Home

USER MANUAL - PRO-SOLUTIONS\Inicio

1. 1 Installation Install the device at a vibration free oscilation free and fire resistant location Connect the connection cable of the power unit with the DC IN socket Plug the power unit into your outlet 5 2 Sound control The sound control works via the built in microphone or via the sound input socket Connect the sound signal from the mixer e g Master 2 with the Jack socket on the rear panel input sensitivity 0 1 V 1 V Please note The controller comes without pre programmed programs These must first be programmed by the user You can select one of the 4 chaser in order to test the sound control 5 3 Connection with the dimmerpacks DMX 512 The wires must not come into contact with each other otherwise the fixtures will not work at all or will not work properly Only use a stereo shielded cable and 3 pin XLR plugs and connectors in order to connect the controller with the fixture or one fixture with another Building a serial DMX chain Connect the DMX output of the tem with the DMX input of the nearest dimmerpack Always connect one output with the input of the next fixture until all fixtures are connected Caution At the last fixture the DMX cable has to be terminated with a terminator Solder a 120 resistor between Signal and Signal into a 3 pin XLR plug and plug it in the DMX output of the last fixture 6 OPERATION Install the device on a plane surface Operation via the included power u
2. a soft lint free and moistened cloth Never use alcohol or solvents There are no serviceable parts inside the device Maintenance and service operations are only to be carried out by authorized dealers 9 TECHNICAL SPECIFICATIONS Power supply 220 V AC 50 Hz via 9 15V DC 300 mA power unit included in the delivery Power consumption 1 W Number of control channels 4 8 4 integrated chasers 8 Free programs 4 84 scenes Sound control via built in microphone or audio input Dimensions LxWxH 255 147 70mm Weight 1 5 kg Please note every information is subject to change without prior notice
3. controller ON 2 Select the desired program s by pressing the respective Program button s 3 Adjust Masterfader for total output 4 Adjust Speed Fader until the spots react in the desired speed You can invert the program selection by pressing the Prog lt gt button This function is designed for bands etc 6 5 Memorize a program With theitem you can memorize 4 different programs with up to 84 steps each Press and hold the Prog lt gt button and select the desired program number via the Program button The Prog lt gt LED is lit and the Program LED flashes Press the Prog lt gt button again and the Prog lt gt LED is off Push the Master fader to maximum Push channel faders to the desired setting Press the Program button in order to memorize the first step The LEDs flash 3 times Repeat the steps mentioned above until you have memorized all steps Press and hold the Prog lt gt button and the current Program button in order to memorize the chaser lf the program is full you must first delete the program 6 6 Adjust Fade Time Push the Fade Time Fader to the desired level 6 7 Call up several chasers continuously The programs and chasers can be called up individually or combined Press all Chaser buttons and Program buttons so that their LEDs are lit Adjust Masterfader for total output Adjust Speed Fader until the spots react in the desired speed The running order is CH1 2 3 4 PR 1 2 3 4 Empty pro
4. etc This product is allowed to be operated with a direct voltage of DC 9 15 V 100 mA and was designed for indoor use only Do not shake the device Avoid brute force when installing or operating the device When choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust There should not be any cables lying around You endanger your own and the safety of others This device must never be operated or stockpiled in sourroundings where splash water rain moisture or fog may harm the device Moisture or very high humidity can reduce the insulation and lead to mortal electrical shocks When using smoke machines make sure that the device is never exposed to the direct smoke jet and is installed ina distance of 0 5 meters between smoke machine and device Do not permit operation by persons not qualified for operating the device Please use the original packaging if the device is to be transported 4 FEATURES Features Comfortable DMX controller DMX lighting controller 4 8 12 channels 4 8 12 channel faders with LED Fade Time fader with LED for adjusting the step time Master fader with LED for adjusting the total output level Speed fader for adjusting the program speed Flash button per channel and master flash LED display of all modes 4 freely programmable programs with up to 84 steps each Controller comes with 4 pre programmed chasers The programs and chasers can be calle
5. USER MANUAL SCENE 4 SCENE 8 CAUTION Keep this device away from rain and moisture Unplug mains lead before opening the housing For your own safety please read this user manual carefully before you initially start up Every person involved with the installation operation and maintenance of this device has to be qualilfied follow the instructions of this manual 1 INTRODUCTION Thank you for having chosen the controller You will see you acquired a powerful and versatile device Unpack your item Before you initial start up please make sure that there is no damage caused by transportation Should there be any consult your dealer and do not use the device 2 SAFETY INSTRUCTIONS This device has left our premises in absolutely perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual This device falls under protection class lll The device always has to be operated with an appropriate transformer Always disconnect from the mains when the device is not in use or before cleaning it Keep away children and amateurs from the device There are no serviceable parts inside the device Maintenance and service operations are only to be carried out by authorized dealers 3 OPERATING DETERMINATIONS This device is a DMX controller for controlling DMX effects or spots in discotheques on stages
6. d up individually or combined CH1 2 3 4 PR 1 2 3 4 Dimmer Manual control of the channels via sliders Full On all channels can be switched on together Blackout function Program speed adjustable via speed fader or Tap Sync button Sound control via external signal or integrated microphone Sound to light via jack Power supply via included power unit or 9 V battery included in the delivery Interface descriptions 1 2 3 4 5 6 7 8 9 CHANNEL LEDs CHANNEL FADERS These faders will adjust the output of the channels from 0 to 100 or O to 255 FLASH BUTTONS Press to activate maximum channel output MASTERFADER For adjusting the general output MASTER FLASH BUTTON Press to activate maximum channel output SPEED FADER To adjust chaser or program speed TAP SYNC BUTTON In AUTO CHASE press it twice to define chasing speed FADE TIME FADER Move to adjust fade time CHASER BUTTONS 10 PROGRAM BUTTONS 11 AUDIO BUTTON Press it to get into audio control 12 PROGRAM lt gt BUTTON This button will reverse the program chaser direction 13 FULL ON BUTTON When activated whole channel output will be maximum and disable BLACK OUT 14 BLACKOUT BUTTON This button will force all DMX to 0 Rear panel descriptions 15 Battery compartment 16 Audio input socket 17 DMX output socket 18 DMX POLARITY selector 19 Power switch 20 Power supply socket 5 SETUP 5
7. grams will be ommitted 6 8 Invert the chaser direction Press the Prog lt gt button The Prog lt gt LED is lit The chaser direction is inverted 6 9 Sound control lf the chaser is to be run sound controlled press the Audio button LED is lit If the chaser is to be run exactly in the bass beat pull Speed fader to minimum and enter the bass beats by pressing the Tap Sync button repeatedly 6 10 Delete a program Press and hold the Prog lt gt button and select the desired program number via the Program button The Prog lt gt LED is lit and the Program LED flashes Press and hold the Tap Sync button and the current Program button in order to delete the program The LEDs flash 5 times Press and hold the Prog lt gt button and the current Program button in order to leave this mode 6 11 Set all channels to maximum Press the Full On button and all channels will be set to their maximum value As soon as you release the button the channels return to their original setting 6 12 Blackout Mode Press the Blackout button and all devices will be set to Blackout mode 7 PROBLEM CHART PROBLEM CAUSE REMEDY power unit and any extension cables Blackout button the Prog lt gt LED is off and the current Program button in order to delete the program 8 CLEANING AND MAINTENANCE Disconnect from mains before starting maintenance operation DANGER TO LIFE We recommend a frequent cleaning of the device Please use
8. lled through chasers Inthis mode all 4 chasers of the item can be run sound controlled You can manually adjust the individual channels via the channel faders the Masterfader and via the flash buttons 1 Turn controller ON 2 Select the desired chaser s by pressing the respective Chaser button s 3 Adjust Masterfader for total output 4 Press the Audio button so that the spots react to the sound signal You can invert the chaser selection by pressing the Prog lt gt button This function is designed for entertainers and party rooms 6 3 Prog Sound Mode Spots run sound controlled through internal proarams Inthis mode all 4 freely programmable programs of the item can be run sound controlled You can manually adjust the individual channels via the channel faders the Masterfader and via the flash buttons 1 Turn controller ON 2 Select the desired program s by pressing the respective Program button s 3 Adjust Masterfader for total output 4 Press the Audio button so that the spots react to the sound signal You can invert the program selection by pressing the Prog lt gt button This function is designed for discotheques 6 4 Prog Speed Mode Spots run speed controlled through internal programs inthis mode all 4 freelv proarammable proarams of the item can be run speed controlled You can manually adjust the individual channels via the channel faders the Masterfader and via the flash buttons 1 Turn
9. nit Connect the connection cable of the power unit with the DC IN socket Plug the power unit into your outlet Inserting Replacing the battery Please refer to the explanations under Operating Determinations Open the battery cover on the bottom and remove it lf replacing the battery remove the old battery from the battery compartment Caution Danger of explosion when battery is replaced improperly Only replace by the same type or similar types recommended by the manufacturer Remove empty battery in accordance with the instructions of the manufacturer Insert the battery and make sure that the poles are correct Replace the battery cover and close it In order to have a long battery life you should only use alcaline batteries With the POWER switch you can switch the device on and off BATTERY DISPOSAL NOTICE Please dispose of old and used batteries properly Batteries are hazardous waste and should not be disposed of with regular domestic waste Please take old and used batteries to a collection center near you 6 1 Hold Dimmer Mode Call spots manually In the Hold Dimmer Mode the connected spots can be called manually and be controlled via the channel faders Adjust the desired function via the channel faders 1 Turn controller ON 2 Adjust channe faders 3 Adjust master fader for total output This function is useful for theatres and booth illumination 6 2 Chaser Sound Mode Spots run sound contro

USER MANUAL - PRO-SOLUTIONS\Inicio

Contents

Download Pdf Manuals

Related Search

Related Contents