Home

SMT-700 User Manual

1. If zoning is also enabled and the zone 2 sensor has been installed the LCD will alternate between the Outside Air Temperature and Zone 2 temperature every 5 seconds Outside Air Economy Function If Fitted To further improve on the efficiency of your air conditioning system saving energy and money in running costs your SMT 700 thermostat can use outside air for cooling if your air conditioning system has been designed and installed to take advantage of this advanced function If cooling is required and the outside air is sufficiently cool enough your SMT 700 will draw in the cooler outside air into the building rather than use the warmer internal air Again depending on the outside air temperature your SMT 700 may or may not run the air conditioning system compressor If outside air is being used to assist in cooling the word Economy will flash on the LCD Note this function cannot be used in conjunction with the Zone Control Function Page 13 of 20 Zone Control if fitted If zoning is enabled the word Zone and either 1 2 or 1 2 indicating both zones will be shown To select which zone s you wish to be controlled simply tap the On Off button to toggle between zone 1 Zone 2 or both zones If the optional Zone 2 Temperature sensor has been installed the second zone temperature will also be shown in the LCD Some homes or offices require temperature control in two separate areas a
2. the SMT 700 thermostat relies on having the correct day set for its programming functions to be accurate If using the programming functions the current day should be set correctly See programming on pages 5 amp 8 for details about setting the clock and day display Room Set Temperature This portion of the LCD displays the current room temperature Note this temperature may or may not be measured at the location of the SMT 700 wall controller In programming mode the current SET or desired room temperature is displayed in this location The temperature is display in either degree Celsius or degrees Fahrenheit as set by the installer Page 15 of 20 Outdoor Zone Temperature This part of the display requires optional sensors to be installed to enable this function Both the second control zone temperature and or outdoor temperature can be displayed Information on zoning can be found on page 14 information on the outdoor temperature display can be found on page 13 of this manual System Mode Indicator This part of the LCD provides information on the Air Conditioning System control mode The SMT 700 thermostat is capable of controlling heating only cooling only or both heating and cooling systems together If heating only mode is selected the word Heat is displayed If cooling only mode is selected the word Cool is displayed Auto season changeover mode is indicated by the words Heat amp Cool If the SMT 700 the
3. Page 12 details these functions Keyboard Lock Indicator When this symbol is shown parts of the keyboard are locked or the temperature control range is limited preventing changes to the thermostat settings When a button is locked or a control range is limited the Padlock symbol will flash to warn you that the current function is prohibited The SMT 700 thermostat has multiple levels of keyboard lock for both manual and programmable modes See page 14 of the manual for more information on this function Active Zone Indicator To aid in increasing comfort levels while reducing running costs the SMT 700 thermostat employs industry leading features One of these features is the ability to Zone or split your heating and or cooling system into 2 separate temperature controlled areas each can have their own temperature sensor Optional Zone 2 sensor required If zoning is enabled the Word ZONE and the numbers 1 and or 2 will be shown in the LCD If the optional zone 2 temperature sensor has been installed the second zone temperature will also be displayed and temperature control for that zone is also provided Further information on zoning can be found on page 14 of this manual Economy Mode Indictor If the outside air temperature is suitable the SMT 700 thermostat will use the cooler outside air rather than the warmer inside air to supplement the cooling capacity of your Air Conditioning system If the outside air is very co
4. Programmable Mode Your residential programmable thermostat is able to be programmed by you to automatically control the desired home heating and cooling temperatures amp 2 FN 4 times per day 7 days per week a separate heating and or cooling temperature can be programmed into the thermostat When the programmed time arrives your thermostat will FAWR EJ lt a automatically use the programmed desired heating and cooling temperature for that time to automatically control your home air conditioning system These programmed temperatures will remain active until the next pre programmed event arrives later that day or first event next day or until you override these temperatures manually The Buttons Explained On Off Zone Select if function installed Quickly press the On Off button to turn the SMT 700 thermostat On To turn the SMT 700 thermostat OFF press amp hold this button for 2 seconds until the word OFF is displayed in the LCD If the Zoning function is enabled see Zone Control on page 14 tap the On Off button to cycle between Zone 1 only Zone 2 only then both zones Page 4 of 20 Smart Temp SMT 700 User Manual Mode Tap this button to cycle the SMT 700 thermostat through the available modes Heat only Cool only Fan Only ventilation mode or Auto season change over mode See page 12 for more information on Modes Up A Use this button to increase the desired room temperature for the heating or coo
5. active zones as described on page 14 of this manual Manual Mode Quite often automatic time clock control of your air conditioning system is not required In these instances your installer will have set your SMT 700 thermostat to manual mode Manual mode provides the easiest form of climate control for your home or office Simply turn the SMT 700 thermostat on or off as required and set your desired temperatures These set temperatures will then remain active until you decide to set a new value Page 10 of 20 Smart Temp SMT 700 User Manual The Buttons Explained On Off or Zone Select if function is installed Quickly press the On Off button to turn the SMT 700 thermostat On To turn the SMT 700 thermostat OFF press amp hold this button for 2 seconds until the word OFF is displayed in the LCD Tap the On Off button to cycle between Zone 1 only Zone 2 only then both zones if zoning is enabled Mode Tap this button to cycle the SMT 700 thermostat through the available modes Heat only Cool only Fan Only ventilation mode or Auto season change over mode See page 12 of this manual for more information on Modes Up A Use this button to increase the desired room temperature for the heating or cooling modes or increase a value in programming modes Also used to force override the pre programmed temperatures and temporarily replace them with a new higher set temperature Down V Use this button to dec
6. briefly to confirm the copy process and your current days values will be copied to the days selected Normal programming will resume at the next day to be programmed Tip On days when the office will be unoccupied it is a wise idea to set the START and STOP programs to occur at the same time of day say 8 00am for example This way if FAN ON mode has been selected the fan will not start on those days where the office is un occupied After Hours Run Timer Note if zoning has been used in your office the after hours run timer function is automatically disabled An extremely useful feature of your SMT 700 thermostat is it s integrated after hours run timer function This timer is useful when you find yourself working outside of the normal office hours Tapping the On Off button will initiate the after hours run timer function where the SMT 700 thermostat will then temporarily substitute that days Stop program temperatures with that days Start program temperatures but only for a timed two hour period While this after hours run timer is operating the word Timer will flash on the LCD This function makes it extremely simple to return the office temperature to a comfortable working level without the fear of forgetting to turn the air conditioning system off at the end of your day Page 9 of 20 Tip To take advantage of the after hour timer function on days when the office is normally not open program
7. is choosing the most energy efficient fan speed for the current conditions Try selecting a speed manually with the fan button Fan On mode keeps the fan running 24 hours a day when in program mode or the fan stops shortly after heating stops This is not a fault Your SMT 700 advanced fan management program has been customised by your installer to operate this way Wall controller has no display Heating Cooling or Air Conditioning System seems to runs all night Check air conditioning main fuse Reset home A C fuse Call Smart Temp service Faulty Wiring fuse or SMT 700 Heating and or cooling temperatures set for typical day time or unachievable temperatures Fan set to Fan ON mode Call Smart Temp service Set a lower heat temperature and or a higher cooling temperature Review manual on setting temperatures Change fan mode to Auto See page 12 Heating or cooling system seems to start before the scheduled start time Optimised Start function may be on This is an installer set function See optimised start on page 14 above Call Smart Temp service for information on turning this function off if required Some buttons do not appear to operate Key board lock is on See page 14 for more information on this function This is not a fault Buttons or functions may be locked to prevent unauthorised tampering Page 18 of 20 Smart Temp SMT 700 User Manual Specificatio
8. program the thermostat use zone control if installed and get the most from your air conditioning system e Commercial Programmable Mode When using the SMT 700 thermostat in a commercial building special functions are available Capabilities such as after hours run timers outside air economy control and other commercial air conditioning management capabilities are detailed in this part of the user manual e Manual Mode can be used in either residential or commercial buildings Often programming or fully automatic air conditioning control is not required In these circumstances the installer will have set the SMT 700 thermostat for manual mode This mode is the easiest mode to use the air conditioning system in but it will not automatically turn you re A C system off or down at the end of the day e Common Functions This part of the user manual explains all the functions and capability that will be available to you regardless of what mode the thermostat has been put into by the installer e Advanced functions Your air conditioning system has some very advanced control and energy management capabilities This part of the manual will explain these capabilities so you are able to better understand why your air conditioning system and SMT 700 thermostat is behaving the way it is e Glossary This section of this manual will provide you with additional details on the function of buttons operational modes and LCD indicators etc Residential
9. set a more economical temperature than your start program to prevent your office over heating or becoming to cool at during the night You are permitted to have the Start and Stop event occur at a different time of the day and set a different heating and cooling desired set temperature for each of the 2 events You are able to set a heating set point temperature between Heating OFF and 38 degrees Celsius You are able to set a cooling temperature between zero degrees Celsius and Cooling OFF Programming your SMT 700 thermostat or setting these daily events is no more complicated than setting the clock as described previously The same buttons are used in the same sequence using the Clock button to advance to the next step and the up A or down Y buttons to make changes The LCD shows only relevant information for the event being adjusted thus reducing possible errors that may be caused by having confusing information displayed on the LCD This makes the programming of the SMT 700 thermostat a simple and logical process To enter the program mode press and hold the Clock button for 5 seconds The display will change and the Day Monday will flash Using the up A or down W buttons adjust the day to the day you wish to start programming or to the day you wish to edit an existing program Tap the clock button to advance to the next step The LCD will show the word Start with the hour s digit flashing Using the up A or down V but
10. starting momentarily to permit your air conditioning to pre warm To conserve energy your fan may continue to run monetarily after the heating or cooling has stopped to extract all the warm or cool air still remaining in the air condition system and bring that conditioned air into the building Fan On Mode By selecting Fan On or continuous fan mode the SMT 700 thermostat indoor fan will operate continuously between the Start or Wake programs and the Stop or Sleep programs and then turn on and off as required with heating and cooling outside of those programmed events if your SMT 700 is set as a Programmable thermostat Page 12 of 20 Smart Temp SMT 700 User Manual Please Note Your installer may have activated some of the many advanced indoor fan management capabilities of the SMT 700 thermostat that work in partnership with the Fan On Mode This may result in the fan operating differently than described above If you find this to be the case and un desirable please contact your authorised Smart Temp service agent for advice on altering the function Fan Speeds Single Fan Speed If your air conditioning system has one fan speed your SMT 700 thermostat will display the fan information shown on the picture to the left The words High Med or Low will be absent from the LCD Pressing the fan button with permit you to select either Fan On mode or Auto Fan mode as described abo
11. the thermostat set or you may find yourself at home when normally you would be away from your home possibly a sick day for example Simply press and hold the up A or down V buttons for 3 seconds The SMT 700 thermostat display will change to show the word SET and the active set point for the current mode Heating Cooling or Auto modes as you hold the up A or down W buttons the current set point will change If Auto mode is selected after adjusting the Heat set point wait without touching a button for 3 seconds for the SMT 700 thermostat display to change to show Cool and SET and your current set cooling temperature If desired change this value with the up A or down V buttons Again wait for 3 seconds to exit the temporary overridden programmed mode The LCD will now show Override and your new temporary setting will be in use until the next programmed event change occurs Should you need to cancel a temporary override simply press and hold both the up A AND V buttons for a few seconds The word Override will disappear from the LCD and your pre programmed settings will be restored Default Program Wake Leave Return Sleep Monday 7 00am Cis 25 930 Cooing 30 0 Coeling 25 Pm Costing 30 Tuesday 70am FEE TIE 0am eh H0 soopm Heete T0 oon ren 112 Wednesday 7 00am Cis 25 8308
12. Caoling 30 00 Coeling 25 Pm Costing 30 Tus Tom plethu HET vang est HOT sona Hee 120 apm Henne LE Friday 7 00am ESTEE E 8 30am COHEN 5 00pm EN 10 00pm COMEET Sd tam FESR LIET sam Heatin HET gown Hearne 120 mmm piene jD Heating 18 Heating 18 Heating 20 Heating 12 Sunday 8 00am Cooling 25 8 30am Cooling 30 5 00pm Cooling 25 10 00pm Cooling 30 Commercial Programmable Mode Your commercial programmable thermostat is able to be programmed by you to automatically control the desired office heating and cooling temperatures 2 times per day 7 days per week a separate heating and or cooling temperature can be programmed by you into the thermostat When the programmed time arrives your thermostat Auto Fan MODE Cooling will automatically use the programmed desired heating and cooling temperature to automatically control your office air conditioning system These programmed temperatures will remain active until the next pre programmed time arrives or until you override these temperatures manually or until you activate the 2 hour after hour run timer The Buttons Explained On Off After hours Override or Zone Select if function is installed Ouickly press the On Off button to turn the SMT 700 thermostat On where it will run your temperature control program To turn the SMT 700 thermostat OFF press amp hold this button for 2 seconds until the wo
13. EE RE cede ELE Y AE EE FE S EE eer dea HE HL 14 Optimised Starts P m 14 MGIOSS ANY Me 15 EDU DD soss 18 Warranty Information M 19 ICD 19 Contact ri e M 19 Page 3 of 20 Introduction Your air conditioning system has been fitted with an advanced and energy efficient thermostat controller The Smart Temp thermostat model SMT 700 is able to manage your comfort levels in a number of ways Your installer will have programmed your SMT 700 thermostat to specifically fit your needs the requirements of the building and the air conditioning equipment connected to it If after reviewing this manual there are features or functions that you would consider desirable and that are not active on your thermostat please contact your installer or another authorised Smart Temp service agent for advice on adding these functions To assist with the clarity of the manual it has been divided into the following 5 main sections e Residential Programmable Mode This section of the manual explains how to use the SMT 700 when installed in a home or apartment It contains information on how to
14. ER OFF will appear in the LCD When active the SMT 700 thermostat will automatically turn off after an installed owner set pre programmed duration of time This function is ideal for use in training or interview rooms for example where the room is not often used and where you want to ensure the air conditioning system is not left running for extended periods when the room is unoccupied Page 11 of 20 To provide warning of the pending shutting down of the A C system one hour before the A C system is about to turn off the words TIMER will flash in the LCD to provide you with ample warning Once the time period has expired the SMT 700 thermostat automatically turns the air conditioning system off If required pressing the On Off button will reset the countdown timer and the heating or cooling will restart for the installer set period of time Should you wish you can turn the SMT 700 thermostat off at any time by pressing and holding the On Off button for 2 seconds Common Functions Selecting Heating Cooling and Auto Modes Your SMT 700 thermostat is able to control the mode of your air conditioning system in a number of ways Using the Mode button you are able to select your desired air condition mode With each tap of the mode button the SMT 700 thermostat will cycle through Heating only mode Cooling Only mode Auto mode and Fan only ventilation modes These modes are described in more detail below Please Note To suit your
15. SMT 700 thermostat has either a single adjustable set temperature or a separate Day heating amp cooling set temperature and Night heating amp cooling set temperature If active switching between Day amp Night Modes is easily achieved by taping the clock button The Day heating and cooling set points are active when the SUN symbol is shown on the LCD The Night heating and cooling set points are active when the Stars amp Moon symbol is shown on the LCD To adjust the heating and cooling set points first select the day or night mode if active by tapping the clock button Press and hold the up A or down V buttons for a few seconds the LCD will change and show the word SET and the current mode heating cooling or auto set temperature press the up A or down WV to adjust this value to the desired set temperature If Auto mode is selected once the heating set point is as desired wait a few seconds without touching a button and the thermostat display will change to show the word SET and your COOLING set point will be displayed Again using the up A or down V button adjust your cooling set point to your desired value After a few seconds the thermostat display will return to normal and your new set temperatures will take effect Timer Mode In some applications the SMT 700 thermostat Auto OFF timer feature may have been activated by the installer When this function has been activated the word s TIMER or TIM
16. Tagging the days you desire press the Clock button to initiate the copy process The word Copy will flash briefly to confirm the copy process and your current days values will be copied to the days selected Normal programming will resume at the next day to be programmed Programming the Zones If Enabled As briefly touched upon in the above description your SMT 700 thermostat has the useful feature of being able to automatically change the Active Zones at pre set times if enabled by the installer For example this feature permits the SMT 700 thermostat to automatically switch the bedroom zone ON when the Sleep event starts or to automatically switch the unoccupied upstairs zone OFF during the day This has the benefit of reducing energy costs while still maintaining a comfortable living environment in the occupied areas of your home Naturally these settings can be overridden at any time by tapping the on off button to manually select active zones as described on page 14 of this manual Page 6 of 20 Smart Temp SMT 700 User Manual Temporary Temperature Override To make your SMT 700 thermostat even more capable and flexible it has been provided with a temporary program override function This permits you to temporarily change your event temperatures just for today and only until the next programmed event starts For example you may have guests visiting that would like it a little warmer or cooler than you would normally have
17. air conditioning system type either the Heating or Cooling function may have been disabled Heat Only Mode The SMT 700 thermostat will turn on the Heating when the room temperature falls below the Heat set point temperature by 0 5 deg Celsius In Heat only mode the SMT 700 thermostat will NOT bring on the Cooling regardless of the room temperature and the Cooling Set point temperature In Heat only mode only the word Heat will be displayed in the LCD When your air conditioning system is heating the word Heat in the LCD will change to the word Heating If the word Heat is flashing in the LCD the SMT 700 is performing a safety anti cycle delay prior to restating the heating Cool Only Mode The SMT 700 thermostat will turn on the Cooling when the room temperature rises above the Cool set point temperature by 0 5 deg Celsius In Cool only mode the SMT 700 thermostat will NOT bring on the Heating regardless of the room temperature and Heating set point temperature In Cool only mode only the word Cool will be displayed in the LCD When your air conditioning system is cooling the word Cool in the LCD will change to the word Cooling If the word Cool is flashing in the LCD the SMT 700 is performing a safety anti cycle delay prior to restating the Cooling Auto change Over Mode The SMT 700 thermostat will turn on the Heating if the room temperature falls below the Heat Set point temperature and the Coolin
18. caeeaeeeaeceeeceeeeeeneeees 11 Day 7 Night Set pornts af ACUVE oed nette RE e EXER DEREORR HR E HORE G lax eate RES p ett God SDO anii eund 11 Ter Mode een sn Ni cM ni teeter ere prt ern ater steerer tr eft A rer ee ere rere A 11 Common Fimction ss ciccscsssssscssecsssvavecssvesuesdsensvovsevesuessavevecuesuoesesead svnsvoswasasessvesesovayscosueovon sdesevesneceusuavsnssvesuesdsesevenssbasveouassoveossucs 12 Selecting Heating Cooling and Auto Modes sess eene ener ener tnet eren trennen trennen enne e nennen 12 ban Control E6915 nane n Y EDI mM UD MAC MU E 12 AUO Fan Modern a Y Du as Cn MM MEL C 12 Pan On Mode aceite imee meet eee EP Oi I i e Pe me oe i eodem edere 12 Fan Speeds EMUL eles 13 Simple Fan Speed ca ccs eise reo tienes athens ERE E E HE e enr e e RE DH e EP Ee selene 13 Three Fan Speed iae imer re i E I E EE He n n Pe HE EE Er e E e aint 13 Advanced Functions MEE Y 13 Outdoor Air Temperature Display cnt rene e etre rie n e e e Pe th e ee edad 13 Outside Air Economy Function If Fitted eee ee eeeeeeeeeee eene nee nne th ettet e e Eek eE ESEA SEE RENEE ERE 13 Changing Active Zones ie niente retenir e nr ere n o d n d eO E UR Ra eigen 14 Key Board Lock Function Lock uiii teret eir asses ease HC bad e ede e ee Fe re tede edad 14 Fan Speed Management iY WG HF rer EHE FRU
19. e difference between room and set temperature Optimised Start Optimised Start mode permits the SMT 700 thermostat to automatically calculate the most optimum time to start your air conditioning system so that your programmed set point temperature is reached AT the program start time Your A C system will therefore turn on before the scheduled event so that the set temperature is achieved at the scheduled event time not after it Page 14 of 20 Smart Temp SMT 700 User Manual Glossary The LCD Explained Room Temperature Clock Day Indicator Temporary Override Active Keyboard Locked Program Held A C fault detected Auto Off timer running Program Indicator 4 Elegance fault detected Manual Mode Zone Selected Outside Air being used A C mode Fan Mode Fan Speed Fan running animation Zone 2 amp outside air temp display Program Event Indicator If Wake Leave Return or Sleep are shown your SMT 700 thermostat is set as a programmable thermostat This mode of operation is perfect for those that live a structured lifestyle This is fully automatic mode where the residence occupier can pre program the home temperatures for 24 hours per day 7 days per week This is explained on page 4 of this manual 2 Program Event Indicator Start Stop or 2 event programming is typically used in commercial buildings where the Air conditioning is simply designed to turn on at a time typically in the
20. eg C lower than the cooling set temperature If you set the heating or cooling set point closer than this minimum value the SMT 700 thermostat will automatically push the other set point away to maintain this minimum value Tap the Clock button again and the day previously selected will be shown along with the word Stop The Hour digit will flash indicating that this value can now be adjusted with the up A or down V buttons Set the hour to the time you wish the STOP event to commence Continue to tap the Clock button to advance you through the Stop Minute then Stop Zone if enabled Stop Heating if enabled and Stop cooling if enabled temperatures Taping the Clock button again the LCD will show the word COPY You now have TWO options Option 1 Continue Programming as above Simply continue to tap the Clock Button as you have been to advance to the next day Tuesday in this example Start amp Stop then Wednesday Thursday etc following the same simple steps previously explained OR Option 2 Copy Program To copy the values you have just set to other days of the week Rather than taping the Clock button now tap the up A or down W buttons to TAG each additional day you wish to copy the currently set days program to When you have finished Tagging the days you desire then press the Clock button to initiate the copy process The word Copy will flash
21. ermostat is switched on will cycle the SMT 700 thermostat between Zone only operation Zone 2 only operating then both Zones operating When the zone is calling for warmed or cooled air it is directed to that particular zone in order to maintain that zone s desired temperature If the optional zone 2 temperature sensor has been installed then the temperature is also measured in zone 2 and controlled to the set point as well as the zone 2 temperature being displayed on the LCD Please note The SMT 700 thermostat will maintain a minimum of one open zone at all times To protect the air conditioning system and ducting you cannot turn both zones off at the same time Key Board Lock Function Lock Many of the features or functions of the SMT 700 can be locked by the owner or installer to prevent un authorised tampering When any locked function is attempted to be accessed your SMT 700 will flash the padlock symbol to inform you that the function is locked or a control limit has been reached Fan Speed Management As briefly touched upon previously in this manual fan speed management is a critical component of effective air conditioning control The fan is directly responsible for the air movement through your air conditioning system and home office and has a significant impact on how efficiently your air conditioning system operates If Auto Fan speed has been selected your SMT 700 will automatically select the most appropriate fan speed based on th
22. g if the room temperature rises above the Cool Set point temperature by 0 5 deg Celsius This is the recommended mode as it provides automatic control of the air conditioning system to maintain the desired room temperature Auto changeover mode is indicated by both the words Heat amp Cool in the LCD If the word Heat or Cool is flashing in the LCD the SMT 700 is performing a safety anti cycle delay prior to restating the air conditioning system Fan Only If Fan only is selected the SMT 700 thermostat will turn on the system fan for continuous operation The SMT 700 thermostat will not control the heating or cooling system regardless of the room temperature and the heating and cooling set point temperature s If Fan only is chosen the words Heat or Cool are NOT shown in the LCD In Fan only mode the fan will operate 100 of the time Fan only mode is typically used for ventilation purposes Fan Control Logic Fan management of an air conditioning system is vitally important to achieve maximum comfort and energy efficient operation The fan of your air conditioning system is able to operate in two main modes each mode is described below Auto Fan Mode If the user has selected Auto Fan mode with the FAN button the indoor fan will turn on when the heating or cooling turns on and off again once the heating or cooling turns off To prevent cool drafts occurring when the heating first starts the fan may delay
23. item s at our discretion Faults not warrantable will be charged a service fee Exclusions This warranty does not include incidental or consequential damage that may result from using this equipment Nor does this warranty cover abuse rain or moisture damage or using this equipment outside of the quoted specifications Page 19 of 20
24. ling modes or increase a value in programming modes Also used to force override the pre programmed temperatures and temporarily replace them with a new higher temperature Down V Use this button to decrease the desired room temperature for heating or cooling modes or decrease a value in programming modes Also used to force override the pre programmed temperatures and temporarily replace them with a new lower temperature Clock Tap the clock button to begin setting the clock Press and hold the clock button for 2 seconds to begin programming your daily events Fan Single Speed Fan Tap this button to cycle between Continuous fan Fan ON and Auto Fan Three Speed Fan Tap this button to cycle between Low Medium High amp Auto Fan speeds Press and hold this button for 5 seconds to toggle between Continuous fan Fan ON and Auto Fan Setting The Clock Your SMT 700 thermostat is fitted with a real time clock This clock is used by the SMT 700 thermostat for the programming functions described below It is essential that the clock time and day are set accurately if you require your programmed events to start on time To set the clock tap the clock button The LCD will show the Hours Digit flashing Use the up A or down V button to adjust the hours to the correct time note the AM PM symbol Tap the clock button again and now the minute s digits will flash Adjust this value using the up A or down V button to sh
25. living and sleeping zone or upstairs and downstairs for example If your SMT 700 thermostat shows the word ZONE then the Zoning function is active on your SMT 700 thermostat You may also have information on the temperature in the second zone if the optional second zone temperature sensor has been installed If you have the Zoning function active on your SMT 700 thermostat and the zone 2 temperature sensor is installed then your desired temperature will be exactly maintained in both zones of your home or office The SMT 700 thermostat will automatically open and close dampers motorised valves that regulate the flow of air in the ducting that carry the warmed or cooled air from the Air Conditioning system to the various areas of the home or office as well as controlling the Air Conditioning system to ensure the correct air temperature is directed to the appropriate area of the home or office This capability not only vastly improves the comfort in the home or office especially in two story buildings or difficult to temperature regulate arrears it dramatically reduces the energy costs by only operating Air Conditioning system in the arrears or zones that require it This function eliminates the over heating or over cooling effects of some air conditioning controllers Note this function cannot be used in conjunction with the Outside Air Economy Function Changing Active Zones Simply tapping the On Off button while the SMT 700 th
26. lt detected Communication loss between main PCB and wall controller should be strongly suspected Re boot Elegance by turning the MAIN PCB off not the wall controller if fault persists Call Smart Temp service Word FAULT shown on LCD A C fault detected Call A C system service Temperature display seems inaccurate Air from the wall cavity may be leaking into the rear of the thermostat sensor enclosure External heat or cool source such as lamps televisions or drafts from open doors affecting the accuracy of sensor Plug holes in wall with tape to prevent leaks Move lamps vents or other sources of abnormal temperature away from sensors Sensor calibration may setting are incorrect Call Smart Temp service for information on calibrating the air temperature sensor Cannot enter heat or cool modes SMT 700 thermostat set for Heating or Cooling only modes Heating or cooling mode may not be available on your air conditioning system Fan sometimes stops and starts intermittently while heating is running This may not be a fault You air conditioning system may be running a de ice maintenance function The indoor fan is turned off during these events to prevent drafts being felt inside the building If this occurs to often an air conditioning fault may have occurred Contact Smart Temp for information on this event Fan speed changes frequently This may not be a fault Your SMT 700
27. mn MP HaiLiri HERETIC Chgance SMT 700 User manual lesk Congratulations on the purchase of your new Thermostat Your new air conditioning system thermostat has been built using the best components and design philosophy currently available As a result if properly installed your Smart Temp SMT 700 thermostat will provide you with many years of trouble free comfort The wall thermostat has been designed by Smart Temp Australia P L to be an attractive highly reliable and an easy to use thermostat By taking the time to read and understand these simple instructions you can take advantage of many of the capabilities that are offered in this high quality product Important READ THIS FIRST The SMT 700 thermostat has been designed to be a very flexible amp powerful Air Conditioning controller It has many industry leading and innovative functions and capabilities This manual provides information on all capabilities offered by this thermostat even those function that have not been required on your installation Therefore please use the index provided and read the sections of this manual only relevant to your installation and disregard functions or features that not applicable Page 2 of 20 Smart Temp SMT 700 User Manual Index Contents DMEF ODUCOION eMe Kosos 4 Residential Programmable Dr 4 The Buttons Explained eee e
28. morning maintain a single temperature all day then switch off at the end of the day or maintain a more economical overnight temperature The words highlighted on the LCD indicate this mode is set and whether the Building A C system is running This function is described on page 7 of this manual Manual Mode Indicator The Sun or Moon symbol or the lack of any programming information such as Start amp Stop or Wake Leave Return amp Sleep indicate the SMT 700 thermostat is in Manual Mode This mode is perfect for those who have a less structured lifestyle Your SMT 700 thermostat may be set to provide two separate set points offering a Day temperature and a separate Night temperature to be set and easily swapped between the two as needed Alternatively a single heating and cooling set point may be provided In this case the day amp night symbols will not be shown This function is described in more detail on page 10 of this manual Clock The clock displays the time This time is used by the SMT 700 thermostat in program modes 2 or 4 events to set the start stop or program events It is important that the clock is set correctly if the SMT 700 thermostat is used in a Programmable mode The Clock is NOT used by the SMT 700 thermostat in manual mode it simply displays the time See programming on pages 5 amp 8for details about setting the clock Day Indicator As with the clock described above
29. ns Taput Voltage steep niens 24V AC 240V AC fused selectable Operating Temperature 0 50C 32 to 122F Operating RH 0 95 non condensing Size seus 113 x 103 x 23mm Display Sizes esee et ERR RE 74 x 55mm Temp Sensors se enisi andes 10K NTC type 3 Accuracy 0 3deg C 21 C Display resolution sss 0 1 deg C Control Range een a ERRE Off to 38c Outside Air temp display range es 8 60c Back light cnau eese et ei et Blue EL Optimised Start method Time to Start Vs Temp Differential method Communications Protocol Native RS485 150M max run with 4 core screened cable Warm Start sire Hee Fan Coil gt 33c Fan coil lt 27c Fan coil lt 21c installer adjustable Pan speedsas ze Y AY Based on difference between room and set temp Economy function sse Outside air cooler gt 2 5c dampers only gt 5c suspend comp call Approval reme CE C tick Warranty Information This product is warranted to be free from manufacturing defects for 24months from the date of sale Should a warranty claim be required contact Smart Temp Australia or place of purchase for a return authorisation number prior to returning any suspected faulty components Warranty 1s strictly return to base cost of freight back to Smart Temp will be the responsibility of the sender Smart Temp or approved agent will repair or replace the faulty
30. ol then the SMT 700 thermostat may decide to stop the A C system completely and only use this cooler outside air to cool the building This reduces running costs while improving the indoor air quality The SMT 700 thermostat will inform you that it is using outside air by showing the word Economy on the LCD See page 13 for more detail on this function Auto Stop timer Manual Mode only After Hours Run Timer Commercial Mode Only The word Timer will be displayed whenever a SMT 700 thermostat timer function is active The SMT 700 thermostat has a number of inbuilt timer functions that use this part of the display depending on which mode or installer function has been set Whenever the words TIMER or TIMER OFF is displayed the SMT 700 thermostat is performing a timing function relevant to your mode of operation These functions are described in multiple places throughout this manual in sections relevant to the specific operational mode of this function Page 16 of 20 Smart Temp SMT 700 User Manual Current Program Overridden The SMT 700 thermostat LCD will display this word when the SMT 700 thermostat pre set program has been temporarily overridden See page 7 amp 10 for more details of this function A C Fault Indicator The SMT 700 thermostat is capable of monitoring the safety of your air conditioning system or an external device critical to the safe and correct operation of your air conditioner If a fault is detec
31. our SMT 700 thermostat is fitted with a real time clock This clock is used by the SMT 700 thermostat for the programming functions described below It is essential that the clock time and day are set accurately if you require your programmed events to start on time To set the clock tap the clock button The LCD will show the Hours Digit flashing Use the up A or down V button to adjust the hours to the correct time note the AM PM symbol Tap the clock button again and now the minute s digits will flash Adjust this value using the up A or down V button to show the correct minute Tap the Clock button again and now the week day flashes again use up A or down V button to set this value to the correct day of the week Tap the clock button again to exit the clock set function Programming Your 2 Daily Events The SMT 700 thermostat is an individual 7 day programmable thermostat For each day of the week you are able to have 2 time schedules or programmed events occur For clarity these events are conveniently named Start and Stop The Start event is used to set the time you wish your office to start at the beginning of the day You can program your desired heating and cooling temperatures that you wish your office to be when the start event begins The Stop event is used to set the temperatures you wish office to be at the end of the working day You are able to program your heating and or cooling to OFF or simply
32. ow the correct minute Tap the Clock button again and now the week day flashes again use the up A or down V button to set this value to the correct day of the week Tap the clock button again to exit the clock set function Your clock is now set Programming Your 4 Daily Events The SMT 700 is an individual 7 day programmable thermostat For each day of the week you are able to have 4 time schedules or programmed events For clarity these events are conveniently named Wake Leave Return amp Sleep The Wake event may be used to set the temperatures of your home that you would like to wake up to The Leave event is typically used to set the temperatures you wish your home to maintain whilst you are away at work The Return event is often used to set the temperature you wish to be greeted with upon returning home at the end of the day The Sleep event can be used to set a comfortable and energy efficient temperature while you sleep You are permitted to have every event occur at a different time of the day and set a different heating and cooling set temperature for each of the 4 events You are able to set a heating set point temperature between Heating OFF and 38 degrees Celsius You are able to set a cooling temperature between zero degrees Celsius and Cooling OFF provided the installer has not set control limits Remember each of the 4 event programmed set temperatures will hold the home tempera
33. rd OFF is displayed in the LCD If zoning is enabled Tap the On Off button to cycle between Zone 1 only Zone 2 only then both zones If zoning is disabled Tap this button to toggle the 2 hours after hours run timer on or off Page 7 of 20 Mode Tap this button to cycle the SMT 700 thermostat through the available modes Heat only Cool only Fan Only ventilation mode or Auto season change over mode See page 12 of this manual for more information on Modes Up A Use this button to increase the desired room temperature for the heating or cooling modes or increase a value in programming modes Also used to force override the pre programmed temperatures and temporarily replace them with a new higher set temperature Down V Use this button to decrease the desired room temperature for heating or cooling modes or decrease a value in programming modes Also used to force override the pre programmed temperatures and temporarily replace them with a new lower set temperature Clock Tap the clock button to begin setting the clock Press and hold the clock button for 2 seconds to begin programming your daily events Fan Single Speed Fan Tap this button to cycle between Continuous Fan Fan ON and Auto Fan Three Speed Fan Tap this button to cycle between Low Medium High amp Auto Fan speeds Press and hold this button for 5 seconds to toggle between Continuous Fan Fan ON and Auto Fan Setting The Clock Y
34. rease the desired room temperature for heating or cooling modes or decrease a value in programming modes Also used to force override the pre programmed temperatures and temporarily replace them with a new lower set temperature Clock Tap the clock button to select day or night mode 1f enabled Press and hold the clock button for 2 seconds to set your SMT 700 clock Fan Single Speed Fan Tap this button to cycle between Continuous fan Fan ON and Auto Fan Three Speed Fan Tap this button to cycle between Low Medium High amp Auto Fan speeds Press and hold this button for 5 seconds to toggle between Continuous fan Fan ON and Auto Fan Setting The Clock Manual Mode Your SMT 700 thermostat is fitted with a real time clock This clock is simply provided to display the current day and time It has NO functional control for the thermostat at all To set the clock Press amp Hold the clock button for 5 seconds The LCD will show the Hours Digit flashing Use the up A or down V button to adjust the hours to the correct time note the AM PM symbol Tap the clock button and now the minutes digits will flash Adjust this value using the up A or down V button to show the correct minute Tap the Clock button again and now the weekday flashes again use up A or down V button to set this value to the correct day of the week Tap the clock button again to exit the clock set function Day Night Set points if Active The
35. rmostat requests the air conditioning to supply warmed air the word Heating will be displayed If the SMT 700 thermostat requests the air conditioning to supply cooled air the word Cooling will be displayed If the Word Heat or Cool is slowly blinking the SMT 700 thermostat is waiting for an installer set safety delay time to expire before activating the function This delay period is to protect the A C system under the SMT 700 thermostat control Fan Running Animation A small animation of a fan revolving will be displayed whenever the air conditioning system fan is running Note all separate parts of the fan animation are shown in the picture on page 15 When the SMT 700 thermostat is running normally only the necessary parts of the LCD necessary to provide the fan running animation will be displayed Fan Speed Indicator The SMT 700 thermostat can control up to three speeds of indoor fan if the installer has enabled this function The manually selected fan speed is shown Auto fan speed is shown by the three words Low Med amp High in the LCD at one time The automatically selected fan speed will flash Fan Mode Indicator The SMT 700 thermostat can turn the indoor fan On amp Off in a number of ways depending on whether the SMT 700 thermostat is used in commercial or residential buildings or whether the SMT 700 thermostat is heating or cooling This is displayed as AUTO FAN or FAN ON mode
36. s selected after adjusting the Heat set point wait without touching a button for 3 seconds for the SMT 700 thermostat display to change to show Cool and SET and your current set cooling temperature If desired change this value with the up A or down W buttons Again wait for 3 seconds to exit the temporary overridden programmed mode The LCD will now show Override and your new temporary setting will be in use until the next programmed event change occurs Should you need to cancel a temporary override simply press and hold the up A AND Y buttons for a few seconds The word Override will disappear from the LCD and your pre programmed settings will be restored Programming the Zones if enabled Note if zoning has been used in your office the afterhours run timer function is disabled As briefly touched upon in the above description your SMT 700 thermostat has the useful feature of being able to automatically change the Active Zones at pre set times if enabled by the installer For example this feature permits the SMT 700 thermostat to automatically switch to the second zone ON when the Start event starts or to automatically switch the unoccupied boardroom zone OFF during the day This has the benefit of reducing energy costs while still maintaining a comfortable environment in the occupied areas of your office Naturally these settings can be overridden at any time by tapping the on off button to manually select
37. t point closer than this minimum value the SMT 700 thermostat will automatically push the other set point away to maintain this minimum value Tap the Clock button again and the Day previously selected will be shown along with the word Leave The Hour digit will flash indicating that this value can now be adjusted with the up A or down V buttons Set the hour to the time you wish the Leave event to commence Continue to tap the Clock button to advance you through the Leave Minute then Leave Zone if enabled Leave Heating if enabled and Leave cooling if enabled temperatures Again by continuing to tap the Clock button you will advance to through the Return program and then Sleep programs for the day you have chosen to program Taping the Clock button again the LCD will now show the word COPY You now have TWO options Option 1 Continue programming as above Simply continue to tap the Clock Button as you have been to advance to the next day Tuesday in this example Wake Leave Return Sleep then Wednesday Thursday etc following the same simple steps previously explained OR Option 2 Copy Program To copy the values you have just set to other days of the week Rather than taping the Clock button now tap the up A or down V buttons to TAG each additional day you wish to copy the currently set days program to When you have finished
38. ted all heating and cooling calls are suspended to further protect the air conditioning system and the indoor fan may be locked to LOW speed Installer set function The SMT 700 thermostat can be turned OFF if required by pressing and holding the On Off button for 2 seconds If this symbol frequently turns on and off regularly or is displayed permanently then you will need to contact your air conditioning installer to check your system and reset any faults that have been detected SMT 700 Thermostat Fault Indicator As well as monitoring the status of the air conditioning system the SMT 700 thermostat also monitors its own health The Spanner symbol will show on the LCD to inform you that an internal fault has been detected When a fault is detected all heating and cooling calls are suspended to protect the system from harm and to prevent run away heating or cooling conditions occurring The indoor fan is locked to LOW speed to maintain a minimum level of ventilation during this fault condition Depending on the fault you may or may not be able to turn your SMT 700 thermostat OFF with the On Off Button If this symbol is displayed on and off regularly or is displayed permanently you will need to contact your Air Conditioning installer to check your system and reset any faults that may have developed Page 17 of 20 Troubleshooting Symptom Suspected Fault Suggested remedy Spanner symbol on in LCD Internal SMT 700 thermostat Fau
39. the Start program at 8 00am for example with your normal office occupied heating and cooling set temperatures and set the Stop program for the exact same time 8 00 am in this example and the set temperatures to your normal Stop program values Off for example The SMT 700 will move straight to the Stop program and not run the air conditioning system but will have a valid Start temperature in memory ready for use by the afterhours run timer function For an office that is NOT open on a weekend an example of a Saturday and Sunday program is given below Day Time Suggested Heat set point Suggested Cool set point Saturday Start 8 00 am Heat set 22c Cool Set 25c Saturday Stop 8 00 am Heat Set OFF Cool Set OFF Sunday Start 8 00 am Heat set 22c Cool Set 25c Sunday Stop 8 00 am Heat Set OFF Cool Set OFF Temporary Temperature Override To make your SMT 700 thermostat even more capable and flexible it has been provided with a temporary program override function This permits you to temporarily change your programmed event temperatures just for today and only until the next programmed event starts Simply press and hold the up A or down V buttons for 3 seconds The SMT 700 thermostat display will change to show the word SET and the active set point for the current mode heating cooling or auto modes as you hold the up A or down V buttons the current set point will change If Auto mode i
40. tons to adjust the hours to the time you wish the Start event to commence for the day selected Page 8 of 20 Smart Temp SMT 700 User Manual Tap the Clock button again now the minute s digits flashes Using the up A or down W buttons set the minute to the time you wish the Start event to commence Tap the Clock button again If the SMT 700 thermostat has been set by the installer to control the optional climate zoning AND if the option to program the zones has been set by the installer you will now have the ability to set which zones you require to be ON during the Start event Using the up A or down W buttons set the zones you wish to be ON for the Start event If the installer has set to the Program Zone option OFF this step is skipped by the SMT 700 thermostat during the programming sequence Tap the Clock button again now the word Heat if heating mode is enabled by the installer and a temperature value is shown in the LCD using the up A or down V buttons set the desired Heating temperature for the Start event Tap the Clock button again now the word Cool if cooling mode is enabled by the installer and a temperature value is shown in the LCD using the up A or down Y buttons set the desired Cooling temperature for the Start event NOTE there must be a minimum of 1 deg C difference between heating and cooling set points The heating temperature must be at least 1 d
41. tt peret t testes ete arra eo Eee EHE EX HER LE LEY re ERE Pret EYE ee Iustin edge e dee ree edid 4 susnpacrehucm 5 Programming Your 4 Daily Events ccccesccsccesseeseesceeseeeseeeseeeecesecesecesecsaecaaecsaecaaecsaecaeeeaeseaecaeesaeseseseaeseeeseeseeeeaecesesneeeeeeneeees 5 Programming the Zones If Enabled sss eene en DELYN DYDDYN EDD e nennt 6 Temporary Temperature Override ccccccccseesseescesscesecesccesecsecuaecsaecaeecaeecseeeaeeaeecseeeaeseneseeeeesesecesecaeceaecaeceseseseseeeeereeneeeeees 7 Ier qoriBgquucrnir Snn P nnnnno 7 Kia IICBAUELC IMERRR 7 sunnalcehdc 8 Programming Your 2 Daily Events cccccsccssecsseesecseecssesseeeseeeeesccesecsecaecaaecsaecsaecsaecaeesaeseaecaeecaeeeseseneseeeseeseseaeceeeeeeeaeeeneeess 8 After Hours Run TIMET oee un YU YDY FO FFRED Cyd NU ND GY GC YH 9 Temporary Temperature Over de ss ui a a GU YN IU absit O GY OG Lat 10 Programming the Zones if enabled sse eene nennen eene Ene EE aai R aniani aa 10 Manual MOde eerte eher een tepore ER EE Oe SER ER ERE SERES YER EE VR r EBORE RY YN 10 he Buttons Explained aen aeu ED eSI MENSIS EUM 11 Setting The Clock Manual Mode cecccesesssesseeseeeesceseceseceeceacesecaeceaeceaeceaeceaecaeecaeseaeseaesnessesseeeeaeesae
42. ture until the next scheduled event time arrives where it s set temperature will be used So The Wake set temperature will be the temperature of your home until the Leave time arrives then The Leave set temperature will be the temperature of your home until the Return time arrives then The Return set temperature will be the temperature of your home until the Sleep time arrives then The Sleep set temperature will be the temperature of your home until the next days Start time arrives Programming your SMT 700 thermostat or setting these daily events is no more complicated than setting the clock as described previously The same buttons are used in the same sequence using the Clock button to advance to the next step and the up A or down V buttons to make changes The LCD shows only relevant information for the event being adjusted thus reducing possible errors that may be caused by having confusing information displayed on the LCD Page 5 of 20 To enter the program mode press and hold the Clock button for 5 seconds The display will change to show the Day Monday flashing Using the up A or down V buttons adjust the day to the day you wish to start programming an event or to the day you wish to edit an existing event Tap the clock button to advance to the next step The LCD will show the word Wake with the hour s digit flashes Using the up A or down V buttons adjust the ho
43. urs to the time you wish the Wake event to commence for the currently selected day Tap the Clock button again now the minute s digits flashes Using the up A or down W buttons set the minute to the time you wish the Wake event to commence Tap the Clock button again If the SMT 700 thermostat has been set by the installer to control the optional climate zoning AND if the option to program the zones has been set by the installer you will now have the ability to set which zones you require to be ON during the wake event Using the up A or down W buttons set the zones you wish to be ON for the Wake event If the installer has set to the Program Zone option to OFF this step is skipped by the SMT 700 thermostat during the programming sequence Tap the Clock button again now the word Heat if heating mode is enabled by the installer and a temperature value is shown in the LCD using the up A or down W buttons set the desired Heating temperature for the Wake event Tap the Clock button again now the word Cool if cooling mode is enabled by the installer and a temperature value is shown in the LCD using the up A or down V buttons set the desired Cooling temperature for the Wake event NOTE there must be a minimum of 1 deg C difference between heating and cooling set points The heating temperature must be at least 1 deg C lower than the cooling set temperature If you set the heating or cooling se
44. ve If your air conditioning system is fitted with 3 fan speeds your SMT 700 thermostat will display the fan speeds as shown on the picture to the left Pressing the fan button will step the fan speed selection through Low then Med ium then High and finally Auto fan speed indicated by all three fan speeds being shown on the LCD If auto fan speed has been selected the SMT 700 thermostat will indicate the automatically selected fan speed by flashing in appropriate word in the LCD Press and hold the Fan button for 3 seconds to toggle between Auto fan where the fan turns on and off with heating and cooling and Fan On where the fan will run continuously most of the time as set by the system installer If Auto Fan Speed has been selected as indicated by all 3 fans speeds being shown on the LCD your SMT 700 thermostat will automatically select the fan speed based on the difference between the room and set temperature Please Note If zoning is enabled To protect the Air Conditioning ducting and other components the installer may have selected the high fan speed to be locked out if only one zone is on Advanced Functions Outdoor Air Temperature Display The SMT 700 thermostat can be fitted with an optional outdoor air temperature sensor to display the current outdoor air temperature on the LCD The outdoor air temperature is displayed in the lower left of the LCD along with the words Outside Air Temperature

SMT-700 User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents