SERVICE MANUAL
Contents
1. 2 To reassemble the components follow the above steps in reverse order 19 Front wall Dismantling the front wall according to IS 001 service manual 1 The rivets that fix the front wall to the appliance body must be removed by drill ing I 2 y Er gt N i Se f zei 2 To reassemble the components follow the above steps in reverse order Install new rivets after the repair that required removal of rivets by drilling Do not use screws the service technician must have a riveter 20 Fittings gas cooker Replacing the burner body 1 Dismantle the hob spark igniter and thermocouple according to relevant instruc tions in the manual e Z 3 To reassemble the components follow the above steps in reverse order 21 Fittings gas cooker Replacing the valve 1 Dismantle the hob dismantle the front panel assembly After dismantling or open ing the door remove the two screws that fix the gas pipe assembly to the cooker body 2 To replace the gas valve disconnect the thermocouple according to relevant in structions in this manual disconnect the pipe that supplies gas to the burner body 4 To reassemble the components follow the above steps in reverse order 22 Hob assembly electric cooker Replacing the cooking zones 1 Remove the screws that fix the hob in order to dismantle the hob Slide the hob toward the back yar 7 rn d 8 a P E o P gt 2 Place the2. SERVICE MANUAL Freestanding cooker 500 and 600 Range 2013 Gas gas Electric CFSGSV14 CFSGWH14 CFSESV14 CFSEWH14 Door assembly Removing the door assembly 1 Lift the lock of the left and right door hinge y E 3 Place the door on a flat surface with the handle facing downward Using a flat screwdriver pry the cap of the profile on one side to remove it Door assembly 4 Pull out the inner glass panel and carefully lift it Do the same with the middle glass panel s 5 Remove the screw that fastens the hinge to the inner glass profile Pull the hinge out of the profile A Refer to the Annex to the SBI_001 service manual Door assembly 7 Remove the door handle by undoing the screws 8 To reassemble the components follow the above steps in reverse order Oven chamber seal Dismantling the oven chamber seal 1 Unhook the seal holders from the front wall in four places in the corners m 2 To reassemble the components follow the above steps in reverse order The seal should be mounted with the joint facing down Knob assembly gas cooker 1 Pry the knob s interior part squeeze both parts together and pull toward your self 2 To reassemble the components follow the above steps in reverse order Impor tant There is a spring between the two elements Oven shelves Dismantling the shelf supports 1 Remove the runners from the shelf supports unhook the
3. en pulling the wires 6 Pull the new thermocouple wire through by pulling on the wire of the old thermo couple in the gap between the oven chamber and the side wall 7 Connect the new thermocouple Replace the oven spark igniter gas hob gas oven 1 Remove the oven door and the floor following the relevant instructions in the manual 2 Remove the gas spark igniter wire clip and pull the igniter from its holder 3 Install a new spark igniter by securing it in the holder using the wire clip a s 6 Replace the spark igniter following the same steps as when replacing the thermo couple i e bond the wiring of the new spark igniter with the wiring of the old one and then pull it though in the gap between the oven chamber and the side wall page 34 28 IS 003 2 EN 05 2014
4. gniter connector 1 Dismantle the knobs dismantle the front panel assembly Remove the washer located directly under the knob assembly on the valve stem Pry and turn the igniter assembly and remove it from the valve Repeat the procedure for all igniter connectors 2 To reassemble the components follow the above steps in reverse order 13 Temperature regulator assembly and function switch Dismantling the temperature regulator 1 Dismantle the hob dismantle the knob Disconnect the temperature regulator wiring harness Remove the two screws that fix the regulator uUBAUI MELO Cs 1037 ds SRS gyk k AN A ANA l 2 To reassemble the components follow the above steps in reverse order Dismantling the function switch 1 Dismantle the hob dismantle the knob Disconnect the function switch wiring har ness Remove the two screws that fix the function switch 14 Rotisserie motor assembly Replacing the rotisserie motor 1 Dismantle the rear wall by removing the screws on the sides Disconnect the wir ing harness from the rotisserie motor Remove the two screws that fix the rotis serie motor gt a WA 2 To reassemble the components follow the above steps in reverse order 15 Convection fan assembly Dismantling the fan 1 Remove the rear wall according to relevant instructions in the manual Remove the fan guard by removing the screws Remove the fan propeller by holding t
5. he fastening nut with the pliers and rotating propeller 3 To reassemble the components follow the above steps in reverse order 16 Bottom heater Dismantling the bottom heater 1 Dismantle the rear wall by removing the screws on the sides Disconnect the wir ing harness from the heater Gently remove the oven insulation pay special at tention not to damage delaminate the insulation Using a flat screwdriver gently deflect the catches securing the heater Slide the heater toward yourself N p P r en m A ps a PA 2 To reassemble the components follow the above steps in reverse order 17 Convection fan heater Dismantling the convection heater 1 Remove the rear wall and the fan guard according to relevant instructions in the manual Disconnect the wiring harness from the convection fan heater Using a socket head wrench undo and remove the nut securing the heater assembly P SPR a TE i a lt s lt d 2 Inside the oven chamber remove the screw securing the heater and pull the heater toward yourself 3 To reassemble the components follow the above steps in reverse order 18 Top heater Dismantling the top heater 1 Remove the rear wall according to relevant instructions in the manual Discon nect the wiring harness of the top heater Remove the nuts securing the heater to the oven chamber After unscrewing remove the heater from the oven chamber
6. hob upside down To dismantle the cooking zone undo the nut that fixes the cooking zone and disconnect the wiring harness 3 To reassemble the components follow the above steps in reverse order 23 Cam connector of the hot plate electric cooker Replacing the cooking zones 1 Dismantle the hob remove the knob by pulling it toward yourself Disconnect the wiring harness Remove the screws that fix the cam connector of the hot plate Slide the connector out 2 To reassemble the components follow the above steps in reverse order 24 Replace the oven burner gas hob gas oven 1 Remove the door following the relevant instructions in the manual 2 Unscrew the two screws that secure the floor of the oven then lift the floor and pull it towards you Replace the oven burner gas hob gas oven 5 Unscrew the screw securing the burner lift it and pull it towards you 26 Replace the oven thermocouple gas hob gas oven 1 Remove the oven door and the floor following the relevant instructions in the manual Remove the work plate 2 Remove the thermocouple wire clip and pull the thermocouple from its holder 3 Install a new thermocouple by securing it in the holder using the wire clip a 3 4 Disconnect the old thermocouple 5 Connect the socket of the new thermocouple to the end of the old one using the insulation tape The bond must be strong enough so that it does not break wh
7. shelf supports from the mounting holes 2 To reassemble the components follow the above steps in reverse order Hob gas cooker Dismantling the hob 1 To dismantle the cover assembly open it maximally to vertical position and pull it upward Remove the two screws that fix the hob to the freestanding cooker body gt ee A 7 3 Gently push the burner body to the inside pay special attention not to damage the thermocouple and spark igniter Hob gas cooker 4 Gently slide the hob toward the back and lift it 6 To reassemble the components follow the above steps in reverse order 10 Thermocouple gas cooker Replacing the thermocouple 1 Unhook the thermocouple from the valve Unhook the thermocouple lock located in the burner body prying it with a flat screwdriver ay x 2 Slide the thermocouple from the burner body guide y m Be A 3 To reassemble the components follow the above steps in reverse order 11 Front panel assembly Dismantling the front panel 1 Dismantle the door assembly Remove the two screws that fix the front panel to the freestanding cooker body The screws are located on the bottom of the panel and are visible after opening or dismounting the door Gently pull the panel to ward yourself 2 To reassemble the components follow the above steps in reverse order 12 Igniter connector assembly gas cooker Dismantling the i
Download Pdf Manuals
Related Search