to select the firmware f
3. 39 Throughput 515 cps Bae SUD File ni Elapsed 00 00 42 gt fwburn uart Firmware Update via Serial Port Start XMODEM 128 transfer of fuf firmware file W control M 3 or more times to abort transfer eee will go to UART RMON but may not be visible Connected 0 35 40 T100 9600 8 N 1 SCROLL CAPS INUM j start 3 e 28 Computer Management Adaptec Storage Man Q 9600 HyperTermi C 192 168 1 35 datal W Fwupdate3 JPG Paint QJ 5 02 PM 6 SAS JOB will restart automatically when firmware upgrade is completed 7 Enter Hyper Terminal again to ensure that the latest version firmware has been updated by checking the Firmware Version le x File Edit wiew Call Transfer Help 05 295 gt P 25 stat GNU Build C Firmware Version 304b Status Status OK CRC NONE Versions Module Vers Description Date Time AIC 50 100 Expander SPI libvos 95 0 libsyssu 05 04 System Services Library Jul 8 2007 22 48 06 libdey 03 03 GIWS Device Library Jul 8 2007 22 47 58 sspSes 03 04 SSP SES Diagnostic Library Jul 8 2007 22 49 00 libSMP 03 04 SMP Transport Library Jul 8 2007 22 48 37 libSSP 03 04 SSP Transport Library Jul 8 2007 22 48 44 libPHV 03 04 PHY Transport Library Jul 8 2007 22 48 55 libGUI 93 04 GUI Transport Library Jul 8 2007 22 48 56 Transport Configuration Name Base Int Diag libSHP ONBOARD i libSSP ONBOARD i libP
4. 5 Bay SAS SATA Il HDD JBOD XJ SA12 005 USER S MANUAL Document number MAN 00079 C P N H88TJ53660 AP010 0 Important Information Warranty Our product is warranted against defects in materials and workmanship for a period of one year from the date of shipment as evidenced by receipts or other documentation The manufacture at its option repair or replace equipment that proves to be defective during the warranty period This warranty includes parts and labor The media on which you receive software are warranted not to fail to execute programming instructions due to defects in materials and workmanship for a period of 90 days from date of shipment as evidenced by receipts or other documentation The manufacture will at its option repair or replace software media that do not execute programming instructions if the manufacture receives notice of such defects during the warranty period The manufacture does not warrant that the operation of the software shall be uninterrupted or error free National Instruments believes that the information in this document is accurate The document has been carefully reviewed for technical accuracy In the event that technical or typographical errors exist the manufacture reserves the right to make changes to subsequent editions of this document without prior notice to holders of this edition The reader should consult National Instruments if errors are suspected In no event shall the manufacture be li
5. HV ONBOARD i libGUI ONBOARD i sspSes Build Version Stamp depot uvscFwKit Releases SRS Rev03 04 328 Release Build Connected 1 13 13 Auto detect 9600 8 N 1 CAPS Capture Print echo 989600 HyperTerminal d Adaptec Storage Manager public on 192 168 1 10 Sir untitled Paint ey oS 2 23PM 11
6. N 1 SCROLL CAPS Capture Print echo start 3 8 m Computer Management Ei Adaptec Storage Man 9600 HyperTermi y fwupdate2 JPG Paint L3 My Documents D 9 b 5 11 PM 4 Click Browse and select the firmware file to upgrade fuf file then press Send X control M 3 or timas to ahort trancfor Messages will go to UARTO CCCCCCCCCCBB BBOBBOBBO ERR Never got SOH from other NET Aborted by user or transport Firmware update failed gt fwburn uart Firmware Update via Serial Port Start 128 of fuf firmware file X control M 3 or more times to abort transfer Messages will go to UARTO RMON but may not be visible CCCCCCCCCCBBOBBOBBOBBO ERR Never got SOH from other side Aborted Aborted by user or transport Firmware update failed Documents i Deskto p 6 hy Documents OL Mu Computer Ed Mu M Fili 1a E5 A C 5 1 p A 3 O44 fuf j Places 10 5 The Xmodem file send for 9600 window will show the firmware upgrade status zig x File Edit View Call Transfer Help Dl 5 5E xmodem file send for 9600 Sending C Documents and Settings Administrator Desktop EJ55 AIC 5_10D A0 3 Packet ha Error checking c Retries Total retries Mo Last error Gotrety request ss lt CS 22K of 313K Remaining 00 09
7. able for any damages arising out of or related to this document or the information contained in it EXCEPT AS SPECIFIED HEREIN THE MANUFACTURER MAKES NO WARRANTIES EXPRESS IMPLIED OR STATUTORY AND DISCLAIMS ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE OR NON INFRINGEMENT OR A WARRANTY THAT THE PRODUCT WILL OPERATE ERROR FREE IN NO EVENT SHALL THE MANUFACTURER BE LIABLE FOR THE COST OF PROCUREMENT OF SUBSTITUTE HARDWARE SOFTWARE OR SERVICES LOST PROFITS LOST DATA OR ANY SPECIAL INDIRECT CONSEQUENTIAL OR INCIDENTAL DAMAGES HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY ARISING IN ANY WAY OUT OF THIS AGREEMENT OR THE SERVER THIS LIMITATION SHALL APPLY EVEN IF THE MANUFACTURER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES AND NOTWITHSTANDING ANY FAILURE OF ESSENTIAL PURPOSE OF ANY LIMITED REMEDY PROVIDED HEREIN This limitation of the liability of the manufacturer will apply regardless of the form of action whether in contract or tort including negligence Any action against the manufacturer must be brought within one year after the cause of action accrues The manufacture shall not be liable for any delay in performance due to causes beyond its reasonable control The warranty provided herein does not cover damages defects malfunctions or service failures caused by owner s failure to follow the manufacture installation operation or maintenance instructions owner s modificati
8. ance If one of the following situations arise the equipment should be checked by service personnel v power cord or plug is damaged Y Liquid has penetrated the equipment v The equipment has been exposed to moisture 4 The equipment does work well or will not work according its user manual v equipment has been dropped and or damaged lt The equipment has obvious signs of breakage v Please disconnect this equipment from the AC outlet before cleaning Do not use liquid or detergent for cleaning The use of a moisture sheet or cloth is recommended for cleaning Note Product features and specifications are subject to change without notice Table of Contents CHAPTER T INTRODUCTION tat ap Geld can a Gales 1 Tod S ey eee errr Re NR M ba IN cM Ita M M GUN 1 LZ Chee IU 1 resi E OS E 2 1 4 Hear PallelFealufeS 3 CHAPTER 2 INSTALLATION 4 2 1 How to install and remove HDD Trays 4 2 2 TOW to 5 2 deV CE 6 CHAPTER 3 FIRMWARE UF GRADES tetas 7 3 1 In band Firmware 7 3 2 Out of band Firmware 8 vi
9. er pmDevicefrrayControl Solt Hum 00000003 Normal Status pmDeuiceflrrayControl Solt Hum 00000004 Normal Status pmDeviceflrrayControl Solt Hum 00000005 Normal Status gt gt gt fwburn uart Firmware Update via Serial Port Start KMODEM 128 transfer of fuf firmware file X control M 3 or more times to abort transfer Messages will go UART RMON but may not be visible Sends a file to the remote system start E 8 ml Computer Management Si Adaptec Storage Man 9600 HyperTermi Y fwupdate4 JPG Paint Ca My Documents D 5 11 PM 3 At Send File window select Xmodem in Protecol column 9600 HyperTerminal File Edit View Call Transfer Dag Ss EE Solt Hum 00000002 Normal Status pmDeviceArrayControl Solt Hum 00000003 Normal Status pmDeviceflrrayControl LITTLE 204 Solt Hum 00000004 Folder C Documents and Filename Normal Status Browse Protocol pmDeuiceflrrayControl modem b Solt Hum 00000005 Cancel Normal Status gt gt gt gt gt fwburn uart Firmware Update via Serial Port Start KMODEM 128 transfer of fuf firmware file Type M 1 3 or more times to abort transfer Messages will go to UART RMON but may not be visible CCCCCCCCCC Connected 0 44 54 ivT100 9600 8
10. on computer boards are sensitive to static electricity Before handling a board or integrated circuit touch an unpainted portion of the system unit chassis for a few seconds This will help to discharge any static electricity on your body Place this equipment on a reliable surface when install A drop or fall could cause injury Please keep this equipment away from humidity Do not leave this equipment in an environment unconditioned out of operation or storage temperature range may damage the equipment Never pour any liquid into ventilation openings this could cause fire or electrical shock Make sure the voltage of the power source is within the specification on the label when connecting the equipment to the power outlet The current load and output power of loads shall be within the specification This equipment must be connected to reliable grounding before using Place the power cord out of the way of foot traffic Do not place anything over the power cord The power cord must be rated for the product voltage and current marked on the product s electrical rating label The voltage and current rating of power cord should be greater than the voltage and current rating marked on the product If the equipment is not used for a long time disconnect the equipment from mains to avoid being damaged by transient over voltage Never open the equipment For safety concerns only qualified service personnel should open the equipment for mainten
11. on of the product owner s abuse misuse or negligent acts and power failure or surges fire flood accident actions of third parties or other events outside reasonable control Copyright Under the copyright laws this publication may not be reproduced or transmitted in any form electronic or mechanical including photocopying recording storing in an information retrieval system or translating in whole or in part without the prior written consent of the manufacture Trademarks Product and company names mentioned herein are trademarks or trade names of their respective companies Changes The Manufacturer reserves the right to revise this publication and to make changes in the content hereof without the obligation of the manufacturer to notify any person of such revision or changes iii SAFETY PRECAUTIONS Before getting started please read the following important cautions All cautions and warnings on the equipment or in the manuals should be noted Most electronic components are sensitive to electrical static discharge Therefore be sure to ground yourself at all times when installing the internal components Use a grounding wrist strap and place all electronic components in static shielded devices Grounding wrist straps can be purchased in many electronic supply stores Do not open the top cover of the system If opening the cover for maintenance is a must only a trained technician should do so Integrated circuits
12. rrier s agent be present when the carton is opened Keep all contents and packing materials for the agent s inspection 1 3 Front Panel Features LED indi r Fan fail LED On when system detects fan abnormality Over Temp On when system temperature exceeds the LUE e Power On When system is ME on HDD Activity On when HDD is connected Flash when accessing HDD Off when system does not detect the HDD HDD Fail Normally this LED is controlled by Host RAID card or HBA It is ON to indicate HDD failure Rebuild or Locating but varies from different HBAs 1 4 Rear Panel Features Q Host miniSAS 4x connector for HBA or RAID adapter O Expansion miniSAS 4x connector for JBOD expansion Connect to host COM port RS 232 Phone Jack Console can be used for firmware upgrade and detail status monitor if necessary 1 Reserve 2 Buzzer Enable OFF Disable ON Enable default Heart Beat LED Heart Beat indicator Q Power AC inlet Connect a power cord to the AC inlet for power supply O Factory reserved switch CHAPTER 2 INSTALLATION OVERVIEW Warning Before removing or install the unit be sure that the unit is not turned on or connected to the AC power 2 1 How to install and remove HDD Trays 1 Press the latch to the right side by the thumb 2 Push the tray door outward by the forefinger at the same time 3 Pull the HDD tray from the bay genily 4 Secure the
13. uf file then press Update to start firmware upgrading Vitesse Firmware Loader Select Firmware Image cb ocuments and Settings sdministratarsDiesk top E Select Device Product Id S100 Expander 6 The firmware upgrade will be completed in 2 minutes then the firmware Loader window will display again 7 SAS JBOD will restart automatically 8 To restart the host PC to continue further operation 3 2 Out of band Firmware Upgrade 1 At HyperTerminal type fwburn uartO and press Enter File Edit wiew Call Transfer Help Dag 5s pmDeuiceflrrayControl Solt Hum 00000002 Normal Status pmDevicefrrayControl Solt Hum 00000003 Normal Status pmDeviceflrrayControl Solt Hum 00000004 Normal Status pmDeuiceflrrayControl Solt Hum 00000005 Normal Status gt fw fwburn fwcfg fwcheck fwerase fwgetreg fwrollback gt gt gt gt gt gt fwburn uart Connected 0 29 55 100 9600 8 N 1 SCROLL CAPS Capture Prin it echo start Ge Computer Management d Adaptec Storage Manager 9600 HyperTerminal 2 11192 168 1 35ldatal5 B Bm 4 57PM 2 Select Transfer and click Send File 9600 HyperTerminal File Edit view Call Transfer O m 239 5 Hl Send File Receive File Capture Text Send Text File Solt Hum Normal Sta Capture to Print
Download Pdf Manuals
Related Search