Home

PJ358-1 User Guide, English

Contents

1. ACAUTION gt Please take right care of the projector according to the following Incorrect care could cause not only an injury but adverse influence such as discoloration peeling paint etc gt Do not use cleaners or chemicals other than those specified in this manual gt Do not polish or wipe with hard objects ViewSonic PJ358 60 www azulmarina com ventas azulmarina com www azulmarina com liroubleshooting If an abnormal operation should occur stop using the projector immediately Otherwise if a problem occurs with the projector the following checks and measures are recommended before requesting repair If this does not resolve the problem please contact your dealer or service company They will tell you what warranty condition is applied Related messages When some message appears check and cope with it according to the following table Although these messages will be automatically disappeared around several minutes it will be reappeared every time the power is turned on Message Description There i i i NO INPUT IS DETECTED EE pagna EEF Please confirm the signal input connection and the status of the signal source The horizontal or vertical frequency of the input signal SYNCHRO ee Hie is not within the specified range kHz FV gt KHz Please confirm the specs for your projector or the signal Source Specs The internal temperature is rising Please turn the power off and allow the proje
2. VCR DVD player VIDEO OUT AUDIO OUT Y e 5 e Clm GORO S VIDEO VIDEO NOTE e The COMPUTER INI port can support a component signal also For more information please see the description of the COMPUTER IN item of the INPUT menu ViewSonic PJ358 8 www azulmarina com ventas azulmarina com www azulmarina com Connecting your devices continued NOTE e Be sure to read the manuals for devices before connecting them to the projector and make sure that all the devices are suitable to be connected with this product Before connecting to a PC check the signal level the signal timing and the resolution Some signal may need an adapter to input this projector Some PCs have multiple screen display modes that may include some signals which are not supported by this projector Although the projector can display signals with resolution up to UXGA 1600X1200 the signal will be converted to the projector s panel resolution before being displayed The best display performance will be achieved if the resolutions of the input signal and the projector panel are identical e While connecting make sure that the shape of the cable s connector fits the port to connect with And be sure to tighten the screws on connectors with screws e When connecting a laptop PC to the projector be sure to activate the PC s extern
3. It will ask you if you start capturing an image from the a D Eu MED Current screen Please wait for the target image to be displayed and press the ENTER button when the image is displayed The image will freeze and the frame for capturing will appear To stop performing press the RESET or ESC button Using the A W lt buttons adjusts the frame position Please move the frame to the position of the image which you want to use The MyScreen frame may not be able to be moved for some input signals To start registration press the ENTER button To restore the screen and return to the previous dialog press the RESET or ESC button Registration takes several minutes When the registration is completed the registered screen and the following message is displayed for several seconds MyScreen registration is finished If the registration failed the following message is displayed A capturing error has occurred Please try again e This function cannot be selected when the TURN ON is selected to the MyScreen Lock item e This function cannot be selected when the TURN ON is selected to the MyScreen PASSWARD of SECURITY item in OPTION menu Using the AE buttons turns on off the MyScreen lock function TURN ON d TURN OFF When the TURN ON is selected the MyScreen item is locked Use this function for protecting the current MyScreen e This function cannot be selected when the TURN ON is selected to the MyScreen PASSWARD o
4. NOTE e The zoom level can be finely adjusted Closely watch the screen to find the level you want ViewSonic PJ358 18 www azulmarina com ventas azulmarina com www azulmarina com Freezing the screen 1 Press the FREEZE button on the remote control FREEZE The FREEZE indication will appear on the screen and the projector will go into the FREEZE mode To exit the FREEZE mode and restore the screen to normal press the FREEZE button again e The projector automatically exits from the FREEZE mode when one of the projector s buttons or remote control buttons of STANDBY ON SEARCH COMPUTER STORAGE VIDEO BLANK AUTO VOLUME MUTE KEYSTONE MENU MAGNIFY and MY BUTTON1 2 except MyMemory or PICTURE MODE is assigned to is pressed el the projector continues projecting a still image for a long time the LCD panel might possibly be burned in Do not leave the projector in the FREEZE mode for too long Temporarily blanking the screen 1 Press the BLANK button on the remote control The blank screen will be displayed instead of the screen of input signal Please refer to the BLANK item in the SCREEN menu To exit from the blank screen and return to the input signal screen press the BLANK button again e The projector automatically returns to the input signal screen when one of the projector s buttons or the remote control buttons except ASPECT POSITION or FREEZE button also except MY BUTTON1 2 if AUTO KEYSTONE or My
5. continued on next page ViewSonic PJ358 40 www azulmarina com ventas azulmarina com www azulmarina com OPTION Menu continued Description KEY LOCK Using the A V buttons turns on off the key lock feature When TURN ON is selected the buttons on the projector except the STANDBY ON button are locked TURN ON d TURN OFF e Please use to avoid a mischief and touching accidentally This function does not have any effect on the remote control REMOTE FREQ Use the A V button to change the Projector s remote sensor setting 1 NORMAL 2 HIGH Items with a checkmark are on The factory default setting is for both 1 NORMAL and 2 HIGH to be on If the remote control does not REMOTE FREQ function correctly set this to either only 1 or NORMAL a gt only 2 SERVICE Neither can be turned off at the same time continued INFORMATION Selecting this item displays a dialog titled INPUT INFORMATION It shows the information about the current input lt INPUT INFORMATION lt INPUT INFORMATION lt INPUT INFORMATION COMPUTER S VIDEO COMPUTER 1 1024x768 60 PAL 576i 50 FRAME LOCK ON AUTO e The FRAME LOCK message on the dialog means the frame lock function is working e This item can t be selected for no signal and sync out FACTORY RESET Selecting RESET using the button A performs this function By this function all the items in all of menus will collectively return to the initial setting Note that t
6. Any liability for the loss by mistake or malfunction shall not be assumed e Depends on USB Storage Devices Thumbnail display might disappears once at the beginning of connection and comes again Controlling the projector While Thumbnail menu is on screen some buttons on the projector and remote control are assigned some designated functions to support the menu operation If normal EASY or Advanced MENU on screen or INPUT SELECT function is required select PJ CONTROL item on the Thumbnail menu Use A WV lt and gt buttons to move a cursor to the PJ CONTROL item in Thumbnail menu Push ENTER button on the remote control or INPUT ENTER button on the projector to decide the selected item Following items can be controlled PJ CONTROL items Description Display EASY Advanced MENU of the projector Select MENU using A E lt and b buttons then push ENTER button on the remote control or INPUT ENTER button on the projector Change input port of the projector Select INPUT SELECT using A E lt and gt buttons then push ENTER button on the remote INPUT SELECT control or INPUT ENTER button on the projector so the input port will be changed from USB STORAGE to S VIDEO Then Thumbnail menu will be disappeared ViewSonic PJ358 50 www azulmarina com ventas azulmarina com www azulmarina com Displaying Thumbnail image Image files in USB storage can be seen as thumbnail display Use A V lt and gt button
7. SERVICE SECURITY USB STORAGE SCREEN EASY MENU Description AUTO SEARCH AUTO KEYSTONE AUTO ON Using the A V buttons turns on off the automatic signal search function TURN ON amp TURN OFF When the TURN ON is selected detecting no signal automatically cycles through input ports in the following order The search is started from the current port Then when an input is found the projector will stop searching and display the image eee IN1 gt COMPUTER INO Using the AE buttons turns on off the automatic keystone function TURN ON amp TURN OFF TURN ON Automatic keystone distortion correction will be executed whenever changing the slant of the projector TURN OFF This function is disabled Please execute the AUTO KEYSTONE JA EXECUTE in the SETUP Menu for automatic keystone distortion correction e When the projector is suspended from the ceiling this feature will not function properly so select the TURN OFF e This function will be unavailable when the Transition Detector is on Using the AE buttons turns on off the AUTO ON function TURN ON d TURN OFF When set to the TURN ON the lamp in projector will be automatically turned on without the usual procedure only when the projector is supplied with the power after the power was cut while the lamp was on e This function does not work as long as the power has been supplied to the projector while the lamp is off e After turning the lamp on by
8. displayed Temporary condition o saved data Odd Recall saved paramelers ER wit If you want to keep the current adjustment please press the lt button to quit Otherwise the current adjusted condition will be lost by loading a data e PICTURE MODE Changes the PICTURE MODE e FILTER RESET Displays the filter time reset confirmation dialogue e VOLUME Set the volume up e VOLUME Set the volume down Selecting this item displays the SERVICE menu Select an item using the A V buttons and press the b button or the ENTER button to execute the item FAN SPEED lt gt AUTO ADJUST lt gt GHOST lt gt FILTER MESSAGE lt gt KEY LOCK Larr RESET lt INFORMATION lt REMOTE FREQ J FAN SPEED Using the AE buttons switches the rotation speed of the cooling fans The HIGH is the mode for use at highlands etc Note that the projector is noisier when the HIGH is selected HIGH NORMAL SERVICE Gem continued on next page ViewSonic PJ358 39 www azulmarina com ventas azulmarina com www azulmarina com OPTION Menu continued Description AUTO ADJUST Using the A V buttons enables disables the automatic adjustment When DISABLE is selected the automatic adjustment feature is disabled although rough adjustment is automatically performed depending on the basic setting FINE FAST amp DISABLE Eee FINE Finer tuning including H SIZE adjustment FAST Faster tuning setting H SIZE
9. the menu will close If necessary repeat the process from 4 3 1 SECURITY 4 4 If you have forgotten your PASSWORD continued 4 4 1 Follow the procedure in 4 1 1 to display the Transition Detector on off menu 4 4 2 Select TURN OFF to display the ENTER ee PASSWORD BOX large The 10 digit pizza Inquiring Code will be displayed inside the BOX QUIT 4 4 3 Contact your dealer with the 10 digit Inquiring Code Your PASSWORD will be sent after your user registration information is confirmed Pressing the b button displays the USB STORAGE gt KEY CONFIG Menu a For more information please see the 1 Button e E USB STORAGE operation for still image of the Displaying an image in full screen under the USB STORAGE ViewSonic PJ358 47 www azulmarina com ventas azulmarina com www azulmarina com EISE GZESa E This projector has PC Less presentation feature that can display following files stored in USB storage or display as thumbnail without connecting PC NOTE 1 e Compliant file format File Format Maximum pixel size JPEG 8176 x 8176 M JPEG Motion JPEG 640 x 480 MPEG4 352 x 288 Progressive JPEG file cannot be reproduced Some JPEG files may not possible to display the image clearly e Compliant Audio format Audio Format Container format file extension 8bit or 16bit linear PCM AVI MP4 MPEG Layertaudo JI MPEG1 Layer II Audio and AAC Advanced Audio Coding can not be re
10. BRIGHTNESS and or CONTRAST settings to a higher level using the menu function Pictures appear The WHISPER function is working dark Select NORMAL for the WHISPER item in the SETUP menu The lamp is approaching the end of its product lifetime Replace the lamp Either the focus and or horizontal phase settings are not properly adjusted Pictures appear Adjust the focus using the focus ring and or H PHASE blurry using the menu function The lens is dirty or misty Clean the lens referring to the section Caring for the lens NOTE Although bright spots or dark spots may appear on the screen this is a unique characteristic of liquid crystal displays and it does not constitute or imply a machine defect ViewSonic PJ358 65 www azulmarina com ventas azulmarina com www azulmarina com Specifications Item Specification Product name Liquid crystal projector Liquid 1 6 cm 0 63 type Crystal TFT active matrix Panel 786 432 pixels 1024 horizontal x 768 vertical Zoom lens F 1 8 1 9 f 16 4 19 7 mm 5 35 C Operating 274 W x 59 H x 205 D mm Size Not including protruding parts Please refer to the following figure Weight mass 1 784 kg Computer input port Audio input output port COMPUTER IN Stereo mini x1 D sub 15 pin minix1 AUDIO OUT Stereo mini x1 COMPUTER IN2 Others D sub 15 pin mini x1 USB A x1 Video input port USB B x1 S video x1 video x1 Lamp RLC 027 Optional parts Air f
11. Play monitor ViewSonic PJ358 9 www azulmarina com ventas azulmarina com www azulmarina com Using a USB storage In order to view images stored in a USB storage such as a USB memory stick insert the device into the USB STORAGE port For more information please see the USB STORAGE Turn the projector off prior to removing the USB storage from the USB STORAGE port to prevent some troubles Connecting power supply POWER indicator 1 Put the connector of the power cord into 3 the AC inlet of the projector sl d Firmly plug the power cord s plug into AC inlet Sf the outlet In a couple of seconds after b Connector of the the power supply connection the POWER Ge indicator will light up in steady orange Please remember that when the AUTO ON function activated the connection of the power supply make the projector turn on Using the security slot This product has the security slot for the Kensington lock For details see the manual of the security tool Hurd dE aaa aa Security slot NOTE The security slot is not comprehensive theft prevention measures It is intended to be used as supplemental theft prevention measure ViewSonic PJ358 10 www azulmarina com ventas azulmarina com www azulmarina com Remote control Putting batteries Please set the batteries to the remote control before using it If the remote control starts to malfunction try to r
12. Using the AE buttons switches the noise reduction mode HIGH MID amp LOW e This function performs only for a video s video or component video of 525i 4801 or 625i 576i signal e When this function is excessive it may cause a certain degradation of the picture Using the AE buttons switches the mode for color space AUTO amp RGB SMPTE240 amp REC709 cx REC601 deei e This item can be selected only for a computer signal component video signal or a signal from the USB STORAGE port e The AUTO mode automatically selects the optimum mode e The AUTO operation may not work well at some signals In such a case it might be good to select a suitable mode except AUTO continued on next page ViewSonic PJ358 28 www azulmarina com ventas azulmarina com www azulmarina com INPUT Menu continued Description Set the video format for the s video port and video port 1 Use the lt gt buttons to select the input port VIDEO FORMAT 2 Using the AE buttons switches the mode S VIDEO VIDEO for video format AUTO NTSC amp PAL amp SECAM VIDEO FORMAT E N PAL amp M PAL amp NTSC4 43 A e This item is performed only for a video signal from the VIDEO port or the S VIDEO port e The AUTO mode automatically selects the optimum mode e The AUTO operation may not work well for some signals If the picture becomes unstable e g an irregular picture lack of color please select the mode according
13. concise which is a book Your projector should come with the items shown there Contact immediately your dealer if anything is missing NOTE e Keep the original packing materials for future reshipment Be sure to use the original packing materials when moving the projector Use special caution for the lens Fastening the lens cover To avoid losing the lens cover please fasten the lens cover to the projector using the enclosed strap 1 Fix the strap to the strap hole of the lens cover Thread one end of the strap through the strap hole of the lens cover and make the loop at the end and let the other end of the strap through the loop Not have a knot in the strap at either end Strap hole a Fix the strap to the strap hole of the projector Thread the other end of the strap through the strap hole of the projector and make the loop there Let the lens cover with the one end of strap though the loop Replacing the filter cover for bottom up use For the projector installed bottom up please replace the filter cover with the enclosed filter cover for bottom up use to keep necessary ventilation space eg Please refer to the Air filter for how to detach GIRO 80022300 AAAA 300 and attach a filter cover Gia f EA ee Y WE Lee ONE Sec gt yy Filter cover ViewSonic PJ358 3 www azulmarina com ventas azulmarina com www azulmarina com BEK NEMES Projector 1 Lamp cover The lamp unit is ins
14. es 6 Arrangement 020005 6 Connecting your devices 8 Using a USB storage 10 Connecting power supply 10 Using the security slot 10 Remote control 11 Putting batteries 11 About the remote control signal 11 Changing the frequency of remote control signal b 4 gm amp 12 Using as a simple PC mouse amp keyboard 12 Power on off da Turning on the power 13 Turning off the power 13 Operating A A 14 Adjusting the volume 14 Temporarily muting the sound 14 Selecting an input signal 14 Searching an input signal 15 Selecting an aspect ratio 15 Adjusting the projector s elevator 16 Adjusting the zoom and focus 16 Using the automatic adjustment feature 17 Adjusting the position Correcting the keystone distortions 18 Using the magnify feature Freezing the screen 19 Temporarily blanking the screen 19 Using the menu function PJ358 www azulmarina com ViewSonic www azulmarina com EASY MENU Aspect AUTO KEYSTONE HN EXECUTE KEYSTONE HAL PICTURE MODE BRIGHTNESS CONTRAST COLOR TINT SHARPNESS Whisper MIRROR RESET FILTER TIME LANGUAGE Go to Advanced Menu PICTURE menu 23 BRIGHTNESS CONTRAST GAMMA COLOR TEMP Cotor TINT SHARPNESS My MEMORY IMAGE menu 26 ASPECT OVE
15. injury from tipping over Unplug this equipment when it will be unused for long periods of time Refer all servicing to qualified service personnel Service is required when the unit has been damaged in any way such as if the power supply cord or plug is damaged if liquid is spilled onto or objects fall into the unit if the unit is exposed to rain or moisture or if the unit does not operate normally or has been dropped ViewSonic PJ358 ii www azulmarina com ventas azulmarina com www azulmarina com Declaration of ROHS Compliance This product has been designed and manufactured in compliance with Directive 2002 95 EC of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment ROHS Directive and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee TAC as shown below Proposed Maximum Actual Concentration Concentration Hexavalent Chromium SE lt 01 Polybrominated biphenyls PBB lt 01 Polybrominated diphenyl ethers PBDE lt 0 1 Certain components of products as stated above are exempted under the Annex of the RoHS Directives as noted below Examples of exempted components are 1 Mercury in compact fluorescent lamps not exceeding 5 mg per lamp and in other lamps not specifically mentioned in the Annex of RoHS Directive 2 Lead in glass of cathode ray tubes electronic
16. is not available while the lamp is warming up the POWER indicator flashes green and while adjusting the volume and display correcting for keystone zooming in on the screen using the BLANK function or displaying the menu screen ViewSonic PJ358 be www azulmarina com ventas azulmarina com www azulmarina com EOS OROI Turning on the power STANDBY ON button Make sure that the POWER indicator turns in POWER indicator steady orange and the lens cover is removed Press the STANDBY ON button on the projector or the remote control The projection lamp will light up and the POWER indicator will begin blinking in green When the power is completely on the indicator will stop blinking and light in steady green To display the picture select an input signal according to the section Selecting an input signal Lens cover Turning off the power 1 Press the STANDBY ON button on the projector or the remote control The message Power off will appear on the screen for about 5 seconds Press the STANDBY ON button again while the message appears The projector lamp will go off and the POWER indicator will begin blinking in orange Then the POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete 3 Attach the lens cover after the POWER indicator turns in steady orange Do not turn the projector on for about 10 minutes after turning it off Turning the projector on again to
17. it is 4th layer 0 Folder D Folder E c Folder G F Folder F e Picture may not be displayed correctly depending on the connecting device in case that an extended USB cable is used e Response time might vary depending on each image contents when switching pages loading files and playing each movie e When there are following icons on thumbnail display it might be non compliant file Check the saved file in USB storage Description This is un displayable file Check the format of saved file Refer to NOTE1 This motion picture file does not contain audio clip or cannot be reproduced sound Refer to NOTE 1 ViewSonic PJ358 52 www azulmarina com ventas azulmarina com www azulmarina com Playing Slide show SLIDE SHOW can displays a full screen image and change it to the next one in desired interval time Use A V lt and gt buttons to move a cursor to SLIDE SHOW item in Thumbnail menu push ENTER button on the remote control or INPUT ENTER button on the projector to decide it SLIDE SHOW items Description Starts SLIDE SHOW Select PLAY using A V lt and gt buttons then push ENTER button on the remote control or INPUT ENTER button on the projector Specify and select image file number in thumbnail display as starting number for SLIDE SHOW Select START using A V lt and gt buttons then push ENTER button on the remote control or INPUT ENTER button o
18. oer a e Select an item using the AIE cursor buttons Then perform ud 3 it according to the following table Said NORMAL MIRROR NORMAL RESET FILTER TIME 123h LANGUAGE ENGLISH Go to Advanced Menu Item Description Using the lt gt buttons switches the mode for aspect ratio ASPECT See the ASPECT item in IMAGE menu E Using the button executes the auto keystone function Ae See the AUTO KEYSTONE KA EXECUTE item in SETUP menu Using the lt gt buttons corrects the vertical keystone distortion SENS ONE See the KEYSTONE item in SETUP menu Using the lt gt buttons switches the picture mode The picture modes are combinations of GAMMA and COLOR TEMP settings Choose a suitable mode according to the projected SOUICE NORMAL amp CINEMA ZO DYNAMIC Lardi DAYLIGHT MODE So erd badi COLOR TEMP GAMMA NORMAL MID DEFAULT 1 DEFAULT PICTURE MODE e When the combination of GAMMA and COLOR TEMP differs from pre assigned modes above the display on the menu for the PICTURE MODE is CUSTOM Please refer to the GAMMA and COLOR TEMP items in PICTURE menu e When this function is performed a certain extra such as a line may appear continued on next page ViewSonic PJ358 21 www azulmarina com ventas azulmarina com www azulmarina com EASY MENU continued Item Description Using the lt gt buttons adjusts the brightness BRIGHTNESS See the BRIGHTNESS item in PICT
19. only when the AUTO mode is selected to the VIDEO FORMAT item in INPUT menu The vertical position horizontal position and aspect ratio will be automatically set to the the default For a component video signal also the horizontal phase will be automatically set to the default e The automatic adjustment operation requires about 10 seconds Also please note that it may not function correctly with some input ViewSonic PJ358 27 www azulmarina com ventas azulmarina com www azulmarina com INER MIS From the INPUT menu items shown in the table below can be performed PROGRESSIVE FILM VIDEO NR MID COLOR SPACE AUTO Select an item using the A V cursor buttons and press VIDEO FORMAT FRAME LOCK TURN OFF the gt cursor button or ENTER button to execute the item Gere Then perform it according to the following table EASY MENU RESOLUTION Description PROGRESSIVE VIDEO NR COLOR SPACE Using the AE buttons switches the progress mode TV FILM amp TURN OFF e This function is performed only for an interlaced signal of a video s video or component video of 525i 4801 or 625i 576i signal e When TV or FILM is selected the screen image will be sharp FILM adapts to the 2 3 Pull Down conversion system But these may cause a certain defect for example jagged line of the picture for a quick moving object In such a case please select TURN OFF even though the screen image may lose the sharpness
20. sensor senses the signal within the following range when the sensor Is active 60 degrees 30 degrees to the left and right of the sensor within 3 meters about NOTE The remote control signal reflected in the screen or the like may be available If it is difficult to send the signal to the sensor directly attempt to make the signal reflect e The remote control uses infrared light to send signals to the projector Class 1 LED So be sure to use the remote control in an area free from obstacles that could block the remote control s signal to the projector e The remote control may not work correctly if strong light such as direct sun light or light from an extremely close range such as from an inverter fluorescent lamp shines on the remote sensor of the projector Adjust the position of projector avoiding those lights ViewSonic PJ358 11 www azulmarina com ventas azulmarina com www azulmarina com Changing the frequency of remote control signal The accessory remote control has the two choices on signal frequency Mode 1 and Mode 2 If the remote control does not function properly attempt to change the signal frequency In order to set the Mode please keep pressing the combination of two buttons listed below simultaneously for about 3 seconds 1 Set to Mode 1 MUTE and RESET buttons 2 Set to Mode 2 MAGNIFY OFF and ESC buttons Please remember that the REMOTE FREQ in the SERVICE item of the OPTION menu of the pr
21. that the application window is set to its maximum size prior to attempting to use this feature A dark picture may still be incorrectly adjusted Use a bright picture when adjusting O Fora signal from the USB STORAGE The aspect ratio will be automatically set to the default O For a video signal s video signal or component video signal The video format best suited for the respective input signal will be selected automatically This function is available only when the AUTO is selected for the VIDEO FORMAT item in the INPUT menu The vertical position horizontal position and aspect ratio will be automatically set to the default For a component video signal also the horizontal phase will be automatically set to the default e The automatic adjustment operation requires about 10 seconds Also please note that it may not function correctly with some input When this function is performed for a video signal a certain extra such as a line may appear outside a picture Adjusting the position 1 Press the POSITION button on the remote control The POSITION indication will appear on the screen Use the AIEK cursor buttons to adjust the picture position When you want to reset the operation press the RESET button on the remote control during the operation To complete this operation press the POSITION button again Even if you do not do anything the dialog will automatically disappear after a few seconds e The POSITION butt
22. the previous resolution e For some pictures this function may not work well ViewSonic PJ358 30 www azulmarina com ventas azulmarina com www azulmarina com SERUP Menu From the SETUP menu items shown in the table below can be performed AUTO KEYSTONE EXECUTE KEYSTONE 0 NORMAL Select an item using the AE cursor buttons and press NORMAL the cursor button on the ENTER button to execute the item Then perform it according to the following table 16 EASY MENU Description AUTO KEYSTONE EXECUTE KEYSTONE Selecting this item performs the automatic keystone distortion correction Projector automatically corrects vertical keystone distortion due to the forward backward setup angle by itself This function will be executed only once when selected in the menu When the slant of the projector is changed execute this function again e The adjustable range for correction will vary among inputs For some input this function may not work well e When V INVERT or H amp V INVERT is selected to the MIRROR item in the SETUP menu if the projector screen is inclined or angled downward this function may not work correctly e When the zoom adjustment is set to the TELE telephoto focus this function may be excessive This function should be used when the zoom adjustment is set to the full WIDE wide angle focus whenever possible e When the projector is placed on the level about 0 th
23. the AUTO ON function if neither input nor operation is detected for about 30 minutes the projector is turned off even though the AUTO OFF function is disabled VIDEO S VIDEO e USB STORAGE continued on next page ViewSonic PJ358 www azulmarina com 37 ventas azulmarina com www azulmarina com OPTION Menu continued Description Using the AE buttons adjusts the time to count down to automatically turn the projector off Long max 99 minutes Short min D minute DISABLE d AUTO OFF d AUTO OFF ENABLE DISABLE A A When the time Is set to 0 the projector is not turned off automatically When the time is set to 1 to 99 and when the passed time with no signal or an unsuitable signal reaches at the set time the projector lamp will be turned off If one of the projector s buttons or the remote control buttons is pressed or one of the commands except get commands Is transmitted to the control port during the corresponding time projector will not be turned off Please refer to the section Turning off the power AUTO OFF The lamp time is the time counted after the last resetting It is shown in the OPTION menu as the usage time of the lamp Pressing the RESET button or the b button displays a dialog To reset the lamp time select the RESET using the A button RESET amp CANCEL e Please reset the lamp time only when you have replaced the lamp for a suitable indication about the la
24. the cursor to the right side of the ENTER NEW PASSWORD BOX and press the gt button to display the NEW PASSWORD AGAIN BOX enter the same PASSWORD again 1 2 4 Move the cursor to the right side of the NEW PASSWORD AGAIN BOX and press the gt button and the NOTE NEW PASSWORD BOX will be displayed for about 20 seconds please make note of the PASSWORD during this time Pressing the ENTER button will close the NOTE NEW PASSWORD BOX e Please do not forget your PASSWORD continued on next page SECURITY ENTER PASSWORD A 40 0 0 OP Ka QUIT NEXT gt SECURITY PASSWORD CHANGE MyScreen PASSWORD TURN OFF TRANSITION DETECTOR TURN OFF SECURITY ENTER NEW PASSWORD SECURITY NEW PASSWORD AGAIN aX SECURITY NOTE NEW PASSWORD 0000 ENTER J EXIT ViewSonic PJ358 42 www azulmarina com ventas azulmarina com www azulmarina com OPTION Menu continued Description 1 3 If you have forgotten your PASSWORD 1 3 1 Follow the procedure in 1 1 1 to display the ENTER PASSWORD BOX 1 3 2 While the ENTER PASSWORD BOX is displayed press and hold the RESET button for about 3 seconds or press and hold the INPUT and b buttons on the projector for about 3 seconds The 10 digit Inquiring Code will be displayed e If there is no key input for about 55 seconds while the Inquiring Code is displayed the menu will close If necessary repeat the process from 1 3 1 SECURITY PASSWORD Inquiring Code 0 12345 6
25. to prearranged data for the input signal e Depending on conditions such as input image signal cable to the projector environment around the projector etc the automatic adjustment may not work correctly In such a case please choose DISABLE to disable the automatic adjustment and make adjustment manually GHOST 1 Select a color element of ghost using the lt gt R G B SERVICE buttons 2 Adjust the selected element using the AE buttons to GHOST disappear ghost FILTER MESSAGE Use the A V button to set the timer for the interval to show the message for cleaning up the air filter Eege 50h 100h 200h 300h TURN OFF eei After selecting 50h 100h 200h or 300h the O OI message REMINDER van HRS PASSED AFTER THE ZZ IE ZE LAST FILTER CHECK will appear after the timer reaches the interval time set by the menu When the TURN OFF is chosen the air filter cleaning message will not appear e Please check and clean the air filter periodically even if there is no message If the air filter becomes to be blocked by dust or others the internal temperature will rise which could cause malfunction or reduce the lifetime of the projector e It is recommended to choose 100h in general Please be careful with the operating environment of the projector and the condition of the air filter especially when the 200h 300h or TURN OFF is chosen continued
26. to the input signal Using the A V buttons turns the frame lock function on off TURN ON amp TURN OFF e This item can be performed only on a computer signal with a FRAME LOCK vertical frequency of 50 to 60 Hz e When the TURN ON is selected a moving pictures are displayed more smoothly e This function may cause a certain degradation of the picture In such a case please select the TURN OFF Set the computer input signal type for the ports of COMPUTER 1 Use the lt gt buttons to select a COMPUTER port to be set COMPUTER IN1 amp COMPUTER INO 2 Use the AE buttons to select the computer input signal type AUTO amp SYNC ON G OFF COMPUTER IN Sync on Green signal can be supported if AUTO is selected e When the AUTO is selected the picture may be distorted with certain input signals In such a case remove the signal connector first and select SYNC ON G OFF on the menu and then reconnect the signal e Component signal can be supported through COMPUTER IN port if AUTO is selected for the COMPUTER INI port continued on next page ViewSonic PJ358 29 www azulmarina com ventas azulmarina com www azulmarina com INPUT Menu continued Description The resolution for the COMPUTER IN1 and COMPUTER IN2 input signals can be set on this projector 1 In the INPUT menu select the RESOLUTION using the AE buttons and press the b button The RESOLUTION menu will be displayed d RESOLUTION 2 In the RES
27. 789 1 3 3 Contact your dealer with the 10 digit Inquiring Code Your PASSWORD will be sent after your user registration information is confirmed 2 Using the MyScreen PASSWORD Function The MyScreen PASSWORD function can be used to prohibit access to the MyScreen function and prevent the currently registered MyScreen image from being overwritten 2 1 Turning on the MyScreen PASSWORD Function 2 1 1 Use the AE buttons on the SECURITY menu to select MyScreen PASSWORD and press the b button to display the MyScreen PASSWORD on off menu SECURITY continued 2 2 Setting the PASSWORD 2 2 1 Display the MyScreen on off menu using the procedure in 2 1 1 2 2 2 Use the A V buttons on the MyScreen PASSWORD on off menu to select TURN ON The ENTER PASSWORD BOX small will be displayed 2 2 3 Use the AET db buttons to enter the PASSWORD Move the cursor to the right side of the ENTER PASSWORD BOX small and press the b button to display the CHECK PASSWORD BOX enter the same PASSWORD again continued on next page PJ358 www azulmarina com ViewSonic lt MyScreen PASSWORD O TURN ON e TURN OFF MyScreen ENTER PASSWORD A 40 0 0 OP KE UI NEXT gt MyScreen CHECK PASSWORD A d 0 0 OP 7 QUIT NEXT gt 43 ventas azulmarina com www azulmarina com OPTION Menu continued Description 2 2 4 Move the cursor to the right side of the CHECK PASSWORD BOX and press the MyScreen b button to di
28. 8 www azulmarina com ventas azulmarina com www azulmarina com Displaying Thumbnail Menu continued Thumbnail Display Menu SS aei PJ_CONTROL MENU 1 abcdefgh 2 abcdefgh 3 abcdefgh THUMBNAIL N IMAGE All A Page Up E Page Down ba J ba J A E 4 abcdefgh 5 abcdefgh 6 abcdefgh e E TN a N LIDE SHOW PLAY START 1 STOP 999 INTERVAL 123s MODE ONE TIME u SCREEN EFFECT 1 A St b J NS J 7 abcdefgh 8 abcdefgh 9 abcdefgh w bai beree 10 abcdefgh 11 abcdefgh 12 abcdefgh SCH SELECT ENTER ISI om Thumbnail Menu Displaying Thumbnail Menu continued The PC LESS Presentation can be controlled via control panel on the projector or the remote control Following button operations can be valid while Thumbnail menu is displayed Item Description AIZ Tddib on Remote control Move cursor Control panel Works as ENTER function ENTER Display selected image in full screen when the cursor is on Remote control pointed one of the image on Thumbnail Display in Thumbnail INPUT ENTER menu on Control panel Select Thumbnail Menu item when the cursor is at the menu in Thumbnail menu NOTE 2 e Do not connect any apparatus other than USB storage devices and other equipments for battery charge through USB It causes malfunction e Insert only one memory card even though USB ca
29. IDE SHOW playing at ONE TIME or ENDLESS 1 Select MODE using A V lt and b buttons then push ENTER button on the remote control or INPUT ENTER button on the projector so that MODE setting can be selected 2 Change MODE setting using A and Wbuttons ONE TIME gt ENDLESS Playing Slide Show Playing Slide Show only one time endless 3 Get out from the status that MODE setting is selectable by pushing ENTER button on the remote control or INPUT ENTER button on the projector Select SCREEN EFFECT for slide change in SLIDE SHOW 1 Select SCREEN EFFECT using A V lt and gt buttons then push ENTER button on the remote control or INPUT ENTER button on the projector so that SCREEN EFFECT setting can be selected SCREEN EFFECT 2 Change SCREEN EFFECT setting using A and WY buttons OFF 1 2 no effect Sliced IN Minced IN Get out from the status that SCREEN EFFECT setting is selectable by pushing ENTER button on the remote control or INPUT ENTER button on the projector NOTE 4 e If the number specified for START is bigger than the number specified for STOP slide show is not executed e When the file size selected for SLIDE SHOW is big the actual interval time may be longer than the set time at INTERVAL menu e When a motion image is selected for SLIDE SHOW the next slide will be displayed after the play of the motion image is ended regardless of whatever is set at INTERVAL men
30. L BLUE WHITE BLACK e To avoid remaining as an afterimage the MyScreen or ORIGINAL screen will change to the plain black screen after several minutes continued on next page ViewSonic www azulmarina com PJ358 33 ventas azulmarina com www azulmarina com SCREEN Menu continued Description Using the AE buttons switches the mode for the start up screen The start up screen is a screen displayed when no signal or an unsuitable signal is detected MyScreen ORIGINAL go TURN OFF died Feature MyScreen Screen can be registered by the MyScreen item ORIGINAL Screen preset as the standard screen GARAIA TURN OFF Plain black screen e To avoid remaining as an afterimage the MyScreen or ORIGINAL screen will change to the BLANK screen after several minutes If also the BLANK screen is the MyScreen or ORIGINAL the plain black screen is instead used e When the TURN ON is selected to the MyScreen PASSWARD of SECURITY item in OPTION menu the START UP is fixed to MyScreen continued on next page ViewSonic PJ358 34 www azulmarina com ventas azulmarina com www azulmarina com SCREEN Menu continued Description This item allows you to capture an image for use as a MyScreen image which can be used as the BLANK screen and START UP screen Display the image you want to capture before executing the following procedure 1 Selecting this item displays a dialog titled MyScreen
31. Memory or PICTURE MODE is assigned on these buttons is pressed NOTE e The sound is not connected with the blank screen function If necessary set the volume or mute first ViewSonic PJ358 19 www azulmarina com ventas azulmarina com www azulmarina com Using the menu function This projector has the following menus PICTURE IMAGE INPUT SETUP SCREEN OPTION and EASY MENU EASY MENU consists of functions often used and the other menus are classified into each purpose Each of these menus is operated using the same methods The basic operations of these menus are as follows _ Press the MENU INPUT ENTER button ENTER button MENU button button on the remote MENU button Cursor buttons control or the projector si Am 1 1 1 en e The Advanced MENU KIN or EASY MENU that SE has priority just after ON C powered on will appear While the projector is displaying any menu the INPUT ENTER button on the projector works as ne ENTER button and the MENU button on the projector works as the cursor uttons In the EASY MENU lf you want to change it to the Advanced TI Cour Menu select the Go to Advanced PICTURE MODE CUSTOM D BRIGHTNESS eie Menu CONTRAST COLOR Es Use the AE cursor buttons to select an rm E da a e i t em t o oper at e SHARPNESS IMAGE CONTRAST 0 H Sd SETUP COLOR me we Use the lt gt cursor buttons to operate SCREEN
32. OLUTION menu select the STANDARD O 1024x 768 resolution you wish to display using the AE 1280x 768 buttons 1360x 768 Selecting AUTO will set a resolution CUSTOM 1440x 768 gt appropriate to the input signal 3 Pressing the b or ENTER button when selecting a STANDARD resolution will automatically adjust the horizontal and vertical positions clock phase and horizontal size and automatically select an aspect ratio The INFORMATION dialog will be displayed 4 To set a custom resolution use the A V buttons to select the CUSTOM and CUSTOM RESOLUTION HORZ x VERT 0992 x 0744 the CUSTOM RESOLUTION box will be RESOLUTION displayed Set the horizontal HORZ and vertical VERT resolutions using the A V lt P buttons Although not all resolutions are guaranteed 5 To save the setting place the cursor on the right most digit and press the button The horizontal and vertical positions 992x 744 60 clock phase and horizontal size will be automatically adjusted and an aspect ratio will be automatically selected After the INFORMATION dialog has displayed for about 10 seconds the screen will return STANDARD O 1024x 768 to the RESOLUTION menu displaying the 1280x 768 changed resolution O 1360x 768 6 To revert back to the previous resolution without saving changes place the cursor on the left most digit and press the lt button The screen will then return to the RESOLUTION menu displaying
33. R SCAN V POSITION H POSITION H PHASE H size AUTO ADJUST EXECUTE INPUT menu PROGRESSIVE VIDEO NR COLOR SPACE VIDEO FORMAT FRAME LOCK COMPUTER IN RESOLUTION SETUP menu 31 AUTO KEYSTONE J EXECUTE KEYSTONE EA WuisPer Mirror VOLUME AUDIO SCREEN menu e eu LANGUAGE MENU POSITION BLANK START UP MyScreen MyScreen Lock MESSAGE SOURCE NAME OPTION menu 37 AUTO SEARCH AUTO KEYSTONE HAL AUTO ON AUTO OFF LAMP TIME FILTER TIME My BUTTON SERVICE Security USB STORAGE USB STORAGE wv 48 Maintenance 57 Lamp ee un e T 57 Air filter w e A Ad 59 Other care 60 Troubleshooting 61 Related messages 61 Regarding the indicator lamps 62 Phenomena that may be easy to be mistaken for machine defects 64 Specifications 66 ventas azulmarina com www azulmarina com EOISGIOT IGOTZE This projector has a capability to project various picture signals onto a screen This projector requires only a minimal amount of space for installation and can produce a large projected image from even a short distance This projector also can give a benefit to mobile users and others by offering a special function named PC less presentation Even without PC this projector realizes the display on screen getting JPEG MPEG and Motion JPEG pictures from USB storage media Contents of package Please see the Contents of package in the User s Manual
34. RAGE e This setting is effective only when a signal from the USB STORAGE port is selected ViewSonic PJ358 32 www azulmarina com ventas azulmarina com www azulmarina com SAREEN Men From the SCREEN menu items shown in the table below can be performed Select an item using the A V cursor buttons and press the b cursor button or ENTER button to execute the item Then perform it according to the following table ENGLISH PICTURE LANGUAGE IMAGE MENU POSITION INPUT BLANK BLACK SETUP START UP ORIGINAL MyScreen OPTION MyScreen Lock TURN OFF EASY MENU MESSAGE TURN ON SOURCE NAME Description LANGUAGE MENU POSITION Using the A buttons switches the OSD On Screen Display language ENGLISH amp FRANCAIS go DEUTSCH amp ESPANOL amp ITALIANO NORSK o NEDERLANDS amp PORTUGUES B dS fa BC gihe StS SVENSKA DYCK SUOMI POLSKI go T RK E Using the AEK buttons adjusts the menu position To quit the operation press the MENU button on the remote control or keep no operation for about 10 seconds Using the A V buttons switches the mode for the blank screen The blank screen is a screen for the temporarily blanking feature It is displayed by pressing the BLANK button MyScreen amp ORIGINAL amp BLUE amp WHITE amp BLACK pa s SS a SS EE Feature Screen can be registered by the MyScreen item Screen preset as the standard screen Plain screens in each color MyScreen ORIGINA
35. URE menu Using the lt gt buttons adjusts the contrast CONTRAST See the CONTRAST item in PICTURE menu COLOR Using the lt gt buttons adjusts the strength of whole color See the COLOR item in PICTURE menu TINT Using the lt gt buttons adjusts the tint See the TINT item in PICTURE menu Using the ak buttons adjusts the sharpness See the SHARPNESS item in PICTURE menu Using the lt gt buttons turns off on the whisper mode WHISPER See the WHISPER item in SETUP menu MIRROR Using the lt gt buttons switches the mode for mirror status See the MIRROR item in SETUP menu Performing this item resets all of the EASY MENU items except the FILTER TIME and LANGUAGE A dialog is displayed for confirmation Selecting the RESET using the A button performs resetting Performing this item resets the filter time which counts usage time of the air filter FILTER TIME A dialog is displayed for confirmation Selecting the RESET using the A button performs resetting See the FILTER TIME item in OPTION menu Using the dib buttons changes the display language LANGUAGE See the LANGUAGE item in SCREEN menu Go to Select Go to Advanced Menu on the menu and press the gt Advanced Menu 2 ENTER button to use the menu of PICTURE IMAGE INPUT SETUP SCREEN or OPTION ViewSonic PJ358 22 www azulmarina com ventas azulmarina com www azulmarina com PIGMURE Menu From the PICTURE menu items shown in
36. ViewSonic PJ358 LCD Projector User Guide Guide de l utilisateur Bedienungsanleitung Gu a del usuario Guida dell utente RIER ORIETAKO Anv ndarhandbok K ytt opas PykoBoacTBO NOonb30BaTena CAFM SE EAFA tei A ViewSonic Model No VS11611 www azulmarina com wWww azulmarina com Compliance Information For U S A This device complies with part 15 of FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenn
37. a e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Warning You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment For Canada e This Class B digital apparatus complies with Canadian ICES 003 e Cet appareil num rique de la classe B est conforme a la norme NMB 003 du Canada CE Conformity for European Countries EEC as amended by 92 31 EEC and 93 68 EEC Art 5 with regard to Electromagnetic compatibility and 73 23 EEC as amended by 93 68 EEC C The device complies with the requirements of the EEC directive 89 336 Art 13 with regard to Safety Following information is only for EU member states The mark shown to the right is in compliance with the Waste Electrical and Electronic Equipment Directive 2002 96 EC WEEE The mark indicates the requirement NOT to dispose the equipment as unsorted municipal waste but use the return and collection systems according to local law ViewSonic PJ358 www azulmarina com ventas azulmarina com www azulmarina com Important Safety Instructions ao Fa R 10 11 12 13 14 Read these instructions completely before using the equipment Keep these instructions in a sa
38. al RGB output Set the laptop PC to CRT display or to simultaneous LCD and CRT display For details on how this is done please refer to the instruction manual of the corresponding laptop PC e When the picture resolution is changed on a pc depending on an input automatic adjustment function may take some time and may not be completed In this case you may not be able to see a check box to select Yes No for the new resolution on Windows Then the resolution will go back to the original It might be recommended to use other CRT or LCD monitors to change the resolution e In some cases this projector may not display a proper picture or display any picture on screen For example automatic adjustment may not function correctly with some input signals An input signal of composite sync or sync on G may confuse this projector so the projector may not display a proper picture About Plug and Play capability Plug and Play is a system composed of a PC its operating system and peripheral equipment i e display devices This projector is VESA DDC 2B compatible Plug and Play can be used by connecting this projector to a pc that is VESA DDC display data channel compatible e Take advantage of this feature by connecting an RGB cable to the COMPUTER IN port DDC 2B compatible Plug and Play may not work properly if any other type of connection is attempted e Please use the standard drivers in your pc as this projector is a Plug and
39. appear on screen if the projector has been moved or re installed e Transition Detector alarm might appear on screen if the MIRROR setting has been changed e Keystone adjustment feature has been prohibited as long as the Transition Detector function is ON 4 1 Turning On the Transition Detector Function 4 1 1 Use the AE buttons on the SECURITY menu to select Transition Detector and press the or the TRANSITION DETECTOR ENTER button to display the Transition Detector O TURN ON on off menu TURN OFF Select TURN ON and the current angle and mirror setting will be recorded e This feature may not function properly if the projector is not in a stable position when TURN ON is selected 4 1 2 If this function is set to TURN ON when the vertical angle of the projector or mirror setting M n ee at which the projector is turned on is different from previously installed position than the previously recorded the Transition hyeu wien to haara Guara tag Detector Alarm will be displayed and the disable Transition Detector on Menu projector will not display the input signal SECURITY Set the Transition Detector off in the SECURITY menu to display the input signal continued If the Transition Detector ALARM is displayed for about 5 minutes the lamp will turn off This function will activate only when the projector is started after the power switch was turned off 4 2 Setting the Transition Detector PASSWORD 4 2 1 Use the A V button
40. bar 1 The darkest tone at the left end of the test pattern cannot be controlled with any of equalizing adjustment bar e When this function is performed lines or other distortion may appear continued on next page ViewSonic PJ358 23 www azulmarina com ventas azulmarina com www azulmarina com PICTURE Menu continued Description Using the AE buttons switches the color temperature mode rz HIGH DEFAULT HIGH CUSTOM amp MID DEFAULT amp MID CUSTOM J LOW DEFAULT amp LOW CUSTOM Hi BRIGHT 1 DEFAULT Hi BRIGHT 1 CUSTOM gt Hi BRIGHT 2 DEFAULT Hi BRIGHT 2 CUSTOM lt To adjust CUSTOM Selecting a mode whose name includes CUSTOM and then pressing the b button or the ENTER button displays a dialog to aid you in adjusting the OFFSET and GAIN of the selected mode d HHH OFFSET adjustments change the color intensity dgn 0 0 dk COLOR TEMP on the whole tones of the test pattern om GAIN adjustments mainly affect color intensity on the brighter tones of the test pattern Choose an item using the lt gt buttons and adjust the level using the AE buttons You can display a test pattern for checking the effect of your adjustment by pressing the ENTER button Each time you press the ENTER button the pattern changes as below No pattern gt Gray scale of 9 steps t Ramp Gray scale of 15 steps e When this function is performed lines or other dist
41. ch stops operation of the projector without cooling it down ViewSonic PJ358 4 www azulmarina com ventas azulmarina com Control panel 1 STANDBY ON button 2 INPUT ENTER button 3 MENU button It consists of four cursor buttons 4 POWER indicator 5 TEMP indicator 6 LAMP indicator Remote control VOLUME button MUTE button FREEZE button MY BUTTON 1 button MY BUTTON 2 button KEYSTONE button ViewSonic PJ358 www azulmarina com www azulmarina com it Wmd ii Lu eZ ed 2 3 Ke a ege 6 iTS EE ta EE Sa L oc 16 pCR Ie 19 aa sg e Th ei Been TI e Sta SIS TO D MM E Back of the remote control ventas azulmarina com www azulmarina com Install the projector according to the environment and manner the projector will be used in Arrangement Refer to the illustrations and tables below to determine screen size and projection distance The values shown in the table are calculated for a full size screen 1024x768 a Screen size diagonal b Projection distance 10 c Screen height 10 On a horizontal surface a c up e Keep a space of 30 cm or more between the sides of the projector and other objects such as walls e Consult with your dealer before a special installation such as suspending from a ceiling Sen 4 3 screen 16 D screen b Projection distance c Screen height b Pro
42. components fluorescent tubes and electronic ceramic parts e g piezoelectronic devices 3 Lead in high temperature type solders i e lead based alloys containing 85 by weight or more lead 4 Lead as an allotting element in steel containing up to 0 35 lead by weight aluminium containing up to 0 4 lead by weight and as a cooper alloy containing up to 4 lead by weight ViewSonic PJ358 iii www azulmarina com ventas azulmarina com www azulmarina com Copyright Information Copyright ViewSonic Corporation 2006 All rights reserved Macintosh and Power Macintosh are registered trademarks of Apple Computer Inc Microsoft Windows Windows NT and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries ViewSonic the three birds logo OnView ViewMatch and ViewMeter are registered trademarks of ViewSonic Corporation VESA is a registered trademark of the Video Electronics Standards Association DPMS and DDC are trademarks of VESA PS 2 VGA and XGA are registered trademarks of International Business Machines Corporation Disclaimer ViewSonic Corporation shall not be liable for technical or editorial errors or omissions contained herein nor for incidental or consequential damages resulting from furnishing this material or the performance or use of this product In the interest of continuing product improvement ViewSonic Corporation reserves the right to change pro
43. contact your dealer or service company The cooling fan is not operating Please turn the power off and allow the projector to cool down at least 20 minutes After the projector has sufficiently cooled down please make confirmation that no foreign matter has become caught in the fan etc and then turn the power on again If the same indication is displayed after the remedy please contact your dealer or service company continued on next page PJ358 62 www azulmarina com ventas azulmarina com ViewSonic www azulmarina com Regarding the indicator lamps continued POWER indicator indicator indicator eak ZUEN There is a possibility that the interior portion has become heated Please turn the power off and allow the projector to Blinking cool down at least 20 minutes After the projector has in Red sufficiently cooled down please make confirmation of Sp Lighting the following items and then turn the power on again Lighting In Red Is there blockage of the air passage aperture in Red e Is the air filter dirty e Does the peripheral temperature exceed 35 C If the same indication is displayed after the remedy please set FAN SPEED of the SERVICE item in the OPTION menu to HIGH It is time to clean the air filter Please immediately turn the power off and clean or Lighting Simultaneous change the air filter referring to the section Air Filter In Green blinking in Red After cleaning or changing
44. ctor to cool down at least 20 minutes After having confirmed the following items please turn the power ON again CHECK THE AIR FLOW e Is there blockage of the air passage aperture e Is the air filter dirty e Does the peripheral temperature exceed 35 C lf the same indication is displayed after the remedy please set FAN SPEED of the SERVICE item in the OPTION menu to HIGH REMINDER A note of precaution when cleaning the air filter TT HRS PASSED AFTER THE Please immediately turn the power off and clean or change LAST FILTER CHECK the air filter referring to the Air Filter section of this manual FILTER MAINTENANCE IS ESSENTIAL After you have cleaned or changed the air filter please be TO REMOVE WARNING MESSAGE eure to reset the filter timer RESET FILTER TIMER SEE MANUAL FURTHER INFO ViewSonic PJ358 61 www azulmarina com ventas azulmarina com www azulmarina com Regarding the indicator lamps When operation of the LAMP TEMP and POWER indicators differs from usual check and cope with it according to the following table POWER indicator indicator indicator Description Lighting In Orange Blinking In Green Lighting In Green Blinking In Orange Blinking In Red Blinking In Red or Lighting In Red Blinking In Red or Lighting In Red Blinking In Red or Lighting In Red discre tionary Lighting In Red Blinking In Red Turned discre tionary Blinki
45. duct specifications without notice Information in this document may change without notice No part of this document may be copied reproduced or transmitted by any means for any purpose without prior written permission from ViewSonic Corporation Product Registration To meet your future needs and to receive any additional product information as it becomes available please register your product on the Internet at www viewsonic com The ViewSonic Wizard CD ROM also provides an opportunity for you to print the registration form which you may mail or fax to ViewSonic For Your Records Product Name PJ358 ViewSonic LCD Projector Model Number VS11611 Document Number PJ358 1_UG_ENG Rev 1B 10 25 06 Serial Number Purchase Date Personal Identification Number PIN The lamp in this product contains mercury Please dispose of in accordance with local state or federal laws ViewSonic PJ358 iv www azulmarina com ventas azulmarina com www azulmarina com Projector PJ 358 User s Manual Operating Guide 1 Projector 2 Remote control with two AA batteries Power cord RGB cable Soft case Quick Start Guide and ViewSonic Wizard CD 7 Lens cover Rivet and Strap 3 4 5 6 Pei Pei eei eei NOTE e Keep the original packing materials for future reshipment For moving the projector be sure to use the original packing materials Use special caution for the lens part POUR NS MENEN Various sy
46. e is specified The SOURCE NAME dialog will be displayed 3 The current name will be displayed on the first line Use the AIE lt 1 gt buttons and the ENTER or INPUT button to select and enter characters The RESET button can be used to erase 1 character at a time The name can be a maximum of 16 characters SOURCE NAME 4 To change an already inserted character press the A button while the cursor is on the A N row to move the cursor to the name displayed on the first line and use the dk buttons to select character to be changed Once a character in the name is selected use the W button to move the cursor back down to the character entry area to select and enter characters as described above 5 Select J and press the ENTER or INPUT buttons when finished entering text To revert to the previous name without saving changes press the ESC or lt button and the INPUT button simultaneously ViewSonic PJ358 36 www azulmarina com ventas azulmarina com www azulmarina com PINKO Merv From the OPTION menu items shown in the table below can be performed Select an item using cursor button or ENTER button to execute the item except for the items LAMP TIME and FILTER TIME Then perform it according to the following table PICTURE IMAGE AUTO SEARCH TURN ON AUTO KEYSTONECY TURN ON INPUT AUTO ON SETUP the A V cursor buttons and press the b ae LAMP TIME FILTER TIME MY BUTTON
47. ed type e If the lamp breaks soon after the first time it is used it is possible that there are electrical problems elsewhere besides the lamp If this happens contact your local dealer or a service representative e Handle with care jolting or scratching could cause the lamp bulb to burst during use e Using the lamp for long periods of time could cause it dark not to light up or to burst When the pictures appear dark or when the color tone is poor please replace the lamp as soon as possible Do not use old used lamps this is a cause of breakage ViewSonic PJ358 58 www azulmarina com ventas azulmarina com www azulmarina com Air filter Please check and clean the air filter periodically When the indicators or a message prompts you to clean the air filter comply with it as soon as possible Replace the air filter when it is damaged or too soiled To prepare a new air filter contact ViewSonic and tell the air filter type number When you replace the lamp please replace the air filter An air filter of specified type will come together with a replacement lamp for this projector Cleaning the air filter 1 Turn the projector off and unplug the power cord Allow the projector to sufficiently cool down Use a vacuum cleaner on and around the filter cover 3 While supporting the projector with one hand use your other hand to pull the filter cover forward in the direction of the arrow Use a vacuum cleaner for t
48. em can be selected only for a video s video and component video signal e When this adjustment is too large certain degradation may appear at the frame area of the picture In such a case please adjust small Using the AE buttons adjusts the vertical position Up amp Down e This item cannot be selected for a signal from the USB STORAGE port e Over adjusting the vertical position may cause noise to appear on the screen If this V POSITION occurs please reset the vertical position to the default setting Pressing the RESET button when the V POSITION is selected will reset the V POSITION to the default setting e When this function is performed on a video signal s video signal or component video signal of 525i 480i or 625i 576i the range of this adjustment depends on the OVER SCAN setting It is not possible to adjust when the OVER SCAN is set to 10 Using the AE buttons adjusts the horizontal position Left amp Right e This item cannot be selected for a signal from the USB STORAGE port e Over adjusting the horizontal position may cause noise to appear on the screen If this H POSITION occurs please reset the horizontal position to the default setting Pressing the RESET button when the H POSITION is selected will reset the H POSITION to the default setting e When this function is performed on a video signal s video signal or component video signal the range of this adjustment depends on the OVER SCAN setting It is not possib
49. eplace the batteries If you will not use the remote control for long period remove the batteries from the remote control and store them in a safe place 1 Holding the hook part of the battery cover remove it a Align and insert the two AA batteries according to their plus and minus terminals as indicated in the remote control 3 Replace the battery cover in the direction of the arrow and snap it back into place AWARNING P amp Always handle the batteries with care and use them only as directed Improper use may result in battery explosion cracking or leakage which could result in fire injury and or pollution of the surrounding environment e Be sure to use only the batteries specified Do not use batteries of different types at the same time Do not mix a new battery with used one e Make sure the plus and minus terminals are correctly aligned when loading a battery e Keep a battery away from children and pets e Do not recharge short circuit solder or disassemble a battery e Do not allow a battery in a fire or water Keep batteries in a dark cool and dry place e If you observe a leakage of a battery wipe out the flower and then replace a battery If the flower adheres your body or clothes rinse well with water immediately e Obey the local laws on disposing the battery About the remote control signal The remote control works with the projector s remote sensor This projector has a remote sensor on the front The
50. epsc ca in Canada For more information call your dealer e If the lamp should break it will make a loud bang when it does unplug the power cord from the outlet and make sure to request a e replacement lamp from your local dealer Note that shards of glass could damage the projector s internals or cause injury during handling so please do not try to clean the projector or replace the lamp yourself Disconnect If the lamp should break it will make a loud bang when it does the plug ventilate the room well and make sure not to breathe the gas that fromthe Comes out of the projector vents or get it in your eyes or mouth power e Before replacing the lamp turn the projector off and unplug the power outlet cord then wait at least 45 minutes for the lamp to cool sufficiently Handling the lamp while hot can cause burns as well as damaging the lamp e Never unscrew except the appointed marked by an arrow screws e Do not open the lamp cover while the projector is suspended from above This is dangerous since if the lamp s bulb has broken the shards will fall out when the cover is opened In addition working in high places is dangerous so ask your local dealer to have the lamp replaced even if the bulb is not broken e Do not use the projector with the lamp cover removed At the lamp replacing make sure that the screws are screwed in firmly Loose screws could result in damage or injury e Use only the lamp of the specifi
51. ewSonic warrants its products to be free from defects in material and workmanship under normal use during the warranty period If a product proves to be defective in material or workmanship during the warranty period ViewSonic will at its sole option repair or replace the product with a like product Replacement product or parts may include remanufactured or refurbished parts or components How long the warranty is effective North and South America 3 years for all parts excluding the lamp 3 years for labor 1 year for the original lamp from the date of the first consumer purchase Europe 3 years for all parts excluding the lamp 3 years for labor 1 year for the original lamp from the date of the first consumer purchase Other regions or countries Please check with your local dealer or local ViewSonic office for the warranty information Lamp warranty subject to terms and conditions verification and approval Applies to manufacturer s installed lamp only All accessory lamps purchased separately are warranted for 90 days Who the warranty protects This warranty is valid only for the first consumer purchaser What the warranty does not cover 1 Any product on which the serial number has been defaced modified or removed 2 Damage deterioration or malfunction resulting from a Accident misuse neglect fire water lightning or other acts of nature unauthorized product modification or failure to follow instructions supplied w
52. f SECURITY item in OPTION menu MyScreen Lock continued on next page ViewSonic PJ358 35 www azulmarina com ventas azulmarina com www azulmarina com SCREEN Menu continued Description Using the AE buttons turns on off the message function TURN ON amp TURN OFF When the TURN ON is selected the following message function works AUTO IN PROGRESS while automatically adjusting NO INPUT IS DETECTED SYNC IS OUT OF RANGE Searching while searching for the input MESSAGE Detecting while an input signal is detected The indication of the input signal displayed by changing The indication of the aspect ratio displayed by changing The indication of the PICTURE MODE displayed by changing The indication of the MY MEMORY displayed by changing The indication of FREEZE and Il while freezing the screen by pressing the FREEZE button e When the TURN OFF is selected please remember if the picture is freezing Do not mistake freezing for a malfunction Each input port for this projector can have a name applied to it 1 Use the AIE buttons on the SCREEN menu to select SOURCE NAME and press the button The SOURCE NAME menu will be displayed BE NAME COMPUTER 1 NOTE PC gt 2 Use the AE buttons on the SOURCE COMPUTER 2 DESKTOP PC NAME menu to select the port to be named UR TE FC TESS and press the k button Right side of the VIDEO VTR menu is blank until a nam
53. fe place Heed all warnings Follow all instructions Do not use this equipment near water Warning To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture Clean with a soft dry cloth If further cleaning is required see Cleaning the Display in this guide for further instructions Do not block any ventilation openings Install the equipment in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other devices including amplifiers that produce heat Do not attempt to circumvent the safety provisions of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade and the third prong are provided for your safety If the plug does not fit into your outlet consult an electrician for replacement of the outlet Protect the power cord from being tread upon or pinched particularly at the plug and the point where if emerges from the equipment Be sure that the power outlet is located near the equipment so that it is easily accessible Only use attachments accessories specified by the manufacturer Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the equipment When a cart is used use caution when moving the cart equipment combination to avoid
54. he filter ventilation of the projector And clean the air filter that is set at one side of the filter cover by using a vacuum cleaner over the other side of the filter cover Please replace the air filter when it is damaged or too soiled When the air filter is set take its half moon shape cut part to the swelled part of the The air filter is set in the reverse filter cover L Ai D Put the filter unit back into the projector HZ Gua Turn the projector on and reset the filter time Air filter using the FILTER TIME item in the EASY MENU Filter cover 1 Press the MENU button to display a menu 2 Point at the FILTER TIME using the W A button then press the b button A dialog will appear 3 Press the A button to select RESET on the dialog It performs resetting the filter time NOTE Please reset the filter time only when you have cleaned or replaced the air filter for a suitable indication about the air filter e The projector may display the message such as CHECK THE AIR FLOW or turn off the projector to prevent the internal heat level rising ViewSonic PJ358 59 www azulmarina com ventas azulmarina com www azulmarina com Other care Inside of the projector In order to ensure the safe use of your projector please have it cleaned and inspected by your dealer about once every year Caring for the lens If the lens is flawed soiled or fogged it could cause deteriorat
55. he items LAMP TIME FILTER TIME LANGUAGE and SECURITY are not reset RESET amp CANCEL continued on next page ViewSonic PJ358 41 www azulmarina com ventas azulmarina com www azulmarina com OPTION Menu continued Description SECURITY This projector is equipped with security functions User registration is required before using the security functions Please contact your local dealer 1 Using Security Features 1 1 Inputting the PASSWORD 1 1 1 Use the A V buttons on the OPTION menu to select SECURITY and press the gt button The ENTER PASSWORD box will be displayed The factory default PASSWORD is 5606 This PASSWORD can be changed 1 2 Changing the PASSWORD e It is strongly recommended the factory default PASSWORD to be changed as soon as possible 1 1 2 Use the AET db buttons to enter the registered PASSWORD Move the cursor to the right side of the ENTER PASSWORD BOX and press the b button to display the SECURITY menu If an incorrect PASSWORD is input the ENTER PASSWORD BOX will be displayed again If incorrect PASSWORD is input 3 times the projector will turn off Afterwards the projector will turn off every time an incorrect PASSWORD is input 1 2 Changing the PASSWORD 1 2 1 Use the A V buttons on the SECURITY menu to select SECURITY PASSWORD CHANGE and press the b button to display the ENTER NEW PASSWORD BOX 1 2 2 Use the AIE Tb buttons to enter the new PASSWORD 1 2 3 Move
56. ich prevents the projector from being used unless a registered Code is input 3 1 Registering the PIN Code 3 1 1 Use the AE buttons on the SECURITY menu PIN LOCK to select PIN LOCK and press the b button or the ENTER button to display the PINLOCK on off menu continued on next page ViewSonic PJ358 44 www azulmarina com ventas azulmarina com www azulmarina com OPTION Menu continued Description 3 1 2 Use the A V buttons on the PIN LOCK on off menu to select TURN ON and the PIN BOX PIN BOX will be displayed Input PIN Code 3 1 3 Input a 4 part PIN Code using the A V lt A CV COMPUTER e lt gt COMPUTER STORAGE and INPUT buttons PIN BOX A CONFIRMATION BOX will appear Reenter the EEN W same PIN Code This will complete the PIN Code lt J gt AJ Cv COMPUTER e registration e If there is no key input for about 55 seconds while the PIN BOX or the CONFIRMATION BOX are displayed the menu will close If necessary repeat the process from 3 1 1 Afterwards anytime the projector is restarted after the power switch is turned off the PIN BOX will be displayed Enter the registered PIN Code The projector can be used after entering the registered PIN Code If an incorrect PIN Code is input the PIN BOX will be displayed again If an incorrect PIN Code is input 3 times the projector will turn off Afterwards the projector will turn off every time an incorrect PIN Code is input The projector will a
57. ide Focus ring Zoom ring Control panel Speaker Elevator knobs x 2 Elevator feet x 2 Lens Lens cover 0 Intake vents 1 Filter cover The air filter and intake vent are inside Exhaust vents Mu bue VIDEO port Go S VIDEO port Security slot 12 AN HoT COMPUTER IN1 port Shutdown switch 14 15 16 17 18 19 20 21 22 23 COMPUTER IN2 port E F S y A ER o USB port USB STORAGE port es a Sa le USB USB STORAGE DC 5V 0 5A AL OO OUT COMPUTER IN1 COMPUTER IN2 AUDIO OUT port H AUDIO IN port Eur a VIDEO AUDIO IN AWARNING gt HOT DO not touch around the lamp cover and the exhaust vents during use or just after use since it is too hot b Do not look into the lens or vents while the lamp is on since the strong light is not good for your eyes gt Do not handle the elevator knobs without holding the projector since the projector may drop down ACAUTION b Maintain normal ventilation to prevent the projector from heating up Do not cover block or plug up the vents Do not place anything that can stick or be sucked to the vents around the intake vents Clean the air filter periodically gt Do not use the security slot to prevent the projector from falling down since it is not designed for it b Use the shutdown switch only when the projector is not turned off by normal procedure since pushing this swit
58. ilter Please consult your dealer unit mm ViewSonic PJ358 66 www azulmarina com ventas azulmarina com www azulmarina com Customer Support For technical support or product service see the table below or contact your reseller Note You will need the product serial number T Telephone Country Region y g F Fax T 800 688 6688 United States www viewsonic com support service us viewsonic com F 909 468 1202 Canada www viewsonic com support T 866 463 4775 service ca viewsonic com United Kingdom www viewsoniceurope com uk T 0207 949 0307 So e Sege Europe Middle East Baltic coun service eu viewsoniceurope www viewsoniceurope com Contact your reseller tries and North com Africa Australia and New AUS 1800 880 818 www viewsonic com au support service au viewsonic com Zealand NZ 0800 008 822 Singapore Malay sia Thailand www viewsonic com sg support T 65 64616044 service sg viewsonic com South Africa Other T 886 2 2246 3456 l i Www viewsonic com service sd viewsonic com countries F 886 2 2249 1751 Hong Kong www hk viewsonic com support T 852 3102 2900 service hk viewsonic com www hk viewsonic com support T 853 700 303 service hk viewsonic com www viewsonic com T 080 265 9080 service kr viewsonic com ViewSonic PJ358 67 www azulmarina com ventas azulmarina com www azulmarina com Limited Warranty VIEWSONIC PROJECTOR What the warranty covers Vi
59. ion of display quality Please take care of the lens being cautious of handling Turn the projector off and unplug the power cord Allow the projector to cool sufficiently 2 After making sure that the projector is cool adequately lightly wipe the lens with a commercially available lens cleaning wipe Do not touch the lens directly with your hand Caring for the cabinet and remote control Incorrect care could have adverse influence such as discoloration peeling paint etc 1 Turn the projector off and unplug the power cord Allow the projector to cool sufficiently After making sure that the projector is cool adequately lightly wipe with gauze ora soft cloth If the projector is extremely dirty dip soft cloth in water or a neutral cleaner diluted in water and wipe lightly after wringing well Then wipe lightly with a soft dry cloth AWARNING P amp Before caring make sure the power cable is not plugged in and then allow the projector to cool sufficiently The care in a high temperature state of the projector could cause a burn and or malfunction to the projector b Never try to care for the inside of the projector personally Doing is so dangerous gt Avoid wetting the projector or inserting liquids in the projector It could result in a fire an electric shock and or malfunction to the projector e Do not put anything containing water cleaners or chemicals near the projector e Do not use aerosols or sprays
60. is function may not work e When the projector is inclined to near 30 degree or over this function may not work well e This function will be unavailable when the Transition Detector is on Using the AE buttons corrects the vertical keystone distortion Shrink the top of the image Shrink the bottom of the image e The adjustable range of this function will vary with the type of input signal For some input this function may not work well e This function will be unavailable when the Transition Detector is on continued on next page ViewSonic PJ358 31 www azulmarina com ventas azulmarina com www azulmarina com SETUP Menu continued Item Description Using the AE buttons turns off on the whisper mode NORMAL amp WHISPER e When the WHISPER is selected acoustic noise and screen brightness are reduced WHISPER Using the AE buttons switches the mode for mirror status Wl di Se MIRROR NORMAL H INVERT V INVERT H amp V INVERT If the Transition Detector is TURN ON and MIRROR status is changed Transition Detector Alarm will be displayed when projector is restarted after the power switch is turned off Using the A V buttons adjusts the volume High Low Allocates an audio port for USB STORAGE port 1 Press the Y button to begin to select 2 Use the lt gt buttons to select an Audio port for the USB STORAGE port EAO ered O USB STORAGE O AUDIO IN JK amp USB STO
61. ith the product Repair or attempted repair by anyone not authorized by ViewSonic Any damage of the product due to shipment Removal or installation of the product Causes external to the product such as electric power fluctuations or failure Use of supplies or parts not meeting ViewSonic s specifications Normal wear and tear Any other cause which does not relate to a product defect 3 Any product exhibiting a condition commonly known as image built in which results when a static image is displayed on the product for an extended period of time 4 Removal installation and set up service charges oer p pn P How to get service 1 For information about receiving service under warranty contact ViewSonic Customer Support Please refer to Customer Support page You will need to provide your product s serial number ViewSonic PJ358 68 www azulmarina com ventas azulmarina com www azulmarina com 2 To obtain warranted service you will be required to provide a the original dated sales slip b your name c your address d a description of the problem and e the serial number of the product 3 Take or ship the product freight prepaid in the original container to an authorized ViewSonic service center or ViewSonic 4 For additional information or the name of the nearest ViewSonic service center contact ViewSonic 5 For applicable models with the PIN code security feature only This projector contains a perso
62. jection distance c Screen height wn do SE EE posta EEE EE EE 1 3 50115 61 11 4 65 2 BUS IS 61119 73 13 5 78 3 18 71 122 85115 6 91 3 80 2 0 reife taser ar 7 105 at 90 2 3 2 3 91 28 110 20 8 118 46 2 2 6 102 3 1 122 22 9 131 51 5 6 222 6 8 267 5 2 243 96 300 7 6 7 8 306 9 3 368 65 26 392 154 8 5 334 10 2 400 8 3 365 144 ViewSonic PJ358 6 www azulmarina com ventas azulmarina com www azulmarina com AWARNING P amp Place the projector in a stable horizontal position If the projector falls or is knocked over it could cause injury and or damage to the projector Using a damaged projector could then result in fire and or electric shock e Do not place the projector on an unstable slanted or vibrational surface such as a wobbly or inclined stand e Do not place the projector on its side front or rear position e Consult with your dealer before a special installation such as suspending from a ceiling b Place the projector in a cool place and ensure that there is sufficient ventilation The high temperature of the projector could cause fire burns and or malfunction of the projector e Do not stop up block or otherwise cover the projector s vents e Keep a space of 30 cm or more between the sides of the projector and other objects such as walls e Do not place the projector on metallic thing or anything weak i
63. k the VIDEO port Searching an input signal Press the SEARCH button on the remote control SEARCH The projector will start to check its input ports in order to find any input signals When an input is found the projector will stop searching and display the image If no signal is found the projector will return to the state selected before the operation COMPUTER INI gt COMPUTER IN2 VIDEO S VIDEO USB STORAGE i I 7 e Selecting the USB STORAGE port displays the THUMBNAIL menu For more information please see the USB STORAGE Selecting an aspect ratio 1 Press the ASPECT button on the remote control ASPECT Each time you press the button the projector switches the mode for aspect ratio in turn ex BB once H O For a PC signal or a signal from the USB STORAGE CRO G NORMAL gt 4 3 gt 16 9 gt SMALL IG Ol YS em ww wb O For a video signal s video signal or component video signal 4 3 gt 16 9 gt 14 9 gt SMALL ee d O For no signal 4 3 fixed e The ASPECT button does not work when no proper signal is inputted e The NORMAL mode keeps the original aspect ratio setting e Performing the automatic adjustment initializes the aspect ratio setting ViewSonic PJ358 15 www azulmarina com ventas azulmarina com www azulmarina com Adjusting the projector s elevator When the place to put the projector is slightly uneven to the left or right use the elevator feet to place the projector horiz
64. le to adjust when the OVER SCAN is set to 10 continued on next page ViewSonic PJ358 26 www azulmarina com ventas azulmarina com www azulmarina com IMAGE Menu continued Hem Description H PHASE AUTO ADJUST EXECUTE Using the AIE buttons adjusts the horizontal phase to eliminate flicker Right gt Left e This item can be selected only for a computer signal or component video signal Using the A V buttons adjusts the horizontal size Large Small e This item can be selected only for a computer signal e When this adjustment is excessive the picture may not be displayed correctly In such a case please reset the adjustment by pressing the RESET button during this operation Selecting this item performs the automatic adjustment feature For a PC signal The vertical position the horizontal position the horizontal phase and the horizontal size will be automatically adjusted And the aspect ratio will be automatically set to the default Make sure that the application window is set to its maximum size prior to attempting to use this feature A dark picture may still be incorrectly adjusted Use a bright picture when adjusting For a signal from the USB STORAGE The aspect ratio will be automatically set to the default For a video signal s video signal or component video signal The video format best suited for the respective input signal will be selected automatically This function is available
65. lso turn off if there is no key input for about 5 minutes while the PIN BOX is displayed This function will activate only when the projector is started after the power switch was turned off e Please do not forget your PIN Code 3 2 Turning Off the PIN LOCK Function 3 2 1 Follow the procedure in 3 1 1 to display the PIN LOCK on off menu Use the A V buttons to select TURN OFF and the PIN BOX will be displayed Enter the registered PIN Code to turn the PIN LOCK function off If an incorrect PASSWORD is entered the menu will close SECURITY continued 3 3 If you have forgotten your PIN Code 3 3 1 While the PIN BOX is displayed press and erren hold the RESET button for three seconds or press and hold the INPUT and b buttons for ZE SE E three seconds The 10 digit Inquiring Code will be displayed e If there is no key input for about 5 minutes while the Inquiring Code is displayed the projector will turn off 3 3 2 Contact your dealer with the 10 digit Inquiring Code Your PASSWORD will be sent after your user registration information is confirmed continued on next page ViewSonic PJ358 45 www azulmarina com ventas azulmarina com www azulmarina com OPTION Menu continued Description 4 Using the Transition Detector Function While the Transition Detector function is ON when power switch is started to supply to the projector it might react as below e Transition Detector alarm shown below might
66. mbols are used in this manual The meanings of these symbols are described below AWARNING This symbol indicates information that if ignored could possibly result in personal injury or even death due to incorrect handling ACAUTION This symbol indicates information that if ignored could possibly result in personal injury or physical damage due to incorrect handling Please refer to the pages written following this symbol NOTE e The information in this manual is subject to change without notice e The manufacturer assumes no responsibility for any errors that may appear in this manual e The reproduction transfer or copy of all or any part of this document is not permitted without express written consent Trademark acknowledgment e Mac is registered trademarks of Apple Computer Inc e VESA and SVGA are trademarks of the Video Electronics Standard Association e Windows is a registered trademark of Microsoft Corporation All other trademarks are the properties of their respective owners ViewSonic PJ358 1 www azulmarina com ventas azulmarina com About this manual 1 Content Z de Farir fe 2 Projector features 3 Dreparations aana 3 Contents of package 3 Fastening the lens cover 3 Replacing the filter cover for bottom up use Part names ProjectOW GE eze zra dE B azo 4 Control panel onnon annann anna 5 Remote control 5 Setting UP erra dt Rye ue
67. mena that may be easy to be mistaken for machine defects About the phenomenon confused with a machine defect check and cope with it according to the following table Reference Phenomenon Cases not involving a machine defect page The electrical power cord is not plugged in Correctly connect the power cord The main power source has been interrupted during operation such as by a power outage blackout etc Please disconnect the power plug from the power outlet and allow the projector to cool down at least 10 minutes Power does not then turn the power on again cee EN Either there is no lamp and or lamp cover or either of these has not been properly fixed Please turn the power off and disconnect the power plug from the power outlet and allow the projector to cool down at least 45 minutes After the projector has sufficiently cooled down please make confirmation of the attachment state of the lamp and lamp cover and then turn the power on again Neither sounds Signal source does not correctly work nor pictures are Correctly set up the signal source device by referring to the outputted manual of the source device The MUTE function is working Restore the sound pressing the MUTE or VOLUME button Sound does not on the remote control come out The volume is adjusted to an extremely low level Adjust the volume to a higher level using the menu function or the remote control The AUDIO setting is not cor
68. mp e For the lamp replacement see the section Lamp LAMP TIME The filter time is the time counted after the last resetting It is shown in the OPTION menu as the usage time of the air filter Pressing the RESET button or the button displays a dialog To reset the filter time select the RESET using the A button RESET CANCEL e Please reset the filter time only when you have cleaned or replaced the air filter for a suitable indication about the air filter e For the air filter cleaning see the section Air filter FILTER TIME continued on next page ViewSonic PJ358 38 www azulmarina com ventas azulmarina com www azulmarina com OPTION Menu continued Description This item is to assign one of the following function to MY BUTTON 1 and 2 on the remote control Choose 1 or 2 on the MY BUTTON menu using the ak button first Then using the AE buttons sets one of the following functions to the chosen button e COMPUTER Sets port to COMPUTER IN e COMPUTER2 Sets port to COMPUTER IN2 e USB STORAGE Sets port to USB STORAGE e S VIDEO Sets port to S VIDEO e VIDEO Sets port to VIDEO e INFORMATION Displays a dialog of INPUT INFORMATION e AUTO KEYSTONE HN EXECUTE Performs automatic keystone distortion correction e MY MEMORY Loads one of adjustment data stored MY BUTTON When the current adjustment When no data is saved is not saved to memory a in memory a dialog is dialog is displayed
69. n the projector so that START setting can be selected Change START setting range from 1 to 999 using A and V buttons Get out from the status that START setting is selectable by pushing ENTER button on the remote control or INPUT ENTER button on the projector Specify and select image file number in thumbnail display as finishing number for SLIDE SHOW Select STOP using A E lt and gt buttons then push ENTER button on the remote control or INPUT ENTER button on the projector so that STOP setting can be selected Change STOP setting range from 1 to 999 using A and V buttons Get out from the status that STOP setting is selectable by pushing ENTER button on the remote control or INPUT ENTER button on the projector She and select page forwarding interval for SLIDE SHOW Select INTERVAL using A V lt and gt buttons then push ENTER button on the remote control or INPUT ENTER button on the projector so that INTERVAL setting can be selected INTERVAL Change INTERVAL setting range from 1 to 999 seconds using A and Y buttons Get out from the status that INTERVAL setting is selectable by pushing ENTER button on the remote control or INPUT ENTER button on the projector continued on next page ViewSonic PJ358 53 www azulmarina com ventas azulmarina com www azulmarina com Playing Slide show continued SLIDE SHOW items continued Description Select SL
70. n heat e Do not place the projector on carpet cushions or bedding e Do not place the projector in direct sunlight or near hot objects such as heaters e Do not anything near the projector lens or vents or on top of the projector e Do not place anything that may be sucked into or stick to the vents on the bottom of the projector This projector has some intake vents also on the bottom gt Do not place the projector anyplace where it may get wet Getting the projector wet or inserting liquid into the projector could cause fire electric shock and or malfunction of the projector e Do not place the projector in a bathroom or the outdoors e Do not place anything containing liquid near the projector ACAUTION PAvoid placing the projector in smoky humid or dusty place Placing the projector in such places could cause fire electric shock and or malfunction of the projector e Do not place the projector near humidifiers smoking spaces or a kitchen b Position the projector to prevent light from directly hitting the projector s remote sensor ViewSonic PJ358 www azulmarina com ventas azulmarina com www azulmarina com Connecting your devices Be sure to read the manuals for devices before connecting them to the projector Make sure that all the devices are suitable to be connected with this product and prepare the cables required to connect Please refer to the following illustrations to connect them Speakers o0
71. n loading data This is not malfunction e The LOAD functions can be also performed by the MY MEMORY button which can be set by the MY BUTTON item in OPTION menu SAVE1 SAVE2 SAVE3 SAVE4 Performing a SAVE function saves the current adjustment data into the memory linked in the number included in the function s name e Remember that the current data being stored of a memory will be lost by saving a new data into the memory ViewSonic PJ358 25 www azulmarina com ventas azulmarina com www azulmarina com IMAGIS MISE From the IMAGE menu items shown in the table below can be performed Select an item using the AE cursor buttons and press h POSITION the gt cursor button or ENTER button to execute the item H SIZE e Then perform it according to the following table EASY MENU AUTO ADJUST EXECUTE Description Using the A V buttons switches the mode for aspect ratio For a PC signal or a signal from the USB STORAGE NORMAL d 4 3 16 9 amp SMALL dre __ _ _ 4 For a Video signal s video signal or component video signal 4 3 16 9 14 9 SMALL W A For no signal 4 3 fixed e This item can be selected only for a proper signal e The NORMAL mode keeps the original aspect ratio setting e Performing the automatic adjustment initializes the aspect ratio setting ASPECT Using the AE buttons adjusts the over scan ratio Large It reduces picture lt Small It magnifies picture OVER SCAN e This it
72. nal identification number PIN that restricts access to authorized users If you forget to record the PIN code in the User Guide with your Serial Number you will have to send in the unit for service so the code can be reset However if you register your product serial number with ViewSonic along with your PIN code it will be retained on file with your registration should you need it in the future Limitation of implied warranties There are no warranties express or implied which extend beyond the description contained herein including the implied warranty of merchantability and fitness for a particular purpose Exclusion of damages ViewSonic s liability is limited to the cost of repair or replacement of the product ViewSonic shall not be liable for 1 Damage to other property caused by any defects in the product damaged based upon inconvenience loss of use of the product loss of time loss of profits loss of business opportunity loss of goodwill interference with business relationships or other commercil loss even if advised of the possibility of such damages 2 Any other damages whether incidental consequential or otherwise 3 Any claim against the customer by other party Effect of state law This warranty gives you specific legal rights and you may also have other rights which vary from state to state Some states do not allow limitations on implied warranties and or do not allow the exclusion of incidental or c
73. ng In Red The projector is in a standby state Please refer to the section Power on off Turned Turned The projector is warming up off off Please wait Turned Turned The projector is in an on state off off Ordinary operations may be performed Turned Turned The projector is cooling down off off Please wait The projector is cooling down A certain error has been detected Please wait until the POWER indicator finishes blinking and then perform the proper measure using the item descriptions below The lamp does not light and there is a possibility that interior portion has become heated Please turn the power off and allow the projector to cool down at least 20 minutes After the projector has sufficiently cooled down please make confirmation of the following items and then turn the power on again e Is there blockage of the air passage aperture e Is the air filter dirty e Does the peripheral temperature exceed 35 C If the same indication is displayed after the remedy please change the lamp referring to the section Lamp The lamp cover has not been properly fixed Please turn the power off and allow the projector to cool down at least 45 minutes After the projector has sufficiently cooled down please make confirmation of the attachment state of the lamp cover After performing any needed maintenance turn the power on again If the same indication is displayed after the remedy please
74. nt at the Go to Advanced Menu in the menu using the TIA button then press the b button 3 Point at the OPTION in the left column of the menu using the V A button then press the b button 4 Point at the LAMP TIME using the EIA button then press the b button A dialog will appear 5 Press the A button to select RESET on the dialog It performs resetting the lamp time NOTE Please reset the lamp time only when you have replaced the lamp for a suitable indication about the lamp ViewSonic PJ358 57 www azulmarina com ventas azulmarina com www azulmarina com Lamp continued Lamp warning A HIGH VOLTAGE A HIGH TEMPERATURE HIGH PRESSURE AWARNING gt The projector uses a high pressure mercury glass lamp The lamp can break with a loud bang or burn out if jolted or scratched handled while hot or worn over time Note that each lamp has a different lifetime and some may burst or burn out soon after you start using them In addition when the bulb bursts it is possible for shards of glass to fly into the lamp housing and for gas containing mercury to escape from the projector s vent holes gt About disposal of a lamp This product contains a mercury lamp do not put it ina trash Dispose of it in accordance with environmental laws e For lamp recycling go to www lamprecycle org in the US e For product disposal contact your local government agency or www eiae org in the US or www
75. o soon could shorten the lifetime of some consumable parts of the projector NOTE e Please power on the projector prior to the connected devices Power off the projector after all of connected devices are powered off e This projector has the function that can make the projector automatically turn on off Please refer to the AUTO ON and AUTO OFF items of the OPTION menu e Use the shutdown switch only when the projector is not turned off by normal procedure ViewSonic PJ358 13 www azulmarina com ventas azulmarina com www azulmarina com perating VOLUME Adjusting the volume 1 Press the VOLUME button on the remote control A dialog will appear on the screen to aid you in adjusting the volume Use the A V cursor buttons to adjust the volume To close the dialog and complete the operation press the VOLUME button again Even if you do not do anything the dialog will automatically disappear after a few seconds e When X is selected for the AUDIO item of the SETUP menu the volume adjustment is disable Temporarily muting the sound Press the MUTE button on the remote control Adialog will appear on the screen indicating that you have muted the sound To restore the sound press the MUTE or VOLUME button Even if you do not do anything the dialog will automatically disappear after a few seconds e When X is selected for the AUDIO item of the SETUP menu the volume adjustment is disable Selecting an input signal 1 Pres
76. ojector to be controlled should be set to the same mode as the remote control Using as a simple PC mouse amp keyboard The enclosed remote control works as a simple mouse and keyboard of the PC when the projector s USB port B type connects with the PC s mouse port via a mouse cable 1 HOME key Press the HOME button SO 2 END key Press the END button 3 PAGE UP key Press the PAGE UP button 4 PAGE DOWN key Press the PAGE DOWN button 5 Mouse left button Press the ENTER button 6 Move pointer Use the cursor buttons A V lt and P 7 ESC key Press the ESC button 8 Mouse right button Press the RESET button NOTE e When the simple mouse amp keyboard function of this product does not work correctly please check the following When the mouse cable connects this projector with a PC having a built in pointing device e g track ball like a notebook PC open BIOS setup menu then select the external mouse and disable the built in pointing device because the built in pointing device may have priority to this function Windows 95 OSR 2 1 or higher is required for this function And also this function may not work depending on the PC s configurations and mouse drivers You cannot do things like press two buttons at once for instance pressing two buttons at the same time to move the mouse pointer diagonally This function is activated only when the projector is working properly This function
77. on does not work for a signal from the USB STORAGE port e When this function is performed on a video signal s video signal or component video signal some image such as an extra line may appear at outside of the picture e When this function is performed on a video signal s video signal or component video signal the range of this adjustment depends on the OVER SCAN in the IMAGE menu setting It is not possible to adjust when the OVER SCAN is set to 10 ViewSonic PJ358 17 www azulmarina com ventas azulmarina com POSITION www azulmarina com Correcting the keystone distortions Press the KEYSTONE button on the remote control Adialog KEYSTONE will appear on the screen to aid you in correcting the distortion Use the AE cursor buttons to select the AUTO or MANUAL Operation and press the k button to perform the following 1 The AUTO executes automatic vertical keystone correction 2 The MANUAL displays a dialog for keystone correction Use the AE buttons for adjustment To close the dialog and complete this operation press the KEYSTONE button again Even if you do not do anything the dialog will automatically disappear after a few seconds e The adjustable range of this correction will vary among inputs For some input this function may not work well e When V INVERT or H amp V INVERT is selected to the MIRROR item in the SETUP menu if the projector screen is inclined or angled downward this function may not wo
78. onsequential damages so the above limitations and exclusions may not apply to you Sales outside the U S A and Canada For warranty information and service on ViewSonic products sold outside of the U S A and Canada contact ViewSonic or your local ViewSonic dealer The warranty period for this product in mainland China Hong Kong Macao and Taiwan Excluded is subject to the terms and conditions of the Maintenance Guarantee Card 4 3 Projector Warranty PRJ_LW083 Rev 1a 06 30 06 ViewSonic PJ358 69 www azulmarina com ventas azulmarina com www azulmarina com amp oF a ViewSonic ventas azulmarina com
79. ontally Using the feet can also tilt the projector in order to project at tz a suitable angle to the screen elevating the front side of the IZ p projector within 12 degrees This projector has 2 elevator feet and 2 elevator knobs An elevator foot is adjustable while pulling up the elevator knob on the same side as it Holding the projector pull the elevator knobs up to loose the elevator feet Position the front side of the projector to the desired height Release the elevator knobs in order to lock the elevator feet After making sure that the elevator feet are locked put the projector gently If necessary the elevator feet can be manually twisted to make more precise adjustments Hold the projector when twisting the feet Bi dita Ai N amp To loose an elevator foot pull up the l l elevator knob on the same side as it To finely adjust twist the foot Adjusting the zoom and focus Focus ring Zoom ring 1 Use the zoom ring to adjust the screen size 2 Use the focus ring to focus the picture ViewSonic PJ358 16 www azulmarina com ventas azulmarina com www azulmarina com Using the automatic adjustment feature Press the AUTO button on the remote control Pressing this button performs the following O Fora PC signal The vertical position the horizontal position the horizontal phase and the horizontal size will be automatically adjusted And the aspect ratio will be automatically set to default Make sure
80. ortion may appear Using the A V buttons adjusts the strength of whole color Strong d Weak e This item can be selected only for a video signal s video or component video signal Using the AE buttons adjusts the tint Greenish amp Reddish e This item can be selected only for a video signal s video or component video signal Using the A V buttons adjusts the sharpness Strong d Weak e There may be some noise and or the screen may flicker for a moment when an adjustment is made This is not a malfunction continued on next page ViewSonic PJ358 24 www azulmarina com ventas azulmarina com www azulmarina com PICTURE Menu continued Description This projector has 4 memories for adjustment data for all the items of the PICTURE menu Selecting a function using the A V buttons and pressing the b or ENTER button performs each function nee LOAD2 LOAD3 e LOAD4 SAVE4 SAVE3 GAN EZ SAVE LOAD1 LOAD2 LOAD3 LOAD4 Performing a LOAD function loads the data from the memory linked in the number included in the function s name and adjusts the picture automatically depending on the data e The LOAD functions whose linked memory has no data are MY MEMORY skipped e Remember that the current adjusted condition will be lost by loading data If you want to keep the current adjustment please save it before performing a LOAD function e There may be some noise and the screen may flicker for a moment whe
81. p has finite product life Using the lamp for long periods of time could cause the pictures darker or the color tone poor Note that each lamp has a different lifetime and some may burst or burn out soon after you start using them Preparation of a new lamp and early replacement are recommended To prepare a new lamp contact your dealer and tell the lamp type number Type number RLC 027 Replacing the lamp The lamp cover 1 Turn the projector off and unplug the power cord Allow the projector to cool for at least 45 minutes d Prepare a new lamp If the projector is mounted on a ceiling or if the lamp has broken also ask the dealer to replace the lamp OU a edi 4 aa In case of replacement by yourself 3 Loosen the screw marked by arrow of the lamp cover and then slide the lamp cover to the side to remove it 4 Loosen the 2 screws marked by arrow of the lamp and slowly pick up the lamp by the handle lt may make it easy to take the lamp out slightly toward the control panel of the projector 5 Insert the new lamp and retighten firmly the 2 screws of the lamp that are loosened in the previous process to lock it in place Tighten the screw first then screw 6 Slide the lamp cover back in place and firmly fasten the screw of the lamp cover 7 Turn the projector on and reset the lamp time using the LAMP TIME item in the OPTION menu 1 Press the MENU button to display a menu 2 Poi
82. po 0 the item didi ea dedo TT Lee wei b ENG E Go to Advanced Menu In the Advanced MENU EASY MENU Advanced MENU Use the AE cursor buttons to select a menu If you want to change it to the EASY MENU select the EASY MENU Then press the cursor button or the ENTER button to select an item The lower layer menu of the selected item will appear Use the AE cursor buttons to select an item to operate Then press the b cursor button or the ENTER button to progress The operation menu of the selected item will appear 4 Use the AE cursor buttons to operate the item Some functions cannot be performed when a certain input port is selected or when a certain input signal is displayed When you want to reset the operation press the RESET button on the remote control during the operation Note that some items ex LANGUAGE H PHASE VOLUME cannot be reset In the Advanced Menu when you want to return to the previous display press the lt cursor button or the ESC button on the remote control Press the MENU button on the remote control again to close the menu and complete this operation Even if you do not do anything the dialog will automatically disappear after about 10 seconds ViewSonic PJ358 20 www azulmarina com ventas azulmarina com www azulmarina com EASY MENU COMPUTER1 JASMENO GES E3 P AUTO KEYSTONE CY EI KEYSTONE From the EASY MENU items shown in the table below can PICTURE MODE CUSTOM be performed
83. produced In combinations of file format and audio format described in the above lists some files can not be reproduced e USB STORAGE USB1 1 compliant USB storage media Mass Storage class can be used Some USB memories may not work correctly Security USB memory is not supported It is strongly recommended to use AC Power Adaptor with USB Hard Disc It may be happened that movie files or sound files cannot be reproduced properly if USB storage does not have enough access speed The following formats are recommended for USB storage USB memory FAT12 FAT16 FAT32 NTFS format is not supported USB hard disk FAT12 FAT16 FAT32 NTFS format is not supported Displaying Thumbnail Menu 1 Save image files in a USB storage Insert the USB storage into USB STORAGE port on the projector 2 Change input port for the projector to USB STORAGE using COMPUTER STORAGE button on the remote control or INPUT ENTER button on the projector so that Thumbnail menu below is appeared on screen 3 On Thumbnail menu the following features are supported Projector Control Have Easy Advanced Menu on screen to control the projector or change the input port to S VIDEO Thumbnail display Display many stored images in USB storage at once Slide show Switch images with set intervals Display in full screen Display one still picture or moving picture in full screen It is not in Thumbnail menu ViewSonic PJ358 4
84. rd reader having multiple slots for memory card is used Pictures in multiple memories cannot be seen at the same time e The OSD message No Media is displayed if there is no memory card with USB card reader e During blinking LED on USB card reader which indicates the access to the reader or displaying Media loading do not turn the projector into the power off standby mode nor remove insert USB cable and memory card e Following message might appear when projector input port is changed to USB STORAGE ViewSonic PJ358 49 www azulmarina com ventas azulmarina com www azulmarina com Displaying Thumbnail Menu continued Message Description No Media USB storage is not inserted into USB STORAGE slot on the projector This is an alarm message that USB storage inserted into a USB STORAGE slot on the projector is broken This is an alarm message that USB storage inserted into Bad format USB STORAGE slot on the projector has a noncompliant format Loading files in the USB storage inserted into USB Media loading STORAGE slot on the projector Please wait for a while Preparation of thumbnail display for the USB storage Ready inserted into USB STORAGE slot on the projector has been completed Please wait for a while more e Do not use this function other than private purposes It might infringe copyright laws e Back up all of the data in the memory card in case any data are lost due to unexpected accident
85. rect 30 Correctly set the AUDIO in the SETUP menu The lens cover is attached 13 No pictures are Remove the lens cover displayed The signal cables are not correctly connected Correctly connect the connection cables continued on next page ViewSonic PJ358 64 www azulmarina com ventas azulmarina com www azulmarina com Phenomena that may be easy to be mistaken for machine defects continued Reference Phenomenon Cases not involving a machine defect page The brightness is adjusted to an extremely low level Adjust BRIGHTNESS to a higher level using the menu function or the remote control No pictures are The computer cannot detect the projector as a plug displayed and play monitor continued Make sure that the computer can detect a plug and play monitor using another plug and play monitor The BLANK screen is displayed i Press the BLANK button on the remote control Video screen The FREEZE function is working display freezes Press the FREEZE button to restore the screen to normal Color settings are not correctly adjusted Colors have a Perform picture adjustments by changing the COLOR faded out TEMP COLOR TINT and or COLOR SPACE settings appearance or using the menu functions Color toneis COLOR SPACE setting is not suitable poor Change the COLOR SPACE setting to AUTO RGB SMPTE240 REC709 or REC601 The brightness and or contrast are adjusted to an extremely low level Adjust
86. rk correctly e When the zoom adjustment is set to the TELE telephoto focus the automatic keystone distortion correction may be excessive This function should be used when the zoom adjustment Is set to the full WIDE wide angle focus whenever possible e When the projector is placed on the level about 0 the automatic keystone distortion correction may not work e When the projector is inclined to near 30 degree or over this function may not work well e This function will be unavailable when Transition Detector is on Using the magnify feature 1 Press the ON button of MAGNIFY on the remote control MAGNIFY The MAGNIFY indication will appear on the screen although ON OFF the indication will disappear in several seconds with no operation and the projector will go into the MAGNIFY mode 2 Use the AT cursor buttons to adjust the zoom level To move the zoom area press the POSITION button in the MAGNIFY mode then use the AT TZUK cursor buttons to move the area And to finalize the zoom area press the POSITION button again To exit from the MAGNIFY mode and restore the screen to normal press the OFF button of MAGNIFY on the remote control e The projector automatically exits from the MAGNIFY mode when the input signal is changed or when the display condition is changed e Although in the MAGNIFY mode the keystone distortion condition may vary it will be restored when the projector exits from the MAGNIFY mode
87. s between 1st and 12th after move Select Page Up using A V lt and b buttons then push ENTER button on the remote control or INPUT ENTER button on the projector Page Up key on remote also can be used Move to following thumbnail display page When current thumbnail display shows image files between 1st and 12th it shows image files between 13th and 24th after move Page Down Select Page Down using A V lt and gt buttons then push ENTER button on the remote control or INPUT ENTER button on the projector Page Down button on remote also can be used ViewSonic PJ358 51 www azulmarina com ventas azulmarina com www azulmarina com Displaying Thumbnail image continued NOTE 3 e Up to 999 files can be displayed e Files are sorted in the following order 1 Symbols 2 Numbers 3 Characters e File name can be displayed up to 16 characters including file extension e The characters of following languages can be used for file name If other languages are used the file name is not displayed properly but the content can be displayed English French German Spanish Italian Norwegian Dutch Portuguese Swedish Russian Finnish Polish and Turkish e Folders in USB storage can be recognized up to 3 layers The priority of thumbnail display for image files is as follows A Current directory A File display priority in folder A gt B gt C gt D gt E gt F B Folder B Folder G Cannot be displayed because
88. s on the SECURITY menu to select Transition Detector and press the b or the ENTER button to display the Transition Detector on off menu 4 2 2 Use the A V buttons on the Transition TRANSITION DETECTOR Detector on off menu to select TURN ON BIEI The ENTER PASSWORD BOX small will be displayed OIT ISU 4 2 3 Use the AEK buttons to enter a TRANSITION DETECTOR PASSWORD Move the cursor to the right side of CHECK PASSWORD the ENTER PASSWORD BOX small and press 00 0 the b button to display the CHECK PASSWORD QUIT NEXT BOX enter the same PASSWORD again 4 2 4 Move the cursor to the right side of the TRANSITION DETECTOR CHECK PASSWORD BOX and press the COMPLETE b button to display the PASSWORD for 000 0 about 20 seconds please make note of the gt PASSWORD during this time EE Pressing the ENTER button will return to the Transition Detector on off menu e Please do not forget your Transition Detector PASSWORD lt lt TRANSITION DETECTOR ON gt gt continued on next page ViewSonic PJ358 46 www azulmarina com ventas azulmarina com www azulmarina com OPTION Menu continued Description 4 3 Setting the Transition Detector off 4 3 1 Follow the procedure in 4 1 1 to display the Transition Detector on off menu 4 3 2 Select TURN OFF to display the ENTER PASSWORD BOX large Enter the registered PASSWORD and the screen will return to the Transition Detector on off menu If an incorrect PASSWORD is input
89. s the INPUT ENTER button on the projector Each time you press the button the projector switches its input port as below COMPUTER IN1 gt COMPUTER IN2 VIDEO S VIDEO USB STORAGE ed Di f Press the COMPUTER STORAGE button on the COMPUTER remote control STORAGE Each time you press the button the projector switches its input port as below LST IER IN1 gt COMPUTER IN2 gt USB aS a e If the COMPUTER STORAGE button is pushed to switch from a signal from the VIDEO or S VIDEO port when TURN ON is selected for the AUTO SEARCH item in the OPTION menu the projector will check the COMPUTER IN1 port first If no input is detected at the port the projector will check other port in above order e Selecting the USB STORAGE port displays the THUMBNAIL menu For more information please see the USB STORAGE continued on next page ViewSonic PJ358 14 www azulmarina com ventas azulmarina com a www azulmarina com Selecting an input signal continued 1 Press the VIDEO button on the remote control Each time you press the button the projector switches its input port as below S VIDEO lt gt VIDEO e f the VIDEO button is pushed to switch from a signal from the COMPUTER IN1 COMPUTER IN2 or USB STORAGE port when TURN ON is selected for the AUTO SEARCH item in the OPTION menu the projector will check the S VIDEO port first If ee no input is detected at the port the projector will chec
90. s to move a cursor to THUMBNAIL item in Thumbnail menu Push ENTER button on the remote control or INPUT ENTER button on the projector to decide it Thumbnail Display Menu dee gt Pu_controL MENU Selected Image T abcdefgh 2 abcdefgh 3 abcdefgh THUMBNAIL e D d N Tire IMAGE All A Page Up E Page Down A b AE E 4 abcdefgh 5 abcdefgh 6 abcdefgh N gt d e gt SLIDE SHON PLAY START 1 STOP 999 INTERVAL 123s rro E ba By A J 7 abcdefgh 8 abcdefgh 9 abcdefgh Thumbnail images up to 12 images ODE ONE TIME SCREEN EFFECT 1 J J 10 abcdefgh 11 abcdefgh 12 abcdefgh SCH SELECT ENTER ENTER Thumbnail Menu THUMBNAIL items Description Select image files to display as thumbnail 1 Select IMAGE using A V lt and gt buttons then push ENTER button on the remote control or INPUT ENTER button on the projector so that IMAGE setting can be selected 2 Change IMAGE setting using A and Y buttons ALL Display all STILL PICTURE Display still picture only d d MOTION PICTURE Display motion picture only 3 Get out from the status that IMAGE setting is selectable by pushing ENTER button on the remote control or INPUT ENTER button on the projector Move to previous thumbnail display page When current thumbnail display shows image files between 13th and 24th it shows image file
91. splay the PASSWORD for COMPLETE about 20 seconds please make note of the 000 0 PASSWORD during this time Pressing the ENTER button will return to MyScreen eme PASS WORD on off menu When a PASSWORD is set for MyScreen e The MyScreen registration function and menu will be unavailable e The MyScreen Lock function and menu will be unavailable e The START UP setting will be locked on MyScreen and the menu will be unavailable Turning the MyScreen PASSWORD off will allow normal operation of both functions e Please do not forget your MyScreen PASSWORD 2 3 Turning the PASSWORD off 2 3 1 Follow the procedure in 2 1 1 to display the MyScreen PASSWORD on off menu 2 3 2 Select TURN OFF to display the ENTER PASSWORD BOX large Enter the registered PASSWORD and the screen will return to the SECURITY MyScreen on off menu continued If an incorrect PASSWORD is input the menu will close If necessary repeat the process from 2 3 1 2 4 If you have forgotten your PASSWORD 2 4 1 Follow the procedure in 2 1 1 to display the MyScreen PASSWORD on off menu 2 4 2 Select TURN OFF to display the ENTER tree PASSWORD BOX large The 10 digit ENTER PASSWORD Inquiring Code will be displayed inside the Inquiring Code 0123456789 a BOX d DIE 2 4 3 Contact your dealer with the 10 digit Inquiring Code Your PASSWORD will be sent after your user registration information is confirmed 3 Using the PIN LOCK Function PIN LOCK is a function wh
92. the air filter please be sure to reset the filter timer After the remedy reset the power to ON There is a possibility that the interior portion has become overcooled Please use the unit within the usage temperature parameters 5 C to 35 C After the treatment reset the power to ON Lighting Alternative In Green blinking in Red NOTE When the interior portion has become overheated for safety purposes the projector is automatically shut down and the indicator lamps may also be turned off In such a case disconnect the power cord and wait at least 45 minutes After the projector has sufficiently cooled down please make confirmation of the attachment state of the lamp and lamp cover and then turn the power on again Shutting the projector down Only when the projector can not be turned off by usual CED O EO procedure please push the shutdown switch using a Som pin or similar and disconnect the power plug from the Shutdown switch power outlet Before turning it on again wait at least 10 minutes to make the projector cool down enough Hu MU Geht Resetting all settings When it is hard to correct some wrong settings the FACTORY RESET function of the SERVICE item in the OPTION menu can reset all settings except LANGUAGE FILTER TIME LAMP TIME FILTER MESSAGE and etc to the factory default ViewSonic PJ358 63 www azulmarina com ventas azulmarina com www azulmarina com Pheno
93. the table below can be performed ue etz o Select an item using the AIE cursor buttons and press the seue color rew gei SCREEN COLOR gt cursor button or ENTER button to execute the item Then on um EASY MENU SHARPNESS perform it according to the following table WY MEMORY ege Item Description Using the AE buttons adjusts the brightness BRIGHTNESS Light Dark Using the AE buttons adjusts the contrast Ge Al Strong d Weak Using the A V buttons switches the gamma mode 1 DEFAULT 1 CUSTOM 2 DEFAULT amp 2 CUSTOM 3 DEFAULT 5 CUSTOM 5 DEFAULT 4 CUSTOM 4 DEFAULT 3 CUSTOM To adjust CUSTOM Selecting a mode whose name includes CUSTOM and then pressing the b button or the ENTER button displays a dialog to aid you in adjusting the mode This function is useful when you want to change the brightness of particular tones Choose an item using the lt gt buttons and adjust the level using the A V buttons You can display a test pattern for checking the effect of your adjustment by pressing the ENTER button Each time you press the ENTER button the pattern changes as below No pattern gt Gray scale of 9 steps tL Ramp Gray scale of 15 steps The eight equalizing bars correspond to eight tone levels of the test pattern except the darkest in the left end If you want to adjust the 2nd tone from left end on the test pattern use the equalizing adjustment
94. thumbnail on Control panel ViewSonic PJ358 55 www azulmarina com ventas azulmarina com www azulmarina com Displaying an image in full screen continued 2 Button operation for motion picture While motion picture is shown in full screen the following operation can be made from the control panel on the projector or the remote control Button Operation Pause and play motion picture Play Pause UR Play motion picture slowly half speed Play Play slowly half speed Fast forward motion picture RIGHT p Play gt Fast forward 2 times Fast forward 8 times Fast forward 4 times Fast rewind motion picture p gt Play gt Fast rewind 2 times Tr Fast rewind 8 times Fast rewind 4 times While UP button is being pushed the display mode is changed in every 2 seconds automatically Full screen Full screen motion picture motion picture 1 1 1 1 motion motion picture picture ZG SZ UP push for a while You can choose one in 4 display modes of Display in full screen with the progress bar Display in full screen without progress bar 1 1 display with the progress bar or 1 1 display without progress bar Note The motion picture is paused or restored whenever UP button is pushed ENTER Remote control l l UTE Display thumbnails on Control panel ViewSonic PJ358 56 www azulmarina com ventas azulmarina com www azulmarina com Maintemance Lamp A lam
95. u e When MODE is set to ONE TIME the last slide of the presentation will be hold on screen till either of ENTER button on the remote control or INPUT ENTER button on the projector is pushed ViewSonic PJ358 54 www azulmarina com ventas azulmarina com www azulmarina com Displaying an image in full screen One selected image file on Thumbnail menu can be displayed in full screen Use A E lt and gt buttons to move a cursor to select an image on Thumbnail menu Then push ENTER button on the remote control or INPUT ENTER button on the projector to display the selected image in full screen While in full screen mode if one of these buttons is pushed one more time the projector is back to Thumbnail display Full screen display 1 Button operation for still image While still image is shown in full screen the following operation can be made from the control panel on the projector or the remote control There are two type of KEY configurations for AIEI db button available USB STORAGE of the OPTION menu Button Key CONFIG 1 Key CONFIG 2 UP Turn around the image 90 degree clockwise Turn around the image 90 GE DOWN degree anticlockwise Display following image e bed Turn around the image 90 RIGHT Display following image degree clockwise Display previous image LEFT Display previous image e e Gide B ENTER Aenea NG Displays thumbnail Displays

Download Pdf Manuals

Related Search

Related Contents

簡 単 操 作  Horloge de départ HL 940 Mode d`emploi  Procedure for Calling C# PER Encode Methods  V11 sport 2003 1e2 serie 1 mgit  ThinkPad® T22 Service and Troubleshooting Guide    Guia de serviços  F。LDーNG TABLE F。LDーNG TABLEWーDE  User's Manual VARYTEC LED SIGN „OPEN“  Present&Information  

Copyright © All rights reserved. Failed to retrieve file