SRX-T615 Installation Manual
Contents
1. des Screw Cable clamp SRX T615 1 19 E 1 7 Adjustment of Projector Tilt The tilt adjustment of this unit is performed when adjusting the image position and so on 1 Loosen the nut 2 Adjust the projector tilt by rotating the adjuster Rotate clockwise direction O To raise the height of this unit Rotate counterclockwise direction O To lower the height of this unit 3 Fix the adjuster by tightening the nut toward the adjuster pipe Example of tilted projector Adjuster pipe Adjuster 1 20 E SRX T615 2 1 section 2 Adjustment SRX Controller This unit can be operated the adjustments and setting using the supplied SRX Controller For about installation of SRX Controller refer to the Operating Instructions 2 1 1 PC Specifications of Personal Computer PC Intel Pentium M 1 6 GHz or more and OS recommended CPU RAM capacity 256 MB or more 512 MB or more recommended and OS recommended Communication LAN 10OBASE T 100BASE T or COM RS 232C Graphics mode XGA 1024 X 768 or higher HDD Built in Drive having an empty capacity of 15 MB or more e OS 2 1 2 Microsoft Windows Vista Business SP2 English or Japanese version except for X64 Edition or Windows 7 Enterprise SP1 English or Japanese version Microsoft Windows XP support has ended Do not connect PC on2. None IG INSTALLATION SERVICE SETTING amp ru BOESEN Sets the various settings of this unit Refer to Section 2 2 2 1 5 Function Memory You can register the settings that have been adjusted in the control screens to FUNCTION 1 to FUNCTION 8 As the default setting the settings are registered to FUNCTION 1 To register the settings to FUNC TION 2 to FUNCTION 8 select one of the FUNCTION 2 to FUNCTION 8 from the pull down menu then adjust the items in each screen To gain access to the registered setting value select the desired FUNCTION from the pull down menu LNote The system may temporarily enter a muting state for a maximum of about ten seconds when the pull down menu of FUNCTION is switched during switching to another FUNCTION setting After that the muting state is switched to the selected setting screen Screen example FUNCTION SRX T615 127 0 0 1 2 1 6 Log Function If you select File Save Log on the menu bar of the control screen the communication log between SRX Controller and this unit from the startup of SRX Controller to that point of time can be stored up to 5 MB SRX T615 2 13 E 2 2 Setting of This Unit The status of this unit is set 2 2 1 Operation Method of Setting 1 Start the SRX Controller then click the SETTING tab Refer to Section 2 1 3 The SETTING screen is displayed SETTING tab Screen exam
3. AIR FILTER TIMER FAN CONTROL amp INFORMATION MAINTENANCE TIMER COLOR SPACE CONVERTER VERSION INFORMATION GG ZONE button MAIN version 3 19 0600 or later 2 10 E SRX T615 Q WHITE BALANCE Performs the Gain R G B adjustment for setting the color temperature It is used to adjust the subtle difference of color among the projectors when more than one projector is used When adjusting only one projector use Color Space Converter The default value is 50 During ordinary adjustment use at a value of 50 or less For a value of more than 50 a signal may be deformed Adjustment when more than one projector is used 1 Perform the CSC adjustment for all projectors Refer to Section 2 6 2 Project the 80 white signal 3 Determine a projector to be used as reference Adjust the gain value of other projectors so that the color becomes the same as that of the reference projector 2 REGISTRATION ADJUST Moves R red G green and B blue in the horizontal and vertical directions up to two pixels one pixel at a time so as to adjust registration e On Selects when adjusting e Off Selects when not adjusting e H Pixels move in the horizontal direction R Red pixels horizontally move up to two pixels one pixel at a time when you click the button G Green pixels horizontally move up to two pixels one pixel at a time when you click the button B Blue pixels horizontally m
4. 1 2 E SRX T615 1 1 3 External Dimensions Front view 634 694 389 i Left side view Refer to the optional lens list 340 622 104 L Air Intake Air Intake Bll 91 B 460 Input output Heat t terminal exhaust 637 309 x LKRL LIST No LKRL E REMARKS 1 Z511 258 297 2 Z514 230 283 3 Z519 244 4 A502 462 Including in 3D lens filter 5 A503 462 Including in 3D lens filter SRX T615 Top view Right side view 109 35 Bottom view 213 Rear view 622 340 Air Intake Air Intake gt Air Intake Air Intake Heat exhaust A ee Air Intake Air Intake lt Heat exhaust e 10 M8 for fixing the projector AC power cable F5 D K ea T gl ef A IE BH d S S Ge kr a a 18 299 ts 549 8 199 L 938 gl 169 Unit mm SRX T615 1 1 4 Installation of Carrying Handle Wh
5. 2 36 E SRX T615 2 6 1 Correcting the Color Space sRGB 709 1 Start the SRX Controller then click the SERVICE tab Refer to Section 2 1 3 The SERVICE screen is displayed SERVICE tab example SES 8 EE COLOR SPACE CONVERTER Select sRGB 709 in Color Space of the COLOR SPACE CONVERTER Click the button Click the button The color space function becomes OFF and then the characteristics of this unit can be measured Select Gray 10 in Test Pattern Select Measure the value of x and y at the center of screen using the color meter Enter the measured value of x and y in the W box of Projector Color Gamut in COLOR SPACE CONVERTER Project Red 1 Green 1 and Blue 1 in Test Pattern Select and measure the x and y values in the center of the screen Enter the measured values in step 8 in the R G and B fields of Projector Color Gamut Click the CALC button Click the APPLY button Project Gray 10 Red 1 Green 1 and Blue 1 again and measure the x and y values in the cen ter of the screen Confirm that the error between the measured values in step 12 and the value of Target Color Gamut is within 0 005 Gamma may be misaligned when specifications are not satisfied Readjust the gamma in this case When adjusting color space DCDM or AdobeRGB purchase an optional trimming
6. 2 39 E 2 7 1 Edge Blending Seng 2 39 E 2 7 2 Correction of Distortion after Edge Blending Adjustment annen eenen 2 41 E 2 7 3 Color Matching of Edge Blending 2 43 E 1 E Manual Structure Purpose of this manual This manual is the installation manual of 4K Digital Projector SRX T615 This manual is intended for use by trained system and service engineers and de scribes the information for installation of this unit Related manuals The following manuals are prepared for this unit Safety Regulations supplied with this unit This manual describes the information required to safely use this unit Operating Instructions available on request This manual is necessary for application and operation of this unit Maintenance Manual available on request This manual describes the information about the maintenance of this unit periodic check cleaning etc e Service Manual available on request This manual describes the information that premise the service based on part re placement of this unit Trademarks 2 E Trademarks and registered trademarks used in this manual are follows The terms HDMI and HDMI High Definition Multimedia Interface and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries e Windows and Windows Vista are the registered trademarks of Microsoft Corpora tion in the United States a
7. Clicking the button resets air filter timer FAN CONTROL amp INFORMATION Displays the information on the rotation frequency of a fan used in this unit and sets the cooling method The cooling method is set as described below During use of a 450 W lamp e Installation at an altitude of 0 to 500 m Set to Model Installation at an altitude of 501 to 1000 m Set to Mode2 e Installation at an altitude of 1001 to 1500 m Set to Mode3 When installing at an altitude of 1501 m or more contact your local Sony Sales Office Service Center During use of a 330 W lamp e Installation at an altitude of 0 to 500 m Set to Model e Installation at an altitude of 501 to 1000 m Set to Mode2 e Installation at an altitude of 1001 to 2000 m Set to Mode3 When installing at an altitude of 2001 m or more contact your local Sony Sales Office Service Center MAINTENANCE TIMER Elapsed Timer Displays the lighting time of a lamp Operation Timer Displays the operating time including cooling COLOR SPACE CONVERTER Adjusts the CSC Refer to Section 2 6 VERSION INFORMATION Displays the version of this unit ZONE button When the MAIN version is earlier than 3 19 0600 this button is not displayed Corrects the misregistration by adjusting R Red G Green and B Blue of the image Refer to Section 2 5 1 2 12 E SRX T615 6 SETTING tab Screen example SETTING tab
8. SOZ Adjuster Handle arm SRX T615 1 7 E 4 Insert the pipe short into the handle arms then fix the pipe with the two M8 bolts 5 Attach the pipe short on the other side in the same way Pipe short Pipe short 1 8 E SRX T615 1 1 5 Connection External reproduction device External reproduction device Left side of this unit 5 0 0 D D emm em oes mm se Ss ett oO HDMI cable SRX T615 1 9 E 1 2 Installation of Duct Basically there is no problem even if Sections 1 2 to 1 5 are not performed in sequential order However do not connect the power cord in Section 1 6 before Sections 1 2 to 1 5 are completed Attach the 8 inch duct to the duct connecting portion on the rear side of the top portion of this unit e When attaching the duct be careful not to bend the duct for exhausting the air smoothly e For the required exhaust air volume refer to 1 1 2 Required Equipment Tools phat 8 inch duct Duct connecting portion SRX T615 1 10 E 1 3 Installation of Lens e When performing the installation removal of lens be sure to shut down this unit by the SRX Controller then turn off the power switch on the rear side of this unit e When performing the installation removal of lens
9. be careful not to touch the lens board 2D lens 3D lens Board Although the illustration used here for description is the 2D lens the installation procedure for the 3D lens is the same as the 2D lens 1 Raise the lens fixing lever toward the E side with the lock button pushed all the way in lock released If you raise the lens fixing lever without pushing the lock button the lock button and lens fixing lever will be damaged Be sure to push the lock button and check that the lock is released before raising the lever Lens fixing lever Lock button SRX T615 1 11 E 2 Attach the lens to this unit while firmly holding the lens not to drop it and aligning the position When attaching the lens to this unit insert it straight 3 Lower the lens fixing lever to fix the lens Lens Lens fixing lever A ING LXR Lens fixing wl 1 12 E SRX T615 1 4 Installation of 3D Lens Filter In the Case of LKRA 005 In the LKRA 005 Installation Manual the procedure for installing LKRA 005 in SRX R320S is de scribed When installing LKRA 005 in this unit follow the procedure in this manual e Be careful not to attach the filter bracket A B assemblies in the wrong position e Attach the knob securely to prevent the lens filter from dropping Attach the three filter bracket A assemblies with the six screws suppli
10. 2014 7 32 9 878 503 02 2013
11. CPU is required SRX T615 2 17 E 2 2 5 Profile The setting value of this unit is stored in PC or the setting value stored in PC is written in this unit Screen example SRX T615 127 0 0 1 PICTURE CONTROL COLOR CONFIG INSTALLATION SERVICE amp SETTING amp FLMCTOH FUNCTIONT vi Profile Save Load Save Place a check mark in the setting value to be stored in PC File Edit and select the file name to be stored button Select the file e SAVE button Store the checked setting value in the specified file Load Place a check mark in the setting value to be written in this unit from PC File Edit and select the file name to be written 5 a button Select the file to be written e LOAD button Write the checked setting value in this unit from the specified file After loading is executed be sure to restart this unit by turning the power switch on the rear side of this unit off and on again Tip In the case that PC and this unit are connected by Ethernet PC Communication Network and IPv6 cannot be set 2 2 6 Signal Input from Optional Board In the case of using an optional board if you change an input signal at the optional board it sometimes appears noise on a screen It is recommended to perform the masking for approximately 5 seconds in advance 2 18 E SRX T615 2 3 Lens Adjustment This adjustment is not required when using this unit by only a 3D lens 2 3 1 Position Ad
12. Horizontal Setting value Blending width 512 48 560 Screen example MASKING ADJUST EDGE BLENDING Horizontal SP oi Vertical SS Wi BLENDING button 5 Click the BLENDING button The EDGE BLENDING screen is displayed EDGE BLENDING Left on Marker Right oee Oo df Upper Width Lower CLOSE 6 Click the button in Right and select 512 in Width Click On of the radio button in Marker A green line is displayed at the start point of blending and a red line is displayed at the end point It is recommended to set Upper and Lower to 256 or 512 7 When the setting is completed click the button 2 40 E SRX T615 2 7 2 Correction of Distortion after Edge Blending Adjustment After performing the blending adjustment of the two projectors a misregistration as shown below may oecur due to the image distortion This image distortion is corrected 1 Start the SRX Controller then click the SERVICE tab Refer to Section 2 1 3 The SERVICE screen is displayed MASKING ADJUST EDGE BLENDING SERVICE tab Screen example R PEN o ED EN EEEN EECH 2 Click the BLENDING button of MASKING ADJUST EDGE BLENDING The BLENDING DISTORTION ADJUST screen is displayed BLENDING DISTORTION ADJUST Tip The marks o in BLENDING DISTORTION ADJUST indicate the adjustment points PEN EM nn ooo ct SRX
13. REGISTRATION ADJUST of the SERVICE screen If the misregistration still remains then perform the fine adjustment e The fine adjustment can be performed only when the projector MAIN version is 3 19 0600 or later The version can be confirmed in MAIN of VERSION INFORMATION Refer to the following screen 1 Start the SRX Controller then click the SERVICE tab Refer to Section 2 1 3 The SERVICE screen is displayed ZONE button SERVICE tab Confirm the MAIN version pos DES REGISTRATION ADJUST VERSION INFORMATION 2 Click the ZONE button The ZONE REGISTRATION ADJUST screen is displayed Screen example f Test Pattern Zone Adjust SRX T615 2 35 E 3 Click On of the radio button in Test Pattern The following image is displayed on the screen Cursor Center of image 4 Move the cursor to the center of the image by clicking the Lel gt IL buttons 5 Adjust R Red and B Blue images so that they are overlaid with G Green image using the El buttons while viewing the images When you click the El buttons the image moves in the direction based on the IMAGE FLIP Off setting Therefore if the image is displayed in the state of IMAGE FLIP On the image moves in the opposite direction Even if the IMAGE FLIP is On the cursor moves in the same direction as in the state of IMAGE FLIP Off Tip The correction moving amount of the center in the horizontal di
14. filter kit and perform the adjustment after replacement of a trimming filter A correct color does not appear even if you perform adjustment before replacement When replacing the trimming filter contact your local Sony Sales Office Service Center SRX T615 2 37 E 2 6 2 Correcting the Color Space Single 3D The CSC for the left eye lens and right eye lens is corrected 1 Start the SRX Controller 2 Select Single 3D HDMI 1 L R Single 3D HDMI 2 L R or Single 3D HDMI 1 L 2 R in INPUT SELECT The current state enters a 3D mode 3 Click the SERVICE tab INPUT SELECT SERVICE tab Screen example ES COLOR SPACE CONVERTER Click the button in Right of CUT OFF Perform steps 3 to 13 in Section 2 6 1 Select CSC for the right eye such as Single 3D Right1 in Color Space of COLOR SPACE CON VERTER 8 Click the ON button in Left of CUT OFF 9 Perform steps 3 to 13 in Section 2 6 1 10 Click the OFF button in Left of CUT OFF 11 Click the COLOR CONFIG tab and then set Color Space for the left eye and right eye COLOR CONFIG tab SS On 2 Screen example PP SRX 1615 127 0 0 1 Dr Pas Hel ur sync ress o ISTALLATION SERVICE A SETTING amp FUNCTION Color Space Color Space 2 38 E Select CSC for the left eye such as Single 3D Left1 in Color Space of COLOR SPACE CONVERTER SRX T615 2 7 Edge Blending Adjustm
15. the projector A as the reference projector 1 Perform the following with the SRX Controller of the projector B 1 Start the SRX Controller then click the SERVICE tab Refer to Section 2 1 3 The SERVICE screen is displayed Screen example MASKING ADJUST EDGE BLENDING SERVICE tab EEEN CEN 5 0 200 CEN SRX T615 2 43 E 2 Click the SHADING button of MASKING ADJUST EDGE BLENDING The SHADING SETTING screen is displayed Screen exampl Position Level Test Pattern Fo o 3 Set Position Only for the projector B Position is set depending on where the image overlaid portion encircled by dotted line is located in the image of the projector that is not the reference one In this case Left for the projector B Image of projector A Nat Image of projector B 4 Click On of the radio button in Test Pattern 2 Perform 1 2 and 4 in step 1 with the SRX Controller of the projector A In the projector A the Position setting 3 is not performed Select Levell in Level for both projector A and projector B Visually adjust R Red G Green and B Blue of the projector B using the El buttons Adjust Level2 to Level8 by repeating steps 3 and 4 After completing the adjustment click Off of the radio button in Test Pattern Click the button I DAR Y 2 44 E SRX T615 Printed in Japan SRX T615 SY J E Sony Corporation
16. 15 1 17 E 1 6 Connection of Power Cord Use the 3 core power cord that satisfies AWG 8 250 V rated and 40 A rated or more Connect the power cord to the AC IN terminal block on the rear side of this unit in the following proce dure e Connection of the main power and the electric wiring work should be done by qualified electricians only e Do not plug the power cord into the power supply before completing all of the following connecting operations 1 Remove the four screws then remove the terminal block cover Terminal block cover Screws 2 Remove the screw then remove the cable clamp 3 Remove the screw then remove the ground terminal Ground terminal Ka Cable clamp Ge 1 18 E SRX T615 4 Apply solder to the end of the ground wire 5 Attach the ground terminal removed in step 3 to the ground wire then fix it with the screw Cd Screw k N Apply solder Ground terminal Ground wire 6 Route the power cord through the hole on the bottom of the terminal block then fix each terminal with the screw as shown in the illustration 7 Fix the power cord using the cable clamp and screw 8 Attach the terminal block cover Ground terminal 4 Power cord
17. SONY 4K DIGITAL PROJECTOR SRX T615 Homi INSTALLATION MANUAL 1st Edition Revised 1 AS COVAa7 Wis V CABHCT BRERA TOV AY ICA Sdt HEAR MUR BHC ERTS ERE KK A BL tin TEMBOET SEREN Bied HEZE alt eh BD In CHAS SL A WARNING This manual is intended for qualified service personnel only To reduce the risk of electric shock fire or injury do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so Refer all servicing to qualified service personnel A WARNUNG Die Anleitung ist nur f r qualifiziertes Fachpersonal bestimmt Alle Wartungsarbeiten d rfen nur von qualifiziertem Fachpersonal ausgef hrt werden Um die Gefahr eines elektrischen Schlages Feuergefahr und Verletzungen zu vermeiden sind bei Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen Andere als die angegeben Wartungsarbeiten d rfen nur von Personen ausgef hrt werden die eine spezielle Bef higung dazu besitzen A AVERTISSEMENT Ce manual est destin uniquement aux personnes comp tentes en charge de l entretien Afin de r duire les risques de d charge lectrique d incendie ou de blessure n effectuer que les Us r parations indiqu es dans le mode d emploi a moins d tre qualifi pour en effectuer d autres Pour toute r paration faire appel une personne comp tente uniquement ZORD AWA HE DEK WAKE EF For kundene i Norge On DZ AAS AED FOR hc BEL IE
18. Section 2 3 adjustments using a Projector Refer to Section 2 3 Color Adjustment Tool with the Jh 2D lens installed Jh Perform registration adjustment J Perform image adjustment Refer to Section 2 5 Install the 3D lens then D Refer to Section 2 4 perform image adjustment Jh Refer to Section 2 4 Jh Perform gamma and uniformity 3 Perform registration adjustment adjustments using a Projector f Refer to Section 2 5 Color Adjustment Tool Perform registration adjustment e ES Refer to Section 2 5 Jh Perform color space J Perform gamma and uniformity correction CSC adjustment Perform color space adjustments using a Projector Refer to Section 2 6 correction CSC adjustment Color Adjustment Tool with the Jh Refer to Section 2 6 2D lens installed Perform edge blending it adjustment Perform color space Refer to Section 2 7 correction CSC adjustment Refer to Section 2 6 SRX T615 1 1 E 1 1 2 Required Equipment Tools The equipment and tools required for this unit are as follows Equipment tools Projection lens Description Prepare the necessary lens es in accordance with the installation environment LKRL Z511 LKRL Z514 LKRL Z519 LKRL A502 LKRL A503 Tip Regarding the selection of lens contact your local Sony Sales Office Service Center 3D lens filter LKRA 005 etc Lamp Prepare one of the following lamps in accordance with the installation env
19. T615 2 41 E The adjustment points corresponding to the image are as shown below 00 OO Q Q 3 Double click the adjustment point gt of first The adjustment screen is displayed Adjustment screen Screen example Jus Sore BLENDING Left Right 4 Perform the adjustment so that the two images are connected without distortion by using the El buttons 5 Adjust the images at the adjustment points and in the same way The entire image is moved 6 If the misregistration between the images still remains perform the fine adjustment at other adjust ment points 7 Repeat steps to 6 with the other projector 2 42 E SRX T615 2 7 3 Color Matching of Edge Blending After performing the color space conversion CSC adjustment of the two projectors if the color of the image overlaid portion is different from the color of other portion perform this adjustment Image of projector A Image of projector B e Perform this adjustment after completing 2 6 Color Space Conversion CSC Adjustment If the color matching of edge blending is performed before the CSC adjustment the entire adjustment may not be able to be performed due to the lack of correction amount e Use one projector as the reference projector and adjust the other projector to the reference projector Do not change the values of the reference projector In this section an example is described using
20. TEXO Dette utstyret kan kobles til et IT str mfordelingssystem NETWORK I 47 4 EROR blCOUY TEA BOF MICE o T TO For safety do not connect the connector for periph eral device wiring that might have excessive volt age to the following port NETWORK connector Follow the instructions for the above port SRX T615 Table of Contents Manual Structure Purpose of this manual Related manuals eso den varvanveeverseevnssndondende deed BEETLE 1 Installation Vl Outines areon ee AE SE enne 1 1 E 1 1 1 Installation FLOW asosini 1 1 E 1 1 2 Required Equipment Tools nn 1 2 E 1 1 3 External Dimensions nanne oneens eneen 1 3 E 1 1 4 Installation of Carrying Handle eee 1 5 E 1 1 5 Connection 1 9 E 1 2 Installation of Duct annen nennen eneen verven 1 10 E J Installation of EENS gege Eed 1 11 E 1 4 Installation of 3D Lens Filter In the Case of LERA 005 Jesis on svenn eden 1 13 E 1 5 Installation of Lamp seent eege 1 16 E 1 6 Connection of Power Cord 1 18 E 1 7 Adjustment of Projector Tilt 1 20 E 2 Adjustment 221 SRX Controller oane fend E r 2 1 E 2 1 1 Specifications of Personal Computer PC 2 1 E 2 1 2 COMME CHON E 2 1 E 2 1 3 2 1 4 2 1 5 Function Memory cecceccesceseeseeseeseeneenseeee 2 13 E 2 1 6 Log Runetten ege 2 13 E 2 2 Setting of This Unit aanne nenne eneen en vennen 2 14 E 2 2 1 Operation Metho
21. d of Setting 2 14 E 2 2 2 Owner Information 2 2 3 Network osise ro iassa dace 2 2 4 PC CommUnicatioi essiri sissors sra 2 2 5 Rebeet eege 2 2 6 Signal Input from Optional Board SRX T615 KE ue E 2 19 E 2 3 1 Position Adjustment nen 2 19 E 2 3 2 Position Adjustment Electric Shift Using SRX Controller aen 2 22 E 2 3 3 Position Adjustment Adjusting the Projector Tilt and Direction eese 2 23 E 2 3 4 Brightness Adjustment 2 4 Image Adjustment 3D Lens 2 25 E 2 4 1 Optical Axis Adj stment sisisi 2 25 E 2 4 2 3D Lens Filter Adjustment In the Case of LKRA 005 2 4 3 Zoom Focus Adjustment 2 4 4 Position Adjustment Adjust Image Using SRX Controller en 2 30 E 2 4 5 Position Adjustment Adjusting the Projector Tilt and Direction 2 30 E 2 4 6 Alignment of the Horizontal Position of Image for Right Eye and Image for Left Eye ess ccsestcsesstivess ccseesciseawssaceicssentseaueses 2 4 7 Image Mapping 2 4 8 Brightness Adjustment annen 2 34 E 2 5 Registration Adjustment aaneen nennen eneen 2 35 E 2 5 1 Fine Adjustment of Registration 2 35 E 2 6 Color Space Conversion CSC Adjustment 2 36 E 2 6 1 Correcting the Color Space sRGB 709 2 37 E 2 6 2 Correcting the Color Space Single 3D 2 38 E 2 7 Edge Blending Adjustment ne
22. djustment screws 3D lens filters Adjustment screws 3D lens filter tilt adjustment 1 Loosen the two adjustment screws 2 Tilt the 3D lens filter 3 Tighten the adjustment screws Adjustment screw this screw is also attached on the other side 3D lens filter 2 28 E SRX T615 2 4 3 Zoom Focus Adjustment The image for the right eye and the image for the left eye are adjusted separately The adjustment procedure is the same Project the test pattern Frame Adjust Refer to steps 1 to 4 in Section 2 4 1 Loosen the zoom lock screws and focus lock screws Adjust the image size by rotating the zoom rings Adjust the image focus by rotating the focus rings ier ZE St E Tighten the zoom lock serews and focus lock screws Zoom lock screw image for right eye Focus ring image for right eye Zoom ring image for right eye RS ao We z Z YS IKS L Re SZ Nowa foc S SR Zoom ring image for left eye Zoom lock screw image for left eye Focus ring image for left eye Focus lock screw image for left eye The 3D lens filters are not shown in the illustration for the sake of clarity SRX T615 2 29 E 2 4 4 Position Adjustment Adjust Image Using SRX Controller The position adjustment of 3D lens in the horizontal direction is performed using the SRX Controller Although it can be performed using the H shi
23. e moves in the upper direction with the button button Right Mid Area H Moves the image in the horizontal direction with the 1 4 portion of the right side image as the center The center and right end of the image do not move H The image moves in the right direction with the button H button Fix the center and right end 2 9 E Left Mid Area V Right Mid Area V Moves the image in the vertical direction with the 1 4 Moves the image in the vertical direction with the 1 4 portion of the left side image as the center portion of the right side image as the center The center and left end of the image do not move The center and right end of the image do not move V The image moves in the upper direction with the button V The image moves in the upper direction with the button V button ee ee es Corner Adjust Displays the adjustment screen when you double click the adjustment points A to H When you click the button these points move away from the center Screen example Comer Adjust Adjustment screen 5 SERVICE tab Screen example SERVICE tab DES WHITE BALANCE REGISTRATION ADJUST CO 3 LAMP CONTROL amp INFORMATION
24. e of contents and the type of a screen in SINGLE 3D ADJUST The image size can be adjusted using the and buttons of Size when you select the item beginning with Scope SRX T615 2 33 E 2 4 8 Brightness Adjustment When the CSC adjustment is performed the brightness changes slightly After performing the CSC adjust ment adjust the brightness again 1 Start the SRX Controller then click the SERVICE tab Refer to Section 2 1 3 The SERVICE sereen is displayed 2 Select the Gray 10 in Test Pattern Select of the COLOR SPACE CONVERTER SERVICE tab Screen example COLOR SPACE CONVERTER 3 Click the INSTALLATION tab Screen example F SRX T615 127 0 0 1 Bile LAMP POWER 4 Select an appropriate luminance level from the three levels in the LAMP POWER Level 3 is the brightest level 5 Perform the fine adjustment using and buttons 6 Check the brightness using the luminance meter 2 34 E SRX T615 2 5 Registration Adjustment Moves R red G green and B blue in the horizontal and vertical directions up to two pixels one pixel at a time so as to adjust registration For details refer to 5 SERVICE tab in Section 2 1 4 Also perform the fine adjustment of the registration in the image peripheral portion as required Refer to Section 2 5 1 2 5 1 Fine Adjustment of Registration First perform the adjustment of R G and B in
25. ed with the 3D lens filter 2 Attach the filter bracket B assembly with the two screws supplied with the 3D lens filter Eech PSW6 x 8 SS Filter bracket B assembly SRX T615 1 13 E 3 Attach the 3D filter R assembly with the two knobs 3D filter R assembly Knob 1 14 E 4 Release the lock plate in the direction of the arrow then hook it on the position pin 5 Attach the 3D filter L assembly with the two knobs Position pin 3D filter L assembly Lock plate SRX T615 1 15 E 1 5 Installation of Lamp For safety always wear gloves when performing installation 1 Loosen the screw with drop safe lower the two hooks and then remove the intake grille A in the direction of the arrow A Screw with drop safe Hooks Intake grille A Lamp door Lamp door latch 1 16 E SRX T615 3 Insert the lamp and close the lamp door e When holding the lamp be careful not to touch the connector contact portion Push near the PUSH mark of the lamp to insert it securely 4 Attach the remaining lamps by repeating steps 2 and 3 Connector contact portion 5 To install the intake grille A reverse the removal procedure SRX T6
26. en moving this unit to the pedestal after unpacking attach the carrying handles as required for trans porting it The carrying handles cannot be attached to both back forth and right left at the same time Parts information e Handle arm 4 164 849 02 4 pes e Pipe short 4 164 850 02 2 pcs Pipe long 4 164 851 02 2 pcs e M8 bolt 2 590 262 02 or 11 4 pcs In the case of attaching the pipe long to the right and left side of this unit 1 Loosen the nut in the direction of the arrow then insert the handle arm in the direction of the arrow 2 Tighten the nut to fix the handle arm 3 Attach the handle arm to the adjuster of other three portions by repeating steps and 2 gt X gt Ni SS Handle arm SRX T615 4 Insert the pipe long into the handle arms then fix the pipe with the two M8 bolts 5 Attach the pipe long on the other side in the same way M8 bolts Handle arm Pipe long Pipe long 1 6 E SRX T615 In the case of attaching the pipe short to the back and forth of this unit Tip The procedure is the same as the pipe long 1 Loosen the nut in the direction of the arrow then insert the handle arm in the direction of the arrow 8 2 Tighten the nut to fix the handle arm 3 Attach the handle arm to the adjuster of other three portions by repeating steps and 2 lt 35
27. ent 2 7 1 Edge Blending Setting When projecting the image using multiple projectors perform the edge blending adjustment to seamlessly connect the images from the projectors In this section an example using the two projectors is described e When performing the blending adjustment set the center adjustment points of the masking to 0 e Set the two projectors for blending adjustment as parallel as possible in the place vertical to the screen so that the image distortion does not occur Set to 0 in these portions Set the side or width that you want to perform blending as follows e Blending in horizontal direction Set Horizontal to Blending width 48 e Blending in vertical direction Set Vertical to Blending width 50 In this section an example of horizontal blending of the blending width 512 on the right side is explained 1 Start the SRX Controller then click the SERVICE tab Refer to Section 2 1 3 The SERVICE screen is displayed MASKING ADJUST EDGE BLENDING Screen example SERVICE tab ESO 0 3510 SRX T615 2 39 E 2 Double click the upper right adjustment point of MASKING ADJUST EDGE BLENDING The adjustment screen is displayed Screen example MASKING ADJUST EDGE BLENDING Adjustment screen 3 Enter 560 in Horizontal Setting value Blending width 512 48 560 4 Double click the lower right adjustment point Enter 560 in
28. ent point and adjust the horizontal and vertical directions using and buttons or by direct entry Setting value is increased Setting value is decreased Click to return to the original masking amount 2 4 6 Alignment of the Horizontal Position of Image for Right Eye and Image for 1 Left Eye Project a test pattern Frame Adjust Refer to steps 1 to 4 in Section 2 4 1 2 Click the Right radio button in Image Select of SINGLE 3D ADJUST Adjust the position of the image for the right eye in the horizontal direction in the H Adjust of the Position Adjust 3 SINGLE 3D ADJUST SRX T615 2 31 E Tip Also the image size in the horizontal direction H size image tilt in the horizontal direction H Tilt image tilt in the vertical direction V Tilt and the image shape in the vertical direction V Bow can be adjusted In the case of increasing H Tilt In the case of increasing V Tilt In the case of increasing V Bow 2 32 E SRX T615 2 4 7 Image Mapping When projecting the image from the server using the 3D lens it is required to set the image mapping according to the field angle of contents and the screen type 1 Open an INSTALLATION screen Refer to steps 1 to 3 in Section 2 4 1 INSTALLATION tab SINGLE 3D ADJUST 2 Select the image mapping corresponding to the type of contents the field angl
29. ft of lens shift block the images projected by the 2D lens and 3D lens cannot be adjusted to the same position because the image moves in the reverse direction due to the mechanism of this unit 1 Project a test pattern Frame Adjust Refer to steps 1 to 4 in Section 2 4 1 SINGLE 3D ADJUST 2 Click the L R Sync Left radio button in Image Select of SINGLE 3D ADJUST 3 Adjust the image position in the horizontal direction in H Adjust of Position Adjust 2 4 5 Position Adjustment Adjusting the Projector Tilt and Direction In the case that the V shift amount is insufficient adjust the length of foot in the rear portion of this unit to tilt the projector Refer to Section 1 7 In the case that the H shift amount is insufficient change this unit installation position in order to project the image obliquely Perform the mask processing because a keystone occurs when this unit is tilted 2 30 E SRX T615 Mask processing Open an INSTALLATION screen Refer to steps to 3 in Section 2 4 1 INSTALLATION tab 1 2 3 Screen example F SRX T615 127 0 0 MASKING ADJUST EDGE BLENDING 1 DOSEN SINGLE 3D ADJUST Click the L R Sync Left radio button in Image Select of SINGLE 3D ADJUST Double click the adjustment point of the MASKING ADJUST EDGE BLENDING The adjustment screen is displayed 4 Adjust the masking amount Click the adjustm
30. ge is changed om o The zoom ratio varies depending on the field angle flat scope 16 9 of contents when zooming accord ing to the screen size Therefore it is required to correct the center position of image The adjustment of the image center position is performed using the SRX Controller Refer to Section 2 3 2 Since the adjustable tolerance in the vertical and horizontal directions varies depending on the field angle of con tents it needs to be corrected in the following procedure When you want to perform the V shift adjust the image position with flat vertically longest field angle then correct the image center position with other field angles scope HD When you want to perform the H shift adjust the image position with scope horizontally longest field angle then correct the image center position with other field angles flat HD 2 20 E SRX T615 About the maximum adjustment range The V shift and H shift with the lens shift block is realized by changing the area used in the round shaped lens Therefore the maximum adjustment range becomes as shown in the following illustration image On the other hand it is mechanically possible to adjust the V shift and H shift over the maximum adjust ment range The lens shift amount is indicated by the proportion assuming that the height or width of the projected image is 100 If the V shift or H shift is moved
31. he button The lower end moves in the lower direction button button Linearity V Changes the upper and lower ends of the image without moving the center of V vertical V The image expands in the upper direction with the f V button button Fix the center SRX T615 Bow H Changes the right and left ends of the image without mov ing the center of image H The upper and lower ends of the image moves in the right direction with the button button Tilt H Tilts the image without changing the horizontal distance of vertical lines of the image H The upper end of the image moves in the right direction with the button button Left Mid Area H Moves the image in the horizontal direction with the 1 4 portion of the left side image as the center The center and left end of the image do not move H The image moves in the left direction with the button H button Fix the center and left end SRX T615 Bow V Changes the upper and lower ends of the image without moving the center of the image V The right and left ends of the image moves in the upper direction with the button button Tilt V Tilts the image without changing the vertical distance of horizontal lines of the image V The upper right end of the imag
32. ion board 4 input Single 3D HDMI 1 L R 3D mode Single 3D HDMI 2 L R 3D mode Single 3D HDMI 1 L 2 R 3D mode e MASKING ADJUST EDGE BLENDING Adjusts the image masking according to the screen shape by the eight adjusting point respectively And adjustment value is displayed by pointing the cursor at each adjusting point 1 to 8 Screen example 1 5 2 a 3 7 6 RESET button BLENDING button SRX T615 2 3 E When an adjusting point is double clicked the adjustment screen is displayed Screen example MASKING ADJUST EDGE BLENDING Adjustment screen A setting value increases when you click the button A setting value decreases when you click the button The numeric value can also be entered directly Each setting value is as follows 1 to 4 H 0 to 2047 V 1023 to 1023 5 6 V 511 to 511 7 8 H 511 to 511 All items in a MASKING ADJUST EDGE BLENDING are returned to the factory setting when you click the RESET button The blending adjustment screen is displayed when you click the BLENDING button MAIN version 3 19 0600 or later For details refer to Section 2 7 MUTING Operates to close and open of the douser button Close the douser Muting condition button Open the douser e CUT OFF When a 3D lens is attached switch the output of image for right eye and left eye Status POWER Locatio
33. ironment LKRM U450 6 pcs 450 W LKRM U330 6 pcs 330 W Tip If all 6 pcs are not inserted this unit does not operate Regarding the selection of lamp contact your local Sony Sales Office Service Center Power cable Need to obtain the cable that matches the plug on the installation site LAN cable or RS 232C cable For personal computer connection Exhaust system Connect the duct to the duct connecting portion on the rear top panel for exhausting the heat inside this unit In the case of using the 8 inch duct the following exhaust air volume is required The exhaust air volume of 450 550 ft min 12 7 to 15 6 m min should be secured HDMI cable For External reproduction device connection Refer to 1 1 5 Connection Tool Carrying handle Screwdriver for installing the lamp Handle arm part number 4 164 849 02 Pipe short part number 4 164 850 02 Pipe long part number 4 164 851 02 Luminance meter CL 200 or the equivalent Colorimeter PR 650 or the equivalent Tripod For the colorimeter and illuminometer Hexagonal wrench For the 3D lens adjustment subtense 2 5 3 0 5 0 mm For the lens shift adjustment subtense 5 0 mm Spanner Subtense 8 mm supplied with the lens Subtense 24 mm for flexible leveler Subtense 30 mm for nut M20 Personal computer PC For SRX Controller connection For detail refer to Section 2 1 1
34. justment Perform the position adjustment using the lens shift block 1 Start the SRX Controller then click the INSTALLATION tab The INSTALLATION screen is displayed 2 Select a test pattern in TEST PATTERN INSTALLATION tab Screen example Right TEST PATTERN Loosen the three V shift lock screws and three H shift lock screws Adjust the image position in the vertical direction by rotating the V shift knob Adjust the image position in the horizontal direction by rotating the H shift knob Tighten the three V shift lock screws and three H shift lock screws Oy ge a V shift lock screws 3 pcs V shift knob H shift lock screws 3 pes H shift knob Lens shift block SRX T615 2 19 E Precaution for using the V shift and H shift with the lens shift block When using the V shift and H shift with the lens shift block be careful with the following The center position of the image is changed when zooming When the V shift or H shift of the lens shift block is used the center position of image is deviated when zooming When the V shift or H shift of the lens shift block is not used the center position of image is not changed Center position of image Image When the V shift or H shift of the lens shift block is used the center position of ima
35. lue decreases the image becomes dark but the power consumption decreases In this case however the power consumption decreases Clicking the button the numeric value in creases Clicking the button the numeric value decreases e Level1 Level2 Level3 Switches the luminance adjustment filter on the image Level 3 indicates the brightest state 2 6 E SRX T615 TEST PATTERN An image can be adjusted by projecting the test pattern built in this unit on the screen without inputting the signal from other equipment Each test pattern is as follows Off No test pattern Cross Hatch Cross Hatch Invert Checker Flag e Test Mode 1 Scope e Flat Dual 3D Single 3D The test patterns in Dual 3D and Single 3D are for 3D lens 4 SINGLE 3D ADJUST This item is for 3D lens DISTORTION ADJUST 2D DUAL 3D When the MAIN version is earlier than 3 12 0530 this menu button is not displayed Adjusts the image distortion when the images displayed by the two projectors are overlaid When you click the button the following screen is displayed LNote When you use the two projectors by placing them next to each other use the one as the reference projec tor and adjust the other projector to the reference projector Do not change the values of the reference projector except for Centering Adjust the reference projector only for Centering adjustme
36. n Name Lamp status Warning Info POWER button Puts this unit into the standby state Canceled using an button button Turns on the power e Location Displays the location Name Displays the owner name Lamp bulb The color changes according to the time of the lamp used 0 to 80 White 80 to 100 Yellow 100 or more Red e Warning Info Displays warning information 2 4 E SRX T615 2 PICTURE CONTROL tab Screen example SRX T615 127 0 0 1 Password Help LENDING UTING R CONFIG Ia Range PICTURE CONTROL tab 3 COLOR CONFIG tab COLOR CONFIG tab Screen example P SRX 1615 127 0 0 1 Eile Password Help DG LLATION SRX T615 2 5 E 4 INSTALLATION tab INSTALLATION tab Screen example O LENS CONTROL LAMP POWER Q TEST PATTERN 4 SINGLE 3D ADJUST DISTORTION ADJUST 2D DUAL 3D MAIN version 3 12 0530 or later LENS CONTROL Adjusts the image projected on the screen Zoom Adjusts the size of an image An image is expanded when you click the button It is reduced when you click the button Focus Adjusts a focus A focus is adjusted to the distance place when you click the button It is adjusted to the nearby place when you click the button LAMP POWER Lamp Power Can adjust the output of a light source lamp bulb in units of 0 1 between 80 and 100 When a numeric va
37. nd Other countries Ethernet is a registered trademark of Xerox Corporation Other system names product names and company names appearing in this manual are trademarks or registered trademarks of their respective holders SRX T615 Section 1 Installation 1 1 Outline 1 1 1 Installation Flow The installation procedure for this unit is shown in the flow chart For the details of each flow refer to the corresponding item Basically there is no problem even if Sections 1 2 to 1 5 are not performed in sequential order However do not connect the power cord in Section 1 6 before Sections 1 2 to 1 5 are completed Start the installation d Install this unit d Install the SRX Controller in a personal computer PC Refer to the Operating Instructions Set this unit Refer to Section 2 2 1 2 Installation of Duct 1 3 Installation of Lens 1 4 Installation of 3D Lens Filter In the Case of LKRA 005 1 5 1 6 1 7 Installation of Lamp Connection of Power Cord Adjustment of Projector Tilt Note Perform gamma and uniformity adjustments before installation when using only a 3D lens Only a 2D lens Only a 3D ers 2D and 3D 1 is used is used lenses are used Perform lens adjustment Perform gamma and uniformity Perform lens adjustment Refer to
38. nt Screen example Items Adjust each item by using the buttons SRX T615 2 7 E Function and operation of each item Description of illustration e The operation method is described by using the button When the button is clicked the image moves in the opposite direction of the button e H shows the horizontal direction and V shows the vertical direction The dashed line shows the original image and the solid line shows the image after it is changed The illustration is shown so that the change of image is easily recognized Therefore it is different from the actual operating range Centering Moves the entire image in parallel The image of the reference projector is adjusted Do not use Centering with the other projector H The image moves in the right direction with the button V The image moves in the upper direction with the button button EEE mn ERIE EF Hi Albo Linearity H Changes the distance between both ends of the image without moving the center of H horizontal H The image expands in the right direction with the button Fix the center button 2 8 E Size Changes the entire image size H The right end of the image moves in the right direction with the button The left end moves in the left direction V The upper end of the image moves in the upper direc tion with t
39. ove up to two pixels one pixel at a time when you click the button e V Pixels move in the vertical direction R Red pixels vertically move up to two pixels one pixel at a time when you click the button G Green pixels vertically move up to two pixels one pixel at a time when you click the button B Blue pixels vertically move up to two pixels one pixel at a time when you click the button CG LAMP CONTROL amp INFORMATION Changes the time of the lamp used and the number of lamps Lamp information can be exported when you click the button in LAMP and the button in the LAMP IMFORMATION screen Lamp Number Select Select the number of lamps e Change Mode Select When 2 or 3 is selected in Lamp Number Select the switching mode can be selected from Auto or Manual In the Auto mode select the interval time In the Manual mode select the lighting pattern in Lamp Select LNote When Auto is selected in Change Mode Select another lamp automatically lights in case that a lamp failure occurs Therefore the number of lamps is maintained at all times The function does not operate when 6 is selected in Lamp Number Select or when lamp power is defective SRX T615 2 11 E AIR FILTER TIMER Displays and resets the operation time of air filter Filter Timer Displays the operation time of the air filter on the panel duct e RESET button
40. over the maximum adjustment range the image degradation or vignetting lack of image in the outer edge portion may occur or the image center position may not be adjusted when zooming There is no problem to use them over the maximum adjust ment range if you understand these conditions However it is recommended to use them within the maxi mum adjustment range for ordinary purposes at ga gt 35 Method for checking if the V shift and H shift are within the maximum adjustment range H shift When completely aligned 0 no shift When deviated by about 2 mm 7 Maximum adjustment range V shift ie When completely aligned 0 no shift When deviated by about 5 5 mm 35 Maximum adjustment range SRX T615 2 21 E In the 2D lens and 3D lens the image position moves in the reverse direction when per forming the H shift When attaching the 3D lens after performing the H shift with the 2D lens the image moves to the opposite side due to the mechanism of this unit Because of this when you want to project the image to the same posi tion using the 3D lens after using the H shift with
41. ple I SRX 1615 127 0 0 1 None PICTURE CONTROL COLOR CONFIG INSTALLATION SERS Setting item 2 Click the setting item on the left side of the SETTING screen to display the item that you want to set 3 After setting the items click the APPLY button The setting is registered 2 14 E SRX T615 2 2 2 Owner Information The information on this unit is set arbitrarily setting Screen example f SRX 1615 127 0 0 1 BLENDING MUTING None Owner Projector APPLY Owner Information Owner Name Type the name of owner Organization Type the name of organization Projector Region Type the region that the unit is installed Location Type the installation location Name Type the arbitrary name Memo Type a memo SRX T615 2 15 E 2 2 3 Network The connection to the network is set Screen example SRX T615 127 0 0 1 None Left Pat Right G INSTALLATION SERVICE amp SETTING amp Mean sin FUNCTION gt ion em Internet Protocol TCP IP Network LAN Setting Internet Protocol TCP IP Select either one of the IPv4 or IPv6 in the Priority IPv4 Setting Obtain an IP address automatically Obtains the IP address automatically from DHCP Specify an IP address Sets the specified IP address When Specify an IP address is selected perform the setting in the following boxes IP Address T
42. rection is smaller than that of other adjustment portions in the horizontal direction This is not due to the abnormal state but because of the specification Note on using the 3D lens When adjusting the 3D image hide one lens at a time At that time not only the image but also the cursor moves reversely in both horizontal and vertical directions 6 Move the cursor to the portion other than the center of the image by clicking the e t El buttons 7 Adjust the image using the ES buttons in the same way as step 5 8 Repeat steps 6 and 7 to adjust all portions 9 When the adjustments of all portions are completed click Off of the radio button in Test Pattern 10 Click Off of the radio button in Zone Adjust If Zone Adjust was set to Off the image for fine adjustment does not disappear from the screen To disappear the image first set Test Pattern to Off then set Zone Adjust to Off 2 6 Color Space Conversion CSC Adjustment The color space of this unit can be corrected for each color reproduction range The CSC adjustment cannot be properly performed when gamma is misaligned It is recommended to perform gamma and uniformity adjustments in advance Perform the gamma adjustment of this unit using a gamma adjustment tool PCAB G e Perform gamma and uniformity adjustments before CSC adjustment when changing the number of lamps The color may subtly vary depending on the number of lamps
43. screws Tightening torque 2 0 Nem Optical axis adjustment screw Optical axis adjustment lock screws 4 pcs Note The green light beam is output from the upper lens 2 26 E SRX T615 2 4 2 3D Lens Filter Adjustment In the Case of LKRA 005 In the LKRA 005 Installation Manual the procedure for installing LKRA 005 in SRX R320S is de scribed When installing LKRA 005 in this unit follow the procedure in this manual Adjust the position depth and vertical directions of the 3D lens filter so that the image is projected inside the frame by about cm Also adjust the tilt of 3D lens filter so that the light reflected by the 3D lens filter does not return to the lens Frame 3D lens filter Lens pe 1 cm Image 3D lens filter position depth direction adjustment 1 Loosen the knobs and position pins 2 Move the 3D lens filters in the depth direction 3 Tighten the knobs and position pins Position pins Position pins 3D lens filters SRX T615 2 27 E 3D lens filter position vertical direction adjustment 1 Remove the four adjustment screws 2 Move the 3D lens filters in the vertical direction by changing the attachment position of the adjust ment screws removed in step 1 Adjustment screws Adjustment screws A
44. the 2D lens it is required to return the image to the posi tion using the SRX Controller Refer to Section 2 3 2 Since the maximum value of H shift that can be performed by the SRX Controller when using the 3D lens is 7 the H shift with the lens shift block needs to be up to 3 5 taking into consideration the amount of H shift to be returned that was used by the 2D lens Method for checking if the H shift is 3 5 or less H shift ik When deviated by about 1 mm 3 5 2 3 2 Position Adjustment Electric Shift Using SRX Controller This adjustment is performed for adjusting the center position of image when zooming and so on in the case of using the V shift and H shift with the lens shift block 1 Click the INSTALLATION tab 2 Adjust the V Shift or H Shift using and buttons in the ELECTRIC SHIFT FUNCTION INSTALLATION tab Screen example BU NeaeRBFUNCTION2 ELECTRIC SHIFT FUNCTION 2 22 E SRX T615 2 3 3 Position Adjustment Adjusting the Projector Tilt and Direction In the case that the V shift amount is insufficient adjust the length of foot in the rear portion of this unit to tilt this unit Refer to Section 1 7 In the case that the H shift amount is insufficient change the projector installation position in order to project the image obliquel
45. ust ment and registration and calling of adjustment setting data FUNCTION MEMORY function are de scribed here Each adjustment is performed in a 3D mode Therefore install the 3D lens before adjustment when using 2D and 3D lenses jointly Perform gamma and uniformity adjustments using a Projector Color Adjustment Tool and 2D lens before image adjustment when using this unit by only a 3D lens This adjustment is not required when using this unit by only a 2D lens 2 4 1 Optical Axis Adjustment The optical axis in the 3D lens is adjusted so that the image for the left eye is projected from the lower lens and the image for the right eye is projected from the upper lens 1 Start the SRX Controller 2 Select Single 3D HDMI 1 L R Single 3D HDMI 2 L R or Single 3D HDMI 1 L 2 R in INPUT SELECT The current state enters a 3D mode 3 Click the INSTALLATION tab INPUT SELECT INSTALLATION tab TEST PATTERN 4 Click the Frame Adjust radio button in Single 3D of TEST PATTERN A test signal is displayed SRX T615 2 25 E 5 Loosen the four optical axis adjustment lock screws by two turns or more 6 Adjust so that the image for the left eye green image is projected from the lower lens and the image for the right eye magenta image is projected from the upper lens by rotating the optical axis adjust ment screw 7 Tighten the four optical axis adjustment lock
46. which Windows XP is installed to the projector Connection Connect this unit and PC using a LAN cable or RS 232C cable Left side of this unit When connecting using an RS 232C cable cross cable When connecting using a LAN cable PC SRX T615 2 1 E 2 1 3 Startup 1 Connect this unit and PC Refer to Section 2 1 2 2 Install SRX Controller Refer to the Operating Instructions 3 Start the SRX Controller Refer to the Operating Instructions Menu tab Screen example f SRX 1615 127 0 0 1 one 4 Click the menu tab to display the menu screen that you want to open 5 Ifyou want to display the SERVICE screen or the SETTING screen type the password in the password entering window and click the button Password Initial setting SERVICE screen service e SETTING screen setting Type the password using the lowercase characters To exit the menu Select Quit from the File menu 2 2 E SRX T615 2 1 4 Control Window 1 Common Items Screen example Die Password Help SCREEN CONTROL Status POWER Location Name Lamp status Warning Info Q SCREEN CONTROL INPUT SELECT Selects the input signal to be output as video signal HDMI 1 Internal HDMI input HDMI 2 Internal HDMI input AUX X1 Option board input AUX x4 Opt
47. y Perform the mask processing because a keystone occurs when this unit is tilted Mask processing 1 Double click the adjustment point in MASKING ADJUST of the MASKING ADJUST EDGE BLENDING The adjustment screen is displayed MASKING ADJUST EDGE BLENDING 2 Adjust the masking amount Click the adjustment point and adjust the horizontal and vertical directions using and buttons or by direct entry Setting value is increased S Setting value is decreased Click to return to the original masking amount SRX T615 2 23 E 2 3 4 Brightness Adjustment When the CSC adjustment is performed the brightness changes slightly After performing the CSC adjust ment adjust the brightness again 1 Start the SRX Controller then click the SERVICE tab Refer to Section 2 1 3 The SERVICE screen is displayed 2 Select the Gray 10 in Test Pattern Select of the COLOR SPACE CONVERTER SERVICE tab Screen example COLOR SPACE CONVERTER 3 Click the INSTALLATION tab INSTALLATION tab Screen example SRX T615 127 0 0 1 LAMP POWER 4 Select an appropriate luminance level from the three levels in the LAMP POWER Level 3 is the brightest level 5 Perform the fine adjustment using and buttons 2 24 E SRX T615 2 4 Image Adjustment 3D Lens The optical axis adjustment zoom adjustment focus adjustment position adjustment brightness adj
48. ype the IP address Subnet Mask Type the subnet mask Default Gateway Type the default gateway Primary DNS Type the IP address of primary DNS server Secondary DNS Option Type the IP address of secondary DNS server IPv6 Setting IPv6 Address Displays the automatically obtained global address Link Local IPv6 Address Displays the link local address Default Gateway Displays the automatically obtained default gateway Obtain a DNS server address automatically Sets whether automatically obtain a DNS server from DHCP server Specify a DNS server address Type the IPv6 address of DNS server when DNS server is not automatically obtained LAN Setting MAC Address Display the MAC address 2 16 E SRX T615 2 2 4 PC Communication The communication between this unit and PC is set Projector Identifyi Screen example Jee ONFIG STALLATION SERVICE amp SETTING amp FLMCTOH uncon o z z Network Block Reboot PC Communication Controlling PC Destination Projector Identifying Sets this unit Port No Type the UDP port number Interval Select the packet transmission interval Controlling PC Destination Sets the PC Port Nol Type the TCP port number Time out Select the time of the communication time out Network Block Reboot REBOOT button Click this button to reboot the network CPU After setting PC Communication a reboot of the network
Download Pdf Manuals
Related Search