INSTALLATION AND OPERATING INSTRUCTIONS
Contents
1. the device T280R Remote Probe Specifications Chemical Properties Non corrosive Water Resistant Max Compression Force Applied to Probe 10 Ib force Max Tensile Force Applied Between Probe and Cable 5 Ib force Max Cable Length 300 feet e The T280R may be extended from 15 up to 300 using shielded 24 AWG cable Insure the shield is grounded for noise immunity For the latest warranty information please go to http www security honeywell com hsc resources wa index html P O Box 9040 Melville NY 11747 Copyright 2008 H yw il N8188 2V3 11 08 Rev A Honeywell International Inc one e2. N8188 2V3 11 08 Rev A UlsTS300 DUAL TEMPERATURE SENSOR Honeywell INSTALLATION AND OPERATING INSTRUCTIONS INTRODUCTION The Honeywell Ademco TS300 is a hardwired temperature monitor able to accurately detect variations in temperature It can monitor the temperature at the unit and at a remote location using a T280R simultaneously Alarm annunciations include a local piezo sounder and two programmable NO NC outputs which activate when the mapped high or the low limit s is exceeded protecting equipment property and perishable items The NO NC alarm outputs may be delayed by increments of one minute to allow for expected momentary temperature variations such as during a refrigeration unit s defrost cycle The audible alert if programmed sounds when the temperature limit is violated and can be silenced with the press of a button for a programmed duration The TS300 can accurately monitor any temperature within the range from 32 F to 140 F OC to 60 C A T280R Remote Temperature Probe may be used to monitor temperature within the range from 40 F to 140 F 40 C to 60 C or to monitor temperature in a harsh environment INSTALLATION Mount the unit on a wall at a convenient viewing height For accurate temperature sensing at the unit do not mount the TS300 near any heat or cooling source If the unit does not trip the panel insure that the contact configuration NO NC as defined in the Setup Procedure agrees with that of the zone to wh
3. ich it is connected TO THE INSTALLER Regular maintenance by the installer and frequent testing by the user are vital to continuous satisfactory operation of any alarm system The TS300 and the T280R should be tested periodically at least once a month depending on conditions The installer should assume the responsibility of developing and offering a regular maintenance program to the user as well as acquainting the user with the proper operation and limitations of the alarm system and its component parts Recommendations must be included for a specific program of frequent testing to ensure the system s proper operation at all times Left Button Lowers Right Button Raises Numeric Values Numeric Values Fi Remote Remote Tamper Tamper Output 1 Common Output2 Common SPVVVVNNON Setup Mode Button Tamper Switch Illustration A SETUP PROCEDURE Remove the front cover from the TS300 With power applied to the unit press the SETUP MODE switch see Illustration A Press the Left button to lower a numeric limit by a value of one press and hold to decrement by tens Press the right button in raise a numeric limit by a value of one press and hold to increment by tens Pressing either button will toggle the either or choices When your preferred setting is displayed press the setup button to accept and move to the next parameter Note that when setting High Low limits in Centigrade mode incrementing decrementing wi
4. ight button for the remote probe The temperature you have requested will flash 5 times and then return to displaying the temperature of the sensor you have chosen to display Alarm If the temperature at an enabled sensor varies outside either of its mapped limits the audible annunciator will sound if programmed and the mapped output will switch to its alarm state but only after the selected delay time has expired If the delay time is set to 0 the alarm will be immediate The maximum delay time is 255 minutes 4 hours 15 minutes The output will remain in its alarm state until the temperature returns to within the selected limits as buffered by the programmed degrees of hysteresis As long as the temperature remains outside the selected temperature limits the display will cycle between the desired display temperature and the name of the limit s exceeded Silence The Audible alarm is silenced by pressing either of the buttons It will remain silenced until the silence timeout time expires and then it will become audible again In addition when the output delay time is in the final 60 seconds the audible will switch to a fast beep 250mS pulsed if it has been enabled High and Low Temp limits and Alarm Memory To display the programmed high and low temperature limits press and hold both buttons momentarily The unit will show the programmed limits followed by any alarms in alarm memory The TS300 stores the last 8 alarm events An alarm eve
5. ll raise lower the limit by the equivalent of 1 Fahrenheit or 10 F if button is pressed and held Table 1 Programmable Parameters Parameter Display Fahrenheit or Centigrade Remote Probe Enable REN YES Display Local or Remote BSP LEL temperature Set Local Sensor Low Limit LLO Set Local Sensor High Limit Set Remote Probe Low Limit Set Remote Probe High Limit Select Output Mode both relays NOTES if programmed for Normally Closed NC it is supervised if Normally Open NO it is unsupervised The Output map is a graphical representation of the possible choices The left character indicates which relay you are mapping 1 or 2 The middle character is the local sensor map and the right character is the remote probe map See Table 2 for map designations SHysteresis provides a buffer so that temperature that is shifting back and forth around the alarm limit point will not create multiple alarms You set the of degrees that the temperature will have to rise above the temperature low limit set point or drop below the high limit set point for the alarm to turn off For example if you set the HYS at 3 degrees and your low limit is 40 degrees you will go into an alarm condition when the temperature reaches 39 degrees and restore from alarm would not occur until the temperature rose to 43 degrees Hysteresis is limited to 1 2 the difference in degrees between the low temperature limit and high temperature limit or
6. nt is one where the relay output was activated If delays are used and the temperature restored before the delay time expired it is not considered an alarm and will not be stored in alarm memory Alarms are displayed as the limit that was violated For example LLO for local low limit The alarms are displayed most recent to oldest Alarm memory is cleared when you enter set up mode or when power is cycled to the unit TS300 SPECIFICATIONS TS300 SPECIFICATIONS Temperature Range Accuracy Local Sensor 32 F to 140 F 0 C to 60 C 3 F 1 7 C Temperature Range Accuracy Remote Probe 40 F to 140 F 40 C to 60 C 4 F 2 2 C Minimum Span between Hi and Low Limits 4F 2 2C Alarm Delay 0 255 minutes in 1 min increments Alarm Output Type 2 Form A reed relays Alarm Output Resistance 25 ohms maximum Alarm Output Rating 50 mA max 30 VDC Audible Alarm 4 kHz 75 dB 10 cm pulsed 750 mS on off Audible Alarm Silencing 0 255 minutes in 1 min increments Input Voltage 7 to 16 VDC Input Current 25 mA max Case Dimensions 4 x 2 6 x 0 9 10 2 cm x 6 6 cm x 2 3 cm T280R REMOTE TEMPERATURE PROBE purchased separately The T280R is a Remote Temperature Probe for use with the TS300 The Remote Probe is a sealed temperature sensor with 15 feet of two conductor 24 AWG stranded cable The cable should be connected to the two terminals labeled REMOTE Polarity need not be considered Caution Excessive force applied to the probe may damage
7. the programmed HYS setting max of 10 whichever is least The setup will NOT be lost in the event that power is lost at the panel Options that relate to the remote probe will only appear is you have enabled the remote probe in selection 2 of the table parameters High Low limits shown in table are degrees Fahrenheit Equivalent Centigrade temperatures apply when Centigrade has been selected Hysteresis is always programmed in degrees Fahrenheit even if Centigrade has been selected to set limits 2 Table 2 Output Map Designations utput 1 Local and Remote Low Output 1 not used rms Output 1 Local Low Alarm utput 1 Local Low and Remote ae Alarms Output 1 Local High Alarm utput 1 Local Low and Remote a and High Alarms Output 1 Local Low and High utput 1 Local High and Remote Alarms co Alarms Output 1 Remote Low Alarm utput 1 Local and Remote High aes Output 1 Remote High Alarm utput 1 Local High and Remote E and High Alarms Output 1 Remote Low and utput 1 All Alarms Local Low High Alarms a High and Remote Low and High Map designations Low Limit High Limit Both Low amp High Limits Examples The same choices can be used for relay 2 OPERATION Display The TS300 displays the selected temperature local ambient or remote in either Fahrenheit or Centigrade as programmed To check the temperature at a sensor press the left button for the local sensor or the r
Download Pdf Manuals
Related Search