Installation manual for LA1, LA5, LA10, LA14, LA24
Contents
1. LA4Q oo rere De LA24 gt t LA1 OD Only mount actuator in LA1 o Fa14 O aT these points LAS O IA14 D lt LAI Trunnion option 3 LAIN vew LA24 p no D603 022 2x LA24 O 230 and 115 Vac supply with brake A22 xxxx xxxxBxxxx AA22 xxxxxMxxxxBxxxx FA14 Correct tightening torque 4 4 Nm Eaa O mie es 7 Bx 1 LA1 Only use solid pins w 1A14 O hs Las a 1A14 O 4 LA1 LAS LA10 an LATO 6 35 mm 12 7 mm black 1 LA1 O r7 p no D603 034 2x p no D603 028 2x FA14 LA14 LA24 FA14 1A14 LA5 se Res a orange 4 i 1A14 UW pino D603 023 2x LA10L 230 vac l white 3 LA14C 400 vac a x Sa _ 7 LA24 Capacitor 115 VAC 35 uF p no D900 448 002 230 VAC 10 uF p no D900 448 003 oe F AOOO 3 x 400 Vac supply without brake A42 xxxxxMxxxxNxxxx AA42 xxxxxMxxxxNxxxx PE yellow green n gt L1 white T holders O LAS TA I i red runnion holders option LA Pin holders option L3 black p no D603 030 2x LAS OD LA10 x j e gt no D603 029 2x LA10 0 wie or LA14 x LA14 LA24 1 LA24 FA14 FA14 1A14 J 3 x 400 Vac supply with brake A42 xxxxxMxxxxBxxxx AA42 xxxxxMxxxxBxxxx 1A14 PE yellowgreen i Current Curr2. 09 Kristianstad Sweden Pnntedioi tecyded paper Always turn power off before working on the actuator or the wiring Tel 46 0 44 246700 Fax 46 0 44 244085 the motor will keep running which may cause damage to the actuator mD DANA MOTION Solutions by HER TTHOMSON Installation manual for LA1 LA5 LA10 LA14 LA24 FA14 and IA14 actuators CE 115 VAC 230 VAC 115 VAC 400 VAC Basic mounting rules Basic mounting rules Connection of motor LA1 LA1 LA1 J Only mount actuator in LA1 O Motor flange LA1 LA5 LA5 LAs O these points LA5 O LA OD LA10 LA10 LA10 O Giescee nae etandard LA10 oO Drill hole and make key way in the LA10 oO La14 x Lag D LA14 Q gt i LA14 O coupling to fit your motor shaft The La14 O Trunnion option p no D603 022 2x coupling accepts holes between LA24 b LA24 aa d LA24 0 LA24 510 19 mm LA24 O FA14 X FA14 X FA14 916 FA14 x FA14 0 1A14 1A14 A 1A14 1A14 O Lat O Las O LA1 Only mount actuator in LA1 Restraining torque Lato x gt A LAS LAS aie LA14 x i black these points Torque needed to prevent extension LA24 LA10 LA10 tube from rotating E LA14 0 LA14 0 FA14 0 LAa240 lop LA24 O LAI 2 3Nm 14140 7 FA14 P FA14 1A14 S 1A14 g LAS MS Ni F Ca _ y LA1 _230 and 115 Vac supply without brake A22 xxxx xxxxNxxxx AA22 xxxxxMxxxxNxxxx LA10 11 3 Nm LA5 T o LA10 O PE yellow green
3. Connection of potentiometer optional Technical data R eee LAI ie Stroke R POTENTIOMETER DATA Las O LA10C LA10 LA14 LA24 yes FA14 0 red 36 VDC 30 40 V yes 1a14 O C yes 1 5 mm El Only accepts battery or full wave smoothed rectified voltage 0 Q between white and red when fully retracted Accepts battery full wave min stroke 0 Q Rx cm smoothed or unsmoothed rectified voltage 1 2 940 Q cm Max power 1 5 W DC motor with automatic reset LA14 white p thermal switch O R 3 4 470 Q cm Resistance tolerance 5 12 VDC 10 16 V yes yes LA24 C 5 6 315Q m Resistance linearity 0 25 24 VDC 20 32 V yes yes LA1 o AC motor with automatic reset LA5 Stroke R POTENTIOMETER DATA thermal switch 7 1115 VAC 102 130 V LA10 0 10 390 Q cm Max power 2W 17230 VAC 212 240 V LA14 11 20 200Q cm Resistance tolerance 5 3 400 VAC 360 420 V LA24 5 f 40 Capacitor necessa FA14 21 40 100 Q cm Resistance linearity 0 25 p ry 1A14 i eee Max current A L 1 5 mm Duty cycle full load 25 C 45 0 Q between yellow and Max on time s il grey when fully extended Restraining torque Nm 2 3 141 3 End play max mm 0 9 1 Ambient temperature C 25 65 Lubrication for life LA1 O Magnet position with extension Magnet position with extension Anti backdriving mechanism yes LA5
4. O tube fully retracted tube fully extended LA1 0 LA14 i Protection class LA24 End stroke limit switches FA14 j F j A Options 1A14 Slip clutch yes set to 1 2 1 5 x max dynamic load Feedback potentiometer Electrically released brake Reed switch sensors Actuator type Actuator designation L1 mm L2 mm Pins LA14 LA24 FA14 XAXX XXAXX 32 35 Pin holders LA14 LA24 FA14 IA14 XAXX XXBXX 92 20 Trunnion Trunnion holders The reed switch sensors should normally be placed about 25 mm before these eames A Do not use the thermal switch as oveload protection One full cycle at full load position in order to compensate for the distance needed for deceleration Reed switch sensor data Max power VA Max current A LA1 If using a LA1 actuator with integrated end stroke limit switches LA5 D designation Sxx xxAxx xxxx make sure to switch off the power to LA10 oO the motor if the extension tube can not extend or retract fully Otherwise LA140 Max voltage VDC Protection class IP 67 Part numbers normally open D535 070 normally closed D535 071 LA24 C k AO ee a m y We recommend to always install fuse or thermal breaker between motor Q Switch off power aX stroke y Switch off power min stroke and power supply to protect actuator wiring and other items Tollo Linear AB PRINTED IN SWEDEN 1994 dw110206 gb 0528 CAUTION n Box 9053 SE 291
5. ent Current L1 white A A A L2 red 0 15 f 0 10 0 12 L3 black 16 20 5 11 15 N The tables are based on ambient temperature 30 C or less
Download Pdf Manuals
Related Search