Operating Instructions - VEGADIS 11
Contents
1. see chapter Connecting to power supply and tighten the cable gland 4 2 Mounting instructions VEGADIS 11 can be mounted as follows e on carrier rail 35 x 7 5 according to EN 50022 e on mounting plate or on the wall VEGADIS 11 e L080t L N3 8886L 19888 EN 140801 VEGA 5 Connecting to power supply Note safety instructions Take note of safety instructions for Ex applications Select connection cable Select connection ED cable for Ex applica tions Cable screening and grounding Cable screen and ground ing for Ex applications 5 Connecting to power supply 5 1 Preparing the connection Always keep in mind the following safety instructions e Connect only in the complete absence of line voltage In hazardous areas you must take note of the respective regulations conformity and type approval certificates of the sensors and power supply units The instrument is connected with standard two wire cable without screen If electromagnetic interference is expected which is above the test values of EN 61326 for industrial areas screened cable should be used Use cable with round cross section A cable outer diameter of 5 9 mm 0 2 0 35 in ensures the seal effect of the cable gland If you are using cable with a different diameter or cross section exchange the seal or use a suitable cable gland Take note of the corresponding installation regulations for Ex applica tions If screened cable is2. IIC T6 D The indication remains dark if the loop current is not sufficient for operation 2 Deviating data in Ex applications see separate safety instructions VEGADIS 11 e 17 9 Supplement 9 2 Dimensions VEGADIS 11 38mm 82mm 8 15 64 IOS ANI a SS VEAL 9 bs VEGA a Z2 e S P d D E im st ZR o rn E GES EE oO T e i M20x1 5 Fig 8 VEGADIS 11 size of digits VV x H approx 5 x 9 mm 18 VEGADIS 11 e L080t L N3 8886L 19888 EN 140801 VELA 9 Supplement 9 3 Industrial property rights VEGA product lines are global protected by industrial property rights Further information see WWW Vega com Only in U S A Further information see patent label at the sensor housing VEGA Produktfamilien sind weltweit gesch tzt durch gewerbliche Schutzrechte N here Informationen unter www vega com Les lignes de produits VEGA sont globalement prot g es par des droits de propri t intellec tuelle Pour plus d informations on pourra se r f rer au site www vega com VEGA lineas de productos est n protegidas por los derechos en el campo de la propiedad indus trial Para mayor informaci n revise la pagina web www vega com Jluuna npogykynn Qupmbi BETA 3auujarorcs no BceMy Mupy npaBaMM Ha MHTeTITIEKTyaTIBHylO co6crBeHHOCTb JanbHeliwyto uHcbopmaunuto cvorpure Ha calire www vega com VEGAJXK
3. JI MELREA UR RF o 3t 3 fe amp iB 2 A Y lt www vega com 9 4 Trademark All the brands as well as trade and company names used are property of their lawful proprietor originator VEGADIS 11 e 19 Printing date VELA All statements concerning scope of delivery application practical use and operat ing conditions of the sensors and processing systems correspond to the information available at the time of printing Subject to change without prior notice C 19888 EN 140801 VEGA Grieshaber KG Schiltach Germany 2014 VEGA Grieshaber KG Phone 49 7836 50 0 Am Hohenstein 113 Fax 49 7836 50 201 77761 Schiltach E mail info de vega com Germany www vega com
4. call back for needed information If a repair is necessary please proceed as follows Print and fill out one form per instrument Clean the instrument and pack it damage proof Attach the completed form and if need be also a safety data sheet outside on the packaging Please contact the agency serving you to get the address for the return shipment You can find the agency on our home page www vega com VEGADIS 11 e 15 8 Dismount 8 Dismount 8 1 Dismounting steps Warning Before dismounting be aware of dangerous process conditions such as e g pressure in the vessel or pipeline high temperatures cor rosive or toxic products etc Take note of chapters Mounting and Connecting to power supply and carry out the listed steps in reverse order 8 2 Disposal The instrument consists of materials which can be recycled by spe cialised recycling companies We use recyclable materials and have designed the parts to be easily separable WEEE directive 2002 96 EG This instrument is not subject to the WEEE directive 2002 96 EG and the respective national laws Pass the instrument directly on to a spe cialised recycling company and do not use the municipal collecting points These may be used only for privately used products according to the WEEE directive Correct disposal avoids negative effects on humans and the environ ment and ensures recycling of useful raw materials Materials see chapter Technical
5. requested value e g O with the and keys Final value Set the rotary switch to span Set the requested value e g 1000 with the and keys Decimal point Set the rotary switch to point With the and keys you can adjust the requested value e g 8888 no decimal point Set rotary switch to OPERATE Screw the housing cover back on The adjustment data are effective the output current 4 20 mA cor responds to the actual level VEGADIS 11 e 13 7 Maintenance and fault rectification VEGA Reaction when malfunc tions occur Causes of malfunction 24 hour service hotline Check the 4 20 mA signal 9 Reaction after fault recti fication 7 Maintenance and fault rectification 7 1 Maintenance If the instrument is used properly no special maintenance is required in normal operation 7 2 Rectify faults The operator of the system is responsible for taking suitable meas ures to rectify faults VEGADIS 11 offers maximum reliability Nevertheless faults can oc cur during operation These may be caused by the following e g e Sensor e Process e Voltage supply e Signal processing Should these measures not be successful please call in urgent cases the VEGA service hotline under the phone no 49 1805 858550 The hotline is manned 7 days a week round the clock Since we offer this service worldwide the support is only available in the English language T
6. 42 Mou nting instr ctiOriS i iiid DE rere toe bebe ct esed ore oet l Gehe ce said ant 8 Connecting to power supply 5 41 Preparirigithe COhnectlOl uice eminent epe cte rh Fre seinen Er REOR EE ee eie aee 9 5 2 Connection DrOCedUle 2 retenti ree een ci e E Pe ED e tanita 9 5 39 WiNA Pla eses E etree rr 10 Setup 6 1 Adjustmoerit SySUeIm aou iere tere t ed rrt e id vd edd te n dovere pa 11 6 2 Indicationscalltig iit tete t tt sere en t een t Ls recae 11 Maintenance and fault rectification Ze Maintenance tena bua cu ee Ena DERE EET ELERET HE GRERAXEE EXP ATENE E Soi DR ES F tevectsdbacuarances 14 4 2 BectilyTaultS Ete eie ecce EE ERI Rocco petas io IH eR oRUe es e AR Gd 14 7 3 How to proceed if a repair is needed eese ener nne etit 15 Dismount 8 1 Dismounting steps eene ene nen nnne enn nennen nene en enis ener nennen nen 16 8 2 Disposal os C EI EH Ta ai dal ria Pa a 16 Supplement 9 1 Technical data t nir no i n rer per ss 17 9 2 Dimensions rnm eir ra nen ndn cr i st Era sir ran 18 VEGADIS 11 e L080t L N3 8886L 19888 EN 140801 1 About this document E O P BB me 1 About this document 1 1 Function This operating instructions manual provides all the information you need for mounting connection and setup as well as important instruc tions for maintenance and fault rectification Please read this informa tion before
7. Operating Instructions VEGADIS 11 il Document ID 19888 Contents VELA Contents 1 About this document Tet CPUDCHOD oiii iei einreichen Ice a arere he Der is err reae ENE a 3 r WaAlQCt QrOUp ies 3 T 3 Symbols used iiber ee Hsec red e a ade idle en dears 3 For your safety 25 Authorised persotlniel 2 rrt eines censentur etna ee essent Dee eene eap aeniea erue s RIEN UO 2 2 Appropriate lise insit atentament meten te festes tus et ant estima 2 3 Warning about incorrect use 24 General Safety instructions tette terree Yee ea ER EX ERE Pee NE itat tasses setavvieesstereasevciess 2 5 Safety label on the instrument visiis ssccscessiscecsssssessaeseessocssssessseconceustesssisessessanssvseesstessaeesstees 4 2 6 CE conformity 2 7 Safety instructions for Ex areas sssssssssssssssseseee eene errem nennen 5 2 8 Environmental instr ctloris 5 ooo eee deity ee aeta ceo Fra eee Eau E sem FREE EE DERE Ea esa Gives 5 Product description 3 1 GConfiguration es ceret erret ttn oat ee tatio eee mm REP RARE ERR ente ko EARR e eee ip rand uus 6 3 2 Principle of operation ssssssssesssssseeeeeeeeneneeen nnne nnn nnne nee nenne ennn nein nennen 6 3 3 Operation 3 4 Packaging transport and storage ssssssssssssseeee eene enne nennen 7 Mounting 44 Gereralinstr ctions oie aei e neben ed tea aei o E il dled 8
8. data If you have no way to dispose of the old instrument properly please contact us concerning return and disposal 16 VEGADIS 11 e L080t L N3 8886L 19888 EN 140801 VELA 9 Supplement 9 Supplement 9 1 Technical data General data 316L corresponds to 1 4404 or 1 4435 316Ti corresponds to 1 4571 Materials Housing Ground terminal Inspection window of the indication Weight plastic PBT 316Ti 316L approx 0 5 kg 1 102 Ibs Ambient conditions 20 70 C 40 158 F Ambient temperature Storage and transport temperature 40 85 C 40 185 F Electromechanical data Cable gland 2 x cable entry M20 x 1 5 cable 5 9 mm Screw terminals for cable cross section up to 2 5 mm AWG 14 Adjustment and display elements Adjustment elements Indication Measured value indication Number of figures digital value Size of digits Number of segments bar graph 2 keys 1 rotary switch LC multiple function display with bar graph digital value 4 digit and tendency indicator for rising or falling values 4 WxH 5 5x10mm 20 Voltage supply Voltage supply Max input current Voltage loss with 20 mA Current range via the signal circuit 150 mA approx 4 5 V 3 5 22 5 mA Electrical protective measures Protection rating Overvoltage category Protection class IP 66 IH IH Approvals ATEX ia ATEX Il 2G EEx ia
9. dle normal loads during transport is assured by a test based on ISO 4180 The packaging of standard instruments consists of environment friendly recyclable cardboard For special versions PE foam or PE foil is also used Dispose of the packaging material via specialised recycling companies Transport must be carried out in due consideration of the notes on the transport packaging Nonobservance of these instructions can cause damage to the device The delivery must be checked for completeness and possible transit damage immediately at receipt Ascertained transit damage or con cealed defects must be appropriately dealt with Up to the time of installation the packages must be left closed and stored according to the orientation and storage markings on the outside Unless otherwise indicated the packages must be stored only under the following conditions e Notin the open Dry and dust free Not exposed to corrosive media Protected against solar radiation Avoiding mechanical shock and vibration Storage and transport temperature see chapter Supplement Technical data Ambient conditions e Relative humidity 20 85 VEGADIS 11 e 4 Mounting VEGA Installation position Moisture Mounting versions 4 Mounting 4 1 General instructions VEGADIS 11 can be mounted in any position However vertical mounting is recommended By doing so penetration of moisture can be avoided Use the recommended cables
10. ecification low impedance 11 Tighten the compression nut of the cable entry gland The seal ring must completely encircle the cable 12 Screw the housing cover back on The electrical connection is finished 5 3 Wiring plan Fig 2 Wiring plan passive sensor 1 To the sensor 2 For voltage supply or to the processing system active input 3 forindication 4 Control instrument 4 20 mA measurement Fig 3 Wiring plan active sensor 1 To the sensor or to the signal conditioning instrument 2 for indication 3 To the processing system passive input 10 VEGADIS 11 e L0807L N1 88861L 19888 EN 140801 VEGA 6 Setup 6 Setup 6 1 Adjustment system Adjustment elements TRANSMITTER DISPLAY IES A No vem P Fig 4 Adjustment elements of VEGADIS 11 1 2 3 Adjustment volume Adjustment system e e Rotary switch choose the requested function key change value rising key change value falling operate operation zero adjustment of the min value 4 mA span adjustment of the max value 20 mA point shifting of the decimal point The desired function is selected with the rotary switch With the and keys the signal current or the integration time is set or the indication is scaled The respective rotary switch is finally set to position OPERATE The set values are transmitted to
11. he service is free only standard call charges are incurred Connect a multimeter in the suitable measuring range according to the wiring plan Error code Cause Rectification 4 20mA Level fluctuations Adjust integration time via PACTware Sma not No atmospheric pres Check pressure compensation sure compensation with pressure trans mitters 4 20mA Wrong connection to Check connection according to signal miss voltage supply chapter Connection steps and ing if necessary correct according to chapter Wiring plan No power supply Check cables for breaks repair if necessary Operating voltage Check adapt if necessary too low or load resist ance too high Current sig Electronics module in Exchange the instrument or send it nal 3 6 mA the sensor defective in for repair 22 mA In Ex applications the regulations for the wiring of intrinsically safe circuits must be observed Depending on the reason for the fault and the measures taken the steps described in chapter Set up may have to be carried out again 14 VEGADIS 11 e L080t L N3 8886L 19888 EN 140801 7 Maintenance and fault rectification 7 3 How to proceed if a repair is needed You can find a repair form as well as detailed information on how to proceed at www vega com downloads and Forms and certificates By doing this you help us carry out the repair quickly and without hav ing to
12. ist personnel authorised by the plant operator During work on and with the device the required personal protective equipment must always be worn 2 2 Appropriate use VEGADIS 11 is a digital indicating instrument for 4 20 mA circuits 2 3 Warning about incorrect use Inappropriate or incorrect use of the instrument can give rise to application specific hazards e g vessel overfill or damage to system components through incorrect mounting or adjustment 2 4 General safety instructions This is a state of the art instrument complying with all prevailing regulations and guidelines The instrument must only be operated in a technically flawless and reliable condition The operator is responsible for the trouble free operation of the instrument During the entire duration of use the user is obliged to determine the compliance of the necessary occupational safety measures with the current valid rules and regulations and also take note of new regula tions The safety instructions in this operating instructions manual the na tional installation standards as well as the valid safety regulations and accident prevention rules must be observed by the user For safety and warranty reasons any invasive work on the device beyond that described in the operating instructions manual may be carried out only by personnel authorised by the manufacturer Arbi trary conversions or modifications are explicitly forbidden The safety approval marking
13. ivery encompasses e Digital indicating instrument VEGADIS 11 e Documentation this operating instructions manual Ex specific safety instructions with Ex versions if necessary further certificates The VEGADIS 11 consists of the components e Housing with integrated adjustment insert e Housing cover with integrated indicating module Fig 1 VEGADIS 11 1 Adjustment insert 2 Indication 3 Cover 4 Housing 3 2 Principle of operation VEGADIS 11 is a digital indicating instrument for measured value indication in 4 20 mA circuits The measured value is displayed digitally or as bargraph via the LC display The digital indication can be scaled VEGADIS 11 is suitable for wall and carrier rail mounting VEGADIS 11 is looped directly into the 4 20 mA circuits and requires no separate external energy Connection is carried out via screw terminals in the housing 3 3 Operation For scaling the indication VEGADIS 11 is equipped with an adjust ment module Adjustment is carried out via a rotary switch and two keys VEGADIS 11 e L080t L N3 8886L 19888 EN 140801 VEGA 3 Product description Packaging Transport Transport inspection Storage Storage and transport temperature 3 4 Packaging transport and storage Your instrument was protected by packaging during transport Its capacity to han
14. putting the instrument into operation and keep this manual accessible in the immediate vicinity of the device 1 2 Target group This operating instructions manual is directed to trained specialist personnel The contents of this manual should be made available to these personnel and put into practice by them 1 3 Symbols used Information tip note This symbol indicates helpful additional information Caution If this warning is ignored faults or malfunctions can result Warning If this warning is ignored injury to persons and or serious damage to the instrument can result Danger If this warning is ignored serious injury to persons and or destruction of the instrument can result Ex applications This symbol indicates special instructions for Ex applications SIL applications This symbol indicates instructions for functional safety which must be taken into account particularly for safety relevant applications List The dot set in front indicates a list with no implied sequence Action This arrow indicates a single action Sequence of actions Numbers set in front indicate successive steps in a procedure Battery disposal This symbol indicates special information about the disposal of bat teries and accumulators VEGADIS 11 e 2 For your safety VEGA 2 For your safety 2 1 Authorised personnel All operations described in this operating instructions manual must be carried out only by trained special
15. required connect the cable screen on both ends to ground potential In the VEGADIS 11 the screen must be connect ed directly to the internal ground terminal The ground terminal on the outside of the housing must be connected to the potential equalisa tion low impedance If potential equalisation currents are expected the connection on the processing side must be made via a ceramic capacitor e g 1 nF 1500 V The low frequency potential equalisation currents are thus suppressed but the protective effect against high frequency interfer ence signals remains In Ex applications one sided grounding on the sensor is recommend ed see EN 60079 14 5 2 Connection procedure Proceed as follows 1 Unscrew the housing cover 2 Loosen compression nut of the cable entry gland 3 Remove approx 10 cm of the cable mantle strip approx 1 cm insulation from the individual wires 4 Insert the cable into VEGADIS 11 through the cable entry 5 Loosen the screwed terminals with a screwdriver 6 Insert the wire ends into the open terminals according to the wir ing plan 7 Tighten screw terminals again 8 Check the hold of the wires in the terminals by lightly pulling on them VEGADIS 11 e 5 Connecting to power supply VEGA Passive sensors Active sensors sensors with signal conditioning instrument 9 Connect the screen to the ground terminal 10 Connect the ground terminal outside on the housing according to sp
16. s and safety tips on the device must also be observed 2 5 Safety label on the instrument The safety approval markings and safety tips on the device must be observed 2 6 CEconformity The instrument is CE conform to EMVG 89 336 EWG NSR 73 23 EVVG and corresponds to NAMUR recommendation NE 21 Conformity has been judged according to the following standards e EMC Emission EN 50081 1 Susceptibility EN 50082 2 VEGADIS 11 e L080t L N3 88861 19888 EN 140801 2 For your safety e LVD EN 61010 1 2 7 Safety instructions for Ex areas Please note the Ex specific safety information for installation and op eration in Ex areas These safety instructions are part of the operating instructions manual and come with the Ex approved instruments 2 8 Environmental instructions Protection of the environment is one of our most important duties That is why we have introduced an environment management system with the goal of continuously improving company environmental pro tection The environment management system is certified according to DIN EN ISO 14001 Please help us fulfill this obligation by observing the environmental instructions in this manual e Chapter Packaging transport and storage e Chapter Disposal VEGADIS 11 e 3 Product description Scope of delivery Constituent parts Area of application Voltage supply 3 Product description 3 4 Configuration The scope of del
17. the EEPROM memory and remain there even in case of voltage loss 6 2 Indication scaling Preparation For scaling the indication it is recommended to screw the housing cover laterally or displaced to the bottom on the housing VEGADIS 11 e 11 6 Setup Fig 5 With an individual instrument 1 Indicating module 2 Fixing screws O o o o Oo Oo e Q o Sw VEA A m E zw NH g em a p BOD DOOD 0000 MEE ee ee A o VEA O o 9 o B E o CIEBS D evea amp Fig 6 With several instruments mounted next to each other 1 Indicating module 2 Fixing screws 12 VEGADIS 11 L080t L N3 8886L 19888 EN 140801 VEGA 6 Setup Display elements Fig 7 Indicating elements of VEGADIS 11 Bar graph Tendency indication Digital value four positions as well as signa and decimal point individual scaling between 9999 9999 The display outputs the current 4 20 mA as bar graph and digital value With 4 mA no segment of the bar graph appears with 20 mA all seg ments appear This assignment is fix You can scale the digital value to any value between 9999 9999 via the adjustment module Adjustment steps scaling To scale the indication proceed as follows 1 ous N Ts 8 Initial value Set rotary switch to zero Set the
Download Pdf Manuals
Related Search