User Manual - Hope Industrial Systems
Contents
1. NEMA 2 CABLE HOOD NEMA 4 CONDUIT ACCESS PANEL NEMA 12 CABLE GLAND KEYBOARD TRAY NEMA 2 REAR PANEL OPTIONAL NEMA 4 12 wio LOUVERS DOES NOT APPLY TO CONDUIT CONNECTION ON NEMA 4 17 Specifications Display Type Thin film transistor TFT Active Matrix Liguid Crystal Size 17 diagonal Image size 13 3 338mm x 10 6 270mm Native resolution SXGA 1280 x 1024 Plug and Play DDC1 2B compatible Minimum resolution 640 x 480 Pixel pitch 0 264mm x 0 264mm Number of colors 16 million Viewing Angle Hori Vert 160 160 typical Brightness white 300 nits cd m max Contrast ratio Back light 600 1 typical Four CCFTs Cold Cathode Fluorescent Tube 50 000 hours brightness half life replaceable Screen protector when not shipped with touch screen Tempered glass to ANSI Z97 1 SPEC AR coated on both sides 98 Transmission of light 99 Reduction of glare 5396 UV blocking 3096 NIR Blocking proprietary hydro phobic coating on outside reduces fingerprint smears repels liquid spills and makes glass easy to clean Video Input connector HD 15 optional BNC input Input signal format RGB Analog video 0 0 7V p p sep V and H combined Sync sync on green Horizontal scan 30kHz 81kHz Supported Video Stan Std VGA 640x480 60Hz dards SVGA 800x600 60Hz XGA 1024x768 60Hz SXGA2. will not ex ceed the rated specifications of the unit gt The maximum rated temperature of the HIS WL17 is 45 C 113 F gt Also remember that even though this product is designed to operate at 45 the life span of any electronic device is shortened when it is consistently operated at high temperatures Therefore it is wise to take steps to keep the temperature of the ambient air around the unit as low as possible 4 Ensure that the ambient humidity of the air around the unit does not exceed the rated specifications for the unit gt The maximum rated humidity for the HIS WL17 is 9090 non condensing Installation using VESA mounting units come standard with a 100mm square VESA mounting pattern with M4 threads 75mm VESA pattern is also available on the NEMA 12 version If this mounting method is used consider the following Y screws should not protrude into the rear cover by more than 1 4 Y The capacity of the arm or mounting plate selected should take into account the total weight of the monitor and its center of gravity Y For NEMA 4 4X applications the mounting interface should be properly sealed to prevent egress of water 10 Installation using Bench Top mounting option SPACER NYLON BUSHING RUBBER WASHER n di n KNOB YOKE LOCKING NUT TIGHTEN AND INSTALL LOCKING SCREW YOKE THIS SIDE FORWARD 3 DIA WASHER POLYETHYLENE FRICTION PLATE BENCH MOUNTING PLATE 38 y
3. Electric Code and authorities having jurisdiction FCC Notice This eguipment has been tested and found to comply with the limits for a Class A digital device pur suant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the eguipment is operated in a commercial environment This eguipment generates uses and can radiate radio freguency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this eguipment in a residential area 15 likely to cause harmful interference in which case the user will be re guired to correct the interference at his own expense Any changes or modifications not expressly ap proved by the grantee of this device could void the user s authority to operate the device Factory Preset Timing Horizontal Vertical i Sync Freguency Freguen Polari Resolution ty H V Lo J c VESA 800 x 600 vasre 75025 13500 sie Factory recommended timings for best picture quality Control Panel Buttons and Indicators Control Panel Button Description Opens the OSD menu Also used to exit the OSD Always menu or return to the previous menu MagicBright Provides an optimum viewing environment depend ing on the contents of the image you are watching Currently four different modes are available Each mode has its own
4. Make sure all cables are connected If the LED turns orange check to see if the PC is in the power saving mode by pressing any keys on the keyboard Change PC display resolution to 1280x1024 at 60 Hz refresh Unplug the power adapter to monitor and then plug it in again Press monitor power button again Reset the monitor to the original factory setting Press Auto button Press the Auto button Make sure the PC display resolution is not set greater than 1280 1024 75hz Make sure the PC display resolution matches one of the factory preset timings in this manual Change the PC display resolution to 1024x768 at 60hz Reset the monitor to the factory setting Press the Auto button Make sure the PC display resolution matches one the factory pre set timings shown in this manual Recall factory setting Refer to panel controls and OSD functions in this manual Fine tune the picture by performing the following adjustments in this order pitch phase and position Refer to OSD functions in this manual To unlock press the MENU and AUTO buttons simultaneously for atleast 5 seconds see page 7 Drawings Front View 16 40 416 6 DISPLAY AREA Bottom Side and Rear View of NEMA 12 option VESA MOUNTING cnn 75mm X 75mm NEMA 100mm X 100mm all m SIDE MOUNT 1 4 20 INTERNAL THREAD X 625 DEEP OOO 909 CABLE ENTRY 3 MODELS
5. PLATE SEALING WASHER SEALING PLATE RUBBER WASHER LOCK NUT YOKE LOCKING NUT INSTALL 6 32 ANTI ROTATION SCREW 3 DIA WASHER POLYETHYLENE FRICTION PLATE YOKE THIS SIDE FORWARD PEDESTAL TOP PLATE IN STALL WITH FOUR 1 4 20 FLAT HEAD STAINLESS STEEL SCREWS 42 HIGH PEDESTAL 2 50 63 5 IN BOTTOM OF PEDESTAL FOR HIDDEN 41 CABLE ACCESS Note The 34 conduit and other sealing hardware are not reguired for NEMA 12 monitors or NEMA 4 4X monitors with the 4 cable gland 13 14 Free pedestal top plate from assembly by removing retaining screw yoke locking nut stainless steel washer and 4 14 20 screws Position and support the monitor and yoke assembly so that cables exiting from the monitor can be easily routed into the top of the pedestal Install the pedestal top plate and polyethylene friction plate using the four 14 20 screws insuring all cabling inside the pedestal has been fed through the top of the pedestal top plate Connect all communication and power cables to the monitor insuring all remaining hardware has been threaded onto the cables in their proper order per the illustration above Connectors that do not have a locking mechan ism should be sheathed in heat shrink tubing to insure that they do not come loose inside the pedestal Install the monitor and yoke assembly onto the top of the pedestal with the stainless steel washer the yoke locking nut and the ret
6. pre configured brightness value You can easily select one of four settings by simply pressing MagicBright control buttons 1 Text Normal Brightness For documentation or work involving heavy text When the OSD Menu is Internet Medium Brightness NOT Dis For working with a mixture of images such as text and graphics Entertain High Brightness For watching motion pictures such as a DVD or VCD Custom Although the values are carefully chosen by our engineers the pre configured values may not be comfortable to your eyes depending on your taste Ifthis is the case adjust the Brightness and Contrast using the OSD menu When the Adjusts items in the menu DOWN OSD Menu is Being Dis played Control Panel Button Description When the Push to adjust brightness OSD Menu is NOT Dis played When the Adjusts items in the menu UP OSD Menu is Being Dis played ENTER When Activate a highlighted menu item OSD Menu is Being Dis played AUTO Use this button for auto adjustment of the display POWER mE Use this button to turn the monitor on and off This light glows green during normal operation and POWER blinks green once as the monitor saves your adjust INDICATOR ments Direct Functions Menu Description When the AUTO button is pressed the Auto Adjustment screen ap pears as shown in the animated screen on the center Auto adjustment allows the monitor to self adjust to the incoming video
7. signal The values of fine coarse and position are adjusted automati cally To make the automatic adjustment function sharper execute the AUTO function while the AUTO AUTO PATTERN is on IMPORTANT NOTE LOCKING CONTROL PANEL BUTTONS The control panel buttons can be locked by simultaneously pressing the AUTO and MENU buttons for 5 seconds Repeating this operation will unlock the buttons Menu Description Push the MagicBright repeatedly to circle through four available pre MagicBright onfigured modes Brightness Adjust brightness OSD Functions Important Note Except for Brightness and Contrast all of these func tions are automatically set by using the AUTO Button Menu Description Brightness Direct Access Feature When OSD is not on the screen push the button to adjust brightness Contrast Adjust the contrast Color Menu Description Color Tone The tone of the color can be changed and one of four modes can be selected Cool Normal Warm and Custom Color Control Follow these steps to adjust individual R G B color balance Gamma Select one of three pre defined gammas Image Menu Description Removes noise such as vertical stripes Coarse adjustment may move Coarse the screen image area You may relocate it the center using the Horizon tal Control menu Fi Removes noise such as horizontal stripes If the noise persists even
8. 1280x1024 9 60Hz native Vertical scan 56Hz 75Hz Response rate typical 12ms 18 Electrical Monitor input Power consumption 90VAC 264VAC 50 60Hz 3Hz Less than 34W Power management Compliance DPMS energy star lt 1W UL 1950 cUL 959 FCC Class A Environmental Temperature 0 45 C Humidity 20 to 90 non condensing Shock 30g 1 2 sine 11 msec Vibration 0 006 inch p p 15 57Hz 1 09 57 640Hz sine Altitude Operating up to 10 000 feet Non operating up to 40 000 feet Functional Panel controls rear access Menu MagicBright Brightness Adjust Enter Auto Power Power Indicator OSD On Screen Display controls Brightness contrast color tone color control gamma coarse fine sharpness H position V position OSD lan guage OSD H position OSD V position OSD transparency OSD display time image reset color reset information Touch screen option 5 wire resistive system emulates a mouse Serial RS 232 or USB interface to host computer 19 Enclosure Type Self contained NEMA 12 black powder coated steel Panel rating NEMA 12 Physical Dimensions Height Width 16 4 417mm W x 13 94 354mm H Depth 3 25 83mm Net weight Black Carbon Steel Model 15 50 Ibs Stainless Steel Model 17 90 Ibs Shipping weight Black Carbon Steel Model 18 lbs P
9. Hope Industrial Systems Inc TM User Manual 17 Universal Mount Industrial Monitor Model No HIS UM17 TABLE OF CONTENTS Safety and Regulatory 3 Factory Preset Timing toese mamma 4 Monitor Adjustment Functions Direct FUNCOMS iaie 5 OSD Functions 9122215222225 0 2421212829444 12121289 04 9 1242 8 Installation Instructions 10 Cleaning ait d 15 16 17 SDOCIICAIOFIS a 18 Warranty nennt 21 Safety and Regulatory Information Warning To prevent fire or shock hazard do not expose the unit to rain or moisture Dan gerously high voltages are present inside the unit Do not disassemble the unit Refer servicing to gualified personnel only This eguipment is not intended for use in critical applications where its failure to operate would create immediate life threatening circumstances Applications in cluding but not limited to nuclear reactor control aerospace navigation systems and life support systems are not appropriate for this product This product is a UL Listed Component and must be used with a listed computer A readily accessible disconnect device shall be incorporated in the building instal lation wiring Installation shall be in accordance with the National
10. IMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR THE LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU You are cautioned that the performance of this product can be affected by many factors such as system configuration software appli cation and operator control of the system It is your responsibility to determine suitability of this product for your purpose and application 21 Hope Industrial Systems Inc 1325 Northmeadow Parkway Suite 100 Roswell GA 30076 www HISmonitors com Publication UM WL17 Rev A March 2006 2006 Hope Industrial Systems Inc 22
11. af ine nA ter fine tuning repeat it after adjusting the frequency clock speed Sharpness Sets the clearness of the image H Position Changes the horizontal position of the display V Position Changes the vertical position of the display On Screen Display 050 Menu Description Language Changes the language used in the Menu H Position Changes the horizontal position of the OSD V Position Changes the vertical position of the OSD Transparency Changes the translucency of the background of the OSD The menu will automatically turn off if no adjustments are made for a cer Display Time tain time period You can setthe amount of time the menu will wait before it turns off Setup Menu Description Image Reset Image parameters are replaced with the factory default values Color Reset Color parameters are replaced with the factory default values Information Menu Description Information Shows the video source and display mode Color Reset Color parameters are replaced with the factory default values Installation Instructions Preparing for Installation Important Perform the following steps BEFORE Installation of the monitor 1 Ensure that sufficient power is available 2 Ensure that sufficient space 15 available to allow for proper airflow around enclosure 3 Ensure that the air temperature around the unit top and bottom
12. aining screw Insure that there is a sealing washer underneath the retaining screw Feed all connectors and excess cabling inside the top of the pedestal Screw conduit elbow onto top of pedestal taking care to position the direc tion of the conduit to allow free tilting of the monitor without interference Cleaning Resistive Touchscreen model Any standard glass cleaner can be used to clean touchscreen AI ways spray the glass cleaner on the cloth or towel and then clean the touchscreen Glass cleaner sprayed directly on the monitor could possi bly leak inside a non sealed unit and cause damage Vinegar or ammonia will not hurt the touchscreen Again spray the cloth and then clean the touchscreen Tempered Anti Reflective Glass Window Use any standard glass cleaner as long as there is no abrasive or oily content The anti reflective coatings are physically part of the surface of the glass and resist degradation to the Military Specifications 15 Troubleshooting Note For troubleshooting with a KVM extender installed please refer to the Instal ler User Guide that comes with that eguipment Blank Screen After installing the power adapter and connecting I O cable to a PC the monitor displays a blank screen Rolling Screen Unstable Screen Screen is not perfect Auto Adjustment Locked 16 Press the power button and check to see if the power LED is lit If the LED turns green make sure the PC is powered on
13. in assignment Stainless Steel Model 21 Ibs Pin No Signal Pin No Signal 1 Red 9 No pin 2 Green 10 Ground 3 Blue 11 Ground 4 Ground 12 SDA 5 Ground 13 sync 6 Ground 14 V sync 7 Ground 15 SCL 8 Ground 20 Warranty Statement Who is Covered This warranty covers the purchaser of this product only and is not transferable without our written consent What Does This Warranty Cover and What is the Period of Coverage We warrant this product to be free from defects in material and workmanship subject to the conditions set forth below This warranty remains in force for a three year period beginning on the date we invoice you for the product If HIS repairs or replaces a product under warranty its warranty term is not extended What Will We Do to Correct Problems and How Do You Get Service We will repair or replace at our sole option any part of the unit which proves to be defective Replacement parts may be new or refurbished and will meet the same specifications of the original parts or unit We will return the product to you by the shipping method we choose in the U S A at our expense You must pay for shipments to locations outside of the U S A In order to receive warranty service you must get prior approval from HIS To request warranty service you can telephone us at 770 992 0297 or send an email to service OHISmonitors com If we determine that warranty service is
14. needed we will give you a Return Material Authorization RMA number This RMA number must be conspicuously marked on the outside of the shipping box HIS will not accept ship ments not accompanied by the RMA number You must ship or deliver the product to HIS Freight prepaid Pixel Faults Permanently dark or bright pixels can happen to TFT displays Five or less permanently dead pixels out of 1 3 million do not make a good case for exchanging the unit Please contact our Customer Service Department if the number of pixel faults exceeds the above mentioned figure What Does This Warranty Not Cover This warranty does not cover equipment which has been damaged due to misuse abuse or accident such as operat ing the equipment outside of published specifications displaying fixed images for long periods of time resulting in afterimage effects improper or unauthorized repair by anyone other than HIS or a service agency authorized by HIS to perform such repairs fire flood acts of God or other contingencies beyond the control of HIS HIS RESPONSIBILITY FOR MALFUNCTIONS AND DEFECTS IN HARDWARE IS LIMITED TO REPAIR AND REPLACEMENT AS SET FORTH IN THIS WARRANTY STATEMENT HIS SHALL NOT BE LIABLE FOR DIRECT INDIRECT INCIDENTAL CONSEQUENTIAL OR OTHER TYPES OF DAMAGES RESULTING FROM THE USE OF ANY HIS PRODUCT OTHER THAN THE LIABILITY STATED ABOVE THESE WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT L
15. v INSTALL WITH FOUR 1 4 20 FLAT HEAD STAINLESS STEEL SCREWS OR 2 SCREWS PROVIDED 1 94 e 49 3 DIAMETER 1 56 396 DIAMETER 1 Prepare the mounting surface for installation of the bench mounting plate referring to the illustration above 2 Free bench mounting plate from the assembly by removing cotter pin yoke locking nut and stainless steel washer 3 Install the bench mounting plate into the mounting surface using the 14 20 screws provided or longer screws as required 4 Reassemble the yoke to the bench mounting plate per the illustration above For NEMA 4 4X applications replace the cotter pin with a 6 32 x 34 long screw and sealing washer Also insure that the bench mounting plate is sealed between itself and the mounting surface 11 Installation using Pedestal mounting option 7 00 8 00 9 2 50 IN BOTTOM OF PEDESTAL FOR HIDDEN CABLE ACCESS 9 41 1 Prepare mounting surface for installation of pedestal referring to the illustration above 2 Install the pedestal using appropriate hardware and methods for the mount ing surface selected taking strength cable routing and sealing into consid eration 12 NYLON BUSHING CONDUIT ELBOW POSITION AS REGUIRED FOR FREEDOM OF MOVEMENT FOR FLEXIBLE CONDUIT SPACER LIQUID TIGHT CONDUIT m A 1 1 1 2 PLASTIC PIPE NUT TIGH TEN AFTER POSITIONING CONDUIT ELBOW n SEALING
Download Pdf Manuals
Related Search