Operating Instructions (ETC-100)
Contents
1. T a __ fig 1 fig 2 fig 3 Status of indicators Fed lights Compressor works normally 2 Red flashes Compressor operation delayed Red lights Adjust parameters Operating instructions Examine parameter Press key amp show normal temperature after displaying upper limit emperature 2 Seconds press key w show normal temperature 2 seconds later after displaying bottom temperature press key set and no effect Password set In normal temperature state press key set at least 3 seconds to set password fig 1 the first figure flash pressa ar confirmation Atthe same time the screen display as the fig 2 then following the first step to input and canfirm the second and third password until it display FO1 in case the password 1s correct If in put an error password It will automatically return te the Fig for the input again If input error pass word for three times ar no operation in 30 seconds it will automatically return ta temperature displ aying state Enter into menu and display PO1 POS to change the password following the above step The orginal passwordis 111 If forget your password you can power off then press set amp ge synchronously and power on for 5 seconds until display on Now the password is the origial one change the password according to the above way Parameter setting Input the correct password and enter into the menu state Press to display the l2. Otamendi 530 CiS4056RH Buenos Aires Argentina ansal Te 5411 4958 2684 ansalttansal com ar REFN RACH SE Fax 5411 4958 2686 http WwwwW ansal com ar Operating Instructions ETC 100 Pre use Inspection and Requirements for installation he power voltage should conform to the mark on the controller and the voltage stability should be endured he controller is forbidden to be used in water or oyver maist environ ment and high tempeature powerful electromagnetic or high corrosive environment as well he sensor of the controllers is USA DALLS integrated temperature sensor and please strictly stick to the instructions to connect the wire so as to avoid the sensor being damaged he sensor s pilot wire power wire and output relay socket should be clearly separated fram ane another and the current should not be overloaded Specifications and Parameters Panel Size 3 345 Unitmm Fixing hole size 30x 71 Unitmm Environmental temperature 50 556 Relative Humidity 10 95 inoat allow to frost Basic technological parameters Power voltage 220VAC 10 S0es60HZ lt gt Power Less than 3 lt gt Resolution 0 1 when 21008 is 1 gt Range 50t0 120 amp Accuracy 10E 856 0 56 in other range less than D Relay contact capacity FARPA0VAC Man functions lt gt Temperature measurement and contral lt gt Temperature revised O Delayed protect Insert password for adjusting parameter 10 ut Lt
3. ast setting Press 4 or for amending press set for confirm and return to the original parameter Then press A or w for the next parameter and follow the above step ta finish the parameter setting When all the parameters have been adjusted press set at least 3 seconds ta w to input the first passweard 0 9 then press key g for confirm and exit the parameter setting state and back to the state of temperature measurement lf not press set atleast 3 seconds for confirmation or no operation in 30 seconds after adjusting allthe parameters t will also return to the temperature measurement state but the adjusted parameter is not saved and the instrument operate according to the original one Functions Fefrigerating function s refrigeration mode when the temperature of the refrigerator is higher than the upper temperature limit it will start to refrigerate and when the temperature of the refrigerator is lower than the bottom temperature limit it will stop refrigerating Celayed function When the first ime powered if the actual temperature higher than the upper temperature limit the system will notwork at once until the delayed time finished If the distance of operating the system delayed time the system may work at once if the distance lt the delayed time the system will nat work anly after the delayed time In heating mode no delayed time when operating the system Alarm functions lt gt Alarm for sensor s e
4. rror under the condition of being electrified when the refrigerator s sensor errors LED will flash while displaying E1 together with the buzzer humming lt gt Alarm for out of the measuring range when the temperature to be measured is higher than 120 or lower than 50 the controller will display E2 together with the buzzer humming lt gt Alarm muting under the condition of alarm status press any key to mute the alarming noise without change the LED displaying status Parameter information and setting ror smere aerate set bottom limit ae a Cras Tenperare gus e eo Password menu 50 119 The first Haute Wire connection plan Panel Picture Ends connection plan BBPBABABAABE Ei agree dha AC akelig wnead ansal Iw oon shh ies REF RIGERACA ON S ore wih 11 ered fee red ene nih 12 Otheraies the maran aE be dered TE K 20 LiF
Download Pdf Manuals
Related Search