Shure PSM 200 User Guide (English)
Contents
1. Audio Inputs and Outputs The INPUT knobs control both MIC and LINE level signals As a general guide line set the knob to the left of twelve o clock for line level signals and to the right of twelve o clock for microphone levels Observe the signal clip LEDs If they are consistently red de crease the levelwith the corresponding INPUT knob NOTE If the level is decreased all the way and the LED N remains red the level of the input from the previous device in the audio chain mixer click track digital sequencer etc is too high and should be decreased To pass audio signal directly through the TransMixer use the corresponding SPLIT OUT on the rear panel of the device Input setting do not affect the level of the signal at the SPLIT OUT connectors The P2T inputs have limiting circuitry that activates automati cally when the input level is too high Phantom Power SPLIT OUTS o oJ KO 2 1 E O 5 SELECT Button Press to select a frequency channel 6 Antenna Permanently mounted break resistant anten na transmits the mix to the P2R Receiver 7 Power Cord Strain Relief Thread the power cable through these slots to secure the DC connection 8 DC IN Plug the power supply into this connector The unit remains powered on until you unplug it 9 SPLIT OUTs Each male XLR output jack duplicates the signal of the corresponding mic line input Front panel settings have no effect on s2. SHURE Model PSM200 User Guide PSM 200 Personal Monitor System User Guide Guide de l utilisation du systeme de retour personnel Personal Monitor System Bedienungsanleitung Guia del usuario del sistema de monitoreo personal Guida all uso del sistema di monitoraggio personale Manual do Usuario do Sistema de Monitora o Pessoal gt gt SCL2 a CE 2008 Shure Incorporated ENGLISH WARNING USING THIS SYSTEM AT EXCESSIVE VOLUMES CAN CAUSE PERMANENT HEARING DAMAGE USE AS LOW A VOLUME AS POSSIBLE In order to use this system safely avoid prolonged listening at excessive sound pressure levels Please use the following guidelines established by the Occupational Safety Health Administration OSHA on maximum time exposure to sound pressure levels before hearing damage occurs It is 90 dB SPL at 8 hours 95 dB SPL at 4 hours 100 dB SPL at 2 hours 105 dB SPL at 1 hour 110 dB SPL at 1 2 hour 115 dB SPL at 15 minutes 120 dB SPL avoid or hearing damage may occur difficult to measure the exact Sound Pressure Levels SPL present at the eardrum in live applications In addition to the volume setting on the PSM the SPL in the ear is affected by ambient sound from floor wedges or other devices The isolation provided by the fit of quality earphones is also an important factor in determining the SPL in the ear Here are some general tips to follow in the use of this product to protect your ears from damage 1
3. 2 3 Turn up the volume control only far enough to hear properly Ringing in the ears may indicate that the gain levels are too high Try lowering the gain levels Have your ears checked by an audiologist on a regular basis If you experience wax buildup in your ears stop using the sys tem until an audiologist has examined your ears Wipe the earphones with an antiseptic before and after use to avoid infections Stop using the earphones if they are causing great discomfort or infection This symbol indicates important operating and maintenance instructions in the literature accompanying this unit LICENSING INFORMATION THIS RADIO EQUIPMENT IS INTENDED FOR USE IN PROFESSIONAL ENTERTAINMENT AND SIMILAR APPLICATIONS Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate the equipment Licens ing of Shure wireless microphone equipment is the user s responsibility and licensability depends on the user s classification and application and on the selected frequency Shure strongly urges the user to contact the appropriate telecommunications authority concerning proper licensing and before choosing and ordering frequencies NOTE THIS EQUIPMENT MAY BE CAPABLE OF OPERATING ON SOME FREQUENCIES NOT AUTHORIZED IN YOUR REGION PLEASE CONTACT YOUR NATIONAL AUTHORITY TO OBTAIN INFORMATION ON AUTHORIZED FREQUENCIES FOR WIRELESS MICROPHONE PRODUCTS IN YOUR REGION Licensing Note that a m
4. 8440 Shure Europe at 49 1731 72140 Shure Asia at 852 2893 4290 or visit theTechnical Support section at www shure com H2 R8 Q3 5 CHANNEL 518 554 MHz 800 814 MHz 748 784 MHz 842 865 MHz North America Europe Europe France Australia England 518 750 801 100 749 100 855 275 ht TE 802 325 802 325 754 025 856 175 a TA 525 625 805 050 756 000 857 625 D TY Ds rs rasen rosso ids ps0 5000000 ds o Ja oo reno eo Wired Mode RF Disabled 13 Certifications P2T Certified to FCC Part 74 FCC ID No DD4P2T Certified in Canada by IC to RSS 123 and RSS 102 Certification No 616A P2T This class B digital apparatus complies with Cana dian ICES 003 EP2T UKP2T Meets essential requirements of European R amp TTE Directive 99 5 EC eligible to bear the CE mark lt 0682 O Type approved to EN 300 422 Parts 1 and 2 Meets require ments of EMC Standard EN 301 489 Parts 1 and 9 P2R Approved under the Declaration of Conformity DoC provision of FCC Part 15 Certified in Canada by IC to RSS 123 Certification No 616A P2R This class B digital apparatus com plies with Canadian ICES 003 Meets essential requirements of European Union R amp TTE Directive 99 5 EC eligible to bear C mark Meets requirements of EMC standards EN 300 422 Parts 1 and 2 and EN 301 489 Parts 1 and 9 APPENDIX P2R Receiver MIX IN Jack Wiring Diagram Mono Line Input The MIX IN jack accepts line level signals such as click tracks ef
5. In short no matter whatthe output device youcan probably plugitinto the TransMixer The complete PSM200 System includes the SCL2 Earphones which feature Dynamic MicroDrivers that produce crisp full spectrum sound They include a variety of sleeve options to provide the best fit and isolation for your ears The SCL2 like all Shure earphones work well with CD players MP3 players and anything else with a 1 8 inch 3 5mm stereo output e Mono mix Up to 4 systems can be operated simultaneously Input level controls e Tricolor LED input level indicators e 1 4 inch line level input jack to connect monitor mix click tracks effects or condenser microphones e Integrated cable management groove secures cables con nected to the bodypack THE P2T TRANSMIXER Controls and Features ENGLISH FRONT PANEL MICILINE 1 MICILINE 2 BACK PANEL Z SHURE INCORPORATED EVANSTON IL 60202 MADE IN USA FCC 1D DD4P2T IC B16AP2T CE wO 1 MIC LINE INPUT Jacks Electronically balanced inputs that accommodate both XLR and 1 4 inch connectors atomic or line levels 2 Signal Clip LEDs Color indicates the signal status of the corresponding MIC LINE input as explained in the Audio Inputs and Outputs section below 3 INPUT Knobs Control the level of their corresponding inputs 4 CHANNEL LED Indicator Displays the frequency chan nel that is being transmitted 1 8
6. many advantages of in ear monitoring including e Improved Sound Quality high fidelity without the risk of feedback e Increased Mobility your mix moves with you e Personal Control create a personal mix and control your own levels For information on this and other Shure products visit www shure com on the World Wide Web The PSM200 Personal Monitor System The PSM200 is a frequency agile in ear monitor system for use in a wide variety of applications Its many features help overcome the difficulties associated with stage monitoring The P2R Receiver is the world s first bodypack receiver to func tion as a wired receiver a wireless receiver or both at the same time This and other unique features along with excellent sound quality make the P2R an exceptional value The P2T TransMixer is another breakthrough design for in ear monitoring It allows the user to connect two line levelor mic FEATURES PSM200 System e 8 selectable UHF frequencies e Includes SCL2 Dynamic MicroDriver earphones P2T TransMixer e 2 mic line XLR 1 4 inch combo inputs e XLR SPLIT OUT connectors P2R Receiver e Combination wired wireless compatibility Gain switch for setting line input sensitivity level inputs directly into the transmitter The two signals can then be mixed independently You can connect microphones or instruments directly to the inputs use line outputs from a mixing console or connect it to Shure s Aux Pander
7. undesired operation Shure Inc Manufacturer Signed Cag PRA Name Title Craig Kozokar EMC Project Engineer Global Compliance Shure Ir Date _nigAcH 206 EU DECLARATION OF CONFORMITY We Shure Incorporated of 5800 Touhy Avenue Niles Illinois 60714 4608 U S A Phone 847 600 2000 Web www Shure com Declare under our sole responsibility that the following product Model P2T Description TransMixer conforms to the essential requirements of European R amp TTE Directive 1999 5 EC The product complies with the following product family harmonized or national standards EN 301 489 Part 1 and 9 ETSI 300 422 1 and ETSI 300 422 2 EN 60065 EN61000 3 2 EN 61000 3 3 The technical documentation is kept at Shure Incorporated Corporate Quality Engineering Division SHURE Europe GmbH EMEA Approval Manufacturer Shure Incorporated Fon Date 16 November 2004 Signed aig Koz kar EMC Project Engineer Corporate Quality Engineering Division Name and Title European Representative SHURE Europe GmbH Signed Date 16 November 2004 Headquarters Europe Middle East amp Africa Wannen cker Str 28 D 74078 Heilbronn Germany Phone 49 0 7131 7214 0 Fax 49 0 7131 7214 14 91 SHURE www shure com United States Shure Incorporated 5800 West Touhy Avenue Niles IL 60714 4608 USA Phone 847 600 2000 Fax 847 600 1212 Email info shure com 2008 Shure Incorpor
8. CATIONS PSM200 System RF Carrier Frequency Range 518 865 MHz country dependent Operating Range 100 m 300 ft under optimal conditions Audio Frequency Response 30 Hz to 12 kHz 3 dB earphone dependent Total Harmonic Distortion 1 kHz lt 1 5 typical Ref 35 kHz deviation P2T TransMixer RF Output Power 30 mW 15 dBm typical conducted country dependent Modulation Limiter Internal peak limiter gt 10 1 hard knee compression Antenna 1 4 Wavelength semi rigid PCB Mount 12 Optional Equipment AuxPander The Shure AuxPander auxiliary expander extends the capabili ties of a standard mixing console by providing eight additional auxiliary sends It is designed ideally for use with multiple personal monitoring systems P2R Receiver 1 4 inch mono 20 foot cable P4M The P4M is a highly versatile four channel two bus stereo mic line mixer designed to optimize personal in ear monitor sys tems in live performance applications denna RE PRO ERR RR 90B4677 Modulation FM 35 kHz Deviation Nominal Signal to Noise Ratio 80 dB typical A weighted Operating Temperature 7 Cto 49 C 20 F to 120 F Current 170 mA maximum Dimensions 220 mm x 140 mm x 40 mm 8 6 in x 5 6 in x 1 7 in Net Weight 370 g 13 oz ENGLISH P2T Audio Input P2T AudioOutputs Connector Type XLR 1 4 inch combo Configuration electronically balanced Nominal Input Level 25 dBu 1 2 v
9. E e tr ere as oer erect erree tee aca errr errr tte 8 DE TR ss cx tras cer cna O 9 Wireless System SOLU P ita 9 Hybrid Wired Wireless System Set Drain 22 as aa le a in ahead 9 P2R Stand Alone Wired Setup 22 228 ed 9 SYSTEM APPLICATIONS TRRRRRROSBERRERRFRGEFEFPEFEFERPEFPFELGEEFEERERRFEFFFEFFREEEEFFETRRGEELTFEFFEBEFFEPDEREFEPFFEFBEFFFEFPRUEFPEEETEREEEFFFPELERFEFLEFEN 10 APPLICATION ONE Wireless Setup for a Vocalist cece cence erent ee eeeee ee eaeeeetaeeeeeeeeeeeaaeeeeeaaeeseeeeeesnaeeseenaeeseeeeesneeeeeaaes 10 APPLICATION TWO Combination Wired and Wireless Setup for a Drummer uunssesssensnenennnnnnnnnnnnnnnnnnennnnnn ernennen nenn 10 APPLICATION THREE Two PSM200 Wireless Systems Used Simultaneously uussssursnnenennnnnnnnnnnnnnnnnennnnnn ernennen nennen 11 RACK MOUNTING THE P2T nn sense neaeeaeeeseeeeee nen Ann nn seaeeaeeeseeaeeesseaseaaeeeseeseseeeeseaseeseeeeenees 11 TROUBLESHOOTING aiii seca seats oven cen nn ae Denn ne Da Anna eE aaa EEE aE 12 ACCESSORIES cia A Rise 12 SPECIFICATIONS Cidones 12 PSM200 Systeri ee A A A eee 12 a TransMIXER sree 2s a siria done 12 P2R Receiver aan RR end PR kein ae PERA dak ANNA RE RA NR eae 13 PSM200 Channel Frequencies eener eeaeee erea eei eee ARRE ana aaa LR nn ranma naanaas nenn 13 CERTIFICATIONS z 44 z 5424422 2000200002000 Bean ana idee anna Kann ana Fauna una Anno un devas svevscs decnantocaee cued FAKE EEE 14 PR SEEPS
10. HANNEL LED indicator begins to flash 2 When the LED indicator is flashing press the SELECT button to scroll to the desired frequency channel 3 Release the button After 4 seconds the display will stop flashing and the P2R will automatically switch to the specified channel N NOTE Set the P2R to the same channel as the P2T TransMixer Wired Mode When you are using the P2R Receiver as a stand alone wired monitor you can set the unit to wired mode This deactivates the RF circuitry and extends the battery life To Set the P2R to Wired Mode 1 Press and hold the SELECT button until the CHANNEL LED indicator begins to flash 2 When the LED indicator is flashing press the SELECT button to scroll past channel 8 until the letter A appears in the display 3 Release the button After 4 seconds the display will stop flashing and the P2R will automatically switch to wired mode N NOTE Setting the P2R receiver to wired mode disables its wireless capability Scanner Mode When you are using the P2R as a wireless receiver Shure recommends that during setup you first scan for a frequency channel that is free from interference 1 Unplug the P2T TransMixer and turn off the P2R 2 Hold down the P2R SELECT button while turning its volume knob past the click ON 3 Insert the earphones into your ears and slowly increase the P2R volume until you hear noise The CHANNEL LED will blink to confirm the unit is i
11. PREPELFEFFGEFITEEBERFTEFPERLERPEUFTUAOREETFERTEIEREERECRARHFRTHURZTHETSSLEHRERETLUTTESTETTEFERLERLEUSBRRBETEFHERATBERSPFCERFERFTREFEr 14 PZR Receiver MIX IN Jack Wiring Diagram s sinais na anni o as 14 ENGLISH QUICK SETUP GUIDES PSM 200 Wireless System The following set up illustration is for the complete PSM200 Wireless System which includes the P2T TransMixer the P2R Receiver and the SCL2 Earphones If you have purchased the P2R as a stand alone wired personal monitor see page 4 1 Plug in the power supply and connect it to the DC 2 Insert a 9 Volt battery into the P2R Receiver input on the rear panel of the P2T TransMixer observing proper polarity Mixing Console ddtdittititi TW 3 Connect audio sources to the MIC LINE INPUTS on the front 6 Check the RF LED on the top of the Receiver to panel of the TransMixer confirm that it is receiving signal from the TransMixer 4 Turn the Receiver volume knob clockwise past the click ON 7 Plug the Earphones into the earphone jack on the Keep the volume at a low setting Receiver Insert the Earphones into your ears 5 Set the TransMixer and Receiver to the same frequency chan 8 Increase Receiver volume until the knob is turned to nel See the Selecting a Frequency Channel section on page 6 approximately 11 o clock Mixing Console diddfitiiii ta 9 On the front panel of the Tra
12. al device pursuant to part15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruc tions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help 90 DECLARATION OF CONFORMITY Shure Incorporated 5800 Touhy Ave Niles Illinois 60714 U S A 847 600 2000 declare under our sole responsibility that the following product Model P2R Name UHF Wireless Microphone Receiver was tested and found to comply with Part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not caus harmful interference and 2 this device must accept any interference received in interference that may cause
13. ated Europe Middle East Africa Shure Europe GmbH Wannen ckestr 28 74078 Heilbronn Germany Phone 49 7131 72140 Fax 49 7131 721414 Email info shure de Asia Pacific Shure Asia Limited Unit 301 3rd Floor Citicorp Centre 18 Whitfield Road Causeway Bay Hong Kong Phone 852 2893 4290 Fax 852 2893 4055 Email info shure com hk Canada Latin America Caribbean Shure Incorporated 5800 West Touhy Avenue Niles IL 60714 4608 USA Phone 847 600 2000 Fax 847 600 6446 Email international shure com
14. d Mix Mixing Console ddidiittiin TH APPLICATION TWO Combination Wired and Wireless Setup for a Drummer The following application uses the P2R as a combination wired wireless Receiver The MIX IN jack of the P2R is connected to a click track for the drummer 1 Connect the drum mix out of the Mixing Console to INPUT 1 of the P2T TransMixer Connect the band mix out of the Mixing Console to INPUT 2 of the P2T Set the P2T and the P2R to the same frequency channel Insert the SCL2 earphones into your ears and adjust the mix of INPUT 1 and INPUT 2 on the TransMixer Set the P2R Receiver to a comfortable level Set the GAIN switch on the P2R to LO Connect the Click Output to the MIX IN 1 4 inch jack of the P2R and adjust your levels NO GP ON Track 10 ENGLISH APPLICATION THREE Two PSM200 Wireless Systems Used Simultaneously The following configuration uses two PSM200 systems simultaneously and utilizes the SPLIT OUT feature of the TransMixer In this example the musicians keep the TransMixers on stage with them in order to control their personal mixes independent of the house engineer 1 Connect the vocal mic to INPUT 1 of the Vocal Mix TransMixer and connect SPLIT OUT 1 the vocals to the Mixing Console 2 Connect the total band mix from the Mixing Console to INPUT 2 of the Vocal Mix TransMixer NOTE In this example the band mix includes vocals This allows the guitar mix to include vocals and allows the vocal
15. ery life To view the frequency channel when the LED indicator is off simply press and release the SELECT button Battery Installation 1 Unlock the battery compartment door by pressing down on the side of the battery compartment door marked OPEN and sliding it in the direction of the arrow 2 Flip open the door and insert a fresh 9V alkaline battery observing proper polarity 3 Flip the battery compartment door closed then press and slide the compartment door until it snaps shut Note If the battery compartment door will not close completely the battery is not correctly inserted Since the average life of a battery varies depending on the manufacturer Shure recommends that youuse a fresh 9V battery for performances longer than two hours You can then reserve used batteries for rehearsals or other less critical applications Cable Management Groove 1 Connect an audio source to the 1 4 inch MIX IN jack on the side of the P2R 2 Attach the P2R to your belt waist band or another location 3 Slide the audio cable or earphone cord up into the groove as illustrated 4 The belt clip will hold them securely in place ENGLISH Wireless Mode When you are using the P2R as a wireless receiver or as a combination wired and wireless receiver use the SELECT button on the side of the P2R Receiver to set the frequency channel 1 8 To Select a Frequency Channel 1 Press and hold the SELECT button until the C
16. fects processors pre amp outputs from guitar or bass amps or line outputs from mixing consoles When used with a mono connector the ring of the MIX IN jack is grounded This doesn t harm the P2R ENGLISH 14 PS20 Conforms to applicable U S and Canadian electrical and safety standards PS20E PS20UK Conforms to European low voltage directive 72 23 EEC Eligible to bear CE marking SHURE P2R Tested To Comply C With FCC Standards FOR HOME OR OFFICE USE The term IC before the radio certification number only signifies that Industry Canada technical specifications were met 5 V BIAS SLEEVE RING PRE AMP E gt TIP 1 MEG OHM AIGAIN LO DECLARATION OF CONFORMITY We of Shure Incorporated 5800 Touhy Ave Niles Illinois 60714 U S A 847 600 2000 declare under our sole responsibility that the following product Model P2R Name UHF Wireless Microphone Receiver was tested and found to comply with Part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Shure Inc Manufacturer Signed La 4 A a Date MALH J 2007 Name Title Craig Kozokar EMC Project Engineer Global Compliance Shure Inc Note This equipment has been tested and found to comply with the limits for a Class B digit
17. icate low battery When this LED starts nel or set to A for wired mode blinking you have approximately 15 minutes of battery 8 MIX IN Jack Connect a 1 4 inch line level input to this time remaining depending on volume level and battery jack Use alone or in combination with wireless reception brand from the P2T TransMixer See the MIX IN Jack section on 2 On Off Volume Knob Turn clockwise past click to page 8 for details power on Continue to turn clockwise to increase volume 9 GAIN Switch Slide to HI or LO position to set the sensi counterclockwise to decrease volume tivity of the MIX IN input 3 LIM LED Lights only when limiter is activated See the 10 Earphone Output Jack Connect SCL2 earphones to this LIM LED section on page 8 for details 1 8 inch 3 5mm jack 4 RF LED Lights when the unit is receiving radio 11 Cable Management Groove For a secure connection frequency RF signal from the P2T TransMixer guide the cable connected to the MIX IN Jack or the ear 5 Antenna An attached flexible whip antenna receives RF phone cord into this groove signal from the TransMixer 12 Belt Clip Securely attaches the unit to a belt guitar strap 6 CHANNEL LED Indicator Displays the number of the or waist band current frequency channel 1 8 or the letter A for wired 13 Battery Compartment Door See the Battery Installation mode The CHANNEL LED indicator shuts itself off after section below 10 seconds to conserve batt
18. inisterial license to operate this equipment may be required in certain areas Consult your national authority for pos sible requirements ENGLISH TABLE OF CONTENTS QUICK SETUP GUIDES lt lt lt as 3 PSM 200 Wireless SysteM ae ae hl Ask ann asa aa pa 3 PR2 Receive Quick Setup GUIAS cts 4 INTRODUCTION sssss cuasssssosmessissassconiaaiasesires debatececncccnees end secvacssadeccteveetenecdis shecatseeeseeseinavaces raiadas UPANA Eanan rania 5 The PSM200 Persomal Monitor Systemi ssse cas ces eaii ai i a A teased sia akt 5 CELUI S se ses Sex daa ANPR ADA REAR RREO a eden eats ace acces ieee RR A 5 THE P21 TRANS MIXER cicis rainane innata AR AA AAA 6 Controls and Feature Screan e Ae 6 Audio INPUTS and QuUipuiS cit A ia A eE EEE E E 6 Phantom POE r E oia 6 Selecting a Frequency Channel 0 ccccccccecsssscesecesesssaeececseseaesecencsesesececeseseeaeesececesaesesescsuseeesesssusssesesscaeseaecesesesasaeeeeescaaeaesesees 6 li A O O O 7 Controls and Features outra a iaa di izo ld E 7 Battery Instalan a ads 7 Cable Management Groove cirio aaa ic 7 A Tas cisto jo co RD RE RR en IATE DRE RR SERRO RR q RR 8 Wired Mode ea lh de ed a nb ee ete eek ae ee abra 8 Scanner Modera Aare case eect swe cece cortando aci n io wt satire ooo GARD a PESAR DEC erat LEO pa DE nooo Nas SENDA faa podio DANOS ease E TESES 8 MIX IN Da Ck RSRS O RR ete gO ERR RENAS encod RARE DAR RAR 8 LME E ODE ere reer re ter er os eet ado ORDER GAM
19. ist to independently control more of the vocal level in his her personal mix Set the Vocal Mix P2T and P2R Receiver to the same frequency channel Connect SPLIT OUT 2 of the Vocal Mix TransMixer the band mix to INPUT 1 of the Guitar Mix TransMixer Connect the guitar amp simulator to INPUT 2 of the Guitar Mix P2T TransMixer Connect the SPLIT OUT 2 of the Guitar Mix TransMixer the guitar amp simulator to the Mixing Console Set the Guitar Mix P2T TransMixer and P2R Receiver to a frequency channel that s different from the channel you set for the Vocal Mix system in step 3 NS a Ryo Up to four systems can be used at the same time Vocal Mic Band Mix SPLIT OUT SPLIT OUT fromTransMixer from TransMixer Y V Guitar Amp Simulator Mixing Console N OUT TransMixer ddidiitititi HRA RACK MOUNTING THE P2T The P2T features a standard 1 2 rack space design and includes a rack mounting kit N WARNING Do not torque the screws too tightly or the chassis may be damaged Install Rack Ears Single Unit Dual Mounting Two Units j A Fl re Ae ADOOS l Mount in an Equipment Rack u io A o EIN Te ig E aN EN a p ada g MA NOTE Be sure to use both straddle bars when installing dual uni
20. n Scanner Mode N WARNING Increase the volume slowly as the noise may be loud 4 Scroll through the eight available frequencies to locate a clear channel A channel is clear if you hear uninterrupted whitenoise from the P2R Avoid channels that have no sound This indicates interference on that frequency channel which makes it unsuit able for use 5 To exit scanner mode simply turn off the P2R When you turn the unit back on it will be set to the channel that you last selected 6 Setthe P2T to the same channel as the P2R MIX IN Jack When you are using the P2R Receiver as a stand alone personal monitor the 1 4 inch MIX IN jack serves as the primary audio input In addition the MIX IN jack allows the P2R to function as a hybrid wired and wireless receiver When you are using the P2R in its wireless mode you can add a second audio source via the MIX IN jack such as e Click Tracks e Pre Amp Outputs from Guitar or Bass e Effects Processors e Condenser Microphones Next to the jack is a two position GAIN switch that gives you a choice between LO and HI gain settings for the input For specific infor mation on how the MIX IN jack functions refer to the wiring diagram on page 14 LIM LED The P2R Receiver has a non defeatable constantly active limiter that automatically activates if the receiver output level exceeds a certain volume which is calibrated specifically for the Shure SCL2 earphones The LIM LED on the top of
21. nsMixer adjust the signal level of each audio input with the INPUT knobs 10 Check the INPUT LEDs on the TransMixer to verify that signal is present but not clipping See the Audio Inputs and Outputs section on page 6 for details 11 Slowly adjust the Receiver volume to a comfortable level PR2 Receiver Quick SetUp Guide ENGLISH When Used as a Wired Stand Alone Personal Monitor 1 Inserta 9 Volt battery into the P2R Receiver observing proper polarity Mixing Console ddiditiitiii Wh 2 Connect an audio source to the 1 4 inch MIX IN jack on the side of the P2R 3 Turn the P2R volume knob on past the click Keep the volume at a low setting CHANNEL SELECT O Ne 4 Set the CHANNEL to A with the SELECT Button See the Wired Mode section on page 8 for details 5 Set the GAIN switch to LO initially and set your source volume to a moderate level 6 Attach the P2R onto your belt waistband or another location and slide the cable into the cable management groove on the back side of the unit 7 Plug Earphones into the earphone jack on the P2R Insert the Earphones into your ears 8 Slowly adjust the volume to a comfortable level Set the GAIN switch to HIGH if the signal level is too low INTRODUCTION ENGLISH Thank you for buying the PSM200 Like all Shure PSM personal monitoring products the PSM200 provides the
22. ole ddidiftitiii TW 5 Attach the P2R onto your belt waistband or another location 6 Slide the audio cable or earphone cord into the cable management groove 7 Plug the earphones into the earphone output jack Insert the earphones into your ears as instructed in the ear phone user s guide 8 Slowly increase the P2R volume to a comfortable level Set the GAIN switch to HI if you need more level AN NOTE Setting the P2R receiver to A disables its wireless capability and extends the battery life If you have purchased the P2R as a stand alone personal monitor you can go wireless by simply purchasing a P2T TransMixer ENGLISH SYSTEM APPLICATIONS This section presents three typical applications for the PSM200 For more ideas visit Shure s website at www shure com APPLICATION ONE Wireless Setup for a Vocalist This is the basic wireless configuration of the PSM200 system for a single user either instrumental or vocal 1 Connect the vocal mic to INPUT 1 of the P2T TransMixer Connect SPLIT OUT 1 from the P2T to the Mixing Console Connect the instrumental mix line out to INPUT 2 of the P2T Set the P2T and P2R to the same frequency channel Insert the SCL2 earphones into your ears and adjust the mix of INPUT 1 and INPUT 2 on the TransMixer OP ON Sects a Wireless Su Transmission N q Be N L N Vocal Mic Signal SPLITOUT from TransMixer Vocal Mic Ban
23. olume 12 o clock Passive connection parallel with input Connector Type XLR Configuration electronically balanced Pin Assignments 2 hot 3 cold 1 ground Phantom Power Protection Yes Up to 52 Vdc Maximum Input Level 5 dBu 1 2 volume Power Requirements 12 o clock Operating voltage 12 18 Vdc Pin Assignments XLR 2 hot 3 cold 1 ground g g 1 4 Tip hot Ring cold Supplied with one of the following external power supplies Sleeve ground Model PS20 120 VAC 60Hz input Model PS20E Model PS20UK 230 VAC 50 60Hz input Model PS20AR 220 VAC 50Hz input P2R Receiver Power Requirements RF Sensitivity 9 V alkaline battery recommended 109dBm typical Battery Life Squelch Threshold Volume Dependent 102dBm typical Wed RF OF Antenna Attached Whip Audio Input Connector Audio Output Connector Connector Type aa Connector Type 1 4 inch Mono na id E Minimum Load Impedance 50 Maximum Input Level LO 0 dBu 100 g 3 520z less battery Frequency Response 30 Hz to 20k Hz 3dB a 122 mm x 73 mm x 32 mm 4 809 in x2 875 in x1 251in PSM200Channel Frequencies The PSM200 is available in four frequency groups each coordinated to work in a specific geographic region You can find the fre quency group for your system printed on the rear panel of the P2T TransMixer For more information on which frequencies can be used in your area call our Applications Group at 847 600
24. page 6 for details user s guide IMPORTANT Never set more than ONE TransMix 10 Slowly increase the P2R volume to a comfortable level er to the same frequency channel or interference will occur 4 Observe the signal clip LEDs If they are consistently red decrease the level with the corresponding INPUT level knob Mixing Console ddidiitiiiit MA Hybrid Wired Wireless System Setup To configure the P2T TransMixer and P2R Receiver for hybrid wired wireless operation Follow steps 1 9 of the Wireless System Set Up section Connect an audio source to the 1 4 inch MIX IN jack on the side of the P2R Set the GAIN switch to LO initially and set the source volume to a moderate level Attach the P2R onto your belt waistband or another location arp on gt Slide the audio cable or earphone cord into the cable management groove 6 Slowly increase the P2R volume to a comfortable level Set the GAIN switch to HI if you need more level P2R Stand Alone Wired Set Up To configure the P2R Receiver as a stand alone personal monitor 1 Turn the On Off Volume knob clockwise past click On Leave the vol ume setting low 2 Set the CHANNEL to A with the SELECT Button See the Wired Mode section on page 8 for details 3 Connect an audio source to the 1 4 inch MIX IN jack on the side of the P2R 4 Set the GAIN switch to LO initially and set the source volume to a moderate level Mixing Cons
25. plit output level INPUT LED RED Limited Signal YELLOW Nominal Level O GREEN Signal Present A o Microphone Level Line Level Input Knob Although the TransMixer itself does not provide phantom power for condenser microphones the SPLIT OUT connectors pass phan tom power from a phantom power supply to a microphone connected to the corresponding input jack You can connect equipment that supplies phantom power to the TransMixer without harming the unit CAUTION Use a direct box when connecting guitars keyboards and other instruments to a mixing console through the P2T The phantom power that mixing consoles provide for microphones can damage other instruments Connect the instru ment to the direct box then connect the direct box to the TransMixer input Selecting a Frequency Channel 1 Press and hold the SELECT button until the CHANNEL LED indicator begins to flash 2 When the LED indicator is flashing press the SELECT button to scroll to the desired frequency channel 3 Release the button After 4 seconds the display will stop flashing and the P2T will automatically switch to the specified channel IMPORTANT Never set more than ONE TransMixer to the same frequency channel or interference will occur ENGLISH P2R RECEIVER Controls and Features 1 POWER LED Lights to indicate the unit is powered on 7 SELECT Button Press to increment the frequency chan and blinks to ind
26. the unit lights up when the limiter is on If the LIM LED blinks occasionally turn down the volume of the receiver If the LED is on and you haven t reached a high enough listening level try re inserting the earphones for a better seal or adjust the mix that is being sent to the receiver to include only the most essential inputs When the LED is on the volume will not increase The limiter is designed to work best with the Shure SCL2 earphones Using the P2R with other Shure earphones or earphones made by other manufacturers can result in higher limited volume levels ENGLISH SETUP 5 To pass audio signal directly through the TransMixer use the corresponding SPLIT OUT connector on the rear Wireless System Setup panel of the device To configure the P2T TransMixer and P2R Receiver for wireless 6 Turn the On Off Volume knob on the P2R clockwise past operation click On Leave the volume setting low 1 Plug the power supply into the DC INPUT connector on 7 Set the P2R to the same frequency channel as the P2T the rear panel of the P2T then plug it into a power outlet Check the RF LED on the P2R to confirm that transmis 2 Connect audio sources to the combo XLR 1 4 inch jacks sion is being received nieta panel 9 Plug earphones into the earphone output jack Insert the 3 Selecta frequency channel 1 8 See the Selecting a Fre earphones into your ears as instructed in the earphone quency Channel section on
27. ts 11 TROUBLESHOOTING ENGLISH PROBLEM SOLUTION No sound at the receiver Y Check the power cord on the TransMixer and make sure it is powered on Make sure both the TransMixer and the P2R Receiver are set to the same frequency channel Make sure the earphones are plugged in to the receiver and the volume is up Make sure the Receiver is on and the battery is good Check the incoming audio connections on the TransMixer Low receiver range Try to maintain line of sight between the TransMixer and Receiver antennas q Try another frequency in case interference is limiting the range Y Check for television channel interference More information is available at www shure com Receiver sounds fuzzy or distorted Make sure no other TransMixers or wireless transmitters are operating on your frequency Y Make sure the TransMixer input level is lighting yellow LEDs for optimum performance Make sure you are using a fresh battery in the P2R Low audio output at the receiver V Make sure the TransMixer input level is lighting yellow LEDs for optimum performance Make sure the P2R Receiver s volume knob is up ACCESSORIES Furnished Accessories P2T TransMixer AC Adaptor eee PS20 PS20E PS20UK PS20AR Single Mount Rack Bracket issnin 53A8484 Dual Mount Rack Bracket o oooocccccncccnccccoccnonocinananonnns 53B8484 Straddle Bars 53A8443 H rdwareKit einen entre 90AD8100 SPECIFI
Download Pdf Manuals
Related Search