Home

User Manual

Contents

1. 18 Section 3 Configuration Wireless Client Mode This wizard is designed to assist you in configuring your DAP 1665 as a wireless client Select Wireless Client from the drop down menu ari car Veen Ca A Please select wireless mode Click Next to continue i Allows your Ethernet enabled device acts as a Wireless Mode Wireless Client ireless adapter Wirekess Aouler DAP 1665 in Wireless Client Mode Select WPS as the configuration method only if your SELECT CONFIGURATION METHOD wireless device supports Wi Fi Protected Setup WPS Please select one of the following configuration methods and click next to R continue For Manual setup skip to page 21 WPS Select this option if you want to use WiFi Protected Setup Manual Select this option if you want to setup your network manually Click Next to continue Press the WPS Push Button on your existing wireless A SE F router with 120 seconds to complete the WPS setup Process Please press the Push Button physical or virtual on the AP or Router you are connecting to within 111 seconds D Link DAP 1665 User Manual 19 Section 3 Configuration Ifa connection has been successfully made click Finish ADD WI FI DEVICE WITH WPS on the following screen to complete the setup process If the connection was not successful click Retry to try You have successfully connected ta the Wi Fi network again or Cancel to abort the setup process Finish
2. ADD WI FI DEVICE WITH WPS You have failed to connect to the Wi Fi network within the given timeframe please click on the button below to do it again Retry D Link DAP 1665 User Manual 20 Section 3 Configuration Select Manual configuration to setup your network manually Click Next to continue Locate the SSID of the wireless network that you wish to connect to from the list Select it by clicking on the radio button in the far right column Click Connect at the bottom of the page to continue If you do not see your network in the list click Rescan to search again If the existing wireless network uses wireless security enter the Wi Fi Password in the field provided Click Next to continue D Link DAP 1665 User Manual SELECT CONFIGURATION METHOD Please select one of the following configuration methods and click next to continue O WPS Select this option if you want to use WiFi Protected Setup SELECT WI FI NETWORK WPA PSK 07869 5 00 18 e7 95 68 ab 48 A N AP aes tkip WPA2 100 PSK aes tkip D Link 1c bd b9 c3 8f 40 149 A N AP no 71 WPA PSK SWSWSW 00 94 e4 cd d8 06 157 A N AP aes tkip WPA2 67 PSK aes tkip dlink1 fc 75 16 76 73 00 149 A N AP no 65 dlink fc 75 16 76 73 01 149 A N AP no 63 ENTER WI FI PASSWORD Please enter Wi Fi Password to establish wireless connection Wi Fi Password 21 Section 3 Configuration A dialog box will appear asking if you wish
3. Click Add Wireless Device With WPS to activate the WPS PBC Push button method You will then have 120 seconds to press the WPS button on the new device that you wish to connect Click Save Settings at the top of the page to save the current configuration D Link DAP 1665 User Manual WIFI PROTECTED SETUP ALSO CALLED WCN 2 0 IN WINDOWS VISTA Enable Disable WPS PIN Method Reset to Unconfigured PIN SETTINGS Current PIN 63010923 ADD WIRELESS STATION Reset PIN to Default Generate New PIN Add Wireless Device With WPS 59 Section 3 Configuration User Limit Here you can set a maximum number of users that can be connected to the access point at any one time Enable User Check the box to enable the user limit function Se SSeS Limit User Limit Enter a number of users between 1 32 User Limit 1 32 Click Save Settings at the top of the page to save the current configuration D Link DAP 1665 User Manual 60 Section 3 Configuration Maintenance The Maintenance section allows you to adjust the administrative settings of the router such as time and date administrator password and update the device s firmware Admin New Password To change the password for the web based configuration utility s Admin account enter a new password in the field provided New Password ssssssss PASSWORD Confirm Password ssssssss Confirm Re enter the new password in this field
4. D Link DAP 1665 User Manual 2 4GHZ ADVANCED WIRELESS SETTINGS Transmit Power 100 WMM Enable Short GI IGMP Snooping WLAN Partition HT 20 40 Coexistence M M E Enable Disable 50 Section 3 Configuration 5 GHz Band Transmit Power Select the desired transmission power of the wireless radio from HER the drop down menu Transmit Power 100 WMM Enable Wireless Multimedia WMM is a QoS engine which can help to se reduce lag and latency when transmitting multimedia over your Short GI wireless connection This is permanently enabled IGMP Snooping E WLAN Partition Short GI Enabling a short Guard Interval GI can increase throughput However it can also increase error rate in some installations due to increased sensitivity to radio frequency reflections Select the option that works best for your installation IGMP Snooping Enabling this option allows the access point to listen for Internet Group Management Protocol IGMP traffic which can help to detect clients which require multicast streams WLAN Partition Enabling this option means that connection wireless clients will not be able to communicate with one another but will still have access to network resources such as the Internet Click Save Settings at the top of the page to save the current configuration D Link DAP 1665 User Manual 51 Section 3 Configuration Wi Fi Protected Setup This section al
5. Auto 20 40 80MHz 1 3 5 7 WPA2 PSK AES Note The Bridge with AP mode is not completely specified in the Wi Fi or IEEE standards This mode will work with other DAP 1665 units Communication with other APs even other D Link APs is not guaranteed D Link DAP 1665 User Manual 33 Section 3 Configuration 2 4 GHz Band Note If the Bridge Band is set to 2 4 GHz the settings for AP s 2 4 GHz band will be the same as those for the bridge and only the SSID and visibility status of the 2 4 GHz band can be changed Enable Wireless Wireless Network Name 802 11 Mode Wireless Channel Enable Auto Channel Scan Channel Width Check the box to enable the wireless function for the 2 4 GHz band If you do not want to use wireless uncheck the box to disable all wireless functions You may also set up a specific time range schedule Select a schedule from the drop down menu or click Add New to create a new schedule By default the schedule is set to Always Specify a network name SSID to identify the 2 4 GHz network This is the network name that wireless clients will search for when connecting to your wireless network Select one of the following 802 11n Only Select if you are only using 802 11n wireless clients Mixed 802 11n and 802 119 Select if you are using a mix of 802 11n and 802 11g wireless clients Mixed 802 11n 802 11g and 802 11b Select if you are using a mix of 802 11
6. Section 3 Configuration Wireless Client Mode Advanced Wireless 2 4 GHz Band Transmit Power Select the desired transmission power of the wireless radio from AGHZ ADVANCED WIRELESS SETTINGS the drop down menu Transmit Power 100 HT 20 40 Enable this option to reduce interference from other wireless HT 20 40 Coexistence Enable Disable Coexistance networks in your area If the channel width is operating at 40 MHz and there is another wireless network s channel over lapping and causing interference the router will automatically change to 20 MHz Click Save Settings at the top of the page to save the current configuration 5 GHz Band Transmit Power Select the desired transmission power of the wireless radio from EPPP the drop down menu Click Save Settings at the top of the page to save the current configuration D Link DAP 1665 User Manual 54 Section 3 Configuration Bridge Mode Access Control Mac filtering allows you to control wireless access to your network according to clients MAC addresses Configure MAC Filtering Checkbox MAC Address Use the drop down menu to select your desired MAC filtering method Turn MAC Filtering OFF No MAC filtering will be implemented Turn MAC Filtering ON and ALLOW MAC filtering will be turned on and only MAC addresses listed in the table below will be allowed access Turn MAC Filtering ON and DENY MAC filtering will be turned
7. This wizard is designed to assist you in your Wi Fi network setup It will guide you through step by step instructions on how to set up your Wi Fi network and how to make it secure 16 Section 3 Configuration Access Point Mode This wizard is designed to assist you in configuring your DAP 1665 as an access point Select Access Point from the drop down menu Then click Next to continue This screen will help you to set a network name SSID and security password for your wireless network Specify an SSID for both the 2 4 GHz and 5 GHz bands these names must not be the same If you wish to use the Same wireless security password for both networks check the box and enter your desired password in the field provided If you wish to use a different password for each network uncheck the box and enter the desired passwords in the 2 4 GHz Wi Fi Password and 5 GHz Wi Fi Password fields Click Next to continue D Link DAP 1665 User Manual SELECT YOUR OPERATION MODE Please select wireless mode Click Next to continue Access Point allows the device to act as the wireless transmitter for your router or become a separate Access Point Wireless PC Router e tla DAP 1665 in Access Point Mode Wireless Mode Access Point Wireless PC WELCOME TO THE D LINK WI FI SETUP WIZARD Give your Wi Fi network a name 2 4GHz Wi Fi Network Name SSID dlink 96C 1 using up to 32 characters 56Hz Wi Fi Netw
8. 1 Open the Windows XP Wireless Utility by right clicking on the wireless computer icon in your system tray lower right corner of screen Select View Available Wireless Networks Repair View Available Wireless Networks Change Windows Firewall settings 2 Highlight the wireless network SSID you would like to connect to i Wireless Network Connection 6 a nd cl ick Connect sictcesh Ta Choose a wireless network 7 Refresh network list Click an item in the list below to connect to a wireless network in range or to get more information lt 2 Set up a wireless network o Test for a home or small office Unsecured wireless network all Related Tasks A default i Learn about wireless Unsecured wireless network anil networking salestest Security enabled wireless network all J testi preferred networks de Change the order of e Gp Change advanced settings A p Security enabled wireless network al il This network requires a network key If you want to connect to this network dick Connect DGL 4300 n Es D Link DAP 1665 User Manual 84 Section 5 Connecting to a Wireless Network 3 The Wireless Network Connection box will appear Enter the WPA PSK passphrase and click Connect It may take 20 30 seconds to connect to the wireless network If the connection fails please verify that the WPA PSK settings are correct The WPA PSK passphrase must be exactly the same as on
9. 802 11 Mode Mixed 802 11n 802 119 and 802 11b Wireless Channel 6 Security Mode For information on how to set up wireless security please refer Enable Auto Channel Scan M to Configuring Wireless Security on page 42 Channel Width Auto 20 40MHz Visibility Status Visible Invisible Click Save Settings at the top of the page to save the current configuration 2 4GHZ WIRELESS SECURITY SETTING Security Mode WPA Personal WPA Mode AUTO WPA or WPA2 Cipher Type AES Pre Shared Key password 5 GHz Band If the Bridge Band is set to 5 GHz the settings for AP s 5 GHz band will be the same as those for the bridge and only the SSID and visibility status of the 5 GHz band can be changed Enable Wireless Check the box to enable the wireless function for the 5 GHz RER band If you do not want to use wireless uncheck the box to disable all wireless functions You may also set up a specific Eana E Always time range schedule Select a schedule from the drop down Wireless Network Name dink 07DA 1GHz Also called the SSID menu or click Add New to create a new schedule By default 802 11 Mode Mixed 802 ilac 802 1in and 802 113 the schedule is set to Always Wireless Channel 36 Enable Auto Channel Scan Wireless Specify a network name SSID to identify the 5 GHz network Channel Width Auto 20 40 80MHz Network Name This is the network name that wireless clients will search for Visibility
10. SSID of your wireless network to be Visible or Invisible to wireless clients If Invisible the SSID of the DAP 1665 will not be seen by site survey utilities so wireless clients will have to manually enter the SSID of your wireless network in order to connect to it For information on how to set up wireless security please refer to Configuring Wireless Security on page 42 2 4GHZ WIRELESS NETWORK SETTINGS Enable Wireless Always Wireless Network Name diink 36C1 Also called the SSID 802 11 Mode Mixed 802 11n 802 ligand802 1ib Wireless Channel Enable Auto Channel Scan Channel Width Auto 20 40MHz Visibility Status Visible Invisible 2 4GHZ WIRELESS SECURITY SETTING 5 GHz Band Check the box to enable the wireless function for the 5 GHz band If you do not want to use wireless uncheck the box to disable all wireless functions You may also set up a specific time range schedule Select a schedule from the drop down menu or click Add New to create a new schedule By default the schedule is set to Always Specify a network name SSID to identify the 5 GHz network This is the network name that wireless clients will search for when connecting to your wireless network This name should be different to that of the 2 4 GHz network configured above D Link DAP 1665 User Manual GHZ WIRELESS NETWORK SETTINGS Enable Wireless Always Add New Wireless Network Name Also called the SSID 8
11. Safety amp Emissions e CE e IC FCC e Wi Fi Certified e TELEC e VCCI Dimensions e 47 x 108 x 27 8 mm 5 79 x 4 25 x 1 1 inches Weight e 222 grams 0 489 Ibs 1 Maximum wireless signal rate derived from IEEE Standard draft 802 11ac 802 11n and 802 11g specifications Actual data throughput will vary Network conditions and environmental factors including volume of network traffic building materials and construction and network overhead lower actual data throughput rate Environmental conditions will adversely affect wireless signal range All Maximum transmission power values expressed are for dual chain mode Maximum transmission power and included antennas may vary depending on regional regulations gt Range may vary depending on regional regulations D Link DAP 1665 User Manual 92 Appendix C Compliance Statements Compliance Statements Trademarks D Link is a registered trademark of D Link Corporation D Link Systems Inc Other trademarks or registered trademarks are the property of their respective owners Copyright Statement No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any derivative such as translation transformation or adaptation without permission from D Link Corporation D Link Systems Inc as stipulated by the United States Copyright Act of 1976 and any amendments thereto Contents are subject to change without
12. WINO a O O E 74 AAA ON a ENN 76 ARAONS VISTA a hi esate 79 D Link DAP 1665 User Manual PNR a an 80 RS NON a tes 82 Using Windows RP sn ru 83 Configure WPA PSK nn 84 TTOUDIeSROODENO Sins irerse 86 Networking Basics ccccscccssscccssscccssscccssscccssscccssscoesees 90 Check your IP address nn 90 Statically Assign an IP address 91 Technical Specifications cccsscccssscsccssscccssssccssssccsssscess 92 Compliance Statements ccsccccssccsssccscsccsssccssscoesscoeees 93 iii Section 1 Product Overview Product Overview Package Contents DAP 1665 Wireless AC1200 Dual Band Access Point Ethernet Cable Two Detachable Antennas Power Adapter CD ROM with Manual Note Using a power supply with a different voltage rating than the one included with the DAP 1665 will cause damage and void the warranty for this product The appearance of the external antennas may vary depending on region D Link DAP 1665 User Manual Section 1 Product Overview System Requirements e An Ethernet based Network e IEEE 802 11ac n g b a wireless clients AP Repeater Mode Network Requirements e IEEE 802 11ac n g b a wireless network Client Bridge Repeater Mode e 10 100 1000 Ethernet Computer with the following e Windows Macintosh or Linux based operating system e An installed Ethernet adapter Browser Requirements Web based Configuration e Internet Explorer 7 0 or higher Utility Requirements e Moz
13. on and only MAC addresses listed in the table below will be denied access Check the box to include this MAC address in the MAC filtering rules Enter the MAC address of the client that you wish to filter If the client is currently connected to the access point you can select it from the Client List drop down menu and click lt lt to automatically populate the field Click Clear to clear all fields Click Save Settings at the top of the page to save the current configuration D Link DAP 1665 User Manual ACCESS CONTROL SETTINGS Configure MAC Filtering below Turn MAC Filtering OFF T MAC Address Client List 55 Section 3 Configuration Bridge with AP Mode Advanced Wireless On this page you can adjust the advanced wireless settings for both the 2 4 GHz band and the 5 GHz band Settings for this mode are the same as for the Access Point Mode on page 28 except as noted below Transmit Power WMM Enable Short GI IGMP Snooping WLAN Partition HT 20 40 Coexistance Select the desired transmission power of the wireless radio from the drop down menu Wireless Multimedia WMM is a QoS engine which can help to reduce lag and latency when transmitting multimedia over your wireless connection This is permanently enabled Enabling a short Guard Interval GI can increase throughput However it can also increase error rate in some installations due to increased sensitivity to radio freque
14. 07725 Abo called the SSID 802 11 Band 2 4GHz 5GHz Channel Width Auto 20 40MHz 2 4GHZ WIRELESS SECURITY SETTING Security Mode WPAPersonal WPA Mode AUTO WPA or WPAZ Cipher Type TKIP and AES Pre Shared Key password WIRELESS MAC CLONE WIFI PROTECTED SETUP ALSO CALLED WCN 2 0 IN WINDOWS VISTA Enable Current PIN 26018539 Reset PIN to Default Generate New PIN 31 Section 3 Configuration Wireless Mode Bridge Band 802 11 Mode Wireless Channel Channel Width Remote AP MAC Bridge Security Bridge Mode Select Bridge from the drop down menu Select the wireless band that you wish to use for the wireless bridge 2 4 GHz The bridge can function using 802 11n 802 110 or 802 11g 5 GHz The bridge can function using 802 11ac 802 11n or 802 11a Select the appropriate 802 11 mode depending on which 802 11 standard you want the bridge to use Select the wireless channel that you want the bridge to use All APs on the bridge must be using the same wireless channel Select the appropriate channel width between 20MHz or Auto 20 40MHz from the drop down menu If you are using the 5 GHz band an additional Auto 20 40 80 option will be available Enter the MAC addresses of the APs in your network that will serve as bridges to wirelessly connect multiple networks Select the desired wireless security method from the drop down menu If you select WEP y
15. Channel Width Auto 20 40 80 MHz Select this option if you are using a combination of 802 11ac 802 11n and other wireless devices Auto 20 40 MHz Select if you are using both 802 11n and non 802 11n wireless devices 20 MHz Select if you are not using any 802 1 1n wireless clients Select whether you would like the network name SSID of your wireless network to be Visible or Invisible to wireless clients If Invisible the SSID of the DAP 1665 will not be seen by site survey utilities so wireless clients will have to manually enter the SSID of your wireless network in order to connect to it For information on how to set up wireless security please refer to Configuring Wireless Security on page 42 Click Save Settings at the top of the page to save the current configuration D Link DAP 1665 User Manual GHZ WIRELESS NETWORK SETTINGS Enable Wireless Wireless Network Name 802 11 Mode Wireless Channel Enable Auto Channel Scan Channel Width Auto 20 40 80MHz Visibility Status Visible Invisible Always dlink 07D A 5GHz Also called the SSID Mixed 802 11ac 802 iin and 802 1ia 36 F 5GHZ WIRELESS SECURITY SETTING Security Mode WPAPersonal WPA Mode AUTO WPA or WPAZ Cipher Type AES Pre Shared Key password 36 Section 3 Configuration Repeater Mode Repeater mode re broadcasts the wireless signal of an existing network to increase coverage The exi
16. Fi Protected Access WPA WPA2 WPA Personal WPA Enterprise What is WEP Wired Equivalent Privacy WEP is an older form of wireless encryption which operates only in 802 11g legacy mode WEP uses hex digits to create an authentication key and is considered to be less secure than the newer WPA WPA2 security standards It is recommended that you only use this security mode if your wireless clients do not support WPA WPA2 What is WPS Wi Fi Protected Setup WPS allows you to quickly and easily create a secure wireless connection between devices using a push button or a PIN code This method alleviates the need for users to change settings on their wireless devices or remember security passwords Many wireless devices have a physical push button located somewhere on the exterior casing while others may have a software button located within the device s configuration software Please refer to your wireless device s documentation for further information on how to connect to the DAP 1665 using WPS D Link DAP 1665 User Manual 72 Section 4 Security What is WPA WPA or Wi Fi Protected Access is a Wi Fi standard that was designed to improve the security features of WEP Wired Equivalent Privacy The 2 major improvements over WEP e Improved data encryption through the Temporal Key Integrity Protocol TKIP TKIP scrambles the keys using a hashing algorithm and by adding an integrity checking feature ensures that the keys have
17. Status Visible Invisible when connecting to your wireless network This name should be different to that of the 2 4 GHz network configured above 5GHZ WIRELESS SECURITY SETTING Security Mode WPAPersonal WPA Mode AUTO WPA or WPAZ Cipher Type AES Pre Shared Key password D Link DAP 1665 User Manual 35 Section 3 Configuration 802 11 Mode Wireless Channel Enable Auto Channel Scan Channel Width Visibility Status Security Mode Select one of the following 802 11a Only Select if you are only using 802 11a wireless clients 802 11n Only Select if you are only using 802 11n wireless clients Mixed 802 11n and 802 11a Select if you are using a mix of 802 11n and 802 11a wireless clients 802 11ac Only Select if you are only using 802 1 1ac wireless clients Mixed 802 1 1ac and 802 1 1n Select if you are using a mix of 802 11ac and 802 11n wireless clients Mixed 802 1 1ac 802 11n and 802 1 1a Select if you are using a mix of 802 11ac 802 11n and 802 1 1a wireless clients Indicates the channel setting for the DAP 1665 The Channel can be changed to fit the channel setting for an existing wireless network or to reduce interference in congested areas If you enable Auto Channel Scan this option will not be available The Auto Channel Scan setting can be selected to allow the DAP 1665 to automatically choose the channel with the least amount of interference Select the
18. aux appareils radio exempts de licence L exploitation est autoris e aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible d en compromettre le fonctionnement Caution i the device for operation in the band 5150 5250 MHzis only for indoor use to reduce the potential for harmful interference to co channel mobile satellite systems ii high power radars are allocated as primary users i e priority users of the bands 5250 5350 MHz and 5650 5850 MHz and that these radars could cause interference and or damage to LE LAN devices Avertissement i les dispositifs fonctionnant dans la bande 5 150 5 250 MHz sont r serv s uniquement pour une utilisation l int rieur afin de r duire les risques de brouillage pr judiciable aux syst mes de satellites mobiles utilisant les m mes canaux ii De plus les utilisateurs devraient aussi tre avis s que les utilisateurs de radars de haute puissance sont d sign s utilisateurs principaux c a d qu ils ont la priorit pour les bandes 5 250 5 350 MHz et 5 650 5 850 MHz et que ces radars pourraient causer du brouillage et ou des dommages aux dispositifs LAN EL D Link DAP 1665 User Manual 94 Appendix C Compliance Statements IMPORTANT NOTE Radiation Exposure Statement This equipment complies with IC radiation exposure limits set
19. listen for Internet Group Management Protocol IGMP traffic which can help to detect clients which require multicast streams Enabling this option means that connection wireless clients will not be able to communicate with one another but will still have access to network resources such as the Internet Enable this option to reduce interference from other wireless networks in your area If the channel width is operating at 40 MHz and there is another wireless network s channel over lapping and causing interference the router will automatically change to 20 MHz Click Save Settings at the top of the page to save the current configuration D Link DAP 1665 User Manual ADVANCED WIRELESS SETTINGS Transmit Power WMM Enable Short GI IGMP Snooping WLAN Partition HT 20 40 Coexistence 58 Section 3 Configuration Wi Fi Protected Setup This section allows you to configure how the DAP 1665 uses Wi Fi Protected Setup WPS to create a secure wireless connection Enable Check the box to enable WPS Disable WPS PIN Check the box to disable WPS using the PIN method If this Method option is selected wireless clients will only be able to use the WPS PBC Push button Connection method Current PIN Displays the current PIN which can be used by wireless clients to connect to the access point Click Reset PIN to Default to return the PIN to its factory default Click Generate New PIN to randomly generate a new PIN
20. next to the time Select Connect to a network sil dfs FMI Ty Ct Friday A 3 17 2007 The utility will display any available wireless networks in your area Click on a network displayed using the SSID and click the Connect button ww La Connect to a network Disconnect or connect to another network Show All 1 If you get a good signal but cannot access the Internet check your TCP IP settings of your wireless adapter Refer to the Networking Basics section in this manual for more information Unsecured network x tuesday Security enabled network Set up a connection or network Open Network and Sharing Center Css D Link DAP 1665 User Manual 79 Section 5 Connecting to a Wireless Network WPA WPA2 It is recommended to enable wireless security WPA WPA2 on your wireless router or access point before configuring your wireless adapter If you are joining an existing network you will need to know the security key or passphrase being used 1 Open the Windows Vista Wireless Utility by right clicking on the Not Connected wireless computer icon in your system tray lower right corner of BG Wireless networks are available screen Select Connect to a network Connect to a network Network and Sharing Center LL Li oF lvl val y Co Friday 8 17 2007 2 Highlight the Wi Fi name SSID you would like to connect to and click Connect wy i Connect to a network D
21. primary DNS server address to be used by the access point Static IP only Enter the secondary DNS server address to be used by the access point Static IP only Click Save Settings at the top of the page to save the current configuration DEVICE NAME Device Name allows you to configure this device more easily You can enter http device name into your web browser instead of IP address for configuration Default http dlinkap LAN IPV4 CONNECTION TYPE Choose the IPv4 mode to be used by the Access Point My LAN Connection is Dynamic IP DHCP DYNAMIC IP DHCP LAN CONNECTION TYPE IP Address Information IP Address Subnet Mask Gateway Address Primary DNS Server 45 Section 3 Configuration DHCP Server The access point has a built in Dynamic Host Control Protocol DHCP server which can automatically assign IP addresses to connected clients that request them The DHCP server function will only be available when Static IP Address mode is used Enable DHCP Server DHCP IP Address Range Always Broadcast Gateway WINS DNS DHCP Lease Time Dynamic DHCP Client List Check the box to enable the DHCP server function Enter the range of the DHCP address pool from which requesting clients can be assigned addresses You should ensure that the access point s static IP address is outside of this range in order to avoid any IP address conflicts Check the box to have the D
22. the 5 GHz wireless band If you do not want to use wireless uncheck the box to disable all wireless functions You may also set up a specific time range schedule Select a schedule from the drop down menu or click Add New to create a new schedule By default the schedule is set to Always Displays the name of the network which is to be repeated Choose how you would like to name the DAP 1665 s extended network using the radio buttons Same as Repeater Name The extended network will have the same name SSID as the repeater network Create a New Wi Fi Network Name Enter a new name SSID for the extended network in the field below Select one of the following 802 11a Only Select if you are only using 802 11a wireless clients 802 11n Only Select if you are only using 802 11n wireless clients Mixed 802 11n and 802 11a Select if you are using a mix of 802 11n and 802 11a wireless clients 802 11ac Only Select if you are only using 802 1 1ac wireless clients Mixed 802 1 1ac and 802 1 1n Select if you are using a mix of 802 11ac and 802 11n wireless clients Mixed 802 1 1ac 802 11n and 802 1 1a Select if you are using a mix of 802 11ac 802 11n and 802 1 1a wireless clients Indicates the channel setting for the DAP 1665 The channel can be changed to fit the channel setting for an existing wireless network or to reduce interference in congested areas If you enable Auto Channel Scan this option will not be av
23. the IPv6 Internet My IPv6 Connection is Static IPv6 LAN IPV6 ADDRESS SETTINGS Enter the information provided by your Internet Service Provider ISP LAN IPv6 Address Subnet Prefix Length Default Gateway Primary DNS Server Secondary DNS Server 47 Section 3 Configuration My IPv6 Connection is IPv6 DNS Settings Primary DNS Server Secondary DNS Server Select Autoconfiguration SLAAC DHCPv6 from the drop down menu The access point will request IPv6 settings from a DHCPV6 server on your network You can select to have the access point automatically obtain DNS server settings from the DHCP server or you can specify IPv6 DNS server settings to be used If you select Obtain IPv6 DNS automatically no further configuration is required Enter the primary IPv6 DNS server address to be used Enter the secondary IPv6 DNS server address to be used Click Save Settings at the top of the page to save the current configuration D Link DAP 1665 User Manual IPV6 CONNECTION TYPE Choose the mode to be used by the AP to connect to the IPv6 Internet My IPv6 Connection is Autoconfiguration SLAAC DHCPv6 IPV6 DNS SETTINGS Obtain DNS server address automaticaly or enter a specific DNS server address O Obtain IPv6 DNS Server automatically Use the following IPv6 DNS Servers Primary DNS Server Secondary DNS Server 48 Section 3 Configuration Advanced
24. the wireless router D Link DAP 1665 User Manual Wireless Network Connection The network test requires a network key also called a WEP key or WPA key A network key helps prevent unknown intruders from connecting to this network Type the key and then cick Connect Network key mie a ere be Onin ECG He hee Connect Cancel 85 Section 6 Troubleshooting Troubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the DAP 1665 Read the following descriptions if you are having problems 1 Why can t I access the web based configuration utility When entering the name or IP address of the D Link access point 192 168 0 50 for example you are not connecting to a website on the Internet or have to be connected to the Internet The device has the utility built in to a ROM chip in the device itself Your computer must be on the same IP subnet to connect to the web based utility e Make sure you have an updated Java enabled web browser We recommend the following e Microsoft Internet Explorer 7 0 or higher e Mozilla Firefox 12 0 or higher e Google Chrome 20 0 or higher e Apple Safari 4 0 or higher e Verify physical connectivity by checking for solid link lights on the device If you do not get a solid link light try using a different cable If the computer is turned off the link light may not be on e Disable any Internet security softwa
25. using both 802 11n and non 802 11n wireless devices 20 MHz Select if you are not using any 802 1 1n wireless clients Select whether you would like the network name SSID of your wireless network to be Visible or Invisible to wireless clients If Invisible the SSID of the DAP 1665 will not be seen by site survey utilities so wireless clients will have to manually enter the SSID of your wireless network in order to connect to it Click Save Settings at the top of the page to save the current configuration D Link DAP 1665 User Manual GHZ WIRELESS NETWORK SETTINGS Enable Wireless Always Wireless Network Name Abo called the SSID 802 11 Mode Mixed 802 11ac 802 11n and 802 113 Wireless Channel 35 Enable Auto Channel Scan Channel Width Auto 20 40 80MHz Visibility Status Visible Invisible GHZ WIRELESS SECURITY SETTING Security Mode None 30 Section 3 Configuration Wireless Mode Site Survey Wireless Network Name 802 11 Band Channel Width Security Mode Wireless MAC Clone Wi Fi Protected Setup Current PIN Wireless Client Mode Select Wireless Client Mode from the drop down menu Click Site Survey to display a list of wireless networks in your area To select a wireless network click the radio button in the far right column of the scan page Click Connect at the bottom of the scan page to confirm the selection The wireless network name will autom
26. 02 11 Mode Mixed 802 11ac 802 iin and 802 113 Wireless Channel Enable Auto Channel Scan Channel Width Auto 20 40 80MHz 5GHZ WIRELESS SECURITY SETTING 29 Section 3 Configuration 802 11 Mode Wireless Channel Enable Auto Channel Scan Channel Width Visibility Status Select one of the following 802 11a Only Select if you are only using 802 11a wireless clients 802 11n Only Select if you are only using 802 11n wireless clients Mixed 802 11n and 802 11a Select if you are using a mix of 802 11n and 802 11a wireless clients 802 11ac Only Select if you are only using 802 11ac wireless clients Mixed 802 1 1ac and 802 1 1n Select if you are using a mix of 802 11ac and 802 11n wireless clients Mixed 802 1 1ac 802 11n and 802 1 1a Select if you are using a mix of 802 11ac 802 11n and 802 1 1a wireless clients Indicates the channel setting for the DAP 1665 The channel can be changed to fit the channel setting for an existing wireless network or to reduce interference in congested areas If you enable Auto Channel Scan this option will not be available The Auto Channel Scan setting can be selected to allow the DAP 1665 to automatically choose the channel with the least amount of interference Select the Channel Width Auto 20 40 80 Select this option if you are using a combination of 802 11ac 802 11n and other wireless devices Auto 20 40 Select if you are
27. Bridge with AP mode page 13 D Link DAP 1665 User Manual 8 Section 2 Installation Access Point Mode Access Point AP mode adds wireless capability to your existing wired network The DAP 1665 acts as a central connection point for any computer client that has an 802 11ac or backwards compatible 802 1 1n g b a wireless network interface and is within range of the access point Clients must connect to the network name SSID broadcast by the access point in order to wirelessly access the network If wireless security is enabled on the access point the client will need to enter a password to connect In Access Point mode multiple clients can connect wirelessly to the network at the same time AP Mode Internet Router DAP 1665 Wireless Devices D Link DAP 1665 User Manual 9 Section 2 Installation Wireless Client Mode In Wireless Client mode the DAP 1665 acts as a wireless network adapter for your Ethernet enabled device such as a game console or a TV set top box Connect your Ethernet enabled device to the access point using an Ethernet cable and enjoy wired speeds of up to 1000 Mbps If you are going to connect several Ethernet enabled devices to your DAP 1665 connect the LAN port of the DAP 1665 to an Ethernet switch then connect your devices to this switch Example Connect a gaming console using an Ethernet cable to the DAP 1665 The unit is set to Wireless Client mode which will wirelessly connect to a wireless
28. D D ink Version 1 01 28 08 2014 User Manual DAP 1665 Wireless AC1200 Dual Band Access Point DAP 1665 Preface D Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes Manual Revisions fete ne CO 1 01 August 28 2014 e Initial release Trademarks D Link and the D Link logo are trademarks or registered trademarks of D Link Corporation or its subsidiaries in the United States or other countries All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies Apple Apple logo Safari iPhone iPad iPod touch and Macintosh are trademarks of Apple Inc registered in the U S and other countries App Store is a service mark of Apple Inc Chrome browser Google Play and Android are trademarks of Google Inc Internet Explorer Windows and the Windows logo are trademarks of the Microsoft group of companies Copyright 2014 by D Link Corporation Inc All rights reserved This publication may not be reproduced in whole or in part without prior expressed written permission from D Link Corporation Inc The purpose of this product is to create a constant network connection for your devices As such it does not have a standby mode or use a power management mode If you wish to power down this product please s
29. GHZ WIRELESS SECURITY SETTING Security Mode WE WEP Encryption 6 it 10 hex digits WEP Key 1 Authentication Both 42 Section 3 Configuration Security Mode WPA Mode Cipher Type Pre Shared Key WPA Enterprise uses a RADIUS authentication server to provide centralized authentication for wireless access If you are missing any of the information WPA Personal Select WPA Personal from the drop down menu There are two versions of WPA supported by the DAP 1665 WPA and WPA2 It is recommended that you use Auto WPA or WPA2 so that the WPA2 version will be used if connecting wireless clients support it Choose a cipher type from the drop down menu Enter the desired pre shared key password for the wireless network Wireless clients will need this key in order to connect to your wireless network Click Save Settings at the top of the page to save the current configuration 2 4GHZ WIRELESS SECURITY SETTING Security Mode WPA Mode Cipher Type Pre Shared Key AES password WPA Enterprise required for this setup please contact your network administrator Security Mode WPA Mode Cipher Type RADIUS Server IP Address Pre Shared Key Radius Server Shared Secret Select WPA Enterprise from the drop down menu There are two versions of WPA supported by the DAP 1665 WPA and WPA2 It is recommended that you use Auto WPA or WPA2 so that the WPA2 version will be used if connec
30. HCP server always broadcast its response to clients This can help to avoid problems when clients fail to obtain an IP address from the DHCP server The gateway address which will be sent to requesting clients Enter the WINS server address which will be sent to requesting clients Enter the DNS server address which will be sent to requesting clients Select the desired DHCP address lease length time from the drop down menu This table will show details of clients which are currently receiving a DHCP address from the DHCP server Click Save Settings at the top of the page to save the current configuration D Link DAP 1665 User Manual DHCP SERVER SETTINGS Use this section to configure the built in DHCP Server to assign IP addresses to the computers on your network Enable DHCP Server 192 168 0 100 fo 192 166 0 200 addresses within the LAN subnet 192 168 0 50 DHCP IP Address Range Gateway WINS 192 168 0 50 DNS 192 168 0 50 DHCP Lease Time 1lHour DYNAMIC DHCP CLIENT LIST 46 Section 3 Configuration IPv6 The DAP 1665 can be configured to operate using the IPv6 protocol If you are connecting the access point to a network which is using IPv6 you should adjust the appropriate settings in this section My IPv6 Connection is LAN IPv6 Link Local Address My IPv6 Connection is LAN IPv6 Address Subnet Prefix Length Default Gateway Primary DNS Server Seco
31. Password ADMINISTRATION Enable Graphical E Enable Check the box to enable graphical authentication Graphical Authentication Graphical authentication uses a challenge response test to prevent Authentication unauthorized users from gaining access to the configuration utility through automated means Click Save Settings at the top of the page to save the current configuration D Link DAP 1665 User Manual 61 Section 3 Configuration System The System page can be used to save and restore the device s configuration as well as restore the factory default settings Save Settings to Click Save to save the access point s current configuration to SR Local Hard Drive a file on your local computer After clicking a Save File dialog will appear prompting you to save the configuration file on Save Settings To Local Hard Drive your computer Load Settings From Local Hard Drive Upload Settings _ Load Settings Click Browse to locate a previously saved configuration file Restore To Factory Default From Local Hard on your local computer Once the file has been located click a Drive Upload Settings to apply the configuration in the file to the Reboot The Device access point Note This will overwrite any current configuration Restore to Click Restore Device to reset the DAP 1665 settings to the Factory Default factory defaults Settings Warning This will erase all current settings and cannot be undone Reboot the Click
32. Reboot to reboot the device You will need to log in to the Device device again once the reboot has been completed D Link DAP 1665 User Manual 62 Section 3 Configuration Firmware Information Check the Latest Firmware and Language Pack Versions Firmware Upgrade Language Pack Upgrade Firmware Use the Firmware page to update the device s firmware and add or remove language packs This section displays information about the device s current firmware and language pack Click Remove to remove any currently installed language packs Click Check Now to check for new firmware or language pack versions Note The access point must have an active Internet connected to check for firmware and language pack updates If the above check for firmware and language packs detected updates the details will displayed here Click Download to download the update files to your computer Click Browse to locate a firmware file on your computer Once located click Upload to commence the firmware upgrade process It is recommended that you save your current router configuration using the System page before you begin a firmware upgrade Warning You must use a wired connection to the access point to update the firmware Click Browse to locate a language pack file on your computer Once located click Upload to commence the language pack upgrade process D Link DAP 1665 User Manual FIRMWARE INFORMATION Current Firmware Ver
33. SID of your Channel Width Auto 20 40 80MHz wireless network in order to connect to it Visibility Status Visible Invisible Security Forinformation on how to set up wireless security please refer TAN CRE art Mode to Configuring Wireless Security on page 42 WPA Personal AUTO WPA or WPA2 Click Save Settings at the top of the page to save the current i configuration password Note If the repeater network uses the 5 GHz band the Wireless Channel Auto Channel Scan and Visibility Status options will not be available for configuration The DAP 1665 will use the settings of the repeater network for these options D Link DAP 1665 User Manual 40 Section 3 Configuration Using WPS Enable Check the box to enable wireless devices to connect to the access point using WPS Current PIN Displays the current PIN to be used by clients connecting using the WPS PIN method Reset PIN to Click to reset the access point s WPS PIN to the factory default Default Generate Click to generate a new WPS PIN New PIN Process WPS Click to commence the WPS PBC Push Button setup process D Link DAP 1665 User Manual WIFI PROTECTED SETUP ALSO CALLED WCN 2 0 IN WINDOWS VISTA Enable Current PIN 26018539 Reset PIN to Default Generate New PIN 41 Section 3 Configuration Configuring Wireless Security Wireless security encryption prevents unauthorized users from accessing your wir
34. Select one of the following 802 11n Only Select if you are only using 802 11n wireless clients Mixed 802 11n and 802 119 Select if you are using a mix of 802 11n and 802 11g wireless clients Mixed 802 11n 802 11g and 802 11b Select if you are using a mix of 802 11n 802 119 and 802 11b wireless clients Indicates the channel setting for the DAP 1665 The Channel can be changed to fit the channel setting for an existing wireless network or to reduce interference in congested areas If you enable Auto Channel Scan this option will not be available The Auto Channel Scan setting can be selected to allow the DAP 1665 to automatically choose the channel with the least amount of interference Select the Channel Width Auto 20 40 Select if you are using both 802 11n and non 802 11n wireless devices 20 MHz Select if you are not using any 802 1 1n wireless clients D Link DAP 1665 User Manual WIRELESS MODE Wireless Mode AccessPoint 2 4GHZ WIRELESS NETWORK SETTINGS Enable Wireless Always Wireless Network Name dlink 96C1 Also called the SSID 802 11 Mode Mixed 802 11n 802 11g and 802 11b Wireless Channel Enable Auto Channel Scan Channel Width Auto 20 40MHz Visible Invisible 2 4GHZ WIRELESS SECURITY SETTING 28 Section 3 Configuration Visibility Status Security Mode Enable Wireless Wireless Network Name Select whether you would like the network name
35. Status Device Info This page displays the current information for the DAP 1665 such as LAN and wireless LAN information and statistics General LAN Wireless LAN Wireless LAN 2 Displays the access point s time and firmware version Displays the MAC address and the private local IP settings for the access point Displays the wireless MAC address and wireless settings such as SSID and channel for the 2 4 GHz wireless band Displays the wireless MAC address and wireless settings such as SSID and channel for the 5 GHz wireless band D Link DAP 1665 User Manual GENERAL MAC Address Connection IP Address Subnet Mask Default Gateway WIRELESS LAN MAC Address Network Name SSID Channel Width Channel Security Mode Wi H Protected Setup WIRELESS LAN 2 7 15 2013 23 54 15 1 00 Mon 15 Jul 2013 00 e0 4c 91 96 c1 Dynamic IP 192 168 0 101 255 255 255 0 192 168 0 2 O0 E0 4C 81 96 D1 dlink 96C1 40MHz 2 Open Disabled Enable Configured O0 E0 4C 81 96 C1 dlink 96C1 5GHz BOMHZ 149 Open Disabled Disable Configured 67 Section 3 Configuration Logs TheDAP 1665 keeps a running log of events and activities occurring on the access point If the device is rebooted the logs will automatically be cleared Log Options There are several types of logs that can be viewed System Activity Debug Information Attacks Dropped Packets and Not
36. This section allows you to configure the advanced parameters of your DAP 1665 There will be different advanced features available for configuration based on the mode in which your device is operating The instructions below are listed according to operation mode Access Point Mode Access Control Mac filtering allows you to control wireless access to your network according to clients MAC addresses Configure MAC Filtering Checkbox MAC Address Use the drop down menu to select your desired MAC filtering method Turn MAC Filtering OFF No MAC filtering will be implemented Turn MAC Filtering ON and ALLOW MAC filtering will be turned on and only MAC addresses listed in the table below will be allowed access Turn MAC Filtering ON and DENY MAC filtering will be turned on and only MAC addresses listed in the table below will be denied access Check the box to include this MAC address in the MAC filtering rules Enter the MAC address of the client that you wish to filter If the client is currently connected to the access point you can select it from the Client List drop down menu and click lt lt to automatically populate the field Click Clear to clear all fields Click Save Settings at the top of the page to save the current configuration D Link DAP 1665 User Manual ACCESS CONTROL SETTINGS Configure MAC Filtering below Turn MAC Filtering OFF MAC Address Client List 49 Section 3 Configur
37. ailable The Auto Channel Scan setting can be selected to allow the DAP 1665 to automatically choose the channel with the least amount of interference D Link DAP 1665 User Manual GHZ WIRELESS NETWORK SETTINGS Add New gt Always dlink 07DA O Same as Repeater Name Create a New Wi Fi Network Name Also called the SSID 802 11 Mode Wireless Channel 35 Enable Auto Channel Scan Channel Width Auto 20 40 80MHz Visibility Status Visible Invisible Mixed 802 ilac 802 11n and 802 113 DGHZ WIRELESS SECURITY SETTING WPA Personal AUTO WPA or WPAZ AES F password 39 Section 3 Configuration Channel Select the Channel Width 5GHZ WIRELESS NETWORK SETTINGS Width Auto 20 40 80 MHz Select this option if you are using a combination of 802 11ac 802 11n and other wireless devices i Always mickihicn Auto 20 40 MHz Select if you are using both 802 11n and er non 802 11n wireless devices Same as Repeater Name 20 MHz Select if you are not using any 802 1 1n wireless clients eee RER Re Also called the SSID Visibility Select whether you want the wireless network name SSID of 802 11 Mode Mixed 802 11ac 802 1in and 802 11a Status the 2 4 GHz band to be Visible or Invisible If Invisible the Wireless Channel SSID of the DAP 1665 will not be seen by site survey utilities Enable Auto Channel Scan so wireless clients will have to manually enter the S
38. atically appear in the Wireless Network Name field below Enter the SSID of the wireless network that you wish to connect to If you do not know for sure click Site Survey and select it from the list if available Select the wireless band of the wireless network that you wish to connect to You can only be connected to one wireless band at any one time Select the channel width that you wish to use when connecting to the wireless network Select the wireless security mode and relevant settings used by the network you are connecting to For more information regarding wireless security please refer to Configuring Wireless Security on page 42 Check Enable to clone the MAC address of another device Choose Auto or Manual cloning and enter the MAC Address or click Scan to search for MAC addresses of connected devices Check Enable if you wish to enable the use of the PIN method for Wi Fi Protected Setup WPS Displays the current PIN which can be used to connect to the router using the WPS PIN method Click Reset PIN to Default to reset the PIN number to the factory default setting Click Generate New PIN to randomly generate a new PIN for WPS connection Click Process WPS to commence the WPS Push Button setup process Click Save Settings to save the current configuration D Link DAP 1665 User Manual WIRELESS MODE Wireless Client Site Survey 2 4GHZ WIRELESS NETWORK SETTINGS Wireless Network Name d ink
39. ation On this page you can adjust the advanced wireless settings for both the 2 4 GHz band and the 5 GHz band Transmit Power WMM Enable Short GI IGMP Snooping WLAN Partition HT 20 40 Coexistance Advanced Wireless 2 4 GHz Band Select the desired transmission power of the wireless radio from the drop down menu Wireless Multimedia WMM is a QoS engine which can help to reduce lag and latency when transmitting multimedia over your wireless connection This is permanently enabled Enabling a short Guard Interval GI can increase throughput However it can also increase error rate in some installations due to increased sensitivity to radio frequency reflections Select the option that works best for your installation Enabling this option allows the access point to listen for Internet Group Management Protocol IGMP traffic which can help to detect clients which require multicast streams Enabling this option means that connection wireless clients will not be able to communicate with one another but will still have access to network resources such as the Internet Enable this option to reduce interference from other wireless networks in your area If the channel width is operating at 40 MHz and there is another wireless network s channel over lapping and causing interference the router will automatically change to 20 MHz Click Save Settings at the top of the page to save the current configuration
40. ave the same name SSID as the repeater network Create a New Wi Fi Network Name Enter a new name SSID for the extended network in the field below D Link DAP 1665 User Manual WIRELESS MODE Repeater WIRELESS SETTING Repeater Network Name diink O7DA Also called the SSID Repeater Network Band 3 4GHz 5GHz Channel Width Auto 20 40MHz 2 4GHZ WIRELESS NETWORK SETTINGS Always dlink 07DA Add New Same as Repeater Name Create a New Wi Fi Network Name Also called the SSID 802 11 Mode Mixed 802 11n 802 119 and 802 11b Channel Width Auto 20 40MHz 2 4GHZ WIRELESS SECURITY SETTING WPA Personal AUTO WPAor WPA2 AES password r 37 Section 3 Configuration ro Select one et the ee l _ 2 4GHZ WIRELESS NETWORK SETTINGS Mode trees a Only Select if you are only using 802 11n wireless Poe anes Mixed 802 11n and 802 11g Select if you are using a mix of ee n 802 11n and 802 11g wireless clients Local WiFi Network Name Same as Repeater Name Mixed 802 11n 802 11g and 802 11b Select if you are using Create a New Wi Fi Network Name a mix of 802 11n 802 11g and 802 11b wireless clients Also called the SSID 802 11 Mode Mixed 802 11n 802 11gand802 1ib Wireless Indicates the channel setting for the DAP 1665 The channel Channel Width Auto 20 40MHz Channel canbechanged to fit the channel setting for an existing
41. d but set Packet needs to fragmented but set Packet needs to be fragmented but set Ping statistics for 66 94 234 13 MI Ee _ Packets Sent 4 Received B 4 ee oa loss Example ping yahoo com f 1472 Approximate round trip times in milli seconds Minimum Bms Maximum Bms Average Pms C vping yahoo com F 1 1472 Pinging yahoo com 66 94 234 131 with 1472 bytes of data Reply from 66 94 234 13 bhytes 1472 time 93ms TTL 52 Reply from 66 94 234 13 bytes 1472 time 19ms TTL 52 Reply from 66 94 234 13 bytes 1472 time 125ms TTL 52 Reply from 66 94 234 13 bytes 1472 time 203ms TTL 52 Ping statistics for 66 94 234 13 Packets Sent 4 Received 4 Lost B Bz loss Approximate round trip times in milli seconds Minimum 93ms Maximum 203ms Average Cos D Link DAP 1665 User Manual 88 Section 6 Troubleshooting You should start at 1472 and work your way down by 10 each time Once you get a reply go up by 2 until you get a fragmented packet Take that value and add 28 to the value to account for the various TCP IP headers For example lets say that 1452 was the proper value the actual MTU size would be 1480 which is the optimum for the network we re working with 14524 28 1480 Once you find your MTU you can now configure your access point with the proper MTU size To change the MTU rate on your access point follow the steps below e Open your browser enter the IP address of your access po
42. devices A wall that is 1 5 feet thick 5 meters at a 45 degree angle appears to be almost 3 feet 1 meter thick At a 2 degree angle it appears over 42 feet 14 meters thick Position devices so that the signal will travel straight through a wall or ceiling instead of at an angle for better reception 3 Building materials make a difference A solid metal door or aluminum studs may have a negative effect on range Try to position access points wireless routers and computers so that the signal passes through drywall or open doorways Materials and objects such as glass steel metal walls with insulation water fish tanks mirrors file cabinets brick and concrete will degrade your wireless signal 4 Keep your product away at least 3 6 feet or 1 2 meters from electrical devices or appliances that generate RF noise 5 If you are using 2 4 GHz cordless phones or X 10 wireless products such as ceiling fans lights and home security systems your wireless connection may also be affected Make sure your 2 4 GHz phone base is as far away from your wireless devices as possible The base transmits a signal even if the phone is not in use D Link DAP 1665 User Manual 14 Section 3 Configuration Configuration This section will show you how to configure your D Link wireless access point using the web based configuration utility Web based Configuration Utility If you wish to change the default settings or adjust the configura
43. e mode but adds the functionality of Access Point mode meaning that wireless clients can connect to one of the DAP 1665s and have access to both networks via the wireless bridge Note The Bridge with AP mode is not specified in the Wi Fi or IEEE standards This mode will only work using two DAP 1665 units Compatibility with other APs even other D Link APs is not guaranteed Bridge with AP Mode i i i i Internet Router DAP 1665 DAP 1665 Router Switch Switch Les Les el Wireless Devices Wireless Devices D Link DAP 1665 User Manual 13 Section 2 Installation Wireless Installation Considerations The DAP 1665 wireless access point lets you access your network using a wireless connection from virtually anywhere within the operating range of the device Keep in mind however that the number thickness and location of walls ceilings or other objects that the wireless signals must pass through may limit the range Typical ranges vary depending on the types of materials and background RF radio frequency noise in your home or business The key to maximizing wireless range is to follow these basic guidelines 1 Keep the number of walls and ceilings between the D Link access point and other network devices to a minimum Each wall or ceiling can reduce your adapter s range from 3 90 feet 1 30 meters Position your devices so that the number of walls or ceilings is minimized 2 Be aware of the direct line between network
44. e network security key Y You can also connect 4 by pushing the button on the router Cancel Networks Airplane mode Off Wi Fi d link 07725 Connected ll 75 Section 5 Connecting to a Wireless Network Windows 7 It is recommended to enable wireless security WPA WPA2 on your wireless router or access point before configuring your wireless adapter If you are joining an existing network you will need to know the security key or passphrase being used 1 Click on the wireless icon in your system tray lower right corner 11 41 AM i B he Bi L t O 7 2009 Wireless Icon 2 The utility will display any available wireless networks in your area Not connected oil Connections are available Wireless Network Connection dlink kay2690_24 AllenH DIR 655 SD6_WLAN DAP 2690g wpstestl BBIQ6ss304 WPA Eddie APNAS Open Network and Sharing Center D Link DAP 1665 User Manual 76 Section 5 Connecting to a Wireless Network 3 Highlight the wireless network SSID you would like to connect to and click the Connect button If you get a good signal but cannot access the Internet check your TCP IP settings for your wireless adapter Refer to the Networking Basics section in this manual for more information 4 The following window appears while your computer tries to connect to the router D Link DAP 1665 User Manual Mot connected dll Connections are available Wire
45. eless network The DAP 1665 features two methods of wireless security encryption Wired Equivalent Privacy WEP and Wi Fi Protected Access WPA It is recommended that you use WPA security if your wireless devices support this standard as it is more secure than the older WEP standard For more details of wireless security standards please refer to Wireless Security on page 72 Note Unless otherwise specified the security configuration process is the same for both the 2 4 GHz and 5 GHz bands Security Mode WEP Encryption WEP Key 1 Authentication WEP Select WEP from the drop down menu The WEP standard offers two levels of encryption 64 bit and 128 bit Each level has the option of a key password consisting of either HEX digits or ASCII characters 64Bit 10 hex digits Uses a key consisting of 10 hex digits 0 9 A F 64Bit 5 ascii characters Uses a key consisting of 5 ASCII characters 0 9 A Z plus symbols 128Bit 26 hex digits Uses a key consisting of 26 hex digits 0 9 A F 128bit 13 ascii characters Uses a key consisting of 13 ASCII characters 0 9 A Z plus symbols Enter the desired WEP key password for your wireless network The key should adhere to the requirements of WEP Encryption method specified above Select an authentication method from the drop down menu Click Save Settings at the top of the page to save the current configuration D Link DAP 1665 User Manual 2 4
46. f being conveniently set up by using the PIN or Push Button methods 1 Maximum wireless signal rate derived from draft 802 1 1ac specifications Actual data throughput will vary Network conditions and environmental factors including volume of network traffic building materials and construction and network overhead lower actual data throughput rate Environmental factors will adversely affect wireless signal range Wireless range and speed rates are D Link RELATIVE performance measurements based on the wireless range and speed rates of a standard Wireless N product from D Link D Link DAP 1665 User Manual 3 Section 1 Product Overview Features Faster Wireless Networking The DAP 1665 provides combined wireless speeds of up to 1200 Mbps This capability allows users to participate in real time activities online such as video streaming online gaming and real time audio Flexible Operation Modes The DAP 1665 can operate as an Access Point Repeater Wireless Client Bridge and Bridge with AP meaning that you can customize its operation to suit your specific networking requirements Gigabit Ethernet Port The built in Gigabit Ethernet port facilitates a wired connection of upto 1 Gbps meaning that wired devices can also take advantage of the DAP 1665 s high speed wireless capabilities Compatible with IEEE 802 11n g b a Devices The DAP 1665 is still fully compatible with the 802 1 1n g b a standards so it can connect with existi
47. forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body NOTE IMPORTANTE D claration d exposition aux radiations Cet quipement est conforme aux limites d exposition aux rayonnements IC tablies pour un environnement non contr l Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps This radio transmitter identify the device by certification number or model number if Category II has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated Antenna types not included in this list having a gain greater than the maximum gain indicated for that type are strictly prohibited for use with this device Le pr sent metteur radio IC 4216A AP1665A1 a t approuv par Industrie Canada pour fonctionner avec les types d antenne num r s ci dessous et ayant un gain admissible maximal et l imp dance requise pour chaque type d antenne Les types d antenne non inclus dans cette liste ou dont le gain est sup rieur au gain maximal indiqu sont strictement interdits pour l exploitation de l metteur TELEC Statement Eric RUSGHZ Ic BA AICIRUES D Link DAP 1665 User Manual 95
48. g from the drop Offset down menu Daylight Saving Dates HST start Mar 3d Sun 2am DST End Nov 3nd Sun 2 am Daylight Saving Use the drop down menus to set the Start and End dates for Dates daylight saving time AUTOMATIC TIME CONFIGURATION Enable NTP Check the box to have the access point automatically Server synchronize its clock and calendar with an online NTP server NTP Server Used Type the address of the NTP server you would like to use in the seen field provided or choose a pre determined server from the nate and time Ye 215 v Month M gt Day 16 1 2 IME drop down menu and click lt lt to populate the field agli SR acu an Copy Your Computer s Time Settings Date and Time Use the drop down menus to manually configure the time and date This option will not be available if Enable NTP Server is selected above Click Save Settings at the top of the page to save the current configuration D Link DAP 1665 User Manual 64 Section 3 Configuration System Check Host Name or IP Enter the host name or IP address for which you wish to conduct Address a ping test Ping Result Displays results of the ping test above D Link DAP 1665 User Manual PING TEST Host Name or IP address PING RESULT Enter a host name or IP address above and click Ping 65 Section 3 Configuration Name Day s All Day 24 hrs Time format Start Time End Ti
49. he equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help D Link DAP 1665 User Manual 93 Appendix C Compliance Statements FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment Operations in the 5 15 5 25GHz band are restricted to indoor usage only This transmitter must not be co located or operating in conjunction with any other antenna or transmitter IMPORTANT NOTE FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body Note The country code selection is for non US model only and is not available to all US model Per FCC regulation all WiFi product marketed in US must fixed to US operation channels only Industry Canada Statement This device complies with Industry Canada licence exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Le pr sent appareil est conforme aux CNR d Industrie Canada applicables
50. ice Check the boxes to display log items of each type Click Apply Log Settings Now to update the log options LOG OPTIONS System Activity V System Activity Debug Information Attacks Dropped Packets Notice First Page This button directs you to the first page of the log Last Page This button directs you to the last page of the log _First Page Previous Page Previous Page This button directs you to the previ f the sale revious Page This button directs you to the previous page of the log Jul 15 23 52 46 rtl8192cd_dfs_det_chk_timer 722 DFS detected Next Page This button directs you to the next page of the log Clear Log This button clears all current log content Save Log This button allows you to save the current log to a file on your local computer Refresh This button refreshes the log D Link DAP 1665 User Manual 68 Section 3 Configuration Statistics The DAP 1665 keeps statistics of the traffic that passes through it You can view the amount of packets that pass through the LAN and wireless portions of the network The traffic counter will reset if the access point is rebooted Use the buttons at the top of the page to Refresh or Clear the statistics Traffic Statistics display Receive and Transmit packets passing through the DAP 1665 Refresh Statistics Clear Statistics LAN STATISTICS D Link DAP 1665 User Manual 69 Section 3 Configuration Wireless The wireless section a
51. illa Firefox 12 0 or higher e Google Chrome 20 0 or higher e Apple Safari 4 0 or higher Windows Users Make sure you have the latest version of Java installed Visit www java com to download the latest version D Link DAP 1665 User Manual Section 1 Product Overview Introduction D Link an industry leader in networking introduces the new D Link DAP 1665 Wireless AC1200 Dual Band Access Point With the ability to transfer files with a maximum combined wireless signal rate of up to 1200 Mbps the DAP 1665 gives you high speed wireless network access for your home or office The DAP 1665 is compliant with the latest draft IEEE 802 11ac standard meaning that it can connect and inter operate with other 802 1 1ac compatible wireless client devices The DAP 1665 is also backwards compatible with 802 1 1b g n devices It can be flexibly configured to operate in 5 different modes Access Point Wireless Client Bridge Bridge with AP and Repeater With its setup wizard the DAP 1665 ensures that you will be up and running on a wireless network in just a matter of minutes The DAP 1665 features Wi Fi Protected Access WPA PSK WPA2 PSK to provide an enhanced level of security for wireless data communications The DAP 1665 also includes additional security features to keep your wireless connection safe from unauthorized access The DAP 1665 also supports Wi Fi Protected Setup WPS repeater and wireless client operation modes each capable o
52. iltering ON and DENY MAC filtering will be turned on and only MAC addresses listed in the table below will be denied access Check the box to include this MAC address in the MAC filtering rules Enter the MAC address of the client that you wish to filter If the client is currently connected to the access point you can select it from the Client List drop down menu and click lt lt to automatically populate the field Click Clear to clear all fields Click Save Settings at the top of the page to save the current configuration D Link DAP 1665 User Manual ACCESS CONTROL SETTINGS Configure MAC Filtering below Turn MAC Filtering OFF r MAC Address Client List 57 Section 3 Configuration Advanced Wireless On this page you can adjust the advanced wireless settings Transmit Power WMM Enable Short GI IGMP Snooping WLAN Partition HT 20 40 Coexistance Select the desired transmission power of the wireless radio from the drop down menu Wireless Multimedia WMM is a QoS engine which can help to reduce lag and latency when transmitting multimedia over your wireless connection This is permanently enabled Enabling a short Guard Interval GI can increase throughput However it can also increase error rate in some installations due to increased sensitivity to radio frequency reflections Select the option that works best for your installation Enabling this option allows the access point to
53. imply unplug it from the power outlet Power Usage This device is an Energy Related Product ErP with High Network Availability HINA and automatically switches to a power saving Network Standby mode within 1 minute of no packets being transmitted It can also be turned off through a power switch to save energy when it is not needed Network Standby 4 31 watts Switched Off 0 11 watts D Link DAP 1665 User Manual i Table of Contents Table of Contents Prea LORS ee Access Point Mode nn 17 MANU TIRE ICS a nn i Wireless Client Mode ns 19 Trademarks mes i Repeater Mode nn 23 FOWOF US ANG a ee Manual COMITE csesetesecsecs aca cence capseen eccverceseceenacceec 27 Wireless SettingS stesssncncustscsccgsevsssasessssassnansacorarsteensennsistnssenn 27 Product Overview sscecseccesecccsccccscecsccesscecsccesscecsecesscecscee 1 OANE EST E cece eects cee cs 28 Package Contents RS noses 1 AE Cd ecco 31 System BAU ENEAS A E E E 2 Bridge MOE nn 32 HT FOOUCTION ee oni E E E 3 Bridge with AP Mode sesssssssssusssessuseisunenn 33 Features HR Se 4 Repeater MOE cree 37 Hardware CMERMIEN PIEEO PEE ne 5 Configuring Wireless Security nn 42 CMI TUINS Siaa 2 LAN SC UND a me ie 45 earner teen Peete ence i EELE E E PEA A E A E TA 49 WPS BUUON im 7 EOE EES E P 49 Installation sccccccsscsssssssscssscsscsscsscsscsscsessessessessessecsesees 8 ACCESS C ONT 0 Pere ere ree 49 Operation MOdeS cseccccssssccssssccssscecssscsc
54. ing 802 11ac 802 11n or 802 11a Select the appropriate 802 11 mode depending on which 802 11 standard you want the bridge to use Select the wireless channel that you want the bridge to use All APs on the bridge must be using the same wireless channel Select the appropriate channel width between 20MHz or Auto 20 40MHz from the drop down menu If you are using the 5 GHz band an additional Auto 20 40 80 option will be available Enter the MAC addresses of the APs in your network that will serve as bridges to wirelessly connect multiple networks Select the desired wireless security method from the drop down menu If you select WEP you should also select an encryption method from the subsequent drop down menu and enter the WEP key in the field provided If you select WPA you should enter a pre shared key password in the field provided Regardless of the security mode selected the settings should be the same on all access points within the bridge For further information regarding wireless security please refer to Configuring Wireless Security on page 42 Click Save Settings at the top of the page to save the current configuration WIRELESS MODE Wireless Mode BRIDGE SETTING Bridge Band 802 11 Mode Wireless Channel Channel Width Remote AP Mac Bridge Security WEP Key Pre Shared Key 8 63 char Bridge with AP 2 4GHz 5GHz Mixed 802 1 lac 802 1in and 802 1la 3
55. int 192 168 0 50 and click OK e Enter your username Admin and password blank by default Click OK to enter the web configuration page for the device e Click on Setup and then click Manual Configure e To change the MTU enter the number in the MTU field and click Save Settings to save your settings e Test your email If changing the MTU does not resolve the problem continue changing the MTU in increments of ten D Link DAP 1665 User Manual 89 Appendix A Networking Basics Networking Basics Check your IP address After you install your adapter by default the TCP IP settings should be set to obtain an IP address from a DHCP server i e wireless router automatically To verify your IP address please follow the steps below Click on Start gt Run In the run box type cmd and click OK Windows 7 Vista users type cmd in the Start Search box At the prompt type ipconfig and press Enter lt C AWINDOWS system32 cmd exe Microsoft Windows AF Version 5 1 2608 CC Copyright 1985 2881 Microsoft Corp This will display the IP address subnet mask and the default gateway of your adapter C Documents and Settings ipconfig Windows IF Configuration Ethernet adapter Local Area Connection Ifthe address is 0 0 0 0 check your adapter installation aae tlon bee RE ine Gubtix 4 alank security settings and the settings on your router Subnet Mask LL II iii 268 JEE 265 0 Default Gateway z 14 5 7 1 Some firewal
56. isconnect or connect to another network Unsecured network L tuesday Security enabled network Set up a connection or network Open Network and Sharing Center D Link DAP 1665 User Manual 80 Section 5 Connecting to a Wireless Network 3 Enter the same security key or passphrase Wi Fi password that is on your router and click Connect It may take 20 30 seconds to connect to the wireless network If the connection fails please verify that the security settings are correct The key or passphrase must be exactly the same as on the wireless router D Link DAP 1665 User Manual w Connect to a network Type the network security key or passphrase for Candy The person who setup the network can give you the key or passphrase Security key or passphrase Display characters FA If you have a USB flash drive with network settings for Candy insert it now Cons 81 Section 5 Connecting to a Wireless Network WPS WCN 2 0 The router supports Wi Fi protection referred to as WCN 2 0 in Windows Vista The following instructions for setting this up depends on whether you are using Windows Vista to configure the router or third party software When you first set up the router Wi Fi protection is disabled and unconfigured To enjoy the benefits of Wi Fi protection the router must be both enabled and configured There are three basic methods to accomplish this use Windows Vista s built in suppo
57. it on or off mi Win e Power Receptor Receptor for the supplied power adapter D Link DAP 1665 User Manual Section 1 Product Overview Hardware Overview LEDs 0000 1 Power LED A solid green light indicates a proper connection to the power supply 2 2 4 GHz Wireless A solid green light indicates that the 2 4 GHz wireless band is active 3 5 GHz Wireless A solid green light indicates that the 5 GHz wireless band is active 4 LAN LED A solid green light indicates the LAN port connection is active D Link DAP 1665 User Manual Section 1 Product Overview Hardware Overview WPS Button 1 WPS Button Press this button to use WPS to establish a secure connection with other wireless devices 2 Kensington Slot Connect a Kensington lock device to protect your access point against theft D Link DAP 1665 User Manual Section 2 Installation Installation Please configure the DAP 1665 with a computer connected directly to the device The following pages will explain the different operational modes you can use Operation Modes The DAP 1665 features a number of operation modes enabling you to customize it to your networking requirements Please refer to the following sections to determine which mode is most suitable for your network e Access Point mode page 9 e Wireless Client mode page 10 e Repeater mode page 11 e Bridge mode page 12 e
58. l software programs may block a DHCP request on newly installed adapters C Documents and Settings D Link DAP 1665 User Manual 90 Appendix A Networking Basics Statically Assign an IP address If you are not using a DHCP capable gateway router or you need to assign a static IP address please follow the steps below Step 1 Windows 7 Click on Start gt Control Panel gt Network and Internet gt Network and Sharing Center gt Change Adapter Setting Windows Vista Click on Start gt Control Panel gt Network and Internet gt Network and Sharing Center gt Manage Network Connections Windows XP Click on Start gt Control Panel gt Network Connections Windows 2000 From the desktop right click My Network Places gt Properties Step 2 Right click on the Local Area Connection which represents your network adapter and select Properties Step 3 Highlight Internet Protocol TCP IP and click Properties Step 4 Click Use the following IP address and enter an IP address that is on the same subnet Pre as your network or the LAN IP address on your router ES You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for Example If the router s LAN IP address is 192 168 0 1 make your IP address 192 168 0 X 7 where X is anumber between 2 and 99 Make sure that the number you choose is not in ee Use the following IP add
59. less Network Connection dlink Connect automatically kay2690_24 james2690g ALPHA dlink 888 SD6_WLAN DAP 2690q 77 Section 5 Connecting to a Wireless Network 5 Enter the same security key or passphrase that is on your router and click Connect You can also connect by pushing the WPS button on the router It may take 20 30 seconds to connect to the wireless network If the connection fails please verify that the security settings are correct The key or passphrase must be exactly the same as on the wireless router D Link DAP 1665 User Manual fee Connect to a Network Type the network security key Security key Hide characters You can also connect by pushing the O x button on the router Cancel 78 Section 5 Connecting to a Wireless Network Windows Vista Windows Vista users may use the built in wireless utility If you are using another company s utility please refer to the user manual of your wireless adapter for help with connecting to a wireless network Most utilities will have a site survey option similar to the Windows Vista utility as seen below If you receive the Wireless Networks Detected bubble click on the center of the bubble to access the utility Not Connected Wireless networks are available a Or Connect to a network Right click on the wireless computer icon in your system tray lower right Network and Sharing Center corner
60. llows you to view the wireless clients that are connected to your wireless access point Connection Time Displays the amount of time the wireless client has been connected to the access point MAC Address The Ethernet ID MAC address of the wireless client The Wireless Client table below displays Wireless clients connected to the AP Access Point In AP Client mode it displays the connected AP s MAC address and connected Time CONNECTED WIRELESS CLIENT LIST D Link DAP 1665 User Manual 70 Section 3 Configuration D Link DAP 1665 User Manual Help DAP 1665 ili Client SETUP ADVANCED MAINTENANCE STATUS HELP MENU Helpful Hints Click on the links for more Setup informations of each e Wizard section in the GUI e Wireless Setup LAN Setup Advanced Port Forwarding Port Filter MAC Address Filter DMZ Parental Control Advanced Wireless Advanced Network WI FI PROTECTED SETUP USER LIMIT Maintenance Device Administration Save and Restore Firmware Update WatchDog Time Schedules Status Device Info Log Statistics Wireless 71 Section 4 Security Wireless Security This section will explain the different types of security you can use to protect your wireless network from intruders Please note that some security methods may not be available for all operation modes The DAP 1665 offers the following types of security e Wired Equivalent Privacy WEP e Wi Fi Protected Setup WPS e Wi
61. lowing summary of your Wi Fi security settings for future reference Repeater Network Name DIR626L Wi Fi Password 11111111 The Setup Wizard has completed Click the Save button to save your settings and reboot the device 26 Section 3 Configuration Manual Configuration Wireless Settings You may also manually configure your DAP 1665 instead of running the setup wizard Please refer to the following pages for detailed instructions on how to manually configure the DAP 1665 for your desired operation mode Access Point mode page 28 Wireless Client mode page 31 Bridge mode page 32 Bridge with AP mode page 33 Repeater mode page 37 D Link DAP 1665 User Manual 27 Section 3 Configuration Wireless Mode Enable Wireless Wireless Network Name 802 11 Mode Wireless Channel Enable Auto Channel Scan Channel Width Access Point Mode 2 4 GHz Band Select Access Point from the drop down menu Check the box to enable the wireless function for the 2 4 GHz band If you do not want to use wireless uncheck the box to disable all wireless functions You may also set up a specific time range schedule Select a schedule from the drop down menu or click Add New to create a new schedule By default the schedule is set to Always Specify a network name SSID to identify the 2 4 GHz network This is the network name that wireless clients will search for when connecting to your wireless network
62. lows you to configure how the DAP 1665 uses Wi Fi Protected Setup WPS to create a secure wireless connection Enable Check the box to enable WPS WIFI PROTECTED SETUP ALSO CALLED WCN 2 0 IN WINDOWS VISTA Disable WPS PIN Check the box to disable WPS using the PIN method If this one Method option is selected wireless clients will only be able to use the Disable WPS PIN Method WPS PBC Push button Connection method Current PIN Displays the current PIN which can be used by wireless clients RSqiaasces to connect to the access point Click Reset PIN to Default to E return the PIN to its factory default Click Generate New PIN to randomly generate a new PIN ADD WIRELESS STATION Add Wireless Click Add Wireless Device With WPS to activate the WPS PBC Station Push button method You will then have 120 seconds to press Add Wireless Device With WPS the WPS button on the new device that you wish to connect Click Save Settings at the top of the page to save the current configuration D Link DAP 1665 User Manual 52 Section 3 Configuration User Limit Here you can set a maximum number of users that can be connected to the access point at any one time Enable User Check the box to enable the user limit function SS ie SSS Limit User Limit Enter a number of users between 1 32 User Limit 1 32 Click Save Settings at the top of the page to save the current configuration D Link DAP 1665 User Manual 53
63. me Schedule Rules List Schedules Use the Schedules page to create new schedule rules for various access point functions Schedules created here will be available for selection from schedule selection drop down menus throughout the configuration utility Enter a name to identity the new schedule rule Select All Week to make the rule active for all days of the week Select Select Day s to determine specific days on which to activate the rule Days can be selected by checking the boxes below Check the box to make the rule active all day for the days selected above Select whether you would like to use 24 hour or 12 hour time format Enter the time for the rule to become active on each of the days selected above Enter the time for the rule to become inactive on each of the days selected above Click Add to add the rule to the Schedule Rules List Click Clear to clear all fields This table displays a summary of all current schedule rules Click on the Edit icon to edit the rule or click on the Delete icon to delete the rule from the list D Link DAP 1665 User Manual ADD SCHEDULE RULE Name Day s All Week Select Day s Flsun Mon Tue Wed Thu Cfr Sat All Day 24 hrs Time format 24hour Start Time 0 0 AN hour minute End Time 0 0 AM hour minute SCHEDULE RULES LIST Name Day s Time Frame Schedule 1 Mon Wed Thu Fri 09 00 AM 05 00 AM 66 Section 3 Configuration
64. n 802 119 and 802 116 wireless clients Indicates the channel setting for the DAP 1665 The Channel can be changed to fit the channel setting for an existing wireless network or to reduce interference in congested areas If you enable Auto Channel Scan this option will not be available The Auto Channel Scan setting can be selected to allow the DAP 1665 to automatically choose the channel with the least amount of interference Select the Channel Width Auto 20 40 MHz Select if you are using both 802 11n and non 802 11n wireless devices 20 MHz Select if you are not using any 802 11n wireless clients D Link DAP 1665 User Manual 2 4GHZ WIRELESS NETWORK SETTINGS Enable Wireless Wireless Network Name 802 11 Mode Wireless Channel Enable Auto Channel Scan Channel Width Visibility Status Always dlink 07DA Also called the SSID Mixed 802 1in 802 iig and 802 11b 6 E Auto 20 40MHz Visible Invisible 2 4GHZ WIRELESS SECURITY SETTING Security Mode WPA Mode Cipher Type Pre Shared Key WPA Personal AUTO WPA or WPA2 AES password 34 Section 3 Configuration wireless network to be Visible or Invisible to wireless clients If Invisible the SSID of the DAP 1665 will not be seen by site en a ai survey utilities so wireless clients will have to manually enter eee ees eee Also called the SSID the SSID of your wireless network in order to connect to it
65. n t been tampered with WPA2 is based on 802 11i and uses Advanced Encryption Standard AES instead of TKIP e User authentication which is generally missing in WEP through the extensible authentication protocol EAP WEP regulates access to a wireless network based on a computer s hardware specific MAC address which is relatively simple to be sniffed out and stolen EAP is built on a more secure public key encryption system to ensure that only authorized network users can access the network WPA PSK WPA2 PSK uses a passphrase or key to authenticate your wireless connection The key is an alpha numeric password between 8 and 63 characters long The password can include symbols amp _ and spaces This key must be the exact same key entered on your wireless bridge or access point WPA WPA2 incorporates user authentication through the Extensible Authentication Protocol EAP EAP is built on a more secure public key encryption system to ensure that only authorized network users can access the network WPA WPA2 has two main security levels Personal and Enterprise WPA WPA2 Personal is sufficient for most home networks and uses a pre shared key as described above to authenticate users and encrypt data e WPA WPA2 Enterprise is designed for medium to large scale networking environments and uses a centralized RADIUS server for authentication Users must be registered and authorized by the RADIUS server in order to access the wireless netw
66. ncy reflections Select the option that works best for your installation Enabling this option allows the access point to listen for Internet Group Management Protocol IGMP traffic which can help to detect clients which require multicast streams Enabling this option means that connection wireless clients will not be able to communicate with one another but will still have access to network resources such as the Internet Enable this option to reduce interference from other wireless networks in your area If the channel width is operating at 40 MHz and there is another wireless network s channel over lapping and causing interference the router will automatically change to 20 MHz Click Save Settings at the top of the page to save the current configuration D Link DAP 1665 User Manual ADVANCED WIRELESS SETTINGS Transmit Power 100 WMM Enable Short GI IGMP Snooping WLAN Partition HT 20 40 Coexistence 56 Section 3 Configuration Repeater Mode Access Control Mac filtering allows you to control wireless access to your network according to clients MAC addresses Configure MAC Filtering Checkbox MAC Address Use the drop down menu to select your desired MAC filtering method Turn MAC Filtering OFF No MAC filtering will be implemented Turn MAC Filtering ON and ALLOW MAC filtering will be turned on and only MAC addresses listed in the table below will be allowed access Turn MAC F
67. ndary DNS Server Select Link Local Only from the drop down menu This will set the access point s local IPV6 address The router s local IPv6 address will be displayed here This address should be used to access the web based configuration utility through the IPv6 protocol Click Save Settings at the top of the page to save the current configuration Select Static IPv6 from the drop down menu This will allow you to assign a static IPv6 address to the access point The router s local IPv6 address will be displayed here This address should be used to access the web based configuration utility through the IPv6 protocol Enter the prefix length for IPv6 IP addresses on your network Enter the default IPv6 gateway address for your network Enter the primary IPv6 DNS server address for your network Enter the secondary IPV6 DNS server address for your network Click Save Settings at the top of the page to save the current configuration D Link DAP 1665 User Manual IPV6 CONNECTION TYPE Choose the mode to be used by the AP to connect to the IPv6 Internet My IPv6 Connection is Link Local Only LAN IPV6 ADDRESS SETTINGS Use this section to configure the internal network settings of your router The LAN IPv6 Link Local Address is the IPv6 Address that you use to access the Web based management interface LAN IPv6 Link Local Address IPV6 CONNECTION TYPE Choose the mode to be used by the AP to connect to
68. ng wireless adapters found on older devices e Robust Security Use WPS Wi Fi Protected Setup to create a secure connection to new devices in a matter of seconds by simply pushing a button or entering a PIN There s also WPA WPA2 security encryption allowing you to customize your network s security e User friendly Setup Wizard Through its easy to use web based user interface the DAP 1665 lets you control what information is accessible to those on the wireless network whether from the Internet or from your company s server Configure your access point to your specific settings within minutes 1 Maximum wireless signal rate derived from draft 802 1 1ac specifications Actual data throughput will vary Network conditions and environmental factors including volume of network traffic building materials and construction and network overhead lower actual data throughput rate Environmental factors will adversely affect wireless signal range Wireless range and speed rates are D Link RELATIVE performance measurements based on the wireless range and speed rates of a standard Wireless N product from D Link D Link DAP 1665 User Manual 4 Section 1 Product Overview Hardware Overview Connections EXT Reset Button Pressing the Reset button restores the access point toits original factory default settings LAN Port Connect 10 100 1000 Ethernet devices such as computers switches and hubs Power Switch Press to turn power to the un
69. ork D Link DAP 1665 User Manual 73 Section 5 Connecting to a Wireless Network Connect to a Wireless Network Windows 8 It is recommended to enable wireless security WPA WPA2 on your wireless router or access point before configuring your wireless adapter If you are joining an existing network you will need to know the security key Wi Fi password being used To join an existing network locate the wireless network icon in the taskbar next to the time display 11 33 AM Ty Pie ay D vB tO 91 2013 Wireless Icon Clicking on this icon will display a list of wireless networks which are within connecting proximity of your computer Select the desired network by clicking on the network name Networks Airplane mode Off K SWSWSW ASUS Guest TP PLC Router AirPort Express AirPort Express 5GHz D Link DAP 1665 User Manual 74 Section 5 Connecting to a Wireless Network You will then be prompted to enter the network security key Wi Fi password for the wireless network Enter the password into the box and click Next If you wish to use Wi Fi Protected Setup WPS to connect to the router you can also press the WPS button on your router at this point to enable the WPS function When you have established a successful connection to a wireless network the word Connected will appear next to the name of the network to which you are connected D Link DAP 1665 User Manual Networks d link O7 725 Enter th
70. ork Name SSID dlink 96C 1 5GHz using up to 32 characters Give your Wi Fi network a password Between 8 and 63 characters Between 8 and 63 characters 17 Section 3 Configuration A summary page will be displayed showing the current settings for your 2 4 GHz and 5 GHz wireless networks It is recommended that you make a note of this information for future reference Click Save to save your network settings In order for your network settings to take effect AP will reboot automatically When the device has finished rebooting the main screen will display A dialog box will appear asking if you wish to save the address for the web based configuration utility in your browser s bookmarks Click OK to save and you will be taken to your browser s bookmark settings to save the address Click Cancel to continue without saving a bookmark In order for your network settings to take effect AP will reboot automatically When the device has finished rebooting the main screen will display D Link DAP 1665 User Manual SETUP COMPLETE Please take a note of the following summary of your Wi Fi security settings for future reference 2 4GHz Wi Fi Network Name SSID diink 96C1 5GHz Wi Fi Network Name SSID dlink 96C1 5GHz 2 4GHz Wi Fi Password password SGHz Wi Fi Password password The Setup Wizard has completed Click the Save button to save your settings and reboot the device Message from webpage 8s
71. ou should also select an encryption method from the subsequent drop down menu and enter the WEP key in the field provided If you select WPA you should enter a pre shared key password in the field provided Regardless of the security mode selected the settings should be the same on all access points within the bridge For further information regarding wireless security please refer to Configuring Wireless Security on page 42 Click Save Settings at the top of the page to save the current configuration WIRELESS MODE BRIDGE SETTING Bridge Band 802 11 Mode Wireless Channel Channel Width Remote AP Mac Bridge Security 2 4GHz 5GHz Mixed 802 11ac 802 11n and 802 113 36 Auto 20 40 80MHz L 3 5 T none WEP Key Pre Shared Key 8 63 char Note The Bridge mode is not completely specified in the Wi Fi or IEEE standards This mode will work with other DAP 1665 units Communication with other APs even other D Link APs is not guaranteed D Link DAP 1665 User Manual 32 Section 3 Configuration Wireless Mode Bridge Band 802 11 Mode Wireless Channel Channel Width Remote AP MAC Bridge Security Bridge with AP Mode Select Bridge with AP from the drop down menu Select the wireless band that you wish to use for the wireless bridge 2 4 GHz The bridge can function using 802 11n 802 110 or 802 11g 5 GHz The bridge can function us
72. prior notice Copyright 2010 2011 by D Link Corporation D Link Systems Inc All rights reserved CE Mark Warning This is a Class B product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures Reorient or relocate the receiving antenna Increase the separation between t
73. r Port Optional backup RADIUS server Second RADIUS server IP Address Second RADIUS Server Port Second RADIUS Server Shared Secret 0 0 0 0 1812 44 Section 3 Configuration LAN Setup The LAN Setup page enables you to configure the Local Area Network LAN settings for the access point From this page you can adjust your local network s IP address settings and configure IPV6 Device Name My LAN Connection is IP Address Subnet Mask Gateway Address Primary DNS Server Secondary DNS Server D Link DAP 1665 User Manual Dynamic Static IP You can change the name of your access point to make it easier to identify Enter a name for the access point in the field provided If you change the device name you should use this name in your web browser address bar when trying to access the web based configuration utility Example http devicename Select how you would like to configure the access point s IP address settings from the drop down menu Dynamic IP DHCP The access point will request an IP address from the DHCP server that it is connected to Static IP You can manually specify the IP address settings for the access point Enter the IP address that you want to specify for the access point Static IP only Enter the subnet mask to be used by the access point Static IP only Enter the default gateway address to be used by the access point Static IP only Enter the
74. re running on the computer Software firewalls such as ZoneAlarm BlackICE Sygate Norton Personal Firewall and Windows XP firewall may block access to the configuration pages Check the help files included with your firewall software for more information on disabling or configuring it D Link DAP 1665 User Manual 86 Section 6 Troubleshooting e Configure your Internet settings e Go to Start gt Settings gt Control Panel Double click the Internet Options Icon From the Security tab click the button to restore the settings to their defaults e Click the Connection tab and set the dial up option to Never Dial a Connection Click the LAN Settings button Make sure nothing is checked Click OK e Go to the Advanced tab and click the button to restore these settings to their defaults Click OK three times e Close your web browser if open and open it e Access the web management Open your web browser and enter the IP address of your D Link access point in the address bar This should open the login page for your the web management e If you still cannot access the configuration unplug the power to the access point for 10 seconds and plug back in Wait about 30 seconds and try accessing the configuration If you have multiple computers try connecting using a different computer 2 What can I do if I forgot my password If you forgot your password you must reset your access point Unfortunately this process will change all your set
75. ress use on the network Set Default Gateway the same as the LAN IP address of your router IP address 182 1680 52 192 168 0 1 Subnet mask 255 255 255 0 Default gateway 192 168 0 L Set Primary DNS the same as the LAN IP address of your router 192 168 0 1 The cusetretotonngons sever c der Secondary DNS is not needed or you may enter a DNS server from your ISP Fred DNS parer 192 1689 1 Alternate DNS server p Step 5 Click OK twice to save your settings D Link DAP 1665 User Manual 91 Appendix B Technical Specifications Technical Specifications Standards IEEE 802 11ac e IEEE 802 11b e IEEE 802 11n IEEE 802 3 IEEE 802 119 e IEEE 802 3u Security e WPA WPA2 e WEP Personal e WPS Enterprise Wireless Signal Rate e Up to 1200 Mbps Maximum Transmission Power e 2 4GHz e 5 GHZ 11n 22dBm 11ac 21dBm 11g 22dBm 11a 21dBm 11b 25dBm 11n 20dBm Maximum Operating Voltage 12V1A Power Consumption e 5 18 W Frequency Range e 2 4 GHz Band 2 4 2 4835 GHz e 5 GHz Band 5 15 GHz to 5 35 GHz 5 47 GHz to 5 85 GHz Antennas e Two 2 dBi external antennas or two 3 5 dBi external antennas LEDs e Power e 5 GHz wireless e 2 4 GHz wireless e LAN Temperature e Operating 32 F to 131 F 0 C to 55 C e Storage 20 to 65 C 4 to 149 F Humidity e Operating 10 90 non condensing e Storage 5 95 non condensing
76. router on your network Client Mode D Gaming console Wireless Router Internet D Link DAP 1665 User Manual 10 Section 2 Installation Repeater Mode In Repeater mode the DAP 1665 extends the range of your existing wireless network by repeating the wireless signal of another access point or wireless router The DAP 1665 and wireless router if used must be within range of each other The extended wireless network can use the same SSID and security settings as the existing network or you can choose to specify a new network name and security method Repeater Mode cm Internet Wireless DAP 1665 Router gt Wireless Devices D Link DAP 1665 User Manual 11 Section 2 Installation Bridge Mode In Bridge mode the DAP 1665 creates a wireless link between two existing networks enabling data to be shared between the two networks without the need for a physical connection The two networks must be within wireless reach of one another in order for bridge mode to be effective Note Bridge mode is not specified in the Wi Fi or IEEE standards This mode will only work using two DAP 1665 units Compatibility with other APs even other D Link APs is not guaranteed Bridge Mode i i cc Internet Router DAP 1665 DAP 1665 Router Switch Switch D Link DAP 1665 User Manual 12 Section 2 Installation Bridge with AP Mode Bridge with AP mode has the same features of Bridg
77. rt for WCN 2 0 use software provided by a third party or manually configure If you are running Windows Vista log into the router and click the Enable checkbox in the Basic gt Wireless section Use the Current PIN that is displayed on the Advanced gt Wi Fi Protected Setup section or choose to click the Generate New PIN button or Reset PIN to Default button PIN SETTINGS Current PIM 53468734 Reset PIN to Detain Gena ate her PIN If you are using third party software to set up Wi Fi Protection carefully follow the directions When you are finished proceed to the next section to set up the newly configured router D Link DAP 1665 User Manual 82 Section 5 Connecting to a Wireless Network Using Windows XP Windows XP users may use the built in wireless utility Zero Configuration Utility The following instructions are for Service Pack 2 users If you are using another company s utility or Windows 2000 please refer to the user manual of your wireless adapter for help with connecting to a wireless network Most utilities will have a site survey option similar to the Windows XP utility as seen below If you receive the Wireless Networks Detected bubble click on the center of the bubble to access the utility P Wireless networks detected x One or more wireless networks are in range of this computer To see the list and connect click this message Or Right click on the wireless computer icon in yo
78. sion 1 Current Language Pack Version Current Language Pack Version Check Online Now for Latest Firmware and Language pack Version Check Now Date 2013 07 15 Remove CHECK LATEST FIRMWARE AND LANGUAGE PACK VERSION Latest Firmware Version Latest Firmware Date FIRMWARE UPGRADE Note Some firmware upgrades reset the configuration options to the factory defaults Before performing an upgrade be sure to save the current configuration from the Maintenance gt System screen To upgrade the firmware your PC must have a wired connection to the access point Enter the name of the firmware upgrade file and click on the Upload button Upload LANGUAGE PACK UPGRADE 63 Section 3 Configuration Time Use the Time page to configure the time and date settings of the access point You can also configure daylight saving adjustments and synchronize the access point s clock and calendar with an Internet based Network Time Protocol NTP server Time Displays the access point s current time and date ee Time 07 15 2013 23 28 03 Time Zone GMT 08 00 Pacific Time US amp Canada Tijuana Enable Daylight Check the box to have the access point automatically adjust the Fable Daylight Saving Saving clock for daylight saving Daylight Saving Offset 1 00 Time Zone Select your time zone from the drop down menu Month Week Day of Week Time Daylight Saving Select the offset for beginning daylight savin
79. ssscccsssccecssscersuscessusceessees 8 Advanced Wireless sessista 50 ACCESS Point MOE mme 9 WIFE POTEC TOO O U irtoaa aaae 52 Wireless Client Mode 10 EE a i ncn sere A 53 Repeater MOde rene 11 MVHS SS CNG TE MORE 54 Bridge MOCO nine 12 Advanced Wireless suiriri isisisi rnense 54 Bridge with AP Mode nr 13 BAS MOSS ee iii 55 Wireless Installation Considerat OS 14 ACCESS CONOR ononn 55 Bridge with AP Mode sn 56 COM IQUE ON ssc 2 scene seen ssnst este cos 15 Advanced Wireless 56 Web based Configuration Utility 15 Repeater Mode nee 57 Wireless Setup NI ZA a ns 16 D Link DAP 1665 User Manual ii Table of Contents Access Control e essesesssesesesesesesesseseseseseseseseresessesssesess 57 Advanced Wireless sesesesesesesessesesesesesesesesessssesssesees 58 Wi Fi Protected Setup ss 59 User IME vse na mn 60 MSI TRANS aa 61 AO 61 D ET CUA T E E ATE EEE EE 62 ELLAR a PAE EE A E E AE 63 EE a E AAE E A EE E EE 64 SELE A Gi 65 ST o 9 1210 LE LES 66 Se RE E 67 Device INFO s sessesesesessesesesesssseseseseesesesesssssseseseseesesesesseseseses 67 HOGS na a es 68 Statistics PNR 69 Wireless vo ccccccsssccsssscscscsscsssscsssscssssssscsssscesssssssssscesssceseees 70 FIG UO A EEE E A E 71 Wireless Security sssssossssscossssecossssccssssseosssscossssseossssseo 72 MVS WEP l seareiros aeniea a E A A E EIEEE Ree N 72 What is NP ST aa lea 72 What is WPA a 73 Connect to a Wireless Network 74
80. sting wireless signal can be repeated by the DAP 1665 using both the 2 4 GHz and 5 GHz bands Wireless Mode Site Survey Repeater Network Name Repeater Network Band Channel Width Enable Wireless Repeater Network Name Local Wi Fi Network Name 2 4 GHz Band Select Repeater from the drop down menu Click Site Survey to display a list of wireless networks in your area To select a wireless network click on the radio button in the far right column and click Connect at the bottom of the page to continue The wireless network name will automatically appear in the Repeater Network Name field below and the Repeater Network Band and Channel Width will automatically be detected If you have not used the Site Survey button above enter the SSID of the access point you want to repeat the signal of If you have not used the Site Survey button above select the wireless band of the repeater network If you have not used the Site Survey button above select the channel width to be used for communication with the repeater network Check the box to enable the 2 4 GHz wireless band By default the schedule is set to Always however you can select a schedule from the drop down menu or click Add New to create a new schedule Displays the name of the network to be repeated Choose how you would like to name the DAP 1665 s extended network using the radio buttons Same as Repeater Name The extended network will h
81. ting wireless clients support it Choose a cipher type from the drop down menu Enter the IP address for your network s RADIUS authentication server Enter the port for the RADIUS authentication server Enter the shared secret required by the RADIUS authentication server D Link DAP 1665 User Manual 2 4GHZ WIRELESS SECURITY SETTING Security Mode WPA Mode WPA Personal AUTO WPA or WPA2 L WPA Enterprise AUTO WPA or WPA2 Cipher Type TKIPandAES RADIUS Server IP Address RADIUS Server Port Optional backup RADIUS server Second RADIUS server IP Address Second RADIUS Server Port Second RADIUS Server Shared Secret 0 0 0 0 1512 Section 3 Configuration Advanced Second RADIUS Server IP Address Second Pre Shared Key Second Radius Server Shared Secret Click on the Advanced button to display the setup options for an optional backup RADIUS server configuration Enter the IP address for your network s backup RADIUS authentication server Enter the port for the backup RADIUS authentication server Enter the shared secret required by the backup RADIUS authentication server Click Save Settings at the top of the page to save the current configuration D Link DAP 1665 User Manual 2 4GHZ WIRELESS SECURITY SETTING Security Mode WPA Enterprise WPA Mode AUTO WPA or WPA2 Cipher Type TKIF and AES RADIUS Server IP Address RADIUS Serve
82. tings back to the factory defaults To reset the access point locate the reset button hole on the rear panel of the unit With the access point powered on use a paperclip to hold the button down for 10 seconds Release the button and the access point will go through its reboot process Wait about 30 seconds to access the access point The default IP address is 192 168 0 50 When logging in the username is Admin and leave the password box empty D Link DAP 1665 User Manual 87 Section 6 Troubleshooting 3 Why can t I connect to certain sites or send and receive emails when connecting through my access point If you are having a problem sending or receiving email or connecting to secure sites such as eBay banking sites and Hotmail we suggest lowering the MTU in increments of ten Ex 1492 1482 1472 etc Note AOL DSL users must use MTU of 1400 To find the proper MTU Size you ll have to do a special ping of the destination you re trying to go to A destination could be another computer or a URL e Click on Start and then click Run e Windows 95 98 and ME users type in command Windows NT 2000 and XP users type in cmd and press Enter or click OK e Once the window opens you ll need to do a special ping Use the following syntax ping url f 1 MTU value C ping yahoo com F 1 1482 Pinging yahoo com 66 94 234 13 with 1482 bytes of data Packet needs to fragmented but set Packet needs to fragmente
83. tion of the DAP 1665 you may use the web based configuration utility To access the configuration utility open a web browser A such as Internet Explorer and enter http dlinkap in the gt http dlinkap address field Select Admin from the drop down menu and then enter your password Leave the password blank by default If you get a Page Cannot be Displayed error please refer to Troubleshooting on page 86 for assistance WIRELESS D Link DAP 1665 User Manual 15 Section 3 Configuration Wireless Setup Wizard Click Launch Wireless Setup Wizard to configure your access point Ifyou wantto configure the access point manually without running the wizard skip to Manual Configuration on page 27 Click Next to continue D Link DAP 1665 User Manual SETUP ADVANCED MAINTENANCE STATUS HELP SETUP WIZARD Helpful Hints WIRELESS SETUP z A z p If you are new to If you would like to utilize our easy to use web based wizard to assist you in connecting your networking and have never LAN SETUP DAP 1665 to the wireless network click on the button below configured an access point or before dick on Launch access point will quide you through a few simple steps Note Some changes made using this Setup Wizard may require you to change some settings to get your network up and on your wireless client adapters so they can still connect to the D Link Access Point running WI FI CONNECTION SETUP WIZARD
84. to save the address for the web based configuration utility in your browser s bookmarks Click OK to save and you will be taken to your browser s bookmark settings to save the address Click Cancel to continue without saving a bookmark In order for your network settings to take effect AP will reboot automatically When the device has finished rebooting the main screen will display D Link DAP 1665 User Manual Message from webpage 22 Section 3 Configuration Repeater Mode This wizard is designed to assist you in configuring your DAP 1665 as a repeater to extend the range of your existing wireless network Select Repeater from the drop down menu Select WPS as the configuration method only if your wireless device supports Wi Fi Protected Setup WPS For Manual setup skip to page 25 Click Next to continue Press the WPS Push Button on your existing wireless router with 120 seconds to complete the WPS setup process D Link DAP 1665 User Manual SELECT YOUR OPERATION MODE Please select wireless mode Click Next to continue Repeater mode extends the wireless signal Wireless Mode Repeater from your point increasing your wireless network coverage 9 PC Wirskees Router DAP 1665 in Repeater Mode 9 4 Prev SELECT CONFIGURATION METHOD Please select one of the following configuration methods and click next to continue WPS Select this option if you want to use WiFi Protected Set
85. ttom of the page to continue SWSWSW O PAERD UZ AARE oe ese ee ep dlink1 fc 75 16 76 73 00 149 A N AP no 65 If you do not see your network in the list click Rescan dlink2 fc 75 16 76 73 01 149 A N AP no 63 to search again If the existing wireless network uses wireless security ee enter the Wi Fi Password in the field provided Please enter Wi Fi Password to establish wireless connection Click Next to continue Wi Fi Password D Link DAP 1665 User Manual 25 Section 3 Configuration By default the Wireless Network Name SSID field will display the same network name as the source network If you wish to specify a different name for the extended network enter it in the field provided If you wish to use the same network name check the box below The security password will be the same as that of the source network regardless of whether the network name is the same or not Click Next to continue A summary page will be displayed showing the network name and Wi Fi password for the extended network It is recommended that you make a record of this information for future reference Click Save to save the configuration D Link DAP 1665 User Manual PLEASE ENTER THE SETTINGS FOR THE EXTENDED NETWORK Give your network a name using up to 32 characters Wireless Network Name SSID DIR6261 Use the same security and passphrase as those for the existing network SETUP COMPLETE Please take a note of the fol
86. up Manual Select this option if you want to setup your network manually cancel VIRTUAL PUSH BUTTON Please press the Push Button physical or virtual on the AP or Router you are connecting to within 111 seconds 23 Section 3 Configuration Ifa connection has been successfully made click Finish ADD WI FI DEVICE WITH WPS on the following screen to complete the setup process If the connection was not successful click Retry to try You have successfully connected ta the Wi Fi network again or Cancel to abort the setup process Finish ADD WI FI DEVICE WITH WPS You have failed to connect to the Wi Fi network within the given timeframe please click on the button below to do it again Retry Cancel D Link DAP 1665 User Manual 24 Section 3 Configuration Select Manual configuration to setup your network D ee manually Please select one of the following configuration methods and click next to continue WPS this ins if you want to use WiFi Protected Click Next to continue The wizard will then scan for available wireless networks SELECT WI FI NETWORK within range of the DAP 1665 Find the SSID of the router Se PRES RSR SE MR EEE or access point you wish to extend and click the radio WPA PSK A 07869 5 00 18 e7 95 68 ab 48 A N AP aes thip WPA2 100 button in the Select column PSK aes tkip D Link ic bd b9 c3 3f 40 149 A N AP no 71 WPA PSK Click Connect at the bo
87. ur system tray lower right corner next to the time Select View Available Wireless Change Windows Firewall settings Open Network Connections Networks _ View Available Wireless Networks The utility will display any available wireless networks in your area Click en SR ee e e e Network Tasks oose a wire ess ne or on a network displayed using the SSID and click the Connect button aes ne Refresh network list in the list below to connect to 4 wireless network in range or to get more eer p T 1 If you get a good signal but cannot access the Internet check the TCP nonnes wil Related Tasks default 3 IP settings of your wireless adapter Refer to the Networking Basics TEINTE i UD Learn about wireless Unsecured wireless network all networking pst section in this manual for more information n ie ve hale renier Security enabled wireless network ll J Change advanced settings k Security enabled wireless network Ji rll This network requires a network key If you want to connect to this network dick Connect DGL 4300 n amp D Link DAP 1665 User Manual 83 Section 5 Connecting to a Wireless Network Configure WPA PSK It is recommended to enable WEP on your wireless router or access point before configuring your wireless adapter If you are joining an existing network you will need to know the WEP key being used
88. wireless network or to reduce interference in congested areas If you Balimela jh ol ee enable Auto Channel Scan this option will not be available Security Mode WPA Personal WPA Mode AUTO WPA or WPAT Enable Auto The Auto Channel Scan setting can be selected to allow the Channel DAP 1665 to automatically choose the channel with the least Scan amount ofinterference Cipher Type AES Pre Shared Key password Channel Select the appropriate channel width between 20MHz or Auto Width 20 40MHz from the drop down menu Visibility Select whether you want the wireless network name SSID of Status the 2 4 GHz band to be Visible or Invisible If Invisible the SSID of the DAP 1665 will not be seen by site survey utilities so wireless clients will have to manually enter the SSID of your wireless network in order to connect to it Security For information on how to set up wireless security please refer Mode to Configuring Wireless Security on page 42 Note If the repeater network uses the 2 4 GHz band the Wireless Channel Auto Channel Scan and Visibility Status options will not be available for configuration The DAP 1665 will use the settings of the repeater network for these options D Link DAP 1665 User Manual 38 Section 3 Configuration Enable Wireless Repeater Network Name Local Wi Fi Network Name 802 11 Mode Wireless Channel Enable Auto Channel Scan 5 GHz Band Check the box to enable

Download Pdf Manuals

Related Search

Related Contents

Renseignements - Ville de Noisy-le  Smart Wireless Doorbell User Manual    Costar 9SIR Carbon Monoxide Alarm User Manual  RAPPORT MORAL  TV Xelos 32  Novus QuickMount  Prefácio Características de apresentação  Monacor PAK-15DMP    

Copyright © All rights reserved. Failed to retrieve file