Home

FASTRACK M1200 Series User Guide

1. PIN EIA CCIT Designation RS232 1 DCD 109 Data carrier detect 6 RX 104 Receive data 2 TX 103 Transmit data 8 DTR 108 2 Data terminal ready 9 GND Signal ground 7 DSR 107 Data set ready 12 RTS 105 Request to send 11 CTS 106 Clear to send 13 RI 125 Ring indicator Audio 4 Microphone Not applicable 5 Microphone 10 Speaker 15 Speaker Reset 14 Reset 3 Reserved wavecomconfidential Page 12 27 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement Ce document est la propri t exclusive de WAVECOM Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pr alable WwWavecon D ear 2665 September 2002 2 4 1 2 Power supply connector Figure 5 4 pins Micro Fit connector Table 10 Pin assignment for Power Supply connector Connector Pins layout Comments 4 pins 1 V BATTERY Power Micro Fit 3 0 2 GROUND supply 3 4 AUXI NC Order the 4 pins Micro Fit 3 07 from the supplier Molex 2 4 2 LED function The LED lights indicate the operational status of the modem Refer to following table for a list of the LED states Table 11 Operational states of Fastrack modem MODEM is LED light activity Status of MODEM ON flashing slowly idle mode connected to the network flashing rapidly transmission mode OFF none not connected to th
2. 19 6 1 Receiving no carrier message 2 cece eee eee eens eens eee eeeeeaee eens 19 6 2 Not connecting through the serial link 21 6 3 Receiving error message 22 cee cece eee eee ence ess e e he emere nnns 22 7 NOTES ON SAFETY creer erre rrr enr seen nnn rrr nnn 24 7 1 General Safety scs Rx REX ERR ER RRREXRRERRRERKRERRYRRKRERRNERKRERRRENRTERRNERKRERRSEN 24 47 2 Vehicle Safety iscscueciteesexikeneeta REX Era ROI ORARE Era RELOREA DRE REN REFERRE 25 7 3 Maintenance of GSM modem sise 25 7 4 Your responsibility sisi 26 8 General information Lee ree rere ree ere n en nene 27 8 1 GSM reference documents sisi 27 8 2 EISICOntaGE coi mesi ven bois AA AKART TAN ain e RR en ao EA PER DAC ue 27 8 3 SEVICE P IT M R 27 8 4 DISCIAIMEr eme Er RI L 27 8 5 Trademarks PERROS eee ced Aes EE EE HEC EET 27 8 6 SOO VE E Ud 27 VV OVOGCOMNY confidential Page 5 27 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement Ce document est la propri t exclusive de WAVECOM Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pr alable WOaVeECCOMM WM MKT Fastrack UGD 001 002 September 2002 Tables and Figures Table 1 Physical characteristics o
3. without prior written agreement Ce document est la propri t exclusive de WAVECOM Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pr alable Weve com WM MKT Fastrack UGD 001 002 September 2002 5 4 Verifying network registration of the modem 1 Using the Hyperterminal program type the AT command AT CREG Value appears for the response 2 Verify the result with the following chart Value Network registration 0 1 Yes 0 5 Yes registered roaming Note If the modem is not registered perform the procedure for Verifying signal strength to determine the strength of the received signal VV OVOGCOMNY confidential Page 18 27 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement Ce document est la propri t exclusive de WAVECOM Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pr alable Weve com WM MKT Fastrack UGD 001 002 September 2002 6 Troubleshooting failed transmission This section of the document describes possible problems encountered when using the Fastrack modem and their solutions To review other troubleshooting information refer the FAOs Frequently Asked Questions page at www vwavecom com or use the following link http vvvwvw vvavecom com support fags ph 6 1 Receiving no carrier message If the modem returns a message of no
4. 6 Audio interface characteristics For GSM 900 1800 and GSM 900 1900 Min Typ Max Unit Microphone input voltage minimum gain Speaker output voltage maximum gain Speaker Impedance L 1 65 Vrms L1 do 2 3 GSM features Fastrack modem is GPRS Class 2 capable Following table lists the features of the Fastrack modem Table 7 Features of Fastrack modem MODE DESCRIPTION Audio Half Rate Full Rate Enhanced Full Rate Accessories options handset and car kit Standard Dual Band Extended GSM900 MHz Class 4 2W and GSM 1800 1900 MHz Class 1 1W Interface Serial interface RS232 V 24 V 28 Autobauding function AT command set based on V 25ter and GSMO7 05 amp 07 07 SMS Mobile Originated IVIO and Mobile Terminated IVIT Mode Text amp PDU point to point Cell Broadcast In accordance with GSM 07 05 Data Asynchronous 2400 4800 9600 and 14400 bps Transparent and Non Transparent mode In Non Transparent Mode only 300 1200 1200 75 bauds Mode 3 1 KHz PSTN and V110 ISDN Fax 2400 4800 7200 9600 bps GSM teleservice 62 in transparent mode Class 2 Group 3 compatible GPRS Class 2 Coding schemes CS1 to CS4 Compliant with SMG31bis wavecomconfidential Page 10 27 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement Ce document est la propri t exclusive de WAVECOM Il ne peut t
5. clean and properly inserted into the holder 11 SIM PIN required Enter PIN code 12 SIM PUK required Enter PUK code Note Call your network provider if you do not know this code 13 SIM failure Check validity of your SIM card If SIM damaged call your network provider 16 Incorrect password Check the code you entered 17 SIM PIN2 required Enter PIN2 code 18 SIM PUK2 required Enter PUK2 code Note Call your network provider if you do not know this code 26 Dialing string too long Check the phone number max 20 digits 30 No network service No action 32 Network not allowed No action emergency calls only 40 Network personalization PIN Enter the Network lock required Network lock Note Call your network provider if you do not know this code 103 Illegal MS 3 No action 106 legal ME 6 No action 107 GPRS services not allowed Contact your network provider to 7 subscribe to the GPRS service 111 PLMN not allowed 11 No action 112 Location area not allowed No action 12 113 Roaming not allowed in this No action location area 13 132 service option not supported Check the service option 32 133 requested service option not Call your network provider to subscribe subscribed 33 to the requested service option 134 service option temporarily No action out of order 34 149 PDP authentication failure Call your network provider to know the right authentication parameters 150 invalid mobile class Change the class of the mob
6. manual is available from your local modem supplier 8 4 Disclaimer Modem and GSM unit specifications and manuals are subject to change without notice Wavecom assumes no liability for damage incurred directly or indirectly from errors omissions or discrepancies between the modem or GSM unit and their manuals 8 5 Trademarks Some mentioned products are registered trademarks of them respective companies 8 6 Copyright This manual is copyrighted by Wavecom with all rights reserved No part of this manual may be reproduced in any form without the prior written permission of Wavecom No patent liability is assumed with respect to the use of the information contained herein wavecomconfidential Page 27 27 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement Ce document est la propri t exclusive de WAVECOM Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pr alable
7. names mentioned may be trademarks or registered trademarks of their respective owners WAVECOM S A may at any time and without notice make changes or improvements to the products and services offered and or cease producing or commercializing them wavecomconfidential Page 3 27 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement Ce document est la propri t exclusive de WAVECOM Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pr alable WeaVe eCOAMNA WM MKT Fastrack UGD 001 002 September 2002 Contents Document Information e erre eurer eer ree ener eue 2 LO Ta i e p 3 Contents ee eee eee eee 4 Tables and Figures lrr lure erre enr r rrr rnm rrr rmn rrr urn 6 1 Product description rr lrr rrr rere r rrr rrr eee 7 2 Product details ecce uu uuna RR RR RREREMRRRARARERRRARRANARAREENRREHARANEANEA anus 7 2 1 Physical characteristics ssssssssssssssssssssssssss ss e ese e sh ensem 7 2 2 Electrical characteristics ssssssssssssssseesssssssss seen ness sess 8 2 2 1 Power CONSUMPTION sssirresrerkrire keinin ir rans ERR RNRERRRZERRE RR IRA E 4 RGaa Ya n ant 9 2 2 2 Audio interface sssssssssssssssssesss esses sss asse assi nass
8. of GSM Modem e Do contact an authorized Service Center in the unlikely event of a fault wavecomconfidential Page 25 27 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement Ce document est la propri t exclusive de WAVECOM Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pr alable wavecom D ear 2605 September 2002 7 4 Your responsibility This GSM Modem is under your responsibility Please treat it with care respecting all local regulations It is not a toy Therefore keep it in a safe place at all times and out of the reach of children Remember your Unlock and PIN codes Become familiar with and use the security features to block unauthorized use and theft wavecomconfidential Page 26 27 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement Ce document est la propri t exclusive de WAVECOM Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pr alable WOaVeECCOMM WM MKT Fastrack UGD 001 002 September 2002 8 General information 8 1 GSM reference documents GSM 03 40 GSM 03 45 GSM 04 11 GSM 04 21 GSM 05 08 GSM 07 01 GSM 07 02 GSM 07 05 GSM 07 07 8 2 ETSI contact ETSI Secretariat F 06921 Sophia Antipolis Cedex France e mail secretariat etsi fr 8 3 Service The AT commands
9. using the ATH command Is the selected bearer type is supported by the called party Is the selected bearer type is supported by the network Type AT CMEE to view the extended error code Note Refer to Table 18 Ensure that the selected bearer type is supported by the called party Ensure that the selected bearer type is supported by the network Ensure that the semicolon is typed immediately after the phone number n the AT command e g AID Is the received signal strong enough Refer to 8 4 to verify the strength of the received signal Is the antenna connected properly Refer to Table 12 for antenna requirements wavecomconfidential This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement Ce document est la propri t exclusive de WAVECOM Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pr alable Page 22 27 wavecon WM_MKT_Fastrack_UGD_001 002 September 2002 Table 18 Interpretation of extended error codes Error Diagnostic Hint Code O Phone failure Call technical support 3 Operation not allowed No action 4 Operation not supported 10 SIM not inserted Do one of the following Insert the SIM card in the SIM holder of the modem Check that the SIM card is
10. Aluminium wavecomconfidential Page 7 27 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement Ce document est la propri t exclusive de WAVECOM Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pr alable WOaVeECCOMM WM MKT Fastrack UGD 001 002 September 2002 Micro Fit connector Front cap SUB HD connector connector Figure d Extractible Modem presentation SIM holder Figure 1 Fastrack presentation To ensure proper operation of the Fastrack modem the operating environment must be within a specific temperature range as described in following table Table 2 Optimal operating and storage temperatures Operating temperature range 20 C to 55 C Storage temperature range 25 C to 70 C 2 2 Electrical characteristics The Fastrack modem is permanently ON once you connect the power supply cable to a functional power supply see Figure 2 Correct operation of the Fastrack modem is optimum in the following voltage range Table 3 Operating voltage Operating voltage range 5 to 32 V Ground OV OV The following table describes the consequences of overvoltage and undervoltage with the Fastrack modem Table 4 Effects of power supply defect If the voltage Then the falls below 5 V communication is not guaranteed undervoltage continuously pe
11. aks modem is protected by the fuse above 32V overvoltage power supply disconnects the electronic components from overvoltage transiently peaks modem guarantees its own protection above 32 V overvoltage wavecom confidential Page 8 27 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement Ce document est la propri t exclusive de WAVECOM Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pr alable Weve com WM_MKT_Fastrack UGD 001 002 September 2002 As shown in Figure 2 the power supply cable is a tin copper wire with a e core of 24 mm x 0 2 mm e cross section of 0 75 mm Cables stripped over 200 mm Stripped wire tinned over 5 mm TM protected by their own sheath Connector Molex Micro Fit 3 0 Standard cable sheath Side view I AL De UD Figure 2 Diagram of power supply cable 2 2 1 Power Consumption Following table provides information on power consumption of the Fastrack modem assuming an operating temperature of 25 C Table 5 Power Consumption ep Hc ie pe ae Min Typ Max Min Typ Max Input Peak Supply Current pe R o132V 073 onja 32v 0 36 A Input average supply current L 5V mA communication mode 9 132V mA 32v_ mA Input average
12. anufacturers of the medical device to determine if it is adequately protected e Operation of your GSM Modem close to other electronic equipment may also cause interference if the equipment is inadequately protected Observe any warning signs and manufacturers recommendations The modem is designed for and intended to be used in fixed and mobile applications Fixed means that the device is physically secured at one location and is not able to be easily moved to another location Mobile means that the device is designed to be used in other than fixed locations and generally in such a way that a separation distance of at least 20 cm 8 inches is normally maintained between the transmitter s antenna and the body of the user or nearby persons The Modem is not designed for or intended to be used in portable applications within 20cm of the body of the user and such uses are strictly prohibited VVOVOGCOMNY confidential Page 24 27 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement Ce document est la propri t exclusive de WAVECOM Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pr alable wavecom ED ear 665 September 2002 7 2 Vehicle Safety Follow these guidelines for use of the modem in an automobile e Do not use your GSM Modem while driving unless equipped with a correctly installed vehicle kit allowing Hands Fr
13. carrier upon an attempted transmission of data or voice signals then refer to following table for possible causes and solutions Table 14 Solutions for no carrier message If the modem Then ask Action returns no carrier Is the selected bearer type Type AT CEER to view the is supported by the called extended error code Refer to party Table 15 Is the selected bearer type Ensure that the selected is supported by the bearer type is supported by network the called party Ensure that the selected bearer type is supported by the network ensure that the semicolon is typed immediately after the phone number In the AT command e g AID type AT CBST 0 0 3 Configure the SIM card for data fax calls IS the received signal Refer to 8 4 to verify the strong enough strength of the received signal Is the antenna properly Refer to Table 12 for antenna connected requirements Refer to the AT commands manual for all codes and details VVOVOGCOMNY confidential Page 19 27 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement Ce document est la propri t exclusive de WAVECOM Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pr alable WVWoOWVOGCO AA WM MKT Fastrack UGD 001 002 September 2002 Table 15 Interpretation of extended error codes Erro
14. dential Page 14 27 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement Ce document est la propri t exclusive de WAVECOM Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pr alable WVWoOWVOGCO AA WM MKT Fastrack UGD 001 002 September 2002 4 Testing the configuration of Fastrack Following table contains AT commands Use these commands to perform initial tests of the modem configuration Table 13 Testing Fastrack configuration Task AT Module Comments commands Enter PIN Code AT CPIN 1234 OK PIN Code accepted CME ERROR 16 Incorrect PIN Code with CMEE 1 mode CME ERROR 3 PIN already entered with CMEE 1 mode Module AT CREG CREG lt mode gt Modem synchronized on synchro 1 the network checking CREG 2 mode Synchronization lost 2 resynchronization attempt CREG lt mode gt Modem not synchronized O on the network no synchronization attempt Receiving an ATA RING Answer the call incoming call OK ATD1234 Do not forget the at the end for voice calls OK Communication Initiate a call established CME ERROR 11 PIN code not entered with CMEE 1 mode CME ERROR 3 AOC credit exceeded or a communication is already established Initiate an ATD112 OK Do not forget the at emergency call the end for voic
15. e calls Communication NO CARRIER loss Hang up ATH OK Store the AT amp W OK Configuration settings are parameters in E2P stored in E2P waveconCMcontidential Page 15 27 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement Ce document est la propri t exclusive de WAVECOM Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pr alable wavecom D ear 2665 September 2002 5 Getting started with Fastrack 5 1 Mounting Fastrack To mount the Fastrack modem do the following 1 Place the modem at the desired location on the equipment 2 Bind the modem to the equipment using the holding bridles Refer to the following diagram Note To be attached to a plain surface Screw head max height 2mm p i E Figure 2 E Modem mounting N Figure 7 Fastrack mounting wavecomconfidential Page 16 27 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement Ce document est la propri t exclusive de WAVECOM Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pr alable Weve com WM MKT Fastrack UGD 001 002 September 2002 5 2 Installing Fastrack modem The Fastrack modem requires the power supply connection to begin operation It also requires a SIM card to operate on a GSM netwo
16. e network 2 4 3 External antenna The external antenna connects to the modem via the SMA connector Use an antenna with the characteristics listed in follovving table Table 12 External antenna characteristics Antenna frequency dual band GSM 900 1800 MHz antenna for M1203 range or dual band GSM 900 1900 MHz antenna for M1213 or triple band GSM 900 1800 1900 MHz antenna for M1200 series Impedance 50 Q Gain antenna cable O dBi VSWR antenna cable 10 dB wavecomMconfidential Page 13 27 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement Ce document est la propri t exclusive de WAVECOM Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pr alable wavecom SUIS ese dicU EB ear 2605 September 2002 2 4 4 SIM interface Fastrack modem requires Micro SIM card and supports 3V and 5V SIM cards The SIM interface of the Fastrack modem uses an extractible SIM card holder SIM card Extractible SIM card holder Yellow button to eject the holder with a sharp element Figure 6 SIM card holder 3 Accessories Following accessories are recommended with the Fastrack modem e Dual band antenna ALLGON 1140 26 e Antenna adaptor SMA FME adaptor from PROCOM e Power adaptor Europe EGSTON N2 EFSVW 12V 1A mounted with Micro fit connector from MOLEX VV OVOGCOMNY confi
17. ee Operation e Respect national regulations on the use of cellular telephones in vehicles Road safety always comes first e If incorrectly installed in a vehicle the operation of GSM Modem telephone could interfere with the correct functioning of vehicle electronics To avoid such problems ensure that the installation has been performed y a qualified personnel Verification of the protection of vehicle electronics should form part of the installation e The use of an alert device to operate a vehicle s lights or horn on public roads is not permitted 7 3 Maintenance of GSM modem Your GSM Modem is the product of advanced engineering design and craftsmanship and should be treated with care The suggestions below will help you to enjoy this product for many years e Do not expose the GSM Modem to any extreme environment where the temperature or humidity is high e Do not attempt to disassemble the GSM Modem There are no user serviceable parts inside e Do not expose the GSM Modem to water rain or spilt beverages It is not waterproof e Do not abuse your GSM Modem by dropping knocking or violent shaking Rough handling can damage it e Do not place the GSM Modem alongside computer discs credit or travel cards or other magnetic media The information contained on discs or cards may be affected by the phone e The use of third party equipment or accessories not made or authorized by Wavecom may invalidate the warranty
18. f Fastrack modem 7 Table 2 Optimal operating and storage temperatures 8 Table 3 Operating voltage 1 niens etesex censa Emp eE npa beu Lxx ba Erga XE LR Ra ER Xd ERE ERR SER 8 Table 4 Effects of power supply defects 8 Table 5 Power Consumption ccc ccc eee eee eee eee ee ese senes sensns nnns 9 Table 6 Audio interface characteristics 10 Table 7 Features of Fastrack modem sisi 10 Table 8 Fastrack Connectors ice vd xd xx heed ERRARE RR RIA EF REP EFRYEDS EFFERRE EREYgad 11 Table 9 Pins assignment for15 pins SUB D Connector cccee cece eee eee eees 12 Table 10 Pin assignment for Power Supply connector esses 13 Table 11 Operational states of Fastrack modem 13 Table 12 External antenna characteristics esses 13 Table 13 Testing Fastrack configuration 15 Table 14 Solutions for no carrier message 19 Table 15 Interpretation of extended error codes cc ccc ce cece eee enact eenaeeeeenees 20 Table 16 Solutions for no connection through serial link 21 Table 17 Solutions for error message issues 22 Table 18 Interpretation of extended error codes cc ccc ce cece eee eee eeeenaeeeeneeees 23 Figure 1 Fastrack presentation cece eect ee eee eee senem ensem enne 8 Figure 2 Diagram of power supply cable ss 9 Figure 3 SMA connector siemens 11 Figure 4 15 pins SUB D connector high density 12 Figure 5 4 pins Mic
19. ile to a valid one 148 unspecified GPRS error No action wavecomconfidential This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement Ce document est la propri t exclusive de WAVECOM Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pr alable Page 23 27 wavecom SUIS ese dicU Epod 2665 September 2002 7 NOTES ON SAFETY 7 1 General Safety It is important to follow any special regulations regarding the use of radio equipment due to the possibility of radio frequency RF interference Please carefully follow the safety advice given below e Switch OFF your GSM Modem when in an aircraft The use of cellular telephones in an aircraft may endanger the operation of the aircraft disrupt the cellular network and is illegal Failure to observe this instruction may lead to suspension or denial of cellular telephone services to the offender or legal action or both e Switch OFF your GSM Modem when at a refueling point e Switch OFF your GSM Modem in hospitals and any other place where medical equipment may be in use e Respect restrictions on the use of radio equipment in fuel depots chemical plants or where blasting operations are in progress e There may be a hazard associated with the operation of your GSM Modem close to inadequately protected personal medical devices such as hearing aids and pacemakers Consult the m
20. m powered Provide a power supply in the correctly range of 5 to 32V Is the serial cable properly connected to the modem and PC sockets Connect the cable as shown in Figure 4 Verify reception and transmission Is the communication program properly configured Ensure the follovving settings for the modem Data bits 8 Parity none Stop bits 1 Baud 9600 bps Is there another program interfering with the communication program Close the application e g mouse or printer driver wavecomconfidential This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement Ce document est la propri t exclusive de WAVECOM Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pr alable Page 21 27 WVWoOWVOGCO AA 6 3 Receiving error message If the Fastrack modem WM MKT Fastrack UGD 001 002 September 2002 returns a message of error upon an attempted transmission of data or voice signals then refer to following table for possible causes and solutions Table 17 Solutions for error message If the modem Then ask Action returns error Is the modem registered on Refer to 8 5 4 to verify that the the network modem is the network registered on Is the modem receiving an incoming call or is it already in communication End any communication
21. r Code Diagnostic Hint 1 Unallocated phone number Not applicable 16 Normal call clearing 17 User busy 18 No user responding 19 User alerting no answer 21 Call rejected 22 Number changed 31 Normal unspecified 50 Requested facility not Check your subscription data subscribed subscription available 68 ACM equal or greater Credit of your pre paid SIM card than ACMmax expired 252 Call barring on Not applicable outgoing calls 253 Call barring on incoming calls 3 6 8 29 34 38 41 42 43 44 47 49 57 58 63 65 69 70 79 254 Network causes Call network provider See AT commands manual for further details wavecomconfidential This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement Ce document est la propri t exclusive de WAVECOM Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pr alable Page 20 27 WVWoOWVOGCO AA WM MKT Fastrack UGD 001 002 September 2002 6 2 Not connecting through the serial link If the modem does not answer through the serial link upon an attempted transmission of data or voice signals then refer to following table for possible causes and solutions Table 16 Solutions for no connection through serial link If the modem Then ask Action returns nothing Is the mode
22. re communiqu ou divulgu des tiers sans son autorisation pr alable wavecom D ear 2605 September 2002 2 4 Hardware interfaces The hardware interfaces which exist for the Fastrack modem include the plugs sockets wires and the electrical pulses traveling through them in a particular pattern The Fastrack interfaces include e LED function e External antenna via SMA e Serial and control link via 15 pins SUB D e Power supply via 4 pins Micro Fit e SIM interface 2 4 1 Connectors Refer to the following table for the connectors that exist for the Fastrack modem Table 8 Fastrack connectors Connector Function Refer to SMA RF antenna connector Figure 3 15 pins SUB D RS232 link Figure 4 high density AUDIO link RESET 4 pins Micro Fit Power supply connector Figure 5 SIM connector SIM card connection Figure 6 antenna connector Figure 3 SMA connector wavecomconfidential Page 11 27 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement Ce document est la propri t exclusive de WAVECOM Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pr alable wavecom SURG ese dicU endi 2605 September 2002 2 4 1 1 SUB D connector details Figure 4 15 pins SUB D connector high density Table 9 Pins assignment for15 pins SUB D Connector
23. rk To install the modem do the following 1 Connect the power supply cable into the power supply with a correct GND connection Note for automotive application according to the type of application you can use permanent recommended or key switched 2 Press the SIM card holder ejector yellow button with the tip of a pen or use another sharp object 3 Insert the SIM card in the holder 4 Verify that the SIM card fits in the holder properly 5 Connect the antenna to the SMA connector 6 Connect both sides of the serial and control cable 15 pin Sub D connector on the modem side 7 Activate the power supply Plug the power supply cable into the Fastrack modem Note Refer to Figure 1 for a general presentation of the Fastrack modem Refer to Figure 6 for insertion of the SIM card 5 3 Verifying signal strength The Fastrack modem establishes a call if the signal is sufficiently strong To verify the signal strength do the following 1 Using the Hyperterminal program type the AT command AT CSQ Value appears for the received signal strength 2 Verify the result with the following chart Value of signal strength Signal strength AT CSO response RSSI 11 31 sufficient 0 10 insufficient greater than 99 based on general observations VVOVOGCOMNY confidential Page 17 27 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged
24. ro Fit connector 4 444 13 Figure 6 SIM card holder sise 14 Figure 7 Fastrack mounting issues 16 VVOVOGCOMNY confidential Page 6 27 This docu ment is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement Ce docum ent est la propri t exclusive de WAVECOM Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pr alable Weve com WM MKT Fastrack UGD 001 002 September 2002 1 Product description The Fastrack modem is small fast and efficient It supports the transmission of data fax e short messages Point to Point and Cell Broadcast e voice calls The Fastrack modem is a Dual Band product using GSM 900 1800 MHz or GSM 900 1900 MHz and is GPRS class 2 capable The basic elements you receive allow simple installation and operation of the modem The package includes e 1 Fastrack modem M1203 or M1213 e 2 holding bridles e 1 power supply cable e 1 fuse e 1 user guide 2 Product details 2 1 Physical characteristics The Fastrack modem is small and lightweight Following table contains information on the physical characteristics of the Fastrack modem Table 1 Physical characteristics of Fastrack modem Dimensions 98 mm x 54 mm x 25 mm excluding connectors Overall 110 mm x 54 mm x 25 mm Dimensions Weight lt 130 grams Volume 13 23 cm Housing
25. sss nsn nnn 10 2 3 GSM features eie De Er nes Nan dna deta ial awe iE RENERE 10 2 4 Hardware interfaces 0 ccc cece cece eee e eee n eee sees esse assis sa sss assis ass nnn 11 2 4 1 CONME CONS dies cetus games excep rtes x b eas ee a a a tenus dede unus 11 2 4 1 1 SUB D connector details 12 2 4 1 2 Power supply connector csse semen 13 2 4 2 LED f nctiOoDr iili ieuliceiiiiiseiid i e nii Rp e i Sand dak Duke gra o R20 DER ane 13 2 4 3 External anten Mavcccss sees ete sont aa ncenewev aren VP NE DR a RA 13 2 4 4 SUING hea COs EOD ILI EE 14 3 ACCOeSSOT VFIBS 4 RARARARHEHARARRARAREAREARHARNASARARRRRRRRARRAEERSRRRARRANNHARERARRNERA 14 4 Testing the configuration of Fastrack 15 5 Getting started with Fastrack 16 5 1 IVlountirig Eastrack e ihritbetesea tuu era hoixe nent niet UR I bU EINER 16 5 2 Installing Fastrack modem sisi 17 5 3 Verifying signal strength sise 17 5 4 Verifying network registration of the modem 18 wavecomconfidential Page 4 27 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement Ce document est la propri t exclusive de WAVECOM Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pr alable WwWavecon WU uisi D ear 2605 September 2002 6 Troubleshooting failed transmission
26. supply current igev ImA idle mode 132V mA 32v_ mA Input average supply current s ImA idle mode with RS232 autoshutdown 13 2V ImA o32v mA Input average supply current jgsv mA idle mode with full autoshutdown 13 2v ImA m RS232 driver MAX3238 automatically shuts down after 30s of inactivity on the serial link A 31313133 P Pl gt gt gt 3 3 gt gt 130 65 31 4 13 2 56 88 at 22 E 5 3131313 gt gt gt gt es ae L ae 9 o 107 814 13 2 56 mA 88 Sarre nn 22 q a a Jen res 5 RS232 driver in auto shutdown and AT command The power consumption might vary by 5 over the whole operating temperature range 20 C to 55 C The tests are carried out with a 3V SIM card wavecomconfidential Page 9 27 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement Ce document est la propri t exclusive de WAVECOM Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pr alable Wave con WM MKT Fastrack UGD 001 002 September 2002 2 2 2 Audio interface The audio interface is available through the serial and control cable using a headset Electrical characteristics of the audio interface are available in the following table Table
27. wavecon Fastrack M1200 series User Guide Reference WM IVIKT Fastrack UGD OO1 Revision 002 Date September 2002 VV OVOGCOMNY confidential Page 1 27 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement Ce document est la propri t exclusive de WAVECOM Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pr alable Wave con WM_MKT_Fastrack UGD 001 002 September 2002 Document Information Revision Date History of the evolution 001 June O2 Creation 002 Sept O2 Complete Revision VV OVOGCOMNY confidential Page 2 27 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement Ce document est la propri t exclusive de WAVECOM Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pr alable wavecom ED ear 665 September 2002 Overview This document describes the hardware interface and the technical specifications of the Fastrack M1200 series modems e M1203 EGSM GPRS 900 1800 MHz version e M1213 EGSM GPRS 900 1900 MHz version These products are based on dual band WISMO module and are GPRS class 2 capable WAVECOM and WISMO are trademarks or registered trademarks of Wavecom S A in France or in other countries All other company and or product

FASTRACK M1200 Series User Guide

Contents

Download Pdf Manuals

Related Search

Related Contents