Norsk, svenska and english user manual
Contents
1. iT E mr 4m osstkeuy A FT Tr rra Evinrude E tec p x Revision 2 6 English version Not included the ICON model f Fan Dr E RESSBEILT BL j bi 2 INSTALLATION GUIDE Evinrude E tec installasjonsguide CoastKey harness connector CoastKey harness Checklist before installation Read the installation guide and user manual before installing the CoastKey system Check that the engine s functions and operates normally before installation The CoastKey system shall not be installed in an explosive environment The CoastKey system and design may not be changed or tampered with The system should only be used for its original purpose and only installed as per the directions in this Installation Guide Familiarise yourself with the national safety rules and regulations in your region to avoid a breach of these rules and help prevent accidents The installation of the lock unit is permitted only in areas that are protected against water intrusion The lock unit shall be installed on a fiberglass wood plastic glass or other non conductive surface The lock unit must not be attached to carbon cables wire or other metal surfaces as this leads to loss of signal strength which will affect radio communication between the key and lock unit Strong electromagnetic fields may also affect the system Locating the lock unit in t2. because the original manual lanyard cord attached to the key switch will stop operating when the black wire with yellow stripe is disconnected from the key switch INSTALLATION GUIDE Evinrude E tec Note Be careful when drilling holes to not damage other equipment Check the inside of the console for objects that might get hit by the drill bit The engine can be started from the original key switch if the lock unit is disconnected In this case the engine must be stopped with the manual lanyard cord provided with the kit as long as the black wire with yellow stripe is disconnected from the ignition key switch 4 The lock unit Clean the surface where the lock unit is to be placed with acetone or similar and place it according to the guideline in Installation checklist located on page 2 Plug the lock unit into CoastKey s harness 5 Test and Safety Secure CoastKey s harness and other loose wires with cable ties Turn on the main switch and complete the Test and Safety Form on the next page before you use the boat for the first time Note If the boat is equipped with two engines repeat the above installation procedure for engine No 2 Checklist for Installation Test and Safety Form Checklist for Installation Please refer to user manual for proper procedure for carrying out the points below Turn on the ignition and start the engine s with the key fob Check that the start sequence w
3. at the engine s tilt and any other devices that CoastKey will be connected to are functioning normally before starting the installation The main switch must be switched off during the installation 2 Key switch and connections Modify the key switch and it s connections according to the description below Disconnect the yellow wire with red stripe from the post on the rear side of the ignition lock you might need to pull back the rubber boot to be able to loosen the connector Connect the female plug on the black T split harness provided with the kit to the same post The male connector on the T split is then connected to the yellow and red wire that was removed from the ignition lock This ensures that your start in gear protection isn t compromised see Figure 1 Figure 1 NSTALLATION GUIDE evinrude E tec A side mounted remote control must be opened to access the ignition switch to perform the installation The black T split harness used to connect the start signal is routed out of the remote control along the control cables for gear and throttle The black T split harness single end is connected to the brown wire in CoastKey s main harness Remove the black wire with yellow stripe from the ignition switch see Figure 2 You might need to pull back the rubber boot to be able to loosen the connector This wire will stay disconnected Pull the rubber boot back on to the connector to avoid any possibility of a short circu
4. he immediate vicinity of conductive cables and any radio devices such as VHF radar etc should also be avoided To achieve optimal radio and signal conditions it is recommended to install the lock unit as high as possible in the boat at least 70 cm above the waterline Ensure that the lock unit is secure and stable so it is easy to operate the push button Clean the attachment point with acetone or a similar cleaning fluid before the supplied Velcro strip is attached Other wireless systems that use the same frequency In Europe 433 MHz such as a remote controlled anchor winch or bow thruster can affect the operational stability of the CoastKey system The distance between the installation point of the lock unit and the pilot s usual position should be as short as possible and not exceed a radius of 1 5 meters Ina dual installation the lock units should be placed at least 30 cm apart For security reasons the power supply to the lock unit s is to be connected through a main power switch Maximum system load is 10 amps Check current draw when connecting to external systems like anchor winch etc Remember to complete the Test and Safety Form in this guide Revision 2 6 English version INSTALLATION GUIDE Installation procedure 1 General Make sure the battery terminals the main power switch and all common connec tion points are free of corrosion and that there are no loose connections Check th
5. it On a top mounted or panel mounted remote control application the ignition switch is installed in the console In this case there is no need to open the remote control to perform the installation A gray 6 pin connector is located 20 30 cm 8 12 down the main harness from the ignition switch remote control This is the main con nector between the ignition switch and the main harness from the en gine This connector is disconnected a and the corresponding connectors on CoastKey s harness are inserted between the original connectors So that they form a T connection See figure 3 Revision 2 6 English version INSTALLATION GUIDE The same procedure is done with the triangular gray 3 pin connector for the tilt signals On a side mounted remote control you ll find this connector in the same area as the main connector On a top mounted remote control you ll find this connector on the signal cables from the control handle Note Exercise care when opening the side mounted remote control The throttle and shift cables might be in tension and accidentally pop out making it difficult to re assemble the remote control 3 Lanyard Switch Figure 4 Drill a 16mm 5 87 hole for the engine kill switch provided with the kit Install it in a suitable place in the console See Figure 4 Connect the kill switch s wires to the black and blue wire on Coast Key s harness See Figure 5 The kill switch is provided with the kit
6. orks correctly and as specified Check the radio range by moving the key device more than 20 meters away from the boat to make sure that the wireless lanyard cord is functioning prop erly and stops the engine s The distance needed to stop the engine s on land can vary based on the radio reflection where the boat is located Check that the key device vibrates and the signal beacon is activated when a Man overboard situation is simulated The ignition is switched back on automatically 12 seconds after a man over board situation has occurred Check that the engine s can be started directly from the lock unit s push button after a simulated man overboard situation Reset the system by taking control via the key fob by turning it off and then back on by switching the main switch off and back on before the next test Enter the 4 digit PIN code provided with your CoastKey system by pressing the lock unit s button to unlock the system and check that the engine s starts after the confirmation tone Optional Check that the aux functions work from the key unit If connected to trim in a dual installation check that both engines tilt in parallel If connected to an anchor winch the anchor must be secured with a strap Make sure the winch pulls in when you unlock the key lock on the key fob Check that the manual ignition switch works normally when the lock unit is disconnected The lock unit is disconnected by disconnecting the g
7. ray 8 pin connector located 15 cm down the lock unit s harness When the system is disconnected there are some types of engines that can only be stopped using the manual lanyard switch The User Manual must be read before the CoastKey system is used Drivers and passengers must be informed of the lock units position and how to restart the engine s inan emergency Take care of your owner s manual as a future reference Disclaimer CoastKey AS will not be held responsible for any damage to personnel or property arising from the incorrect use or installation of any CoastKey product It is mandatory to read the installation manual user manual and complete the test and security form before attempting any CoastKey installation CoastKey AS Vestre Strandvei 77 N 3482 Tofte Norway t www coastkey com post coastkey com sl I
Download Pdf Manuals
Related Search