INSTALLATION MANUAL INSTALLATION MANUAL
Contents
1. 10 Passive arming after closing the last door of the car the system produces a warning and 6 Functions description 1 2 3 4 Different siren sounds If they are allowed more then one the systems alarms altenate ly If any of sounds are allowed only sound is working 5 6 7 Tones for arming and disarming 5 Tones are with variable frequency 6 Tones are with constant frequency 7 Signalizing only with blinkers no tones If none of these functions are selected the tones are strong and short two for switching on three for switching off and one for accepted first code for disarming 8 Long blinkers if the function is enabled the blinkers lights 12sec after system disarming or till a door is opened or the ignition is turned on 9 Repeated self activation if the function is enabled the systems arms itself automatically 15sec after disarming on condition that no door is opened and the ignition is not turned on This way the system can t be disarmed by chance 10 Passive arming after closing the last door of the car the system produces a warning and 6 arms in 15 seconds 11 Disables and enables the current sensor 12 Warning for discarding the doors if the fuction is disabled the doors are ignored without any warning 13 Double code if the function is disabled the system can be disarmed only with button N1 14 Disabling the immobilizer if the function is enabled the ignition will be automatically2. M6 S S SATURN M6 X1 X1 11 11 stays in mode of learning of a new remote control transmitter Note 1 When washing the car motor you risk to wet the siren In such cases the guarrantee of the alarm system is not valid 2 If the transmission range of the remote control transmitter is too low battery change is rec ommended 3 The function programming should be done from a trained adjuster on the contrary you risk to damage some electric modules in the car 10 stays in mode of learning of a new remote control transmitter Note 1 When washing the car motor you risk to wet the siren In such cases the guarrantee of the alarm system is not valid 2 If the transmission range of the remote control transmitter is too low battery change is rec ommended 3 The function programming should be done from a trained adjuster on the contrary you risk to damage some electric modules in the car 10 again for leaving the self test mode and entering the mode of programming the first shock sen sor zone release the service button With N1 you increase the sensitivity and with N2 decrease it The degrees of sensitiveness are 16 and when you reach the end of each corresponding direc tion the system produces a long tone You can try the adjusment at any moment By pressing of both buttons together you go to the second zone Testing and adjustment you can do in the same way but the most sensitive degree is equal to
3. first zone When you adjust the second zone and on a light strike on the car only the first zone is activated the system produces just one short chirp If the second zone of the sensor is activated the system produces a long and short signal To exit the mode of adjustment of the shock sensor press again the both buttons of the remote control together At any moment on turning the ignition on by the key switch you leave the pro gramming adjustment mode Programmable functions To enter the programming mode press at first N1 you enter self test mode Press and hold the service button then press N1 again you leave the self test mode and can start programming the first function Release the service button again for leaving the self test mode and entering the mode of programming the first shock sen sor zone release the service button With N1 you increase the sensitivity and with N2 decrease it The degrees of sensitiveness are 16 and when you reach the end of each corresponding direc tion the system produces a long tone You can try the adjusment at any moment By pressing of both buttons together you go to the second zone Testing and adjustment you can do in the same way but the most sensitive degree is equal to first zone When you adjust the second zone and on a light strike on the car only the first zone is activated the system produces just one short chirp If the second zone of the sensor is activated the system produces a long and sh
4. re stored when you turn the ignition key on and if the system is disarmed 15 Locking and unlocking impuls term if it is yes the term is 3 5sec for pneumatic locking 16 Long lock if itis yes the locking impulse term is 24 sec as if it is does not work while lock On ignition turning on is enabled Also ff the function is enabled the shock and current sensors are switched off for 30sec after test time expiring 17 Additional channel for windows roll up control If the function is allowed the additional chan nel will supplies GNDduring test period 20 sec During the rest of time the channel can be activated by pressing button N3 you can roll up electric car windows manually and automati cally If the function is enabled the shock and current sensors are switched off for 30sec after test time expiring 7 arms in 15 seconds 11 Disables and enables the current sensor 12 Warning for discarding the doors if the fuction is disabled the doors are ignored without any warning 13 Double code if the function is disabled the system can be disarmed only with button N1 14 Disabling the immobilizer if the function is enabled the ignition will be automatically re stored when you turn the ignition key on and if the system is disarmed 15 Locking and unlocking impuls term if it is yes the term is 3 5sec for pneumatic locking 16 Long lock if itis yes the locking impulse term is 24 sec as if it
5. Car Alarm System Saturn 4 Brown ignition cut off E zi S A T U R N M 6 3 White door 4 White door p YelowGreen ACC 6 Blue GND 2 I LED 9 Violet additional channel 10 Grey siren 11 Brown ignition cut off 12 Red Black unlocking normally closed 13 Blue Black unlocking common 14 Grey Black unlocking normally opened 15 Green locking normally closed 16 Green Black locking common 17 Brown Black locking normally opened 18 Red 12V power on 19 Yellow indicator lights 20 Yellow indicator lights The second cable of the siren is connected to GND INSTALLATION MANUAL Car Alarm System Saturn al Brown ignition cut off e S A T U R N M 6 3 White door 4 White door 5 Yellow Green ACC 6 Blue GND I LED 9 Violet additional channel 10 Grey siren 44 Brown ignition cut off 12 Red Black unlocking normally closed 13 Blue Black unlocking common 14 Grey Black unlocking normally opened 15 Green locking normally closed 16 Green Black locking common 17 Brown Black locking normally opened 18 Red 12V power on 19 Yellow indicator lights 20 Yellow indicator lights The second cable of the siren is connected to GND INSTALLATION MANUAL INSTALLATION Instalation of the central unit Always instal the central inside the car s compartment at diff
6. ff the LED lights on for a short interval and if it is switched on the LED lights off for short Function switching on is done with N1 and its switching off with N2 A single function can be swithed on and off repeatedly and the next function follows by short turn ing the ignition key on the system emits one signal If you hold the ignition key on for more than 3 sec the system exit the pragromming mode After function 22 or if you stay at one and same function for more than 30 sec the system also leaves the programming mode by producing 3 signals 5 Functions description 1 2 3 4 Different siren sounds If they are allowed more then one the systems alarms altenate ly If any of sounds are allowed only sound is working 5 6 7 Tones for arming and disarming 5 Tones are with variable frequency 6 Tones are with constant frequency 7 Signalizing only with blinkers no tones If none of these functions are selected the tones are strong and short two for switching on three for switching off and one for accepted first code for disarming 8 Long blinkers if the function is enabled the blinkers lights 12sec after system disarming or till a door is opened or the ignition is turned on 9 Repeated self activation if the function is enabled the systems arms itself automatically 15sec after disarming on condition that no door is opened and the ignition is not turned on This way the system can t be disarmed by chance
7. he system produces a signal and enters the learning mode release the service button Then press twice a button of the remote control transmitter that should be learned in that way you have learned it the system produces a signal for disarming If you want to erase all remote control transmitters on entering the learning mode don t release the service button after 10 seconds the system emits one signal and all remote control transmitters are erased the system 9 18 Pager channel if the function is enabled and the channel is activated when the system alarms without warning it is used for activation of additional devices pager or GSM module The activation by pressing button N3 proceeds in the same way the device can be tested with out alarming If function 17 is enabled both functions 17 and 18 work together the additional channel will be activated in the test time and by the siren that s why if it is necessary to use one of 17 or 18 functions 19 Locking on turning the ignition on in activation of this function the system gives a locking impulse on turning the ignition on and gives unlocking impulse on turning the ignition off 20 Locking on passive arming if the function is disabled the system will not give a locking im pulse on passive arming func 10 but locks the car on arming by the remote control transmitter or by fuction 9 This function avoids the locking of your keys inside the car but decreases the rel
8. iability 21 Double unlocking this function allows generating two impulses when unlocking It is used in cars in which the first impuls unlocks only the drivers door and the second all others 22 Disabling the current sensor in Special mode when this function is allowed the currens sensor does not work in special mode it is used when the car has problems with the electri 18 Pager channel if the function is enabled and the channel is activated when the system alarms without warning it is used for activation of additional devices pager or GSM module The activation by pressing button N3 proceeds in the same way the device can be tested with out alarming If function 17 is enabled both functions 17 and 18 work together the additional channel will be activated in the test time and by the siren that s why if it is necessary to use one of 17 or 18 functions 19 Locking on turning the ignition on in activation of this function the system gives a locking impulse on turning the ignition on and gives unlocking impulse on turning the ignition off 20 Locking on passive arming if the function is disabled the system will not give a locking im pulse on passive arming func 10 but locks the car on arming by the remote control transmitter or by fuction 9 This function avoids the locking of your keys inside the car but decreases the reliability 21 Double unlocking this function allows generating two impulses when unlocki
9. icult of access and safety place The level of temperature vibrations and wetness must be minimum there Comfortable places for mounting are under the panel behind the drawer and other panels Cable connection All system cables must be connected reliably to the corresponding cables of the car by connec tors or sticking and have to be isolated with qualitative izolirband or shrinkable folio Take care to the connections to ground Adjustment of the shock sensor To adjust the both zones of the shock sensor press N1 you enter the self test mode press N2 for enetring the special security mode Press and hold the service button then press button N1 2 INSTALLATION Instalation of the central unit Always instal the central inside the car s compartment at difficult of access and safety place The level of temperature vibrations and wetness must be minimum there Comfortable places for mounting are under the panel behind the drawer and other panels Cable connection All system cables must be connected reliably to the corresponding cables of the car by connec tors or sticking and have to be isolated with qualitative izolirband or shrinkable folio Take care to the connections to ground Adjustment of the shock sensor To adjust the both zones of the shock sensor press N1 you enter the self test mode press N2 for enetring the special security mode Press and hold the service button then press button N1 2 SATURN
10. is does not work while lock on ignition turning on is enabled Also ff the function is enabled the shock and current sensors are switched off for 30sec after test time expiring 17 Additional channel for windows roll up control If the function is allowed the additional chan nel will supplies GNDduring test period 20 sec During the rest of time the channel can be activated by pressing button N3 you can roll up electric car windows manually and automati cally If the function is enabled the shock and current sensors are switched off for 30sec after test time expiring 7
11. ng It is used in cars in which the first impuls unlocks only the drivers door and the second all others 22 Disabling the current sensor in Special mode when this function is allowed the currens sensor does not work in special mode it is used when the car has problems with the electri 15 Locking time 3 5 0 7cek no 16 Long lock no 17 Channel for windows roll up no 18 Pager channel no 19 Locking on ignition switching on no 20 Locking on passive arming yes 21 Double unlocking no 22 Disabling the current sensor in Special mode no If the function is switched off the LED lights on for a short interval and if it is switched on the LED lights off for short Function switching on is done with N1 and its switching off with N2 A single function can be swithed on and off repeatedly and the next function follows by short turn ing the ignition key on the system emits one signal If you hold the ignition key on for more than 3 sec the system exit the pragromming mode After function 22 or if you stay at one and same function for more than 30 sec the system also leaves the programming mode by producing 3 signals 5 15 Locking time 3 5 0 7cek no 16 Long lock no 17 Channel for windows roll up no 18 Pager channel no 19 Locking on ignition switching on no 20 Locking on passive arming yes 21 Double unlocking no 22 Disabling the current sensor in Special mode no If the function is switched o
12. ort signal To exit the mode of adjustment of the shock sensor press again the both buttons of the remote control together At any moment on turning the ignition on by the key switch you leave the pro gramming adjustment mode Programmable functions To enter the programming mode press at first N1 you enter self test mode Press and hold the service button then press N1 again you leave the self test mode and can start programming the first function Release the service button 1 Sound1 yes 2 Sound2 no 3 Sound3 no 4 Sound4 no 5 Chirps1 yes 6 Chirps2 no 7 Chirps3 no 8 Long blinkers no 9 Repeated self activation no 10 Passive arming no 11 Current sensor yes 12 Warning for door ignoring yes 13 Double code yes 14 Disabling the immobilizer no 4 1 Sound1 yes 2 Sound2 no 3 Sound3 no 4 Sound4 no 5 Chirps1 yes 6 Chirps2 no 7 Chirps3 no 8 Long blinkers no 9 Repeated self activation no 10 Passive arming no 11 Current sensor yes 12 Warning for door ignoring yes 13 Double code yes 14 Disabling the immobilizer no 4 cal installation or the battery which are leading to a fake produce of the current sensor Due to that the client can turn on the alarm of the car in special mode without running the risk of fake produces Additional channel The pressing of button N3 activates the additional channel for the term of buttons pressing and sup
13. plies GNDI up to 0 5A If the system is in armed mode both shock and the current sensor are ignored inactivated for 30sec The channel can be activated also by functions 17 and 18 Learning mode of a new remote transmitter Press and hold the service VALET button The car ignition should be switched on and off 4 times the system produces a signal and enters the learning mode release the service button Then press twice a button of the remote control transmitter that should be learned in that way you have learned it the system produces a signal for disarming If you want to erase all remote control transmitters on entering the learning mode don t release the service button after 10 seconds the system emits one signal and all remote control transmitters are erased the system 9 cal installation or the battery which are leading to a fake produce of the current sensor Due to that the client can turn on the alarm of the car in special mode without running the risk of fake produces Additional channel The pressing of button N3 activates the additional channel for the term of buttons pressing and supplies GNDI up to 0 5A If the system is in armed mode both shock and the current sensor are ignored inactivated for 30sec The channel can be activated also by functions 17 and 18 Learning mode of a new remote transmitter Press and hold the service VALET button The car ignition should be switched on and off 4 times t
Download Pdf Manuals
Related Search