User Manual - Handy Dryers
Contents
1. foreign objects El Motor fault nomally than 25s restart to work Timing digital ES Incorrect voltage power tube surge Voltage drop Check the power supply circuit Machine temperature Master board tempera Ensure the air inlet and outlet are higher than 80 C ture is higher than 80 C clear of foreign objects Fan fault Check the fan sensor connection There are locations unsuitable for this unit DO NOT install in the following types of location e Where the temperature can be below 10 C or above 40 C e Where the unit may come into direct contact with water e If the unit will be in direct or strong sunlight e If there is a lot of condensation in the environment e If there are corrosive neutral or reductive gases present e 20m or more below or 2000m or higher than sea level Installation location considerations e Install the unit in a position where the unit will be easy to use Note that if the unit is installed too low it may get wet when the floor is cleaned e Ensure there is at least 150mm clear space below the machine either to the floor or other objects in the location e It is recommended that a minimum distance of100mm should be left clear to either side of the unit e Avoid locations where people or doors might damage the unit e Choose a completely flat wall surface to mount the unit to Spur location e Connect directly to fused spur ensuring spur is at least 300mm away from the mach2. the unit away from direct water supplies A suitably rated fused power supply is required Ensure the correct power supply is used if more than 10 the unit may malfunction The power must be turned off during maintenance The drain tank and air filter must be installed for correct operation Ensure the unit has a reliable earth connection Do not install connected to a power supply This hand dryer must be installed by a qualified electrician If the power cord is damaged it must be replaced by the manufacturer its service agent or a qualified person A residual current device RCD with a rated residual operating current not exceeding 30mA is recommended ENVIRONMENTAL PROTECTION Do not dispose of electrical waste with household waste please recycle in appropriate facilities Check with your Local Authority or retailer for recycling advice Drying time Power Filter sterilisation Heater button and fault display indicator indicator Power supply Fan speed button Self check indicator Manual power switch Sensor Hand drying area Unit Ao Drain hose Switch door plate Drain outlet Bottom Air inlet panel Full level indicator Drainage tank DE 9C Lock Air inlet Air filter Hook 4 85 S 215 300 Terminal box location OS r e e O
3. LTER Before it fills up at least once a week About once a week e To prevent water from overflowing it is Remove the air filter necessary to regularly empty the drain tank e Open the air inlet panel e f the accumulated water is left in the drain tank Pull the air filter out by it may degrade and start to smell the handle Gently pull the drain tank out in a horizontal direction Full level E 1 Cleaning the air filter Ee e Beat it lightly by hand or use a vacuum cleaner 1 Open the cover and empty e You can also use a soft 2 Wash and disinfect the inside of the drain tank brush to brush off the du 0 3 Replace the cover and return to the unit 2 Re attach insert the correct way around into the unit and secure the 4 N door shut and lock Drain tank Add 200cc about 1 cup of clean water through the drain hole and clean with supplied brush to prevent clogging with debris NOTE DO NOT use water to clean the air filter Drain hole TROUBLE SHOOTING No air blows even Are the display indicators lit Turn the ground fault circuit breaker on if hands are inserted Is the power switched on Turn the power switch on Are you putting your hands all the way into Put hands all the way into the unit the unit Machine continues working Is there any dirt or foreign body on the sensor Swith off the power button and once the power light has gone off when hands are removed remove the dirt or fore
4. O O 2 o LO o e e 29 278 170 Stretch out both hands and insert them into the unit The drying function will start automatically Pull them back slowly allowing the water to blow away Repeat if necessary dil Pull hands out completely Y Y WALL STICKER Place wall sticker in a prominent position the front of the unit or a wall nearby gorillo ULTRA MEL handydryers www handydryers co uk CLEANING YOUR GORILLO ULTRA Before it gets obviously dirty WARNING e Before cleaning the unit ensure power is e Clean with a soft cloth If the unit is very dirty use ev sies oft a soft dampened cloth with neutral cleaning agent Sy e DO NOT splash excessive water into the unit then polish with a soft dry cloth CAUTION e Wear gloves when cleaning e The antibacterial coating is effective when bacteria is exposed to the surface e The antibacterial coating will become ineffective if the surface Disinfectant alcohol below 83 concentration is very dirty e Remove dirt from the sensor to prevent malfunction Only use neutral cleaning agents Do not use thinners acidic or alkaline toilet cleaners or nylon brushes they may damage the surface Use alcohol to clean the hand drying area but DO NOT use alcohol anywhere else on the unit If using chemical cloths please read instructions first Disinfecting agents will damage the unit DRAIN TANK MAINTENANCE CLEANING THE AIR FI
5. e lid ii Unscrew the 2 screws on the pressure line cover loosen the 3 screws on terminal box then pull out the power line Terminal box Pressure line Electric cover Power cords Replace the terminal block cover e Ensure power cables sit within the cabling channel and the terminal block cover is flat after installation Fix the unit e Tidy the power lines and press any excess into the terminal block on the wall e Hang on metal wall brackets and ensure it sits flush to the wall e Install the safety screws x 2 NOTE the unit must be installed with the safety screws or it will be unstable 1 Replace the air filter e Carefully push the air filter up into the unit close the air inlet door and lock it with the catch 2 Replace the drain tank e Push the drain tank into the unit as shown Installation panel Terminal box Pressure line Mounting plate arsar agt cise KEER RES carr EE A E a Ewe EE 1 5mm Expansion pipe 6 5 X 30 Self tapping STTEWS ssa a ested a eo woe Welder eas a ee ada 6 User manual including Packing List and Warranty Card 20 000 c cee eens 1 Method of USE ies OE EE vas ves See ewe Eee ee des Pee Des Mee eee pew eee ee 1 Drilling template ss EE of Seco bee eG AE DE as gine IT Ie ac le OG inte ae akan 1 orillo Ta 9 ULTRA WK handydryers www handydryers co uk
6. gorillo 1 User Manual handydryers Do not attempt to install the unit yourself unless you are a trained service technician or this may affect the safety and functioning of the machine Read this manual thoroughly before using the unit and retain for future reference CONTENTS Gontents 8 Specifications sessa a Ree ena a Rd RA ee Re eae WEE Ee Ee 1 ae le AA EE EE RE EE rra dar si ened 2 Component Names amp Unit Dimensions EE EE eee 3 IE EE OE EO RE EE a EE EE EE EE OE ii 4 Clearing ii TE A A A OO TR E AA EE A IE A A 5 Trouble Shooting Electrical Schematic iss Es isois EE eee ER ER a E ER ek ke i 6 Pre installation Precautions iss sie se RE EER E wa a eee ME EEN WEE RE RR eee ER ER RE EE RR Oe ea RR Ee 7 InstallatiO AAR TO ET OE EE ap os RE OE N ORR OE ae 8 Ed RE EE EE OE EE OR EE A A ER EO A EO 9 PackiMgiliSt NL ai m a ER OE EE FO OO EE EE EE OT N OE ER 10 SELF PROTECTION This machine has inbuilt self protection which means it will automatically stop working after 25 seconds To continue drying withdraw hands and re insert them SPECIFICATIONS Heating power 1000 1200W o ls Prohibited Do not allow unit to get excessively wet Follow instructions carefully O Ensure unit is earthed Do not dismantle a Injury may occur if misused DO NOT OPEN THE FRONT PANEL ELECTRIC SHOCK RISK DO NOT ALLOW CHILDREN OR ADULTS TO PULL OR HANG ON THE MACHINE Place
7. ign body from the sensor Once finished screen shows E2 switch the power back on No hot air There is an inbuilt heat sensor in the unit is Is the ambient temperature higher than 20 C there any dirt on the heating sensor Switch off the power remove the front cover There is a terminal Has the fuse inside the terminal box blown box inside take the cover off this Check whether the fuse inside the terminal box has blown Airflow is too low Is the speed button set to low level Turn the speed button to the high setting If the above actions do not work turn off the power and call your dealer to inspect and repair your unit if necessary ELECTRICAL SCHEMATIC Temperature Thermal protection probe switch Thermal circuit breakers Power switch Heaters Wiring Fees eed terminal A blocks Compensation Temperature EE PCB probe probe Sensors Emus EI Sensors receiving PCB 1 5 12 Start PCB Power Check external power source close Power not supplied the power switch Power Power on indicator light Master board fuse blown Repair fuse A Motor fault it won t Check motor connecting wires and Machine not in use gt State indicator operate nomally the clear any foreign objects light Flashing light 19 Used for longer Clear workspace of foreign objects than 25s restart to work Digital Readout Run time longer Clear workspace of
8. ine never directly above or below the unit Fixed screws Installation panel Safety screws Recommended 890mm for gents 0 870mm for ladies Drain tank ON Power switch installation heights E Enj K Distance between the terminal box without cover and ground Installation panel Terminal box Air filter Use a single phase alternating rated voltage supply Not to be used with a power supply exceeding 10 Use a power cord between 2mm and 2 5mm thick A voltage drop is possible if longer than 11m so we recommend using 2 5mm cable Wire the unit Embed a backbox in the installation location 1 switchbox no cover e If no backbox is used the power cord may prevent the unit from sitting flush against the wall If the wall is concrete use metal screw plugs raw plugs etc If the wall is not concrete reinforce it prior to installation Place the drilling template onto the wall and drill holes Place rawplugs into the holes and screw on mounting plate as shown he Remove the drain tank and air filter Drain tank Air filter Power cord Installation panel Installation Drilling Sorews get template E N f E 3 3 Switchbox id Q o Security 5 screw holes 2 Remove electric cover and power cords i Unscrew the 2 screws on the electric cover and remov
Download Pdf Manuals
Related Search