Dishwasher Service Manual Type: Wp5C/5D Fully
Contents
1. different temperatures are available and can be observed from the thermostat The circuit is opened below this temperature and closed above it Removal and replacement Remove the outer casing and bottom pan Remove the connecting wires behind the sump and check with an ohmmeter whether the thermostat circuit is opened in normal temperature and closed when temperature rises above 67 If the result if positive the thermostat is normal Otherwise it fails and shall be replaced Remove the screws and the mounting plate Replace a new thermostat and the mounting plate The mounting plate shall press tight to prevent water leakage at the thermostat end Replace the connecting wires bottom pan and outer casing The dispenser 106 releases automatically the brightness liquid into the machine at the final rinsing stage The brightness liquid reduces the surface tension of the water and eliminates dirty spots from the dish surface The dispenser can hold brightness liquid for one month use At the final rinsing stage the electrical controller activates the electromagnetic valve of the dispenser and pulls the rubber gasket of the valve core to release a suitable amount of brightness liquid which is carried away in the flowing water Removal and replacement Check and replace the dispenser a Turn the power switch to OFF and pull out the power cord Guard against sharp edge from cutting the power cord b Open the door remove the four2. f Check the connecting tubes and replaced the damaged ones NNN Removal of Drainage Troubles a Check the drain hose for twist air bubble or blockage and make necessary correction b Check whether the motor is burnt If so replace the drain pump as specified above XIV Overheat Thermostat This thermostat is designed to prevent overheating of the heating element The temperature limitation is set at 115 Below this limitation the circuit is closed Once the temperature rises above this limitation the circuit is cut protecting the heating element from being burnt Removal and replacement Remove the outer casing Remove the thermostat connecting wire and check with an ohmmeter whether the thermostat circuit is closed in normal temperature and opened when temperature rises above 120 If the result if positive the thermostat is normal Otherwise it fails and shall be replaced From the lower left side you can see the thermostat at the end of the sump Remove the nuts on the thermostat mounting plate Remove the mounting plate and the thermostat Replace a new thermostat and add some heat conducting silicone grease to its end Wrench tight the nuts on the thermostat mounting plate and connect the thermostat connecting wires Replace the outer casing XV Water Temperature Thermostat This thermostat 47 is designed to inspect the water temperature and control the heating element The temperature control point is set at 55
3. controls the water volume into the dishwasher The electromagnetic valve is fixed on the valve base When it is powered a magnetic field will come and pull the valve core to let in the water The feeding of the water depends on the electrical controller which controls the opening of the electromagnetic valve In normal circumstance the pressure in the inner container of the dishwasher shall be 78 85mm above the sump bottom Open the door to check the pressure when water is filled During the washing operation the inlet valve may open to add some water Removal and replacement Check and replace the inlet valve a Turn the power of the dishwasher to OFF and pull out the power cord plug guard against sharp edge from hurting the power cord b Check with an ohmmeter as instructed c Remove the outer casing and the rear panel d Check the connecting wire of the inlet valve for looseness and the valve for crevice e Check the connection of the inlet hose f If the incoming pressure in the water tank is lower than the normal level remove the inlet hose clean or if necessary replace the filter screen and reconnect the inlet hose g Check the inlet valve terminals with an ohmmeter The probes should touch the terminals of the inlet valve If the pointer does not move replace the inlet valve with a new one h When replacing the inlet valve turn down the water tap and remove the clamp and the connecting tube j Unscrew
4. screws in the sides of the inner door unscrew the knob cap of the dispenser and the two locknuts and remove the inner door c Check the dispenser for any leakage or release of brightness liquid If no brightness liquid is released check if there is brightness liquid in the dispenser If there is brightness liquid in the dispenser check the terminals connected to the dispenser for looseness and fallout d Pull out the two terminals of the connecting wire connected to the dispenser and remove the dispenser e Check the electromagnetic valve of the dispenser with an ohmmeter If the dispenser is broken replace it f Connect the terminals of the connecting wire of the dispenser and replace the inner door g Wrench tight the two locknuts and knob cap of the dispenser and check the dispenser for tightness XVI Spray Arm Assembly If the spray arm assembly is blocked unscrew the nut beneath the spray arm and remove the spray arm to wash out the obstacles Note the spray arm nut is turned to the left When removing the obstacles do not dig or pry the spray arm and nozzle Otherwise the washing effect and the service life of the spray arm may be compromised XX Explosion Diagram and Schedule the annex 1 XXI Circuit Diagram rp WATER VALVE GR pa RINSE AID W gt ONLY R _ DETERGENT DISPENSER Q ag FOR SPECIAL tm SOFTENER VALVE VIO pe TYPE J g R T WASHING PUMP p m m i IR DRAIN PUMP BR Ph N R THERMOSTAT
5. shorted Replace motor washing but not Defective electric control Replace electric control stop Water siphons out See water siphons out The sump or the filter was Clear the sump and filter obstructed Soap suds leak from Refer to owners manual The fuse for the clei ler Too less fill water See too les fill water heating element break Defective thermostat Replace thermostat Damaged or defective wiring Repair wiring Defective micro switch Replace the micro switch Defective or too dirty the inner of the bobber base Replace or clear the bobber base Defective electric control Replace electric control Drain hose loop too low Move drain hose to proper height Water siphons out Drain hose connected to a Install a vent air gap at floor drain not properly counter top vented Etchi Soft water condition Natural Have a sample of water ching on ie or artificial analyzed by the local water glassware department Detergent allowed to stand Instruct the customer on too long in the dispenser or proper use of dishwasher excessive amounts of detergent Refer to the Spotting or filming detergent are being used owner s manual on Improper loading of dishes glasses reposition pots pans and nesting of of food soil silverware Improper installation of the Install properly Refer to dishwasher to a food waste installation manual dispos
6. various operations of the dishwasher automatically The output cords of the electrical controller are in different colors With the circuit diagram in hand you can track the circuit from the electrical controller to any element The electrical controller is a very reliable unit In case of dishwasher troubles check other causes first before focusing on and replacing the electrical controller Such as the power switch it is a push button switch 3 Press the power switch and check with an ohmmeter whether the normally open terminal is closed If it is not closed replace the switch 4 Remove the control panel unscrew the screws to remove the defect switch and replace with a new one 5 Connect the wires behind the switch and check if they are connected fast X Protection Pressure Switch and Working Pressure Switch Removal and replacement adjusting screw common terminal normally open terminal Micro switch Micro switch protection ex de Va Mounting screw ce fastening screw P d S EE e The inlet water flux of the dishwasher is implemented by a float pressure switch which composed of two micro switches The up switch is the working level 95 The smaller current 7A controls the protection level 93 The working level is set at 78 85mm above the sump bottom and the protection level is 5mm or more below the brink of the inner container The check and adjustment of the pressure swi
7. 19 Front Left Bracing Bar 1 20 Spray Arm Assembly 1 21 Spray Arm Nut 1 22 Spray Arm Support Locknut 1 28 Spray Arm Base Nut 1 24 Spray Arm Base Gasket 1 25 Remove Residue filter net 1 26 Filter residue net 1 27 filter 1 28 Front Cover Facing Bar 1 29 Door Spring 1 30 Door Hook 1 31 Inner Door 1 32 Door Left Hinge 1 33 Pulley 2 34 Door gasket 1 35 Door Bracing Bar 1 36 Outer Door 1 37 Door Foam 1 38 Door Airproof 1 39 Pulley Axis 2 40 Door Right Hinge 1 41 Heating Element Thermostat 1 Mounting Plate 42 Thermostat 2 36TM01 L115 15C 1 43 Heating Element Mounting Plate 1 44 Heating Element Gasket 1 45 Heating Element 230V 1200W 1 46 Sump Gasket 1 47 Thermostat 1 36TX12 F55 12C 1 48 Thermostat Gasket 1 49 Sump 1 50 Front Cover 1 51 Foot 4 52 Bottom Pan 1 53 Switch Button 1 54 Press spring 1 55 Control panel 1 56 Model selected button 2 57 Model button spring 2 58 LCD screen 2 59 Power Cord HO5VV F 3G1 0 mm 1 60 Panel holder 1 61 Door clock button 1 62 Press spring 1 63 Control PCB 1 64 Power switch 1 65 Transformer 1 66 Holder foot for electronic control 2 67 1 0 PCB 1 68 Holder Clamp 4 69 Swing level 1 70 Swing level hinge 1 71 Bober holder 1 72 Bobber base 1 73 Micro switch protection G3MITIPUL 7A 250V 1 74 Bobber Cover 1 75 Micro switch X302K 12A 125V 1 76 B
8. Dishwasher Service Manual Type Wp5C 5D Fully Automatic Double Pump Commonly Used Tools For the sake of safe and efficient manipulation you should prepare and learn to use the following tools prior to servicing the dishwater Plus screwdriver Minus screwdriver H screwdriver Torque spanner OTK caliper and universal meter Attention never measure the resistance of live cord Otherwise you measuring device may be damaged The trouble shooting CHECK FOR THE SYMPTOM FOLLOWING REEDY The water supply is turned off Turn the water supply on The pipe was snapped Put the pipe in the right way Low water pressure Minimum water pressure of 0 04Mpa Defective water fill valve Replace the water fill valve Obstructed water fill valve or Disassemble and clean the E1 hose water fill valve and hose Damaged or defective wiring Repair the wiring Defective micro switch Replace the micro switch Defective or too dirty the inner Replace or clear the bobber of the bobber base base Heavy water usage Use dishwasher when elsewhere in home water usage is at a minimum Defective the electric control Replace the electric control Damaged or defective drain Replace the drain pump pump Drain hose was obstructed or Put the hose in the right way snapped EZ Defective micro switch Replace the micro switch Too dirty the inner of the Replace or clear the bobber bobber base b
9. HEATER BK HTT du E pi n T gt 115 C BR s VIO us R P2 NIB DOOR SWITCH NN POWER L SWITCH w IH lt B c l 70 D ON w lt w C L d PU PURPLE zw We BR BROWN XW J30B 1 PCB CN3B NNNNNNNN NNNNNNNN CN2B SPSS LS ASL LSS hf uv SJ SLL SSS d XWJ30B 2 PCB TRANSFORMER p lt gt WORK GR LEVEL p lt gt OVERFLOW 0 LEVEL T gt BU THERMOSTAT BR REED R xu SWITCH ONLY FOR SPECIAL TYPE COLOUR CODE BU GR 0 BLUE GRAYER ORANGE R Y W BK Y 6 RED YELLOW WHITE BLACK YELLOW GREEN XXII Consumables List No Part Name Specification QTY 1 Outer Casing 6 0 6mm 1 2 Insulation piece 1 3 Micro switch X3M302K2KA 1 4 Door Lock Screw 2 5 Door Lock Base 1 6 Door Lock Spring 2 1 7 Spring Washer 1 8 Door Lock draw rod 1 9 Door Lock Spring l 1 10 Slider 1 11 Door Lock Holder 1 12 Top Rubber Plate 1 13 Inner Container Assembly 1 14 Rear Left Bracing Bar 1 15 Condenser 1 16 Condenser Gasket 1 17 Condenser Nut 1 18 Door Gasket 2 1
10. al Noisy pump Debris in bottom of tub sump Clean out the sump area assembly area Pump parts were not properly installed Inspect the pump and correct and installation errors Impellers are not properly shimmed or are rubbing Use the shim guage furnished in the impeller seal kit When the seal is properly shimmed the impellers will be in the correct operating position Poor clearing The sump or the filter was obstructed Clear the sump and filter The filter is not in position Put filter and micro filter in position The filter was distortioned Repair or replace filter Dishes or knife fork or something else stifled spray arm Rotating the spray arm before start Improper loading of dishes pots etc Too less of the detergent The wrong wash program be chosen Instruct the customer on proper loading of the dishes refer to the owners manual Defective module detergent rinse Replace the detergent rinse Defective spray arm Clear or replace the spray arm Too few of the inlet water Check as the ERROR 2 Defective pump Replace the pump No salt in the softener Add salt to the softener Poor drying Improper loading of dishes pots etc The wrong wash program be chosen Instruct the customer on proper loading of the dishes refer to the owners manual Defective detergent rinse Replace the detergent rinse
11. ase Damaged or defective wiring Repair the wiring Defective the electric control Replace the electric control E3 The voltage too low Minimum voltage of 198V Damaged the thermostat 2 or the fuse for the heating element Replace the thermostat 2 or the fuse Damaged or defective wiring Repair the wiring Damaged thermostat 1 Replace the thermostat 1 Damaged the heating Replace the heating element element Defective the electric Replace the electric controller controller Defective micro switch Replace the micro switch E4 Damaged or defective wiring Repair the wiring Defective the electric control Replace the electric control Damaged water valve Replace the valve Defective micro switch Replace the micro switch E5 Defective or too dirty the inner Replace or clear the bobber of the bobber base base Damaged or defective wiring Repair the wiring Defective the electric control Replace the electric control Salt leakage for equipped with softener The cover of the softener be loosed Tighten the cover The o ring of the cover be inversed Replace the cover Not operate after push start key Door was not closed Close door Damaged or defective door switch Replace door swich Damaged or defective door lock Replace door lock Damaged or defective wiring Repair wiring Defective electric control Repla
12. ce electric control The control interference to Repair the panel or control panel Defective water fill valve Replace water fill valve Fill water not stop Debris buildup under Clean out debris or replace even no power diaphragm in the water fill valve water fill valve Fill water not stop but stop if no power Defective electric control Replace electric control Too less fill water Low water pressure Minimum water pressure of 0 03Mpa The pipe was snapped Put the pipe in the right way The sump or the filter was obstructed Clear the sump and filter Defective micro switch Replace micro switch Dishwasher not level Level the dishwasher Dishwasher runs with door open Damaged or defective door switch Replace door swich Damaged or defective door lock Replace door lock Damaged or defective wiring Repair wiring Defective electric control Replace electric control Motor hums but not start or run Defective motor bearings Replace motor Defective motor capacitor Replace motor capacitor Damaged or defective wiring Repair wiring Improper motor voltage Replace motor Motor trips out on internal thermal overload protector Improper motor voltage Replace motor Motor shaft binding Replace motor Defective motor capacitor Replace motor capacitor Motor windings
13. d take away the rear panel Lift up and away the outer casing from the dishwasher check and repair the internal parts 7 Remove the six screws from the control panel holder 60 see fig 3 below and the two stainless steel screws in the inner container see fig 1 below and pull out the control panel 8 Turn the dishwasher upside down remove all the screws in the bottom pan open the cord clamp and remove the bottom pan DaD P Ss y S LE tS VII Check Internal Connecting Wire The internal connecting wire connects the I O PCB 67 the power switch 64 the inlet valve 99 the heating elements 45 and other electric elements together The wires shall be kept intact Any damage to the wire may cause overheat and result in broken wire Common troubles to the internal connecting wire are broken wire bad connection terminal contact and connection terminal insulation layer damages To repair the dishwasher the ground shall be connected When an electric component is replaced check whether the ground is connected again This is a crucial step to avoid electric shock and short circuit Attention To replace electric cord use the cord of the same temperature resistance and specifications The specifications and temperature rise are marked on the cord Removal and replacement 1 Disconnect the power prior to check 2 Open the outer casing and if necessary remove the bottom panel 3 Check the wires and conn
14. e damaged ones Removal of Drainage Troubles a Check the drain hose air bubble or blockage and make necessary correction b Check the drain pump If damaged replace the drain pump as specified above XIII Heating Element and Protective Thermostat The heating element is located in the sump When it is powered in the heated washing cycle it warms up the water which will clean the dishes more effectively and generates heat after washing to dry the dishes The heating element has a nichrome filament inside You can measure the resistance with a universal meter to check its condition The protective thermostat is a temperature limitation switch and a safety device In case the dishwasher fails and the temperature inside the inner container rises above a specific limitation the thermostat will cut the heating element circuit to avoid any damage to the machine Removal and replacement Remove the outer casing From the left side you can see the heating element assembly installed to the end of the sump Pull out the connecting terminal of the heating element Check the heating element with an ohmmeter for damage and replace the damaged one Remove the connecting nut and the thermostat Remove the end cap of the heating element and take the heating element out of the sump Replace a new heating element and install the assembly as usual Note install the thermostat end with heat conducting silicone grease tighten the heating elemen
15. ectors and replace the damaged ones VIII Door Lock Assembly Slider micro switch Micro switchspring The working mechanism of the door Pi lock is that the linkage 8 bolts up the cy y door hook which in its turn presses ae S Linkage the micro switch spring in the lock ls Ea assembly to form a closed circuit The T S lock mechanism consists of the door y lock holder 11 the slider 10 and the SS S micro switch 3 When the door is opened the door hook is withdrawn to release the micro switch cutting the power supply for open door protection In case of worn out slider micro switch failure or deformed micro switch spring troubles may occur and the dishwasher will stop to work as usual Removal and replacement 1 Pull out the power cord plug prior to servicing the door lock mechanism 2 Remove the outer casing 3 If micro switch failure disconnect the micro switch remove the two screws and replace a new micro switch 4 f deformed micro switch spring adjust the spring with a nipper pliers so that the micro switch returns to its original position when the slider is released and the micro switch closes when the slider is pressed tight or replace the micro switch IX Electrical controller The power switch Removal and replacement 1 Pull out the power cord plug 2 Remove the outer casing The electrical controller of the dishwasher consists of a control PCB and I O PCB it controls the
16. module The temperature too low Replace the NTC thermistor during rinse wash Replace the electric control Note in the narration of this manual the number in brackets behind the part stands for the serial number of the part in the explosion diagram The actual configuration may be different Ill Check of Performance Loading of Dishes Many of the performance failures of the dishwasher are not the result of echanical troubles And the unsatisfactory washing result can usually be corrected without any service This manual deals first with the problems in performance To have satisfactory washing result you have to use the machine correctly First thing first the dishes shall be placed in a correct manner If the machine works well and the washing result is unsatisfactory you should check the layout of the dishes as follows 1 2 Load the dishes as instructed in the user s manual Preparation of the dishes such as dumping the remaining food and removing from the dishes food lumps starches in particular shall be done prior to loading The dishes shall face the water flow from the spray arm for free washing Do not place the dishes in an overlapped way Load heavy pans and large soup bowls downwards If the upper racks are barred from water flows do not place articles on them any more Leave some space in the front of the wire basket so that the water flow may wash out the dishwater detergent from the detergen
17. obber 1 77 Lever 1 78 Capacitor CBB6 1 10 u F 1 Water Level Switch 1 79 t Connecting Hose 80 Motor Base Rubber Pad 4 81 Washing Pump Assembly 1 82 Washing Pump Inlet Hose 1 83 Spray Base Connecting Hose 1 84 Drain Pump Drain Hose 1 85 Drain Pump Inlet Hose 1 86 Drain Pump DP025 475 1 87 Front Right Bracing Bar 1 89 Forel Ring 1 90 Wobbler 1 91 Rear Right Bracing Bar 1 92 Inlet Connector Gasket 2 93 Vapour inlet hose 1 94 Connect cord piece 2 95 Panel to press cord 1 96 Insulation Porcelain 1 97 Inlet Hose connector 1 98 Vapour hose 1 99 Inlet Valve 230V 50Hz 1 100 Panel to install inlet valve 1 101 Rear Panel 1 102 Drain Hose Connector 1 103 Power Cord Pad 1 104 Power Cord HO5VV F 3G1 0 mm 1 105 Rating Label 1 106 Dispenser assembly 1 107 Drain hose 1 108 Inlet hose 1 109 Rack assembly 1 1 fuse SF109E a c 250V 10A 113 C
18. t nut and secure the gasket and end cap The screws shall be wrenched tight No leakage is allowed The connecting terminal shall be upright and the heating element terminal shall be securely connected Connect the power cord and reinstall the machine adjusting screw common Water Pump Motor Assembly The dish washing is a joint accomplishment of the circulation pump 81 and the drain pump 86 The possible troubles of the water pump motor assembly include burnt motor coils starting capacitor 78 damage damaged pump sealing spring broken sealing broken connecting tube etc Removal and replacement a Remove the outer casing and turn the dishwasher upside down b Remove the connecting screws around the bottom pan and the screws to the circulation motor support the drain motor and the pressure switch bracing bar c Check the capacitor and if necessary replace a new one d Check the circulation pump for defects In case of defective pump replace it in the following manner 1 Remove the inlet hose clamp and the circulation pump 2 Replace a new circulation pump 3 Put on a new inlet hose clamp and connect the tubes and wires 4 Tighten the clamp e Check the drain pump for defects In case of defective pump replace it in the following manner 1 Remove the inlet hose clamp and the drain pump 2 Replace a new drain pump 3 Put on a new inlet hose clamp and connect the tubes and wires 4 Tighten the clamp
19. t trough in the inner door On the fork knife rack the tableware shall be placed with handle down evenly Do not load there the articles that may fall out from the bottom IV Check of Performance Detergent and Brightness Liquid The water pressure hardness and temperature and the detergent are the major elements that affect the washing effect of the machine Choose the right detergent and dosage according to the local water condition you will have satisfactory washing result 1 2 3 Use only the fresh and dry detergent of the designated brand Outdated detergent will reduce the washing effect Contact the local water supply company for the water condition if applicable The higher the water hardness is the more detergent shall be used Check the brightness liquid in the dispenser and add without delay if it is insufficient The brightness liquid helps the water to drip making the dishes easy to dry and curbing the formation of water specks on the surface of the dishes V Power cord The power cord of the dishwasher usually has a three pin plug Connect the power supply as instructed in the user s manual If the dishwasher does not work the power cord might be in the fault Most of the power cord troubles arise from damaged cord or loose connection and are visible Attention To avoid electric shock the power socket and power cord shall be well grounded Never use two hole conversion connector that has no gro
20. tch If pressure switch trouble is suspected check whether the dishwasher is level If it is in level position remove the outer casing Add water to the inner container and check whether the float and lever is choked In case of choking correct it If the working pressure switch remains placid when the pressure in the water tank rises over 94mm the switch might be obstructed by the lever or damaged In case of damaged switch replace it If the protection pressure switch remain placid when the pressure in the water tank approaches 3mm below the brink of the inner container the protection pressure switch might be broken or dislocated due to loose mounting screws Tighten the mounting screws and adjust the protection pressure switch as follows 1 Short circuit the normally open terminal and the common terminal of the working pressure switch 2 Unscrew the fastening screws in the adjusting plate of water level 3 Turn counterclockwise the adjusting screw in the adjusting plate of pressure till the required water level 4 Remove the short circuit cord on the working pressure switch and wrench tight the fastening screws in the adjusting plate of water level Try the pressure again If the pressure is higher than expected go over again the adjustment above till the requirement is met After adjustment seal the screws with thread gum Otherwise the screws may get loose causing the pressureto change XI Inlet Valve The inlet valve
21. the screws in the inlet valve support 100 replace the inlet valve with a new one and reconnect the tube and wire Connect the inlet hose when the dishwasher is ready XII Washing Pump Motor Assembly Water Pump Motor Assembly The dish washing is a joint accomplishment of the washing pump assembly 81 and the drain pump 86 The possible troubles of the washing pump assembly include motor damaged motor capacitor 76 damaged damaged pump sealing spring broken sealing broken connecting tube etc Steps for the check a Turn the power of the dishwasher to OFF and pull out the power cord plug b Remove the outer casing and turn the dishwasher upside down c Remove the connecting screws around the bottom panel and the screws to the motor support the drain motor and the pressure switch bracing bar d Checkhe capacitor if necessary replace a new one e Check the circulation pump for defects In case of defective pump replace it in the following manner 1 Remove the inlet hose clamp and the circulation pump 2 Replace a new circulation pump 3 Ption a new inlet hose clamp and connect the tubes and wires 4 Tighten the clamp e Check the drain pump In case of defective pump replace it in the following manner 1 Remove the inlet hose clamp and the drain pump 2 Replace a new drain pump 3 Put on a new inlet hose clamp and connect the tubes and wires 4 Tighten the clamp f Check the connecting tubes and replaced th
22. und terminals Removal and replacement 1 Disconnect the power prior to check 2 Check the power plug Improper connection may lead to bad contact 3 Pull out the power plug in one stroke Never pull at the power cord or use a knife or other sharp tools that may cut the cord 4 Check the power plug for overheat caused damage corrosion or looseness In case of troubles remove the outer casing 1 first then the rear panel 101 and replace the power cord see Process 6 5 Open the power cord clamp 96 remove the old power cord and replace a new one with terminals Secure the power terminals to the connection terminals and replace the power cord clamp 6 Replace the rear panel and the outer casing V Removal of Outer Casing Control Panel Rear This dishwasher is completely sealed In order to repair internal parts you have to remove the outer casing before you can check and repair the parts An ohmmeter and the ability to read circuit diagrams are needed in this step Removal and replacement 1 Turn all the switches to OFF and pull out the power cord plug 2 Remove the three screws on the sides of the outer casing 3 Open the door and remove the six screws in the front of the inner container see fig 1 below Note do not mix these stainless steel screws with the other ordinary ones Remove the seven screws in the back of the outer casing see fig 2 below Remove the screws in position D in fig 2 below an
Download Pdf Manuals
Related Search