lamp hes-3030br concealed hinge for builders doors
Contents
1. leaves into the bores for a flush surface tighten the outer hole screws first o and then the inner hole screws D 5 While holding the door mount another leaf of the hinge to the bore in the frame with supplied mounting screws Flat head tapping screws 97 128 168 191 J 6 Tighten all the mounting screws properly to complete installation os E Caution 1 1 When mounting hinge leaves to door and frame the projection from the surface of door frame must be limited to 1mm otherwise it may cause damage to door frame and restrict the operation angle of the door See the Drawing 4 10 10 4 make a preparatory hole 036 38 a7 Counterbore Depth 2 After having mounted the hinge check whether or not the hinge surface is slanted as shown in the X3 30 0 Scale mm 21 Drawing 4 If the hinge is slanted loosen the screws and repeat the procedure 4 in the above a A a Installation Procedure for leveling When you are unable to correct the slant with this insert a chip of wood of appropriate thickness in the hole for mounting screws before fixing the screws Drawing 4 i HT 3 Check whether or not the screw heads are protruding from the surface of hinge leaves If the screw heads are protruding the door may not close completely See the Drawing 5 Drawing 2 Doors and Frames Fabrication Correct Incorrect Correct Incorrect Japan Hea2. LAMP HES 3030BR CONCEALED HINGE FOR BUILDERS DOORS INSTALLATION MANUAL Please follow this manual carefully for proper use CAUTION This concealed hinge is designed for builders doors We will not be liable for any injuries or damage due to improper installation disassembly modification or use on a door which exceed the specified dimensions and weights Do not open the door over 180 degrees or open close with excessive force It may cause malfunction or personal injury Drawing 1 Dimensions and Weights of E Dimensions and Weights of Applicable Doors for three hinges per door Applicable Doors f Height max 2 000mm 78 3 4 Thickness min 36mm 1 27 64 Frame Width max 900mm 35 7 16 Weight max 50kg 110 Ibs me i Door E Doors and Frames Fabrication Oreste 1 Due to the weight of the hinges the bottom edge of the door mounted with HES 3030BR slants to the opposite side of the hinges in a certain volume as shown by the broken lines in the Drawing 1 x lt When installing your door make a clearance X enough to cover such inclination between the door edge and the doorsill Refer to the Drawing 1 aes O G X Doorsill Thickness X must be a minimum of 6mm A 2 The above formula is based on the standard application of three HES 3030BR concealed hinges per door For standard application of 3 hinges to a door it is recommended to install the middle hinge
3. d Office a g U S Subsidiary SUGATSUNE KOGYO CO LTD SUGATSUNE SUGATSUNE AMERICA INC 1 8 11 Higashikanda Chiyodaku Tokyo 101 JAPAN 221 East Selandia Lane Carson CA 90746 U S A Phone 813 3866 2260 Fax 813 3866 4447 a a Phone 310 329 6373 Fax 310 329 0819 www sugatsune com Toll Free 1 800 562 LAMP
4. slightly above the midpoint of the door for reinforcement Doorsill eae de indicated by broken lines Drawing 2 E 3 21 Doors and Frames Fabrication 3 Doors and frames must be fabricated properly They must be warp free and the four corners must be square Improper fabrication may cause scraping of doors and frames against each other or abnormal noise m gt S Qa lt om 2 E To make bores in doors and frames for mounting hinges as small as possible Frame Frame If you chamfer the corners A of doors and frames with R2 or C2 the remaining thickness of doors can be increased from max 3 to max 4 and the remaining thickness of frames from max 5 to X max 7 See the areas indicated by in the Drawing 2 uae E Installation Procedure 1 Bore the door and frame as shown in the Drawing 3 The dimensions marked with in the ey NA Drawing 3 are for standard dimensions For non standard dimensions refer to the Drawing 2 Scale mm Dogi Door 2 For wooden doors holes for mounting screws must be made in the specified diameters For steel doors M4x0 7 female screws are recommended as mounting screws M4 flat head screws are recommended XMax 5 180 Drawing 3 Bore Fabrication Frame Door Side 3 Mount a leaf of the hinge to the door with supplied mounting screws Flat head tapping screws S o 4 In order to fit the hinge
Download Pdf Manuals
Related Search