Home

User's Manual

1. Copyright QVIS All documentation rights reserved 25 What period you would like the motion detect to be active Specify the length of the alarm trigger delay Set an interval period length between alarm activations Which channels to set motion detection upon Tour channel setup PTZ activation time period setup with activation delay option Which channels to allow snapshots from the footage Whether you want an alert message to be displayed Sending an email notification to alert you of the triggered motion sensor alarm need to set email parameters at net service Activating the buzzer local buzzer To upload trigger data through the FTP Set other channels alarm parameter following step 2 and step 3 Note Video blind video loss and alarm input s setup method are similar with motion detection Motion detection menu options Channel Choose the set motion detect channel Enable m means that the motion detect function is on Sensitivity You have six sensitivity levels to choose from Lowest Lower Middle High Higher and Highest Region Click set to enter the set area The area is divided into PAL22X18 Red blocks represent the motion detect defensive area White block means the unfenced area You can set the area as followed Drag the mouse and draw the area Default all selected blocks are the detection area Select Region Copyright QVIS All documentation rights reserved 26 Period Trigg
2. local input mode o Channels 960H 12 20G day channel Storage pase 720P 20G 30G day channel and prep audio 691 2M day channel backu P Backup mode Network backup USB HDD USB writer SATA writer Interface Multi mode input EE Gch RCA Copyright QVIS All documentation rights reserved 88 Network RJ45 10M 100M Adaptive Ethernet port interface PTZ control RS485 support multiple PTZ protocols USB 2 USB ports Hard disk 1 SATA 4TB Max capacity 3G WIFI expand via USB Power 12V 2A dimension 310mm length 215mm width 45mm height For further information and help on any products from the Qvis brand please scan the QR code below to be directed to our website WWW ADATA CO UK Copyright QVIS All documentation rights reserved 89 ENHANCE YOUR DVR WITH OUR WIDE RANGE OF QVIS CAMERAS OUR PRODUCTS ARE FULLY TESTED TO WORK TOGETHER FOR COMPATABLE CAMERAS LOOK FOR THESE COLOUR ICONS ON THE SIDE OF THE BOX L L L L t T d E k F k E k k 960H 720P Recording Recording z Je DON T SETTLE FOR LESS ALL OUR PRODUCTS CARRY QVIS LOGOS Copyright QVIS All documentation rights reserved 90
3. w Bad power supply connection Switch power supply is damaged Firmware update failed to install correctly The hard disk is damaged or the hard disk lines are broken The front panel is damaged The main board of the DVR is damaged 2 The DVR reboots automatically or stops working after boot up a few minutes Possible reasons A moo uw The input voltage is not stable or too low The hard disk is damaged or the hard disk lines are broken The power of the switch power supply is low Frontal video signal is not stable Bad heat radiator or too much dust or bad running circumstance for the DVR The hardware of the DVR is damaged 3 System cannot detect hard disk Possible reasons A B C D The hard disk power supply line is not connected The cables of the hard disk are damaged The hard disk is damaged The SATA port of main board is damaged 4 There are no video outputs in single channel multiple channels and all channels Possible reasons A The program is not matched Please update the program B C The image brightness is all set to O Please restore the default setup There is no video input signal or the signal is too weak Copyright QVIS All documentation rights reserved 79 D E The channel protection or the screen protection is set The hardware of the DVR is damaged 5 Real time image problems such as the image color or the brightness distortion
4. Log information This includes the system operation configuration operation data management alarm affair recording operation user management file management and etc Set the time section to look the date up and click the look up button The log information will display as a list one page is 128 items Copyright QVIS All documentation rights reserved 70 Press Page up or Page down button to look up and press delete button to clear all the log information Type Start Time 2010 08 12 00 00 00 End Time 2010 08 13 00 00 00 Log Time 2010 08 12 10 31 49 2010 08 12 10 31 50 2010 08 12 10 32 30 2010 08 12 10 32 30 2010 08 12 10 32 38 2010 08 12 10 32 38 2010 08 12 10 32 39 Log In User default Log RecoverTime 2010 07 31 11 44 28 Log Out User default Log Log In User admin Logi Save Configuratio Location Save Configuratio Regular 2010 8 12 10 32 35 Cancel Log information Copyright QVIS All documentation rights reserved 71 19 10 4 Version This screen displays the basic information such as hardware information software version issue date serial number NAT status and so on Record Channel 8 Extra Channel 0 Alarm In 8 Alarm Output 1 System V4 00 R10 00000002 1 Build Date 2012 10 26 09 00 26 MAC 260040620002 SerialNo 28822101bdb62d13 Status 209 Nat status Connecting Nat status code 1 202 130 112 247 Version information 20 Web Monitoring 1 When
5. Default 255 255 255 0 Gateway Set the default gateway Default 192 168 1 1 Main Menu gt System gt NetWork Net Card IP Address Subnet Mask Gateway Primary DNS Secondary DNS TCP Port HTTP Port HS Download Transfer Policy Quality Prefer Y Pic 5 Network setting You can manually configure the options above to correctly setup your local network by replacing the default IP addresses with the ones allocated to the current router According to the default setup the default gateway is generally the router IP address so enter IP address e g 192 168 1 10 in the web browser to be able to operate the security surveillance system from different PC terminals within the local network Copyright QVIS All documentation rights reserved 23 17 Alarm Alarm functions include motion detect video blind video loss alarm input and alarm output Abnormality intelligent analysis 17 1 Alarm output Please check current channel status o means it is not in alarming status e means it is in alarming status You can use desktop shortcut menu or click main menu alarm function alarm output to enter the alarm output interface Alarm Output Alarm Type Configuration Manual Alarm output Configuration Alarm is on according to the configuration Manual Click the all button and the according channel is alarming no matter the channel in any state Stop Click the stop button
6. Output adjust starboard distance black margin vertical amp horizontal Automatic Set automatic reboot system and automatic maintenance deleting files Copyright QVIS All documentation rights reserved 13 Resume setup state common setup code setup recording setup alarm setup Restore network setup network service preview playback serial port setup user management Upgrade upgrade with external Upgrade wih etemal devioe ike USB USB hardware X Device Info message Export the device s log or configuration to external device like USB flash disk Input Import Export f l l un the configuration with external device like USB flash disk Hard disk Display hard disk capability and recording information time EL NL code stream information System information s Clear all log information according to the information log video and time Edition l l Display edition information information Shut down KE Logout or reboot Copyright QVIS All documentation rights reserved 14 10 Preview Login normally and choose the multi menu preview status The system date time and channel title are shown in each viewing window The surveillance video and the alarm status are shown in each window see Chart 1 8 s emm _ Chart icons on preview window 11 Desktop Shortcut Menu When in preview mode you can right click on the mouse to get a desktop
7. Possible reasons A When using the BNC output the option between the N mode or PAL mode is wrong and the image becomes black and white The DVR does not match the monitor impedance The video transmission distance is too far or the loss of the video transmission line is too large The color and brightness setting of the DVR is wrong 6 I cannot find the video files in local playback mode Possible reasons A moo uw The data line of the hard disk is damaged The hard disk is damaged Update the different program with the origin program files The video files to look up are covered The recording is not on 7 Thelocal video is not clear Possible reasons A m Bg oC The image quality is too bad The reading program is wrong Reboot up the DVR The data line of the hard disk is damaged The hard disk is damaged The hardware of the DVR is damaged 8 There is no audio signal in the surveillance window Possible reasons Copyright QVIS All documentation rights reserved 80 It does not have an active tone arm It does not have an active sound box The audio lines are damaged The hardware of the DVR is damaged com 9 There is audio signal in the surveillance window but no audio signal in the playback state Possible reasons A Setting issues the audio option is not chosen B The according channel is not connected with the video 10 The time is wrong Possible reasons A
8. right click mouse choose add use mouse to fix several points and then connect them to form an irregular region right click mouse click Yes return to previous page click Yes alarm rule setting if finished tas J YY sitivity High Minimum image distance Sine Sen items stranded items stolen shift llegal parking Rule Sat Rule setting items care Copyright QVIS All documentation rights reserved 35 18 PTZ Control The steps below will explain how simple it is to control a PTZ camera Main Menu System PTZ to set channel parameter protocols etc 1 In order to view the PTZ camera video feed select Preview status to enter single window camera view 2 Right click the mouse button choose PTZ control to control the normal function or choose high speed Click left mouse button to operate the PTZ directly moving the mouse controls the direction of PTZ use the scroll wheel in the middle of the mouse to zoom in or zoom out 3 Operation interface is as followed The functions include PTZ direction control step zoom focus iris setup operation patrol between spots trail patrol boundary scan assistant switch light switch level rotation and so on Note Decoder A B line connects with DVR A B line 4 Click main menu gt system configuration gt PTZ setup to set the PTZ parameters 5 The PTZ functions are decided by the PTZ protocols PIZ
9. Also allows as interfacing with another computer with a serial port connection to perform system maintenance amp upgrades matrix control etc Standard Ethernet network interface fulfills the telecommuting function Important Safeguards and Warnings 1 Electrical safety e All installation and operation here should conform to your local electrical safety codes e We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation 2 Transportation security e Heavy stress violent vibration or water splash are not allowed during transportation storage and installation 3 Installation e Keep upwards Handle with care e Do not apply power to the DVR before completing installation e Do not place objects on the DVR 4 Qualified engineers needed e All the examination and repair work should be done by the qualified service engineers e Weare not liable for any problems caused by unauthorized modifications or attempted repair 5 Environment e The DVR should be installed in a cool dry place away from direct sunlight inflammable explosive substances and etc Copyright QVIS All documentation rights reserved 4 e This series product shall be transported storage and used in the environment ranging from O C to 55 C 6 Accessories e Besure to use all the accessories recommended by manufacturer e Before installation please open the package and check
10. Control 05 5 Zoom Focus 5 Set PTZ Trace Cancel PTZ setup Speed Set the PTZ rotation range Default range 1 8 Copyright QVIS All documentation rights reserved 36 Zoom Click k button to adjust the zoom multiple of the camera Focus Click La button to adjust the focus of the camera Iris Click Ed button to adjust the iris of the camera Hide Current interface will be temporarily hidden after click it Direction control Control the PTZ rotation 8 directions control is supportive 4 directions in Front panel is supportive High speed PTZ Full screen shows channel image Left press mouse and control PTZ to rotate orientation Left press mouse and then rotate the mouse to adjust the zoom multiple of the camera Set Enter the function operation menu Page switch Switch between different pages 19 System Setup Set the system parameters such as General Encode Network Net service GUI display PTZ configure RS485 device RS232 Tour setup Spot and digital Copyright QVIS All documentation rights reserved 37 19 1 General ain Menu gt System gt General System Time 2001 01 12 20 21 50 Date Format YYYY MMC BST Date Separator Time Format 24 HOUR Language ENGLISH HDD Full Overwrite DVR No y Video Standard PAL Auto Logout 0 min Machine Name LocalHost G
11. Setting is wrong B The battery has a bad connection or the voltage is too low C The oscillation is damaged 11 The DVR cannot control the PTZ Possible reasons A There is something wrong with the frontal PTZ B The setting connection or the installation of the PTZ decoder is not correct The connections are not correct The PTZ setting of the DVR is not correct The protocols of the PTZ decoder and the DVR are not matched The address of the PTZ decoder and the DVR are not matched When multiple decoders are connected the far port of the PTZ decoder line A B must connect a 120 resistance to reduce the reflection otherwise the PTZ control is not stable H The distance is too far Copyright QVIS All documentation rights reserved 81 12 The motion detect is not working Possible reasons D O m gt The time range set is not correct The motion detect area set is not correct The sensitivity is too low Limited by some hardware edition 13 cannot login via web or CMS Possible reasons A m The system is Windows 98 ME We recommend updating to windows 2000 SP4 or higher Version or installing the software for low edition ActiveX is not installed or blocked by web browser The version DX display driver is not DX8 1 or later Update the display card driver Network connection failure Network setting issues Invalid password or user name The CMS is not
12. To start off with they have no passwords setup The Admin user account allows unlimited access to the system setup and Guest user account only allows the preview and playback functions to be used User can modify the password of Admin and Guest but cannot modify the authority of them SYSTEM LOGIN User Name ladmin Password Please Login Login Password protection If the password is continuously wrong three times the alarm will start If the password is continuously wrong five times the account will be locked By rebooting the DVR after 30mins after being locked out it will automatically allow access to the system login To prevent this from happening please revise and remember user name and password before logging back into the system Copyright QVIS All documentation rights reserved 9 When you login the system main menu is shown as below Advanced Main Menu Window GI I You have two options Logout or Reboot You can use the desktop shortcut menu or enter the main menu to access the Logout Menu Nl Reboot Logout window Logout Quits the menu Offer password next time you want to log back in Reboot Quits the system Reboot up the system Copyright QVIS All documentation rights reserved 10 Main menu navigation Conf Set the recording configuration recording onfi type and recording time section Record Playback Set recording search recording pl
13. buzzer EMAIL FTP upload Set system time data format language hard disk full time operation machine number video format output mode summertime stay time Set main extra coding parameter code mode resolving ability frame rate code stream control image quality type code stream value frame between value video audio enable Set basic network parameters DHCP and DNS parameters network high speed download Copyright QVIS All documentation rights reserved 12 PPPOE NTP Email IP preview DDNS NetService parameter Set channel title preview hint icon state GUI display transparency cover area time title channel title fold PTZ Set channel PTZ protocol address baud configuration rate date bit stop bit check Set serial port function baud rate date bit RS485 Device stop bit Set patrol mode and interval time 8 Set Set Spttourmode ante tonal tour mode and time interval DI wa channel mode check channel status igita and configure the digital channel etc Set appointed hard disk as read write disc Hard disk read only disc or redundant disc clear management data resume date etc User Modify user team or password Add user management or team Delete user or team Break the connection with the already Management logged in user Lock the account after Online user tools attempted unauthorised access until next DVR reboot Adjust upside downside nearside
14. decided by the stream Copyright QVIS All documentation rights reserved 16 Record Mode Set video state Schedule manual and stop Schedule Record according to the set video type regular detect and alarm and time section Manual Selecting this option will allow you to manually control recording operations on each channel Stop Selecting this option will make the according channel stop recording when it is in any set state Period Set the times during the week when you want the DVR to start and stop recording The recording will start and stop only in the set range Recording Type Regular Selecting this option will initiate regular recording in the set time section The video file type is R Detect Selecting this option will set the motion detect trigger function when there is video blindness blocked camera view or video signal loss When the alarm is set as open recording the Detection recording state is set to on The video file type is M Alarm Selecting this option will set the external alarm trigger signal in the set time section When the alarm is set as Open recording the Detection recording state is on The video file type is A 13 Backup You can back up the video files to external storage device through these setup menus Note The storage must be installed before the file backup If the backup is terminated the already backup can playback individua
15. range is 128 255 Resolution Set the display resolution Channel Choose the set code output channel number Region Cover This means the selective state Click the cover area button and enter the corresponding channel window You can cover the arbitrary using mouse Black region is for output Time display and Channel display set the display position of channel title and time title Copyright QVIS All documentation rights reserved 54 19 6 PTZ RS485 Device This menu will allow you to configure the attached PTZ or other device connected to the RS485 ports on the rear of the DVR PTZ Device RS485 Device Channel 1 Protocol Address Baudrate 9600 Data Bits s Stop Bits 4 MHA Parity None T None Pic 4 37 PTZ configure Channel Choose the dome camera input channel Protocol Choose the corresponding dome protocol PELCOD as an example Address Set the corresponding dome address Default 1 Note The address must be consistent with the dome address Baudrate Choose the corresponding dome baud rate length You can control the PTZ and vidicon Default 115200 e Data bits Includes 5 8 options Default 8 e Stop bits Includes 2 options Default 1 Parity Includes odd check even check sign check blank check Default void Protocol choose related protocol of brand model Address set with correspondi
16. the moving objects meet the picket line rules alarm will be triggered Note when it is overpitched it will show the direction from left to right right to left otherwise it will show the direction from up to down down to up Rules you can choose to forbid bidirectional movement entering or leaving footage frame or movement in 3 different directions so that when the moving objects meet these picket area rules the alarm will be activated Copyright QVIS All documentation rights reserved 31 l Main Menu gt Alarm gt Intelligent Analysis enter video analysis setting interface enable this function Show Traces Sensitivity Hig h 2 Minimum image distance 8 12 Alert Way O Cordon Warning Area Rule setting 1 Click Rule to enter the rule setting interface see pic 8 2 Enable Show traces function adjust the level of sensitivity and minimum image distance The Alert way section will allow you define what type of alarm triggers the system analyses 3 Once you have set your rules you need to set the picket mode choose picket line or picket area Click setting to enter the config interface then right click the mouse and choose Add Use the mouse to set two or more points and connect them to form a line or an irregular area After that has been set an option box of forbidden direction will appear choose one option and right click mouse then click yes return to pre i
17. to enable when alarm triggers there will be red box around moving objects e Sensitivity based on different requirements there are 3 options in the drop down box e Minimum image distance the range is between 0 30 the more flexible the less image distance e Alert way there are 2 kinds cordon and warning area Cordon Can set 3 prohibited directions bidirectional prohibited from top to bottom from left to right from bottom to top from right to left when the setting cordon is too slope show with from left to right from right to left otherwise will be from top to bottom from bottom to top when the moving object meet preset cordon rules the alarm will be triggered Warning area can set 3 kinds of prohibited directions bidirectional prohibited enter and leave when the moving object meet preset warning area rules alarm will be triggered Rules click setting gt enter the rule setting page gt right click mouse gt choose add gt use mouse to fix two or more point gt and then connect them to form a line or an irregular region Once you have done those steps a box of prohibited direction options will appear Choose one of them gt right click mouse gt click Yes gt return to previous page gt click Yes setup is now complete Picket line rules you can forbid bidirectional motion which includes from up to down from left to right from down to up from right to left 2 forbidden directions when
18. write read disk Copyright QVIS All documentation rights reserved 59 IHDD No Status Rea rite Write Normal smapshot Write Normal Write Normal Write Normal Redundant Write Normal Write Normal Format Disk ead only Write Normal Write Normal ition HDD manage 19 9 2 Account Manage the user purview Notes T The character Max length is 8 bytes for the following user and user team name The blank space ahead or behind the character string is invalid The middle blank in the character string is valid Legal characters include letter number underline subtraction sign and full stop There is no limit to the number of users and user groups you can have You can add or delete the user group according to user definition The factory setup includes user admin You can set the team as you wish The user can appoint the purview in the group The user management includes group user The group and user name cannot be the same Each user only belongs to one group Copyright QVIS All documentation rights reserved 60 amp Main Menu gt Advanced gt Account N User Name Group Status admin admin GUI guest user Normal C default user Default Use Delete User t rou Account management Modify User Modify the existing user attribute Modify Group Modify the existing team attribute Modify Password Modify the user passwor
19. 15002 Alarm report m Log report Alarm server setting e Protocol type GENERAL e Enable To tick it means enable e Server IP IP address of Alarm Server e Port Device Port No Alarm Report Tick it means to report alarm information to server Log Report Tick it means to report log to server e Wireless Config ADSL through 3G net card use CMS to visit and config the device Copyright QVIS All documentation rights reserved 49 Enable Type IP Address Wireless Contig Enable Choose Enable to make all settings available e Type Dial type default AUTO Wireless AP 3G access point Dial Number 3G Dial Number User Name User name of 3G Password Password of dial user IP Address IP address obtained from dial Copyright QVIS All documentation rights reserved 50 UPNP UPNP protocol allows you to auto port forwarding on router The precondition of using this function is to make sure the UPNP function of router is enabled Main Menu gt System gt NetSerwce gt UPNP Enable Make sure UPNP is running on router befort using this OK Cancel UPNP Enable Choose Enable to make sure all UPNP settings are available HTTP Router will automatically distribute HTTP port for the device during web browser viewing TCP Router will automatically distribute TCP port for the device when monitoring via CMS Mob
20. 3G module dongle etc 3 3 Monitor connection To view DVR menu and interface system you will need to connect a computer monitor to the device The rear panel has VGA and HDMI video output ports to connect the monitor to 4 Alarm Input and Output Connections 4 1 Alarm input e Alarm input is grounding alarm input e Alarm input demand is the grounding voltage signal e When the alarm is connected with two DVRs or connected with DVR and other equipment it should be isolated by relay 4 2 Alarm output e Alarm output cannot be connected to a high power load no more than 1Amp e When forming the output loop you must prevent high current levels from damaging the relay Please use the contact isolator when there is a high power load Copyright QVIS All documentation rights reserved 7 4 3 PTZ decoder connections e Make sure the grounding of the PTZ decoder and DVR are shared otherwise the common mode voltage will lead to the PTZ control failing It is recommended to use shielded twisted pair e Try to incorporate precautions to prevent electrical damage from an unstable mains power source Please use surge protection devices or uninterruptible power supplies e Inthe outlying end connect 1200 resistance paralleled to reduce inflections and insure the signal quality e The 485 AB lines of DVR cannot be connected with other 485 output equipment in parallel e The voltage between the AB lines of the decoder must be less th
21. Cannot see the preview picture the digital channel Possible reasons Did not add device The device of related channel was not enabled The device of related channel was not selected The selected device did not connect to video sources The channel title of selected remote device does not exist Stream for remote channel was set by extra stream User name amp password not matched I o T m oo wo gt Directly inputted the IP address or port No incorrectly when adding device The resolution of added device is too large to display by the monitor 24 Click search why not search out any of the device Possible reasons A There is no other device existing within the Local area network B The subnet mask setting is incorrectly in the Network settings 25 The snapshot at alarm function was enable why not catch picture Possible reasons A HDD manage without partition for snapshot B Partition for snapshot is 0 C The snapshot function is not enabled on record gt storage of related channel 26 The time shows on digital channel is not the same as local side A Enable the time synchronise function of the digital channel 27 Cannot see preview picture of analog channel Possible reasons A The camera did not connect to video interface Copyright QVIS All documentation rights reserved 85 B The device did not connect to video source C Video source is broken 28 Picture will be frozen when multi co
22. Cun cel Enable Click Enable then all settings will become available e Server IP IP address for FTP server e Port Domain Port of FTP default 21 e User Name User name of FTP e Password Password of user Anonymous enable anonymous no need to set user name and password Copyright QVIS All documentation rights reserved 47 Max File Length Max length for upload files for every data packet default is 128MB Dir Name The directory of the upload file Note Only Users are to upload files only have permission clearance to do So ARSP Startup DDNS server to add devices and manage it in the DDNS server ARSP Type DNS m Server IP 192 168 1 112 Port 15000 User Name test Password s Update Period 1 ARSP Type choose DNS Enable m means it is chosen Sever IP IP address of DDNS server Port Port No of device related DDNS server listen port User name the user name that device can log in DDNS server Password the password related to the user name Refresh cycle Time interval between device and DDNS when synchronised Note Please set up server before using DDNS Copyright QVIS All documentation rights reserved 48 Alarm center When the alarm has been triggered you can send report alarm information to the alarm server AlarmServer Protocol Type GENERAL ni Enable m Server Name AlarmServer Port
23. IP address in the IP address and obtain the current IP address Then use this IP address to visit the DVR through user port NTP setup Enable min OK Cancel NTP The NTP server must be installed in the PC Enable Reverse mg mean choose setting can become effective e Host computer IP Input the IP address installed NTP server e Port Default 123 You can set the port according to NTP server e Time zone e Update Period The same with the NTP server check interval Default 10minutes EMAIL setup If the alarm is triggered or the alarm snapshots are taken you can setup the DVR to send an email containing alarm information and the photos to an appointed email address Copyright QVIS All documentation rights reserved 44 Main Menu gt System gt NetService gt EMAID Enable 9 SMTP Server Your SMTP Server Port 25 Need SSL User Name Password Sender Receive Title Alarm Message OK Cancel EMAIL e SMTP server Email server address It could be an IP address or domain name Domain name can be translated only it is the correct DNS configuration Port Email server port number SSL Decide whether using Secure Socket Layer protocol to login User Name Apply the email server user name Password Input the password corresponding to the user Sender Set the email sender address Receiver Send the email to appointed receivers when the alarm is turned on You can set three receiver
24. Key Back up options File information File searching File backup Operation playback time code Playback control panel Copyright QVIS All documentation rights reserved 21 Backup options Choose the file to playback backup File information Displays Start time end time and size The storage must be large enough before the file backup begins File searching Search for specific files according to the search parameters File Backup Displays the backup files stored on the HDD Operation playback time code Displays the current time code and selected playback operation Playback refer to the following sheet for full explanation Button Function n PlayPause Reverse Play s E e Chart 2 Playback controls key Note Frame by frame playback can only be performed in the Pause playback State Special functions Accurate playback Input time h m s in to the time column and then click playback Local zoom When the system is in single window full screen playback mode you can drag your curser on the screen to select a section and then left click mouse to local zoom in or out You can right click mouse to exit Copyright QVIS All documentation rights reserved 22 ILI MEN To configure network settings Main Menu System Network IP address Set the IP address Default 192 168 1 10 Subnet Mask Set the subnet mask code
25. Max Resolution This Resolution Connection Status Copyright QVIS All documentation rights reserved 57 For example ga Channel status Channel Max resolution 5 Resolution Connecti alus _ AL UM Par DN CIF Di Connected CALNE A t When a channel is added to the device but it is not enabled Not Configured will be displayed status Channel Max resolution This Resolution Connection 5 b T 2 mt lt a P Lr e XR CUN LLEGUE AMA NS PELLE WEE LR tah Td a e a S M D1 Connected Copyright QVIS All documentation rights reserved Remark when the current resolution is over the max resolution that the channel supported then a red X will be shown on the preview image 19 9 Advanced Manage tools menu including HDD manage account manage online user output adjust auto maintain upgrade 19 9 1 HDD Manage Configure and manage the hard disk The menu displays current hard disk information hard disk number input port type status and overall capability The operation include setup the write read disk read only disk redundant disk hard disk format resume default Choose the hard disk and click the right function button to execute Note Read Write Disk The equipment can write or read data Read only Disk The equipment can read data but can not write data Redundant Disk Double backup the video files in the
26. On the playback page choose the video file press play or double click the file to play back Copyright QVIS All documentation rights reserved 77 23 File storage The device introduces several unique storage and backup techniques to achieve multiple storage and backup modes 171 Real time storage Redundant storage the device allows RAID1 storage configurations to achieve two hard disks storing simultaneously as a mutual backup USB HDD and removable hard disks supporting video files that are written in real time to these types of storage devices DVD RW the most recent real time storage technique adaption supporting video file which are burnt real time to CD Real time remote storage the device supports storing video files in real time to a remotely connected data storage device 17 2 File download Using U disk and movable hard disk download at local device the device supports the chosen file are high speed backup to the storage devices DVD RW selected video files are burnt and stored on to CD Network high speed download you can quickly download the selected files via the remote client 24 FAQ Troubleshooting If the problems are not listed please contact the local service or call the HQ service We are willing to offer the service 1 The DVR cannot boot up normally Possible reasons A The power supply is not correct Copyright QVIS All documentation rights reserved 78
27. Playback Enter playback area can support multi channel playback at the same time Log Show with log information Local config To set device alarm enable to linkage function on the remote network client side Channel control Open the video choose the video on the left video window and then choose channel on the right double click it to open the first video choose another one channel double click to open the second video use the same way to open other channels If the channel did not change system will closed previous video and open the new one you choose Note User can choose the most appropriate image mode when opening remote video control Copyright QVIS All documentation rights reserved 74 e Close video at the video window choose the video that you want to turn off right click it and choose shut the window also can choose shut all the windows to close all the video Remote config device On the preview window single click right mouse button and choose a device to configure You will be given options to set parameters for the device which will be synchronised to local network You will be able to set options for record alarm system advanced Info etc 21 Special Function These series of DVRs also have added options to help increase the variety of customisable setups The main options you can configure are Video encoding resolution amp compression codex Multi channel playback Video data streamin
28. QCIF 64 512kbps 1080P 1024 8196kbps When using the Video Audio tick boxes at the bottom of the options list the video tick box will automatically highlight when you tick the audio tick box Audio is optional depending on the camera connected to the iDVR Video signal is always streamed and recorded Extra stream config Extra stream is used for client side and mobile device monitoring using mobile apps In order to allow for remote mobile device monitoring enable the Extra stream by clicking on the drop down tab at the top of the second column then configure the frame rate code stream value the setting way in the same method that was used to setup the separated channel parameter see 14 2 Copyright QVIS All documentation rights reserved 76 22 Multi channel playback The 4 channel device can achieve 4 channels of playback at the same time likewise for the 8 16 channel device You can combine a number of desired video feed channels in a variety of configurations within the monitor windows on the playback page n m aA SF SOR 46 Pic 11 Playback To combine different channels together please follow these steps 1 Main Menu gt Record gt Record to set the record parameter for each channel Enter playback the interface and click the Search key On the search condition interface choose file type choose channel channels can be combined freely choose time period click yes 4
29. QUIS 4 8 16 CHANNEL HDA DVR PIONEER 4 PIONEER 8 PIONEER 16 User s Manual V1 0 12 2014 Important Safeguards amp Warnings Front amp Rear Panels Basic Information Alarm Input amp Output Information Startup Turn Off Login Logout Main Menu 10 Preview 11 Desktop Shortcut menu 12 Recording Config 13 Backup 14 Snapshot Storage 15 Playback 16 Network Setup 17 Alarm 18 PTZ Control 19 System Setup 20 Web Monitoring 21 Special Function 22 Multi Channel Playback 23 File Storage 24 FAQ Troubleshooting Appendix 1 Remote controller operation Appendix 2 Mouse operation Appendix 3 Detailed Specification OI GON Copyright QVIS All documentation rights reserved WELCOME Thank you for purchasing the 4 8 amp 16 Channel High Definition Analogue Pionner DVR This user s manual is designed to be a reference tool for your CCTV system The product series has an array of integrated features which gives great practical advantages to the user As well as being able to record in full D1 25fps real time it can also provide high definition 720p quality recorded footage 12fps HDA The system incorporates intelligent analysis of incoming video footage to ensure only relevant information is recorded For added ease of use the DVR is designed so that it offers a streamlined setup process The user can achieve great ease of use applicability expansibility and detailed
30. all the components are included e Contact your local retailer ASAP if something is broken in your package 2 Front amp Rear Panels 2 1 Front Panel 2 4 6 8 10 12 1416 18 20 22 24 1 3 5 7 9 11 13 515447 19 21 23 Shift naon dg Next File 17 Record light System ready Slow Play ESC button indicator light i Alarm indicator Fast Play k Function Switching light Copyright QVIS All documentation rights reserved Me eu emer indicator light Pause Outside Play Pause Select confirm operation button indicator light Network Ili switch indicator light 7 HDD indicator Next Frame remote receiver light Previous File Play USB port external storage 2 2 Rear Panel 16 Channel device shown below BNC Video RCA Audio inputs output Ethernet Internet Copyright QVIS All documentation rights reserved 6 3 Basic installation 3 1 HDD installation Please install the Hard disk before using this product for the first time Please connect the HDD power and data cable correctly our product can support 1 or 2 or 4 or 8 HDDs How many HDDs it can support depends on which kind of product the buyer purchases Note the device can run normally without HDD but cannot do record and playback 3 2 Mouse connection To connect the mouse you have the option of using either of the two USB ports attached to the rear panel Both can be used for a mouse flash disk WIFI or
31. an 5V 4 4 Front equipment grounding note e Bad grounding can lead to the burnout of the internal chipset 4 5 Alarm input type unlimited e The DVR alarm output port is set to a constant opening type Once you have setup the peripheral device connections HDD installation and turned on the power to the DVR turn on the power switch located on the back panel The indicator on the front panel will illuminate which will signify the device has turned on successfully After starting up you will hear a beep the default output to the monitor is the multi window mode Note If the circumstance occurs when the power is abnormal or has been cut please switch off the device When you switch the power back on the DVR will automatically recover its previous state before it had been shut down 6 Turn off There are two methods to turn off the DVR either the soft switch or the hard switch Soft switch Entering Main menu and choosing Logout in the turn off the system option Hard switch Pressing the power supply switch Copyright QVIS All documentation rights reserved Note The settings information must be saved before replacing the battery otherwise information will be lost When the DVR boots up in order for the user to access the operating system s functions they must login via the System Login window see next image There are two user settings available which are admin and guest
32. and the according channel stops alarming no matter the channel in any state Copyright QVIS All documentation rights reserved 24 17 2 Motion Detect ES Main Menu gt Alarm gt Motion Detect Channel Enable Sensitivity Middle M Repion Set Period s et Interval scc Alarm Output m Delay Record Channel 1 2 6 GJGJ GG A east sash COE CGUGG gi PTZ Activation Dela nm Show Message Send Email J m FTP upload D i Motion Detect Motion detection setup Within this configuration menu you are given setup options to activate a number of elements of the motion detection feature This includes setting up the alarm trigger linkage record and also to instruct a PTZ camera to move to a preset position for when the motion sensor has detected movement between certain periods of time To set these options Choose Main Menu gt Alarm gt Motion Detect then enter the setup interface Choose the camera channel you want to set and adjust the sensitivity level You will also be able to adjust the time period of alarm surveillance Set the monitor area click the Set button next to Region select the areas you want the Default setting will make all areas motion sensitive then right click to choose Up window In the second section of the motion detect options you can customise
33. ay and Storage video file storage Detect backup device format device and Backup f backup the selected files Set the motion detect alarm channel sensitivity area linkage parameters Motion defending time section alarm output detection screen hint recording screen shot PTZ patrol buzz email and FTP upload Set camera mask alarm channel sensitivity linkage parameters defending time section alarm output screen hint recording screen shot PTZ patrol buzz email and FTP upload Set video loss alarm channel linkage parameters defending time section alarm output screen hint recording screen shot PTZ patrol buzz email and FTP upload Copyright QVIS All documentation rights reserved 11 System configuration Alarm output Exception handling Intelligent analysis General configuration Encode configuration Network configuration Set alarm input channel equipment type linkage parameters defending time section alarm output screen hint recording screen shot PTZ patrol buzz email and FTP upload Set alarm mode configuration manual shut down No HDD HDD error HDD capacity is not enough network cut IP Conflict linkage parameters screen hint or buzz alarm Set algorithm rule trajectory display sensitivity minimum pixel alert mode and setting linkage parameters period alarm output screen prompt record PTZ tour
34. connecting to a network use the browser on your PC to login to the DVR to use the remote control functions To do these please follow the steps below 2 Install the ActiveX file name is IE Plug V1 1 0 78 exe which can also be located on the DVR CD ROM disc follow the instructions on how to install it Copyright QVIS All documentation rights reserved 72 3 Connect with device open browser input the IP address of device for example the IP is 10 2 2 88 then input http 10 2 2 88 at the address column will enter below page WEB login interface 4 Log in by inputting your user name and password If you choose to link with all the videos after login you need to choose the network stream LAN networks use the main stream to transfer whilst WAN networks use the extra stream to 5 transfer If network bit rate is poor what may improve video transfer rate will be to choose an extra stream The default administration login user name is admin there is no password to enter leave blank User should create a password for the admin user profile after login Pic 9 is the interface view you will encounter after successfully logging in Copyright QVIS All documentation rights reserved 73 EL ELT WEB interface Basic remote control operation The control interfaces shown in Pic 9 have a number of functions that are described below Screen Split To choose the mode of preview
35. d You can set 1 6 bit password The blank ahead or behind the character string is invalid The middle blank in the character string is valid Note The user who possesses the user control purview can modify his her own or other users password Copyright QVIS All documentation rights reserved 61 Main Menu gt Advanced gt Account gt Modify Pass x User Name ladmin Jn New Confirm OK Cancel Modify password Add user Add a user into the group and set the user purview Enter the menu interface and input the user name and password Choose the team and choose whether cover using the user Cover using means that the account can be used by multiple users at the same time Once you have chosen the team the user purview is the subclass of the team We recommend that the common user s purview is lower than the advanced user Copyright QVIS All documentation rights reserved 62 Main Menu gt Advanced gt Account gt Add User User Name Kcuseable n a 3 Authority Shutdown the device Channel Title Schedule Backup HDD Management PTZ Control Add User Add Group Add a user group and set the purview There are 33 different purviews Which allows you to either shut down the equipment real time surveillance playback record setting video backup and more Copyright QVIS All documentation rights reserved 63 Name Memo Authori ty Channel Title schedul
36. d version info 19 10 1 HDD info This interface displays the hard disk state hard disk type overall capability residual capability the recording time etc l Z Main Menu gt Info gt HDD Info N Capacity Left Capacity Status Read Write 58 29 0 00 MB Normal Read Write 21 69 0 00 MB Normal Read Write 79 99 69 83 GB Normal Read Write 79 99 79 99 GB Normal Read Write 79 99 79 99 GB Normal Read Write 79 99 79 99 GB Normal Read Write 79 99 79 99 GB Normal Read Write 79 99 79 99 GB Normal Read Write 79 99 79 99 GB Normal HDD info Tips means that the hard disk is normal X means that the hard disk is broken down LUN means that there is no hard disk If the user needs to change the damaged hard disk you must shut down the DVR and take out the damaged hard disk then install a new one Copyright QVIS All documentation rights reserved 5 Having this asterix behind the serial number shows which disk is the main current working one If the corresponding disk is damaged the information will show 19 10 2 BPS This screen displays the code stream Kb S and hard disk capability MB H in real time It displays the information in a wave sketch map et Main Menu gt Info gt BPS N Channel Kb s Channel Kb S 1054 9 1043 1054 10 1043 1054 ll 1043 1043 2 1043 1043 1043 1043 1043 1043 A 1043 1043 1043 BPS 19 10 3 LOG This is to search the log information database using a set search mode
37. e Iz Backup EJ HDD Management Iz PTZ Control Account Iz Query System Info Iz Query Log Info I Clear Log Add group e Delete User Delete the current user Choose the user and click the delete user button Delete Group Delete the current group Choose the group and click the delete group button Copyright QVIS All documentation rights reserved 64 Te ner mera te x Main Mcnu gt Advanced gt Account gt sDelete Group GROUT Name admin L Memo administrator group Delete Group 19 9 3 Online user To check the information of network user that connected with local device also can tick the selected user to break up connection make Y at the box then the user will be frozen after connection stopped and will not log in until device reboot amp Main Menu Advanced Online User User Online user Copyright QVIS All documentation rights reserved 65 19 9 4 Auto Maintain The user can set the time to auto reboot and auto delete file IX Main Menu gt Advanced gt AutoMaintal 4uto Reboot System Every Thursday at 01 00 ba Auto Delete Old Files Never sd OK Cancel Auto maintain 19 9 5 Restore The system can be restored to its default settings You can choose the items according to the menu E Main Menu gt advanced gt Restore le selec lefuull Sciccet larin Sel Netservice Display R5237 Ac
38. e the video file is the video and audio multiplex stream Extra stream Settings Extra stream is used for client side monitoring amp mobile monitoring Channel title select channel title and then to choose whether need enable video amp audio The resolution frame rate bit rate type settings is the same as main stream 19 3 Network Setup Main Menu gt System gt Network Net Card Wire Netcarc L DHCP Enable IP Address 492 168 1 10 EE Subnet Mask 255 255 255 0 Gateway 192 168 1 Primary DNS 192 168 Secondary DNS 8 Media Port 34567 HTTP Port 80 HS Download L Transfer Policy Quality Prefe o Network Menu e Net Card You can choose cable network card or wireless network Copyright QVIS All documentation rights reserved 41 card DHCP Enable Obtain IP address automatically not suggested Note DHCP server is preinstalled IP address Set the IP address Default 192 168 1 10 Subnet mask Set the subnet mask code Default 255 255 255 0 e Gateway Set the default gateway Default 192 168 1 1 DNS setup Domain Name Server This translates the domain name into an IP address The IP address is offered by network provider The address must be set and reboot then it works e Media port Default 34567 e HTTP port Default 80 e HS Download Transfer Policy There are three strategies self adaption image quality prec
39. edence and fluency precedence The code stream will adjust according to the setup Self adaption is the tradeoff between the image quality precedence and fluency precedence Fluency precedence and self adaption are valid only when the assistant code stream is turned on Otherwise image quality precedence is valid 19 4 Net Service Choose the network service option and click the set button to configure the advanced network functions or double click the service button to configure the parameters Copyright QVIS All documentation rights reserved 42 main Menu gt System gt NetService Net Server Net Server Info PPPoE 0 NTP 0 NTP 10 EMAIL 0 Your SMTP Server 25 IP FILTER 0 0 0 DDNS Set Invalid 0 FTP 1 xmsecu com 15000 AlarmServer 1 192 168 0 101 Wireless Config Not enabled Mobile Monitor 0 34599 UPNP Wifi Not enabled RTSP 1 554 Cloud Enable ood NetService Menu PPPoE setup Main Menu gt System gt NetService gt PPPOE Enable Copyright QVIS All documentation rights reserved 43 PPPOE e Enable Reverse m means choose setting can become effective Input the user name and password that ISP Internet service provider provides After saving it reboot up your system Then the DVR will build a network connection based on the PPPoE The IP address will change into dynamic IP address after above operation is well done e Operation After PPPoE dialing has successfully looked up the
40. eneral setup System time Set the system data and time Date format Choose the data format YMD MDY DMY e Date Separator Choose list separator of the data format e Time Format Choose time format 24 hour or 12 hour e Language supports 29 languages Arabic Czech English Finnish Greek Indonesian Italian Japanese Portuguese Russian Thai T Chinese S Chinese Turkish Brazilian Bulgarian Farsi French German Hebrew Hungarian Polish Romanian Spanish Swedish Vietnamese etc e HDD full Choose stop record Stop recording when the hard disk is full e Choose overwrite Cover the earliest recording files and continue recording when the hard disk is full DVR No Only when the address button on the remote control and Copyright QVIS All documentation rights reserved 38 the corresponding DVR number is matched then the remote operation is valid e Video Standard PAL or NTSC e Auto Logout Set the latency time in the range of 0 60 0 means no latency time e Machine Name Set the device s name DST Choose the summer time option and the pop up dialog box appears E Enable Day of Week Date Statt Jan 01 01 End jan st 01 01 DST week Enable Day of Week Date Stat 01 01 End 201 01 01 01 01 DST date 19 2 Encode This menu will allow you to set the video aud
41. er the motion detect signal in the set time section You can set according to week or you can set uniformly Each day is divided into four time sections Set Saturday 00 00 24 00 00 00 24 00 00 00 24 00 00 00 24 00 D 6 S 2 15 46 21 24 Sun A ECETIDGICE EIS E DERI 68 3 35 SS PD E 2 E3 SD 39 25 Tue R B 58 B 83 BS 8 ES SSR Es EZ EB G 3 E sp S Set the time section Interval Only one alarm signal is turned on even there are several motion detect signals in the set interval Alarm output Start the external equipment of corresponding linkage alarm when the motion detect alarm is turned on Delay Delay a few moments and stop when the alarm state is turned off The range is 10 300 seconds Record channel Choose the recording channel multiple option supportive Trigger the video signal when the alarm is turned on Note Set in the recording setup and perform the linkage recording Start detecting video files in the corresponding time section Tour m means that the selective channel is single window alternate patrol preview The interval is set in the Main Menu gt System gt Tour PTZ Activation Set the PTZ activation when the alarm is turned on Note to link PTZ you need to go Shortcut menu gt PTZ control to set preset point cruise between points amp interval time
42. etc Copyright QVIS All documentation rights reserved 27 PTZ Activation CAM 1 None CAM 2 None CAM 3 None CAM 4 None PTZ Activation under hybrid mode Delay When alarm is over recording will last some seconds 10 300sec then stop Show message Pop the alarm information dialog box in the local host computer screen Send EMAIL mg means sending an email to user when the alarm is turned on Note Set in the NetService and send email FTP upload to tick it the video amp picture of related record channel amp snapshot channel will be uploaded to assigned position Note FTP upload need be set at Netservice e Buzz When alarm is triggered the device will emit a buzzing sound 17 3 Abnormality The DVR s operating system will constantly scan the current software and hardware of the device for any abnormal events such as No Disk No hard disc drive available Disk Error No Disk Space Network Disconnection IP Conflict IP address is incorrect for remote connection If one of these system errors occurs the device will alert you with such as show message and buzzer Copyright QVIS All documentation rights reserved 28 Main Menu gt Atlarm Abnormality Event Type No Disk nable m Show Messe 31 Abnormal menu screen Event Type Selecting abnormity you want to inspect Enable Select it to make sure abnormal function workable Show me
43. g rates File storage and backup 21 1 Encode In the encode option menu screen shown below See image below you can setup the best video encoding parameters to suit the data transfer speeds of your network connection Having a high resolution and compression setup will work best on a network with a high bit transfer rate Otherwise video frame rate may drop and cause lagging to occur In order to achieve the best quality video playback on the network that you are connected to adjust the settings accordingly until the desired quality level of video monitoring has been achieved ear Encode Copyright QVIS All documentation rights reserved 75 21 2 Separated channel encode settings Follow steps below to encode separated channels 1 Local operation Main Menu gt System gt Encode alternatively right click on the window for the remote setting and then choose Device Config at System gt Encode 2 Select channel one set resolution to D1 frame rate at 20 byte rate value 1024 3 Select channel two set resolution to CIF frame rate by 25 byte rate value 512 Right click once on it or select Advanced and click copy 4 Select channel three and either right click once on it or choose the Advanced option select paste To make it the same as channel four Note video resolution network data transfer requirement speeds Video Encode Required bit rate CIF 64 1024kbps
44. gs for the alarm are not correct The alarm output is turned on manually The input machine is damaged or the connections are not correct There are some problems for specific program edition Please update the program Copyright QVIS All documentation rights reserved 83 19 Alarm is not working Possible reasons A B C D The settings for the alarm are not correct The connection of the alarm is not correct The alarm input signal is not correct Alarm is connected with two synchronous loops 20 The remote controller is not working Possible reasons A B C D The remote control address is incorrect The remote control distance is too far or the angle is too large The battery has fully discharged The remote controller or the front panel of the recording machine is damaged 21 The storage time is not enough Possible reasons A Front Vidicon quality is bad The lens is too dirty The Vidicon is in a poor backlighting installation location The hard disk capability is not enough The hard disk is damaged 22 The downloading files cannot play Possible reasons A B C D There is no media player There is no DX8 1 software or higher edition There is no DivX503Bundle exe file to play AVI video files The DivX503Bundle exe and ffdshow 2004 1012 exe files must be installed in the windows XP system Copyright QVIS All documentation rights reserved 84 23
45. ile Port Router will automatically distribute Mobile Port for the device when using your smart phone to monitor the DVR Copyright QVIS All documentation rights reserved 51 WIFI The DVR connects to wireless router via WIFI module then it visits it through the IP address the precondition of using this function is to make sure the DVR have connected with WIFI modern Wifi SSID__ Authentication Signal _ OPEN Very Low Enable SSID Password IP Address subnet Mask Gateway WIFI configure Search click search to search all the available wireless device in current range enable tick it to enable firstly then go for further setting auto obtain IP address tick it to enable device will auto obtain a WIFI IP SSID wireless LAN name auto match to the wireless device u connected Password wireless network password of router IP address to set the IP address of device default is 192 168 1 12 subnet mask set subnet mask of device default is 255 255 255 0 gateway set gateway of device default is 192 168 1 1 Copyright QVIS All documentation rights reserved 52 RTSP Surveillance via cross browser Safari Firefox Google chrome and also using VLC software This function only for monitor but cannot control the device Enable S Port 554 OK Cancel RTSP setting Enable m means enable tick it firstly before setting e Port the default p
46. io code parameter video file remote monitoring and so on Set every main stream parameter in the left part and then set the extra stream parameter in the right part Copyright QVIS All documentation rights reserved 39 Note extra stream introduces a video compression technique that was applies to multi channel simultaneous playback Dial up multi channel real time monitor working under poor bandwidth strength or for mobile monitor etc Main Men fo GG TED Picture 4 20 Encode setup Independent channel code setting Channel Choose the channel number e Compression Standard H 264 main profile Resolution Resolution type 1080P 720P 960H D1 HD1 CIF QCIF Frame Rate P 1 frame s 25 frame s N 1 frame s 30 frame s Bit Rate Type You can choose limited code stream or variable code stream When you choose the variable code stream there are six image quality options Under the limited code stream you can choose the code stream manually Bit Rate Set the code stream value to modify the image quality The larger code stream value the better image quality 1080P 1024 8192kbsp T720P 1024 4096kbps 960H 869 4096kbps D1 512 2560kbps HD1 384 2048kbps CIF 64 1024kbps QCIF 64 512kbps Copyright QVIS All documentation rights reserved 40 Frame Interval can choose the range 2 12s Video Audio When the icons are all displayed in revers
47. lly Copyright QVIS All documentation rights reserved 17 Main Menu gt Record gt Backup E sdb1 USB DISK 528 06 MB 1 86 GB Backup option screen Detect Detect the storage connected with the DVR such as hard disk or universal disk Backup Click backup button and the dialog box is popped up You can choose the backup file according to the type channel and time Copyright QVIS All documentation rights reserved 18 Backup R Type M Read Write Channel 1 M Start Time 8 2001 01 11 00 00 00 Remover End Time 2001 01 11 22 51 45 Egg 3 IL Channel File Name Length 2 01 2001 01 11 22 16 19 22 17 17 R 288 00 KB 3 801 2001 01 11 22 17 55 22 51 40 R 7 18 MB Required Remaining 8 22 MB 528 06 MB Backup format H264 7 meane Backup option screen 2 Remove Clear the file information Add Show the file information satisfying the set file attributes Backup format configure the backup file format according to what you require You can choose between two different formats which are H 264 or AVI Start pause Click the play button to start the backup and click the pause button to stop the backup Note During backup you can exit the page layout to carry out other functions Burning the file will be burned synchronously after you have clicked this Erase Choose the file you wish to delete and click this button to delete the file e Stop Stop the back
48. matched the DVR program version 14 The image is not clear or there is no image in network preview state or video file playback state Possible reasons gt Network is stable The user machine is resource limited Choose the play in team mode in the network setup of DVR The region shelter or channel protection is set The user has no surveillance purview The real time image of the hard disk recording machine itself is not clear Copyright QVIS All documentation rights reserved 82 15 Network connection is not stable Possible reasons A B C D Network is not stable IP address is conflicted MAC address is conflicted The net card of the DVR is bad 16 There is something wrong with the USB backup or writing a CD Possible reasons A The rewritable machine and the hard disk are shared the same data lines There is too much data to backup Please stop recording and backup on another device The backup equipment is not compatible The backup equipment is damaged 17 The keyboard cannot control the DVR Possible reasons A B C The serial port of the DVR is not set correctly The address is not correct When multiple transformers are connected the power supply is not large enough Please give each transformer individual power supply The distance is too far 18 Alarm cannot be recessional Possible reasons A B C D The settin
49. ng address default is 1 Baud rate choose the baud rate that the related device uses default is 115200 Data bits including 5 8 options default is 8 Copyright QVIS All documentation rights reserved 55 Stop bits includes 2 options default is 1 Parity Include odd check even check sign check blank check Default void 19 7 Tour Function This menu will allow you to set the patrol routine of the DVR This means that the tour mode has been enabled You can choose the single view four view six view of the single mode tour Main Menu gt System gt Tour Enable Tour 7 Interval 5 View 1 1 View 4 Alarm Tour Type Interval 5 Return after finished Tour configuration menu interval Set the patrol switch interval The set range is 5 120 seconds alarm tour set the interval to shift alarm tour range is 5 120 seconds choose return when alarm ends when alarm link to tour system will auto shift to six view after alarm finished Copyright QVIS All documentation rights reserved 56 Remark at preview mode click upper right icon 8 Turn on Turn off tour 19 8 Channel Management Manage each camera s channel status and mode we Main Menu gt System gt Digital LE Set channel mode Initial channel manage screen Channel Status This menu screen shows the status of the entire range of available channels the information includes
50. nnection and shift devices A Picture come out from digital channel need few seconds shift device means to show new picture so it needs several seconds to buffer Appendix 1 Remote controller operation 1 Multichannel button Multi channels preview Password input number input channel Number button put put switch Direction button Direction and OK button Playback operate Playback Basic operation 5 Recors control Enter into record menu Copyright QVIS All documentation rights reserved 86 Remote controller Input the number of DVR to control it Appendix 2 Mouse operation Take right hand column as an example Double click one item in the file list to playback the video Double click the playback video to zoom in or out the screen Double click the channel to make it preview in full screen display Double click again to resume the multi channel display Double left click Em 7c HN Copyright QVIS All documentation rights reserved 87 Drag mouse the motion detect area Be the cover area Appendix 3 Detailed Specification Main processor Hi 3531 Video H 264 High Profile compression IMERCTEEERUONWEN Video Playback 1 AHD M Pure Analog 16 AHD M 8 AHD M 16 AHD L Mixed 4 AHD M Analog 4 720P IP IP 1 1080P 8 720P 4 1080P 20 960H Audio 711 Audio compression Recording Manual gt alarm gt motion detection gt timing and Playback Plavback 4
51. nterface click yes to finally finish alarm rules setting 4 Next you need to set the alarm control period steps The taken linkage measures are the same as step 2 and step 3 in Alarm setting 10 1 Copyright QVIS All documentation rights reserved 32 5 When video analysis alarm is triggered there will be red box line in the preview image The intelligent analysis function mainly includes the 2 facets detailed below Touch line detection bidirectional touch line single direction touch line Copyright QVIS All documentation rights reserved 33 17 5 Items care gt Show traces tick this to enable when this function is triggered there will be a red box shown around the moving object gt Sensitivity based on different requirement there are 3 options in the drop down box gt Minimum image distance range between 0 30 the more flexible the less image distance gt Alert way three modes available Items stranded object appears within warning area and the size of object meets the rules of minimum image distance alarm will be triggered see image below Items stolen object disappears within warning area and the size of object meet the rules of minimum image distance alarm will be triggered Copyright QVIS All documentation rights reserved 34 Illegal parking this way is similar to Items stranded see image below Rule click Set enter the setting page of rule
52. ort is 554 19 5 GUIDIsplay Configure the video output parameters including the front output mode and encode output mode Front output The local preview mode includes channel title time display channel display record status alarm status transparency and region cover Encode output In the network surveillance and video file mode include channel title time display channel display record status alarm status transparency and region cover Copyright QVIS All documentation rights reserved 53 E Main Menu gt System gt GUI Display Channel Title gt Set Time Display Channel Title Record Status Alarm Status Deflick Transparency 175 Resolution 1920 1080 VGA priority v Channel 4 L Region Cover Time Display Channel Title Noc The GUI display menu Channel Title Click the channel name modify button and enter the channel name menu Modify the channel name Time Display This means displaying the selective state Display the system data and time in the surveillance window Channel display This means the selective state Display the system channel number in the surveillance window Record Status This means the selective state Display the system recording status in the surveillance window Alarm Status This means the selective state Display the system alarm status in the surveillance window Transparency Choose the background image transparency The
53. s at most e Title You can set as you wish IP Filter setup When choosing the white list only the listed IP address can connect to the DVR The 64 IP addressed are supportive in the list When choosing the black list the listed IP address cannot connect to the DVR The 64 P addressed are supportive in the list You can delete the set IP address by v in the options Note When the same address is in the white and black list at the same time the black list precedence is higher Copyright QVIS All documentation rights reserved 45 IP Filter DDNS Muin Menu gt System gt NetService gt DDNS DDNS Type Enable DDNS setup Copyright QVIS All documentation rights reserved 46 DDNS Dynamic Domain Name Server Local domain name Provide the domain name registered by DDNS User name Provide the account registered by DDNS Password Provide the password registered by DDNS When the DDNS is successfully configured and start you can connect the domain name in the IE address column to visit Note The DNS setup must be configured correctly in the network setup FTP setup FTP is available only when alarm is triggered or alarm activates record and snapshot functions it will upload the related record and snapshot pictures to FTP server Main Menu gt System gt NetService gt P alli User Mam c Password OK
54. shortcut menu to appear shown below The menu includes main menu record mode playback PTZ control High Speed PTZ Alarm Output color Setting Output adjust Logout view mode shift spot Main Menu Record Mode PlayBack PTZ Control 9 HighSpeedPTZ t Alarm Output Output Adjust Logout View 1 O View 4 Ld View 8 View 9 2 View 16 Spot Shortcut menu in full analog DVR Copyright QVIS All documentation rights reserved 15 12 Recording Config EI To set the recording parameters in the surveillance channel you can enter Main Menu gt Record gt Record Config to set The system s default set to 24 hours continuous recording Note There is at least one read write hard disk if the DVR records normally Main Mcnu gt Rccord gt Rccord Config Channel Redundans Lene TE min Prekecord LIT Record Mode Schedule Manual Stop Detect arm Recording Contig Channel Choose the corresponding channel number to set the channel Choose the All option to set every channel Redundancy Check this option when you have a second HDD drive to use as a backup redundancy option in case the primary HDD runs out of free space whilst recording First HDD is a read write disk the second is a redundant disc ready as a spare Length Set the time length of each video file 60 minutes is default length Prerecord Record 1 30 seconds before the action file length is
55. ssage Automatically alarm cue dialog box come out of the main screen Buzzer Device will have one long nosie di while alarm is happening Copyright QVIS All documentation rights reserved 29 17 4 Intelligent Analysis This options menu will allow you to setup specified picketed areas within the footage frame so that when an object has been analysed entering the picketed area the alarms will be triggered TAMain Menu gt Alarm gt intelligent Analysis x Channel 1 Enable Algor Perimeter Rule Period ese interval M Sec Alarm Output L1 Delay i10 Sec Record Channel RE FI KI 3 E E ED TS UR LE IS s de uio Tour E ERE EGEEBET PTZ Activation 1 Delay 10 Sec Show Message Send Email L Buzzer m FTP upload Intelligent Video Analysis Intelligent analysis function you can set in two rules picket line and picket area You can only use the Video Analysis function on Record Channel 1 no other channels can be used Copyright QVIS All documentation rights reserved 30 1 channel with Channel No Only shows 1 at present only the maximum resolution of 1080P Enable tick this to enable the video analysis function then can go for further setting Algorithm rule at drop down box to choose the algorithm rule of detection Rule choose different algorithm rules the related setting page is different Cordon e Show traces tick it
56. up Copyright QVIS All documentation rights reserved 19 14 Snapshot Storage This option allows you setup the system to take still snap shots from monitor image and save on the allocated HDD Parameter setting Main menu gt Record gt Snapshot to select related setting see pic 3 the function is closed in default Note To instruct system to save snapshots on the primary HDD set Snap at Main Menu gt Advanced gt HDD Manage gt Snapshot W Main Menu gt Record gt SnapShot Storage Record Schedule Manual Stop Week mm WM Regular Detect Alarm Period 1 00 00 Period 2 00 00 Period 3 00 00 Period 4 00 00 Pic 3 Snapshot PreSnap Set how many seconds of pre recorded footage stored in the memory is added on to the beginning of the snapshot You can refer to 6 Record Config section for a very similar description on how to setup the Snapshot options Copyright QVIS All documentation rights reserved 20 15 Playback There are two methods for you to play the video files stored on the hard disk 1 In the desktop shortcut menu 2 Main Menu gt Record gt Playback When you enter the playback interface you can playback video from a multiple of channels at the same time Note The hard disk that saves the video files must be set as read write 277 w 40 07 24 14 28 20 110 0 7 24 14 29 49 BN E 5 70500002900 Pic 4 Playback
57. ute The Configuration of Channel Eacoding Chaneel titles Time title Regional UCoverag y ideo Cobor Restore to default Copyright QVIS All documentation rights reserved 66 19 9 6 Upgrade Main Menu gt Advanced gt Upgrade N Upgrade Position USB DISK Upgrade file Upgrade Upgrade choose USB interface Upgrade file choose the upgrade file 19 9 7 Device Info This provides the device interface info like audio in alarm in out so that it can be conveniently used by the user a Main Menu gt Advanced gt Device Info Audio In Channels Alarm In Channels Alarm Out Channels GUI Theme General Remote control type General Maximum Playback large 4 Default playback large Enable RS232 Enable PTZ Device info Copyright QVIS All documentation rights reserved 67 19 9 8 Import Export Users can export the log info and the configure file from device to connected flash stick and also they can import related configure file from flash stick to settings which greatly bring convenience to the customers Main Menu gt Advanced gt import Export a x Device Name a6 CO File Name 4 File File Import Export interface Copyright QVIS All documentation rights reserved 68 19 10 Info This menu section will display information about the hard disk including HDD info code stream statistic log info an
58. video surveillance through this advanced design Main Features e Real time surveillance Spot interface Analog interface and HDMI video display ports e Storage Redundant hard disk dormancy management to relieve system from high levels of heat Reduces power consumption and extends device life span Special storage format which ensures data safety e Compression H 264 Real time compression by each individual hard disk which ensures that the audio and video signals have stable synchronisation Copyright QVIS All documentation rights reserved 2 e Backup nbuilt SATA and USB interface for an external storage device through net download the files in the hard disk e Playback Individual real time video recording as well as searching playback network surveillance recording checking downloading and more Mutti tile playback mode Zoom into arbitrary regions e Remote Network Operation Ethernet connection for real time surveillance across a structured network Remote PTZ control Monitor recorded footage and real time playback e Alarm linkage Alarm activated video recording tour message buzzer e mail and F TP e Communication interface 5485 interface provides a connection for the alarm input and PTZ control Copyright QVIS All documentation rights reserved 3 5232 interface provides an extended keyboard connection to work in conjunction with the master keyboard

User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents