AX4E-Centos5.4-Dahdi-User Manual-V1.0-EN
Contents
1. Does not increase the physical size of the card and no additional slot is required www atcom cn Email support atcomemail com 1 AXEIDL User Manual with DAHDI Voice Modes PRI CPE and PRI NET EuroISDN 4ESS AT amp T S5ESS Lucent DMS100 Hardware Requirement 1 6 Ghz Pentium IV 512 MB RAM PCI E slot AXE4DL Dimension 120mm Length 64mm height Operating System Linux all versions releases and distributions from 1 0 up www atcom cn Email support atcomemail com atcom atcom AXEIDL User Manual with DAHDI Chapter 2 Hardware Introduction Daughterboard Optional echo cancellation module Not available Bracket for full height LED N Bracket for low sai Ni AXEIDL The Front View of EC32L www atcom cn Email support atcomemail com atcom AXEIDL User Manual with DAHDI LED The LED of the four ports will be red clearly when the driver of the card is loaded correctly and the etc dahdi system conf file is configured correctly the LED will be green clearly when the PRI line is connected correctly and it synchronizes to the other equipment successfully C2 It is used for selecting El T1 JI mode In default it will be set it up according to users requirement before shipping out Users can set up E1 T1 J1 like the following For El Mode For T1 and J1 Mode C4 It is used when there are more than one PRI card in the one server For example if2. run the dahdi show channels command in the CLI Users will get 64 channels 5 How to check if the hardware echo cancellation works or not 1 After booting the server with the AXE2DL and the echo cancellation module please run the dmesg command to check if the hardware is detected or not Users will get the following information VPM450 echo cancellation for 64 channels wet4xxp 0000 05 04 0 VPM450 hardware DTMF disabled wet4xxp 0000 05 04 0 VPM450 Present and operational servicing 4 span s 2 When users are using the hardware echo cancellation module please disable the software echo cancellation in etc dahdi system conf and enable the parameter echocancel yes line in the etc asterisk chan_dahdi conf file After do that please restart dahdi and asterisk 3 Run asterisk and make a call by channel 1 users can get the following information marked with red line if the the echo cancellation module is working Notice If users enable the software echo cancellation it can get the following red lines also So please disable the software echo cancellation when users use the hardware cancellation localhost CLI gt dahdi show channel 1 Channel 1 File Descriptor 17 Span Extension 300 Dialing no Context from pstn Caller ID 900 Calling TON 33 Caller ID name 900 Mailbox none Destroy 0 InAlarm 0 www atcom cn Email support atcomemail com 10 www atcom cn AXEIDL User Manual
3. src tar xvzf libpri 1 4 14 tar gz 2 root localhost libpri 1 4 14 make 3 root localhost libpri 1 4 14 make install Install dahdi linux 4 root localhost src tar xvzf dahdi linux complete 2 6 2 2 6 2 xx tar gz 5 root localhost src cd dahdi linux complete 2 6 2 2 6 2 6 root localhost dahdi linux 2 6 2 make 7 root localhost dahdi linux 2 6 2 make install 8 root localhost dahdi linux 2 6 2 make config Install asterisk 1 root localhost src tar xvzf asterisk 1 8 7 0 tar gz 2 root localhost asterisk 1 8 7 0 configure 3 root localhost asterisk 1 8 7 0 make 4 root localhost asterisk 1 8 7 0 make install 5 root localhost asterisk 1 8 7 0 make samples Notice if uses run the command make samples all the asterisk configuration files will be set as the samples www atcom cn Email support atcomemail com 8 atcom AXEIDL User Manual with DAHDI Chapter 4 Software Configuration 1 Please run the dahdi_genconf command to configure the etc dahdi system conf file and generate etc asterisk dahdi channels conf file root localhost dahdi_genconf It will not show any output when the command run successfully After do that successfully it will get the following configuration in the system conf file with El mode root localhost cat etc dahdi system conf Autogenerated by usr sbin dahdi_genconf do not hand edit This file is parsed
4. users have two cards in the server then turn it to 0 in the one card and turn it to 1 in the other card If users have four cards in the server simultaneously then turn it to 0 1 2 3 respectively www atcom cn Email support atcomemail com 4 atcom AXEIDL User Manual with DAHDI C1 It is used to select the hardware echo cancellation direction In default It will not use the jumper and it will delete the echo for the far end side if users need delete the echo for the local side please use the jumper like the following illustration Delete the echo for the local side Delete the echo for the far end side C3 It is not available Notice The daughterboard is very similar between the AXE2DL and AXEIDL card Users can get the difference from the following illustration Daughterboard Daughterboard Not available AXE2DL daughterboard AXE1DL daughterboard www atcom cn Email support atcomemail com 5 atcom AXEIDL User Manual with DAHDI Chapter 2 Test Environment Test Environment Libpri 1 4 7 dahdi linux complete 2 6 2 2 6 2 Download from ATCOM download center asterisk 1 8 7 0 Centos6 0 kernel version 2 6 32 279 22 1 e16 1686 AXEI1DL EC64L www atcom cn Email support atcomemail com atcom AXEIDL User Manual with DAHDI Chapter 3 Software Installation After inserting the card into the PCI slot and boot the server please use the lspci command to check the PCI bus compatibility
5. with DAHDI Signalling Type ISDN PRI Radio 0 Owner DAHDI 1 1 Real DAHDI 1 1 Callwait lt None gt Threeway lt None gt Confno 1 Propagated Conference 1 Real in conference 0 DSP yes Busy Detection no TDD no Relax DTMF no Dialing CallwaitCAS 0 0 Default law alaw Fax Handled no Pulse phone no DND no Echo Cancellation 128 taps currently ON Wait for dialtone Oms PRI Flags Call PRI Logical Span Implicit Email support atcomemail com atcom atcom AXEIDL User Manual with DAHDI Chapter 5 Test 1 LED state LED If the driver of the card is loaded correctly and the etc dahdi system conf file is configured correctly the four ports of LED will be red clearly If the PRI line is connected correctly and it synchronizes to the other equipment successfully then the LED will be green clearly 2 Use the E1 T1 J1 cables to connect to the ports And Check the PRI state 1 Load the asterisk root localhost asterisk asterisk vvgr CLI gt reload 2 Check the PRI state users will get the following port information all the four ports are in up status localhost CLI gt pri show spans PRI span 1 0 Up Active PRI span 2 0 Up Active 3 Add the dial plan for the PBX Please edit the dial plan in the extensions conf file users can refer to the following example from internal exten gt _1 1 Dial dahdi il EXTEN 1 exten gt _1 2 Hangup from pstn exten gt s 1 Answer ex
6. EI1DL Asterisk card is the asterisk PCI E card which supports single ISDN PRI E1 T1 J1 ports optional with teleco grade hardware echo cancellation Using AXEIDL digital PRI card open source Asterisk PBX and stand alone PC users can create their IP PBX telephony solution included all the sophisticated features of traditional PBX and extended features such as voicemail in IP PBX With low profile design the AXE1DL is suitable for 2U server Features AXE4DL single ISDN PRI E1 T1 J1 ports Support original Dahdi Zaptel No patch Support Asterisk Freeswitch Yate Support Elastix Trixbox AsteriskNOW PBX in a Flash 100 compatible with all features of Asterisk PBX Supports standard telephony and data protocols Including PRI CAS CCS for voice and PPP HDLC Cisco HDLC and Frame Relay for data modes Supports chan_ss7 and Openr2 Optional hardware echo cancellation Select the hardware echo cancellation direction With low profile design the AXE2DL is suitable for 2U server Applications ISDN PRI IP PBX ISDN least cost router Calling Card Platforms IVR system Call Center Traditional Calls VoIP Calls Conference VoIP Gateway Callback Service Optional DSP Hardware Echo Cancellation Module G 168 2002 echo cancellation in hardware 1024 taps 128 ms tail per channel on all channel densities DTMF decoding and tone recognition Voice quality enhancement music protection acoustic echo control and adaptive noise reduction
7. From the correct output users can see the following line The AXEIDL will be found if users can not see one line like the line above please power off the server and try to use another PCI slot If it does not help still users have to check the compatibility issue between the card and the PCI E bus Please try to use another PCI E slot or other server and try it again 1 To install asterisk and dahdi users have to use yum command to install the following prerequisite packages yum install y bison bison devel zlib zlib devel openssl openssl devel gnutls devel gcc gcc c ncurses ncurses devel 2 Download libpri dahdi and asterisk packages Notice If uses need use the latest version please check them on asterisk download center root localhost src weet http downloads asterisk org pub telephony libpri libpri 1 4 14 tar gz root localhost src weet http downloads asterisk org pub telephony asterisk releases asterisk 1 8 7 0 tar gz Notice If the download link is unavailable uses need get the latest driver from ATCOM download center http www atcom cn dl_axeldlLhtml For example users can get the dahdi 2 6 as the following root localhost src weet http www atcom cn cn download cards ax1 d dahdi linux complete 2 6 1 2 6 1 1 2 tar gz www atcom cn Email support atcomemail com 7 atcom AXEIDL User Manual with DAHDI 3 Installation the packages Install libpri 1 root localhost
8. atcom W N W Ws SS Y y y NU AXE1DL EC32L ATCOWME Digital Card AXE1DL User Manual Version 2 0 2013 07 03 Wwww atcom cn Email support atcomemail com atcom AXEIDL User Manual with DAHDI Release note Version Changed note Editor Date 1 0 First Release 2 0 Release the User manual Deniel 2013 07 03 www atcom cn Email support atcomemail com atcom AXEIDL User Manual with DAHDI Content CHAPTER 1 THE INTRODUCTION OF AXE 1 DBL ccccccscsccsscccsscccssccccsccccsccccscceccccesccccsccccsccccsccccccsccees 3 CHAPTER 2 HARDWARE INTRODUCTION cccccccsccccscccccsccccsccccsccccsccesccccscccesccccsccccsccescccescccesccecscceees 5 CHAPTER 2 TEST ENVIRONIMENT cccccccssscesssccsscccssccessccessccsonccsonccssccesscccssccsssccsssccsccccsscocsccessscossscosscces 8 CHAPTER 3 SOFTWARE INSTALLATION ccccccsccccccccccccccccccccccccccccccccccccccccccscccccccescccescccesccccsccccsccescccess 9 CHAPTER 4 SOFTWARE CONFIGURATION ccccsscccsscccssccccsccccscccccccccccccccccccccccsccccccccccccccccccccecccccccccees 11 CHAPTER 5 TEST vescwnssiceccsassseuscccewsccsvcevsecscvecsibeceuvesuvesseceeseveesuievevvevewss 8oeceveess sesoesecebeswosnceosncesencevencesouce eues 14 CHAPTER 6 REFERENCE iiss ccceceveccecseccscacevesscuceceecdececccsesddecdddesteseeocdescctesecocseosseeseceussscosscdueseGosscsuswcecsoesesees 16 www atcom cn Email support atc
9. by the Dahdi Configurator dahdi_cfg Span 1 AXE1DL 0 1 AXE1DL E1 T1 Card 0 Span 1 MASTER span 1 1 0 ccs hdb3 crce4 termtype te bchan 1 15 17 31 dchan 16 echocanceller mg 2 1 15 17 31 After running dahdi_genconf successfully the dahdi channels conf file will get the following configuration root localhost cat etc asterisk dahdi channels conf Autogenerated by usr sbin dahdi_genconf on Mon Aug 5 15 02 51 2013 If you edit this file and execute usr sbin dahdi_genconf again your manual changes will be LOST Dahdi Channels Configurations chan_dahdi conf This is not intended to be a complete chan_dahdi conf Rather it is intended to be include d by etc chan_dahdi conf that will include the global settings Span 1 AXEIDL 0 1 AXEIDL E1 T1 Card 0 Span 1 MASTER group 0 11 context from pstn switchtype euroisdn signalling pri_cpe channel gt 1 15 17 31 context default group 63 www atcom cn Email support atcomemail com 9 atcom AXEIDL User Manual with DAHDI 2 Please add the line include dahdi channels conf into the end of the chan_dahdi conf file And users can run the following command to add it to the file root localhost echo include dahdi channels conf gt gt etc asterisk chan_dahdi conf 3 Please run asterisk with the following command root localhost asterisk root localhost asterisk vvgr root localhost reload 4 Please
10. omemail com atcom AXEIDL User Manual with DAHDI Contact ATCOM The Introduction of ATCOM ATCOM is the leading VoIP hardware manufacturer in global market We have been keeping innovating with customer s needs oriented working with partners to establish a total solution for SMB VoIP with IP phone IP PBX and Asterisk cards With over 10 years experience of R amp D manufacturing and service in network and VoIP filed mission of creating the biggest value for IP terminals we commit ourselves in supplying the competitive IP phone and other terminals for IP PBX softswitch IMS NGN providers and carriers supplying the competitive total VoIP solution for SMB market We keep improving the customer s experience and creating the bigger value with our reliable products Until now our VoIP products has been sold to over 60 countries and used by millions of end users Contact sales Address District C east of 2nd floor 3 Crown industry buildings Chegongmiao Industry area Futian district Shenzhen China Tel 86 755 23487618 Fax 86 755 23485319 E mail sales atcomemail com Contact Technical Support Tel 86 755 23481119 E mail Support atcomemail com Website address http www atcom cn Download Center http www atcom cn download html www atcom cn Email support atcomemail com Chapter 1 the Introduction of AXE1IDL Overview of the AXEIDL AX
11. ree ports in the same way www atcom cn Email support atcomemail com 13 atcom AXEIDL User Manual with DAHDI Chapter 6 Reference http www asteriskguru com http www asterisk org downloads http www atcom cn www atcom cn Email support atcomemail com
12. ten gt s 2 Dial sip 500 exten gt s 3 hangup www atcom cn Email support atcomemail com 12 atcom AXEIDL User Manual with DAHDI 4 Use a registered sip phone to make an outgoing call According to the dial plan above if users want to make the outgoing call via the first port users have to add a prefix 1 If users want to make a calling via the second port users have to add a prefix 2 For example the destination number is 0755 83018618 so dialing 0755 83018618 And then users can get the following output from asterisk CLI CLI gt Using SIP RTP CoS mark 5 Executing 83018618 from internal 1 Dial SIP 500 00000003 dahdi 1 83018618 in new stack Called 1 83018618 DAHDI 1 1 answered SIP 500 00000003 The called party ringing and pick up the phone so the call is successful 5 Please use a phone to make an incoming call For example the number of the PRI line is 0755 23485319 using a phone to dial 0755 23485319 The sip 500 rings and users can get the following output from asterisk CLI CLI gt Starting simple switch on DAHDI 1 1 Jul 1 11 42 53 NOTICE 20678 chan_dahdi c 8734 ss_thread Got event 18 Ring Begin Executing s from pstn 1 Answer DAHDI 1 1 in new stack Executing s from pstn 2 Dial DAHDI 1 1 sip 500 in new stack Using SIP RTP CoS mark 5 Called 500 SIP 500 00000004 is ringing SIP 500 00000004 answered DAHDI 1 1 Users can test other th
Download Pdf Manuals
Related Search