Home

User manual

1. Load Fail Safe Defaults This option opens a dialog box that lets you load fail safe defaults for all appropriate items in the Setup Utility The fail safe defaults place no great demands on the system and are generally stable If the system is not functioning correctly try loading the fail safe defaults as a first step in getting the system working properly again If you only want to load fail safe defaults for a specific option select and display that option and then press lt F6 gt Follow these instructions to load the fail safe defaults 1 From the main menu scroll to Load Fail Safe Defaults 2 Press lt Enter gt to open the Load Setup Fail Safe Defaults menu 3 Press lt Y gt 4 Press lt Enter gt to load the defaults Load Optimized Defaults This option opens a dialog box that lets you load optimized defaults for all appropriate items in the Setup Utility The optimized defaults place demands on the system that may be greater than the performance level of the components such as the CPU and the memory You can cause fatal errors or instability if you load the optimized defaults when the hardware does not support them If you only want to load Setup defaults for a specific option select and display that option and then press F7 Follow these instructions to load the optimized defaults 1 From the main menu scroll to Load Optimized Defaults 2 Press Enter to open the Load Optimized Defaults menu 3 Press Y
2. 12 Plug in the two cables to CN15 and CN3 on the mainboard 13 Replace the I O board 14 Replace the mainboard cover Installing a PCI E x1 card Refer to the following to install a PCI E x1 card Remove the rear cover See Removing the rear cover on page 6 2 Insert the PCI E x1 card 3 Secure the card with one screw Ensure there are no cables preventing the PCI E card from connecting to the mainboard NOTE 42 CHAPTER 3 UPGRADING COMPONENTS APPENDIX This appendix describes locating and solving problems that you may encounter while using the PT 8850 POS Troubleshooting Often after time spent troubleshooting the problem is traced to something as simple as a loose connection Check the following before proceeding to the problem specific solutions Tips for Troubleshooting In each problem specific section try the steps in the order suggested This may help you to solve the problem more quickly Try to pin point the problem and thus avoid replacing non defective parts For example if you replace batteries and the problem remains put the original batteries back and go to the next step Keep a record of the steps you take when troubleshooting The information may be useful when calling for technical support or for passing on to service personnel Use some other electrical device to confirm that the electrical outlet is working Ensure all connections are securely a
3. 2 Connect the RJ 11 cable from the cash drawer to the RJ 11 connector on the PT 8800 8 Chapter 1 Getting Started J O9 Le Cashdrawer 3 Turn on the PT 8800 See Powering the PT 8800 on and off below Powering the PT 8800 on and off Refer to the following to power on and off the PT 8800 1 Remove the rear cover See Removing the rear cover on page 6 2 Connectthe power cable to the power con nector on the PT 8800 and to an electrical outlet 3 Liftthe cover 4 Press the power button The power LED turns on 5 Toturn off the PT 8800 shut down the operating system the main power turns off automatically Power LED operating system you are using does not support power down by the OS or if the system crashes or hangs lp You may need to use the power button to turn off the power for example if the NOTE Powering the PT 8800 on and off 9 10 Chapter 1 Getting Started CHAPTER 2 UPGRADING COMPONENTS This chapter describes how to upgrade components for the PT 8800 The following topics are described Safety and precautions Before you begin on page 12 Installing a hard disk drive HDD on page 12 Installing optional displays on page 13 nstalling a CompactFlash card on page 17 nstalling a PCI card on page 18 Safety and precautions Computer components and electronic circuit boards can be damaged
4. 6 Link LED orange lights when the network is found il COM2 connector 8 RJ 11 cash drawer connector 9 Powered USB connector 24V connect peripherals such as USB printers 10 Powered USB connector 12V connect peripherals such as a customer display 11 RJ 45 LAN connector 12 Mic in 13 COM3 connector 14 VGA connector 15 COM1 connector 16 PS 2 keyboard connector Powered USB peripherals have keyed connectors to match the 12V and 24V powered USB connectors on the machine Do not try to force a 12V connector from a peripheral into the 24V connector on the machine You can also connect standard USB devices to the powered USB connectors For powered USB 1 24V cannot exceed 2A 2 12V cannot exceed 3A IMPORTANT 3 Total of 24V amp 12V cannot exceed 48 watts Plugging a phone line into the LAN port RJ 45 connector can damage the connector Take care to only plug an RJ 45 connector into the LAN CAUTION PO L COM 6 is reserved for the optional customer display NOTE Removing the rear cover Refer to the following to remove the rear cover 1 Open the rear cover latches 2 Remove the rear cover 6 CHAPTER 1 GETTING STARTED When replacing Align the rear cover tab with the opening on the machine Adjusting display angles The main display can be tilted back from an upright perpendicular position to about 30 degrees as shown in Figure 1 5 The customer display can be tilte
5. Caution Inserting the card incorrectly can damage the connector pins Ensure the card is oriented as shown and insert it gently Note that a properly installed card still protrudes as shown here Installing a CompactFlash card 17 3 Toremove a card press the eject button and pull the card out Installing a PCI card Refer to the following to install a PCI card 1 Remove the rear cover See Removing the rear cover on page 6 2 Insert the PCI card 3 Secure the card with one screw Dy Ensure there are no cables preventing the PCI card from connecting to the main board 18 Chapter 2 Upgrading Components CHAPTER 3 BIOS SETUP UTILITY The BIOS Basic Input and Output System Setup Utility displays the system s configuration status and provides options to set system parameters The parameters are stored in battery backed up CMOS RAM that saves this informa tion even when the power is turned off When the system is turned back on the system is configured with the values found in CMOS The following topics are described in this chapter About the Setup Utility Entering the Setup Utility on page 20 Standard CMOS Features on page 21 Advanced BIOS Features on page 24 ntegrated Peripherals on page 28 Power Management Setup Option on page 32 PnP PCI Configurations on page 35 Frequency Voltage Control Option on page 37 Other BIOS
6. IMPORTANT 1 Remove the rear cover See Removing the rear cover on page 6 2 Connect the RJ 11 cable from the cash drawer to the RJ 11 connector on the machine 8 CHAPTER 1 GETTING STARTED ess 9 9 Lr 4 C 3 Turn on the machine See Powering the machine on and off below Powering the machine on and off Refer to the following to power on and off the machine Remove the rear cover See Re moving the rear cover on page 6 Connect the power cable to the power connector on the machine and to an electrical outlet Lift the cover Press the power button The power LED turns on To turn off the machine shut down the operating system the main power turns off automati cally You may need to use the power button to turn off the power for example if the operating system you are using does not support power down by the OS or if the system crashes or hangs NOTE 10 CHAPTER 1 GETTING STARTED CHAPTER 2 BIOS SETUP The primary function of the BIOS Basic Input and Output System is to identify and initiate component hardware The BIOS parameters are stored in non volatile BIOS memory CMOS CMOS contents don t get erased when the computer is turned off The following topics are described in this chapter About the Setup U
7. IDE Channel 0 Master gt IDE Channel 0 Slave gt IDE Channel 1 Master gt IDE Channel 1 Slave gt IDE Channel 2 Master Figure 2 2 Standard gt IDE Channel 3 Master p CMOS Features menu Video Halt On ti Move Enter Select PU PD Value F10 Save ESC Exit Fl General Help F5 Previous Values F6 Fail Safe Defaults F7 0ptimized Defaults Date and Time The Date and Time items show the current date and time held by the machine If you are running a Windows OS these items are automatically updated whenever you make changes to the Windows Date and Time Properties utility Video These fields is used to select the default video device Halt On This item defines the operation of the system POST Power On Self Test routine You can use this item to select which types of errors in the POST are sufficient to halt the system Base Memory Extended Memory and Total Memory These items are automatically detected by the system at start up time These are display only fields You cannot make changes to these fields Base Memory This field displays the amount of conventional memory detected by the system during boot Extended Memory This field displays the amount of extended memory detected by the system dur ing boot Total Memory This field displays the total amount of memory Base and Extended detected by the system during boot 14 CHAPTER 2 BIOS SETUP IDE Channel 0 2 3 Master Slave This field is used to configure
8. Interrupt ReQuests and DMAs Direct Memory Access You must set up the IRQ and DMA assignments correctly through the PnP PCI Configurations menu otherwise the mainboard will not work properly Selecting PnP PCI Configurations on the main menu displays this menu Phoenix AwardBIOS CMOS Setup Utility PnP PCI Configurations Init Display First Item Help Reset Configuration Data Resources Controlled By PCI VGA Palette Snoop Sis ea Figure 2 14 PnP PCI INT Pin 2 Assignment INT Pin 3 Assignment Configuration menu INT Pin 4 Assignment INT Pin 5 Assignment INT Pin 6 Assignment INT Pin 7 Assignment INT Pin 8 Assignment Maximum Payload Size t12 Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 0ptimized Defaults Init Display First Use this item to specify whether the graphics adapter is installed in one of the PCI slots or is integrated on the mainboard Reset Configuration Data If you enable this item and restart the system any PnP configuration data stored in the BIOS Setup is cleared from memory Resources Controlled By You should leave this item at the default Auto ESCD Under this setting the system dynamically allocates resources to plug and play devices as they are required If you cannot get a legacy ISA Industry Standard Architecture expansion card to work properly you might be able to solve the problem by changing this item to Manual an
9. Make sure you have a stable clean working environment Dust and dirt can get into components and may cause malfunction Adequate lighting and proper tools can prevent you from accidentally damaging the internal components Most of the electrical and mechanical connections can be disconnected by using your fingers It is recommended that you do not use needle nosed pliers to disconnect connectors as these can damage the soft metal or plastic parts of the connectors N To prevent scratching the case of the machine make sure the worktop surface is clean and flat CAUTION 36 CHAPTER 3 UPGRADING COMPONENTS Upgrading the hard drive Refer to the following to remove and replace the hard drive 1 Turn off the machine properly through the operating system 2 Disconnect the power cord from the power outlet 3 Remove the rear cover See Removing the rear cover on page 6 4 Remove the two thumbscrews 5 Remove the hard drive bracket 6 Place the new hard drive in the bracket 7 Secure the hard drive with four Screws 8 Connect the two cables 9 Replace the hard drive bracket 10 Replace the two thumbscrews 37 Installing optional displays The PT 8850 may ship with a customer display attached If you ordered the display separately refer to the following to attach it 1 Turn off the machine properly through the operating system 2 Disconnect the power cord from t
10. PU PD Value F10 Save ESC Exit Fl General Help F5 Previous Values F6 Fail Safe Defaults F7 0ptimized Defaults USB 1 0 Controller This item must be enabled to use the Universal Serial Bus ports on the mainboard USB 2 0 Controller The USB 2 0 Controller item allows USB 2 0 functionality USB Operation Mode This item is used to select the speed mode of USB USB Keyboard Function Enable this item if you plan to use a keyboard connected through the USB port in a legacy operating system such as DOS that does not support Plug and Play USB Mouse Function Enable this item if you plan to use a mouse connected through the USB port in a legacy operating system such as DOS that does not support Plug and Play USB Storage Function Enable this item if you plan to use a storage connected through the USB port in a legacy operating system such as DOS that does not support Plug and Play 26 CHAPTER 2 BIOS SETUP Power Management Setup Use these items to control system power management Modern operating systems take care of much of the power management This mainboard supports ACPI Advanced Configuration and Power Interface Phoenix AwardBIOS CMOS Setup Utility Power Management Setup ACPI Function Item Help ACPI Suspend Type RUN VGABIOS if S3 Resume Power Management Video Off Method Video Off In Suspend Suspend Type MODEM Use IRQ Suspend Mode Figure 2 13 Power Soft Off by PWR BTTN Management Setup menu Pow
11. from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes Trademark recognition All product names used in this manual are the properties of their respective owners and are acknowledged Federal Communications Commission FCC This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guar antee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment onto an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Shielded interconnect cables and a shielded AC power cable must be employed with this equip
12. 4 Press Enter to load the defaults 32 CHAPTER 2 BIOS SETUP Set Supervisor and User Passwords These items can be used to install a password A Supervisor password takes precedence over a User password and the Supervisor can limit the activities of a User To install a password follow these steps 1 Highlight the item Set Supervisor User Password on the main menu and press Enter 2 The password dialog box appears Enter Password 3 If you are installing a new password type in the password You cannot use more than eight characters or numbers The Set Supervisor User Password item differentiates between upper and lower case characters Press Enter after you have typed in the password If you are deleting a password that is already installed press Enter when the password dialog box appears You see a message that indicates that the password has been disabled PASSWORD DISABLED Press any key to continue 4 Press any key You are prompted to confirm the password Confirm Password 5 Type the password again and press lt Enter gt or press lt Enter gt if you are deleting a password that is already installed Write the passwords down and keep them in a safe place If you do not save changes when you exit BIOS changes to the pass words are saved anyway IMPORTANT Save amp Exit Setup Highlight this item and press Enter to save the changes that you have made in the Setup Utility and e
13. Confirm that the printer is on line Check the cable connection Check the mouse or keyboard with another computer to see if it works If the same problem occurs replace the mouse or keyboard The screen is blank and you don t hear any beeps Check that the AC adapter is connected to the PT 8800 and the power cord is plugged into a working electrical outlet Check that the power is on Press the power switch again for confirmation The screen is blank and you hear a continu ous beep or two or more beeps Only the cursor appears Have the PT 8800 serviced Reinstall the operating system and power on the PT 8800 Audio problems Ensure the audio cable is not defective The mute is off Troubleshooting 43 Having the PT 8800 Serviced If you are unable to solve the problem you should have the projector serviced Pack the projector in the original car ton See Unpacking the PT 8800 on page 1 Include a description of the problem and a checklist of the steps you took when trying to fix the problem The information may be useful to the service personnel Return the projector to the place you purchased it Specifications ITEM DESCRIPTION Processor Socket 478 Intel Pentium 4 up to 2 8 GHz Celeron 2 0 2 6 GHz System bus FSB speed 400 533 MHz Memory 2 x 184 pin DDR DIMM support 266 333 MHz DDR SDRAM expandable to 2 GB Chipset Intel 852 G
14. E Compliancy Mode Figure 2 8 PCI Express Root Port Func submenu tj Move Enter Select PU PD Value F10 Save ESC Exit Fl General Help F5 Previous Values F6 Fail Safe Defaults F7 0ptimized Defaults PCI Express Port 1 This item is used to enable disable the PCI Express port 1 PCI Express Port 2 This item is used to enable disable the PCI Express port 2 PCI E Compliancy Mode This feature allows you to set the version of the PCI Express base specifications by which the mainboard has to comply 21 Integrated Peripherals This option defines the operation of peripheral components on the system s input output ports Phoenix AwardBIOS CMOS Setup Utility Integrated Peripherals gt OnChip IDE Device Item Help gt SuperIO Device Coml With Voltage Com2 With Voltage Com3 With Voltage Com4 With Voltage Onboard Serial Port 3 Serial Port 3 Use IRQ Figure 2 9 Integrated Onboard Serial Port 4 Serial Port 4 Use IRQ Peripherals menu Onboard Serial Port 5 Serial Port 5 Use IRQ Onboard Serial Port 6 Serial Port 6 Use IRQ gt USB Device Setting t Move Enter Select PU PD Value F10 Save ESC Exit Fl General Help F5 Previous Values F6 Fail Safe Defaults F7 0ptimized Defaults Com1 2 3 4 With Voltage COM1 2 3 4 port can be set to supply both data and power to the peripherals that connect to them Check if the device you connect needs power from the COM1 2 3 4 port or if it has its own power supply The fa
15. Options on page 38 About the Setup Utility The BIOS Setup Utility enables you to configure the following items Hard drives diskette drives and peripherals Video display type and display options Password protection from unauthorized use Power management features If you have made settings that you do not want to save use the Exit Without Saving item and press Y to discard any changes you have made This Setup Utility should be used for the following When changing the system configuration When a configuration error is detected and you are prompted to make changes to the Setup Utility e When trying to resolve IRQ conflicts When making changes to the Power Management configuration When changing the User or Supervisor password 19 Entering the Setup Utility When you power on the system BIOS enters the Power On Self Test POST routines POST is a series of built in diagnostics performed by the BIOS After the POST routines are completed the following message appears Press DEL to enter SETUP Press the delete key Delete to access the Award BIOS Setup Utility Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Frequency Voltage Control Advanced BIOS Features Load Fail Safe Defaults Advanced Chipset Features Load Optimized Defaults integrated Peripherals Set Supervisor Password Power Management Setup Set User Password PnP PCI Configurations Save amp Exit Setup PC Health Status Exit W
16. Primary Secondary IDE 0 1 When these items are enabled the system will restart the power saving timeout counters when any activity is detected on any of the drives or devices on the primary or secondary IDE channels 34 Chapter 3 BIOS Setup Utility PnP PCI Configurations This option configures how PnP Plug and Play and PCI expansion cards operate in the system Both the ISA and PCI buses on the mainboard use system IRQs Interrupt ReQuests and DMAs Direct Memory Access You must set up the IRQ and DMA assignments correctly through PnP PCI Configurations otherwise the mainboard will not work properly Selecting PnP PCI Configurations on the main menu displays this menu Phoenix AwardBIOS CMOS Setup Utility PnP PCI Configurations Reset Configuration Data Disabled Item Help Resources Controlled by Auto ESCD Menu Level P x IRQ Resources Press Enter PCI VGA Palette Snoop Disabled OM ae d capable operating system Select No if you need the BIOS to configure non boot devices TL lt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 3 11 PnP PCI Configurations menu Reset Configuration Data If you enable this item and restart the system any PnP configuration data stored in the BIOS Setup is cleared from memory The default setting is Disabled Resources Controlled By You should leave this item at the default
17. display into place 4 Connect the customer display cable to CN14 See Mainboard reference on page 14 5 Secure the display with the supplied screw 6 Replace the mainboard cover DC 12V lp To supply power to the customer display the COMG voltage is factory set to Installing optional displays 15 Attaching the second display Refer to the following to attach the second display 1 Remove the two thumbscrews 2 Remove the I O board 3 Passthe diplay cables through the indicated opening 4 Secure the display bracket with the four supplied screws p 16 Chapter 2 Upgrading Components 5 Putthe bracket cover on 6 Plug in the two cables to CN15 and CN23 See Mainboard reference on page 14 7 Replace the I O board 8 Replace the mainboard cover Installing a CompactFlash card The CompactFlash card reader uses an IDE Integrated Drive Electronics interface and only supports storage cards Plug and play is not supported so cards have to be installed before you turn the PT 8800 on After installing a Compact Flash card close the cover to prevent the card being accidently removed while power is on Refer to the following to install a CompactFlash card 1 Usea thin plastic spatula to lift the cover To prevent unauthorized removal of a card the cover is designed not to open easily 2 Insert the CompactFlash card as shown
18. materials If you need to ship it in the future repack it as shown in Figure 1 1 Checking the package contents After you unpack the device check that the following items are included Driver CD with drivers and the user manual PDF file PT 8850 Second display optional rd MSR display optional Power Cable If any item is missing or appears damaged contact your dealer immediately 2 CHAPTER 1 GETTING STARTED Identifying components This section describes the parts and connectors on the machine Front right view 12 3 Figure 1 2 Front right view Component Description i 15 inch TFT LCD touch screen 2 Smart card reader 3 Speakers 4 Power LED 5 Power button 6 Two USB ports Rear view Figure 1 3 Rear view Component Description Customer display cover 2 MSR module Mainboard cover Rear cover S Rear cover latches 4 CHAPTER 1 GETTING STARTED Rear connectors Following shows the connectors on the rear of the machine You must remove the rear cover to access the connectors See Removing the rear cover on page 6 5227 16 15 14 13 Figure 1 4 Rear connectors labeled Connector Description 1 PS 2 mouse connector 2 Parallel connector 3 COM4 connector 4 Line out S Act LED green lights when network activity is detected
19. menu Phoenix AwardBIOS CMOS Setup Utility SuperlO Device Onboard COM1 3F8 IRQ4 Item Help Com1 With Voltage None Onboard COM2 2F8 IRQ3 Menu Level We COM2 With Voltage None Onboard LPT1 378 IRQ7 LPT1 Port Mode SPP ECP Mode Select EPP1 7 ECP Mode Use DMA 3 Onboard COM3 3E8 IRQ5 COM3 With Voltage None Onboard COM4 2E8 IRQ5 COM4 With Voltage None Onboard COM5 4F8 IRQ5 Onboard COM6 4E8 IRQ5 Tl Move Enter Select PUIPD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 3 9 Super IO Device menu Onboard COM1 This option is used to assign the I O address and IRQ for the onboard COM port 1 The default setting is 3F8 IRQ4 COM1 2 3 4 With Voltage COM ports can be set to supply both data and power to the peripherals that connect to them Check if the device you connect needs power from the COM port or if it has its own power supply The factory setting for the COM ports is None The voltage for the COM ports is set at None at the factory However for example to provide power to an installed customer display this setting must be set at 12V li for the corresponding COM port For a 5V device such as a barcode scanner the IMPORTANT setting should be 5V Onboard COM2 This option is used to assign the I O address and IRQ for the onboard COM port 2 The default setting is 2F8 IRQ3 LPT1 Port Mode Enables you to set the data tran
20. on the task bar or in the control panel If the date and time become incorrect after a short time the CMOS battery may be depleted Replace the battery The following message appears at boot up Invalid system disk Replace the disk and then press any key Ensure that an operating system is installed Check the boot sequence in the BIOS setup utility You hear irregular beeps during operation of the computer and the system halts Have the PT 8850 serviced An unidentified message is displayed Reboot the computer and run the BIOS Setup Utility Confirm the Setup Utility parameters If the same message is displayed after booting up again have the PT 8850 serviced You cannot operate the printer Check the printer cable connection Ensure that the printer power switch is turned on Confirm that the printer is on line You cannot use a mouse or keyboard Check the cable connection Check the mouse or keyboard with another computer to see if it works If the same problem occurs replace the mouse or keyboard The screen is blank and you don t hear any beeps Check that the AC adapter is connected to the PT 8850 and the power cord is plugged into a working electrical outlet Check that the power is on Press the power switch again for confirmation The screen is blank and you hear a continuous beep or two or more beeps Have the PT 8850 serviced Only the cursor appears R
21. optional displays The PT 8800 may ship with a customer display attached or you can order one and install it An optional second display can also be installed Before installing the optional displays you must remove the mainboard cover and the top rear cover Removing the mainboard cover and customer display cover Refer to the following to remove the rear cover 1 Remove the two thumbscrews 2 Remove the mainboard cover 3 Bowthecover up slightly to release the two tabs 4 Remove the customer display cover Installing optional displays 13 When replacing Align the customer display cover tabs with the openings on the PT 8800 Mainboard reference When connecting the displays refer to the following for connector locations on the mainboard LL CN23 S CN15 14 Chapter 2 Upgrading Components Attaching the customer display The PT 8800 may ship with a customer display attached If you ordered the display separately refer to the following to attach it 1 Pass the cable through the opening in the PT 8800 2 Align the tabs on the customer display with the openings on the PT 8800 3 Slide the customer
22. power manage ment This mainboard supports ACPI Advanced Configuration and Power Interface Power Management Timeouts The power saving modes can be controlled by timeouts If the system is inactive for a time the timeouts begin count ing If the inactivity continues so that the timeout period elapses the system enters a power saving mode If any item in the list of Reload Global Timer Events is Enabled then any activity on that item will reset the timeout counters to zero Wake Up Calls If the system is suspended or has been powered down by software it can be resumed by a wake up call that is gener ated by incoming traffic to a modem a LAN card a PCI card or a fixed alarm on the system realtime clock 32 Chapter 3 BIOS Setup Utility Phoenix AwardBIOS CMOS Setup Utility Power Management Setup ACPI function Power Management Video Off Method Video Off In Suspend Suspend Type MODEM Use IRQ Suspend Mode HDD Power Down Soft Off by PWR BTN Wake Up by PCI card Power On by Ring Resume by Alarm Date of Month Alarm Time hh mm ss Alarm Reload Global Timer E Primary IDE 0 Primary IDE 1 Secondary IDE 0 Tl Move Enter Select Help F5 Previous Values Enabled Item Help User Define V H SYNC Blank Yes Stop Grant 3 Disabled Disabled Instant Off Disabled Disabled Disabled 0 Menu Level M 0 0 Disabled Disabled Disabled ti IPU PD Value F10 Save E
23. the IDE hard drive installed in the system Move the cursor to highlight the IDE Primary Secondary Master Slave fields and press Enter The IDE Primary Master submenu opens Phoenix AwardBIOS CMOS Setup Utility IDE Channel 1 Master IDE HDD Auto Detection Item Help IDE Channel 1 Master Access Mode Figure 2 3 IDE Primary Master submenu ti Move Enter Select PU PD Value F10 Save ESC Exit Fl General Help F5 Previous Values F6 Fail Safe Defaults F7 0ptimized Defaults IDE HDD Auto Detection Press Enter while this item is highlighted if you want the Setup Utility to automatically detect and configure a hard disk drive on the IDE channel If you are setting up a new hard disk drive that supports LBA mode more than one line will appear in the parameter box Choose the line that lists LBA for an LBA drive NOTE IDE Channel 0 1 2 3 Master Slave If you leave this item at Auto the system will automatically detect and configure any IDE devices it finds If it fails to find a hard disk change the value to Manual and then manually configure the drive by entering the characteristics of the drive in the fields described below e Capacity displays the capacity of the HDD in gigabytes GB e Cylinder indicates the number of cylinders that the HDD has A cylinder is the sum total of all tracks that are in the same location on every disk surface Head displays the number of heads in the HDD A head is a device that r
24. 80GB or above 4 COM ports 1 RJ11 port 1 PS2 Mouse port 1 PS2 Keyboard port 1 Parallel port 1 RJ 45 port 4 USB portt 2 Powered USB with 12VDC amp 24VDC on rear IO panel 1 MIC IN port 1 LINE OUT port 1 VGA port Operation System POSReady 2009 Windows XP 2000 CE Net Linux Fedora Red Head 47 Power Supply ACI115 230V 220watt Power supply Dual or three track magnetic reader 15 Dual Screen uSSD Peripherals Mini PCI e optional PCI E X1 Biometric Reader Smart Card Reader I Button KB 32 32 key keypad 2x20 VFD customer display Operating Temperature 0 40 C Temperature Storage Temperature 20 60 C Pu Operation Humidity 20 80 Hygtuity Storage Humidity 1096 8095 Certification CE FCC UL CB VCCI BSMI 48 APPENDIX Copyright This publication including all photographs illustrations and software is protected under international copyright laws with all rights reserved Neither this manual nor any of the material contained herein may be reproduced without writ ten consent of the author Disclaimer The information in this document is subject to change without notice The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose The manufacturer reserves the right to revise this publication and to make changes
25. 85 V 12 V 12 19 V VBAT V 3 36 V 5VSB V 472V TL lt lt Move Enter Select i IPU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 3 12 PC Health Status menu Press lt Esc gt to return to the main menu 36 Chapter 3 BIOS Setup Utility Frequency Voltage Control Option This item enables you to set the clock speed and system bus for your system The clock speed and system bus are determined by the kind of processor you have installed in your system Phoenix AwardBIOS CMOS Setup Utility Frequency Voltage Control juo Den CIC ETC Spread Spectrum Disabled Menu Level M TL lt Move Enter Select iHPU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 3 13 Frequency Voltage Control Auto Detect PCI Clk When enabled BIOS disables the clock signal of unpopulated PCI slots reducing power consumption The default set ting is Enabled Spread Spectrum Enable this item to significantly reduce the EMI Electro Magnetic Interference generated by the system The default setting is 0 45 Press lt Esc gt to return to the main menu Frequency Voltage Control Option 37 Other BIOS Options This section covers the other options that are available from the main menu Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features gt CPU Frequency Control Advanc
26. Auto ESCD Under this setting the system dynamically allocates resources to plug and play devices as they are required If you cannot get a legacy ISA Industry Standard Architecture expan sion card to work properly you might be able to solve the problem by changing this item to Manual and then opening up the RQ Resources menu IRQ Resources This menu can only be accessed when the Resources Controlled by menu is set to Manual In the RQ Resources menu if you change any of the IRQ assignations to Legacy ISA then that Interrupt Request Line is reserved for a legacy ISA expansion card Press lt Esc gt to close the IRQ Resources menu PCI VGA Palette Snoop This item is designed to overcome some problems that can be caused by some non standard VGA cards This main board includes a built in VGA system that does not require palette snooping so you must leave this item disabled The default setting is Disabled Press lt Esc gt to return to the main menu Power Management Setup Option 35 PC Health Status On mainboards that support hardware monitoring this item lets you monitor the parameters for critical voltages criti cal temperatures and fan speeds You cannot make any changes to these fields They are display only Phoenix Award WorkstationBIOS CMOS Setup Utility PC Health Status Current System FAN Speed 0 RPM Current System FAN Speed 2836 RPM Menu Level M INO V 1 23 V IN1 V 153V IN2 V 344 V 5 V 5 18 V 12 V 11
27. CMOS Features on the main menu displays the following menu Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Date mm dd yy Fri Sep 23 2005 tem Hep Time hh mm ss 12 8 59 IDE Primary Master ST320014A Menu Level Me IDE Primary Slave None IDE Secondary Master None IDE Secondary Slave None Video EGA VGA Halt On All But Keyboard Base Memory 640K Extended Memory 228352 Total Memory 229376 Change the day month year and century TL lt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 3 2 Standard CMOS Features menu Date and Time The Date and Time items show the current date and time held by your PT 8800 If you are running a Windows OS these items are automatically updated whenever you make changes to the Windows Date and Time Properties utility Standard CMOS Features 21 IDE Primary Secondary Master Slave This field is used to configure the IDE hard drive installed in the system Move the cursor to highlight the IDE Pri mary Secondary Master Slave fields and press Enter The IDE Primary Master submenu opens Phoenix AwardBIOS CMOS Setup Utility IDE Primary Master IDE HDD Auto Detection Press Enter tem Help Auto IDE Primary Master Access Mode Auto Menu Level Mi Capacity 20021 MB To auto detect the HDD s size head on this channel Cylinder 38792 Head 16 Precomp 0
28. ESC gt to go back to the main menu Advanced BIOS Features 27 Integrated Peripherals This option defines the operation of peripheral components on the system s input output ports Phoenix AwardBIOS CMOS Setup Utility Integrated Peripherals gt OnChip PCI Device Press Enter SuperlO Device Press Enter Menu Level WM TL lt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 3 6 Integrated Peripherals menu OnChip IDE Device See OnChip IDE Device on page 29 OnChip PCI Device See Onboard Device on page 30 SuperlO Device See SuperlO Device on page 31 28 Chapter 3 BIOS Setup Utility OnChip IDE Device Use this item to enable or disable the PCI IDE channels that are integrated on the mainboard Select the item and press lt Enter gt to open the following menu Phoenix Award WorkstationBIOS CMOS Setup Utility OnChip IDE Device On Chip Primary PCI IDE Enabled Item Help IDE Primary Master PIO Auto IDE Primary Slave PIO Auto Menu Level M IDE Primary Master UDMA Auto IDE Primary Slave UDMA Auto On Chip Secondary PCIIDE Enabled IDE Secondary Master PIO Auto IDE Secondary Slave PIO Auto IDE Secondary Master UDMA Auto IDE Secondary Slave UDMA Auto IDE HDD Block Mode Enabled TL lt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Val
29. Hole At 15M 16M This item can be used to reserve memory space for some ISA expansion cards that require it VGA Setting The following items allow you to configure the settings about On Chip VGA PEG Onchip VGA Control This item allows you to select whether to use the onboard graphics processor or the PCI Express card On Chip Frame Buffer Size This item is used to select the video frame buffer size DMVT Mode Dynamic Video Memory Technology DVMT allows the system to dynamically allocate memory resources according to the demands of the system at any point in time that improves the efficiency of the memory allocated to either system or graphics processor This item allows you to select the DVMT operating mode DMVT FIXED Memory Size This item allows you to set the maximum amount of system memory that can be allocated as graphics memory Boot Display If you connect an external display to this machine you can use this setting to turn off the LCD and only use the external display To use dual displays this must be set to CRT LFP LVDS Panel Number This setting auto detects the panel resolution and other panel settings 20 CHAPTER 2 BIOS SETUP gt PCI Express Boot Port Func Use this item to control the PCI E ports on the mainboard Select the item and press Enter to open the following menu Phoenix AwardBIOS CMOS Setup Utility PCI Express Root Port Func PCI Express Port 1 Item Help PCI Express Port 2 PCI
30. Landing Zone 38791 Sector 63 TL lt Move Enter Select PU PD Value F10 Save ESC Exit Ff1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 3 3 IDE Primary Master Submenu IDE HDD Auto Detection Press Enter while this item is highlighted if you want the Setup Utility to automatically detect and configure a hard disk drive on the IDE channel one line will appear in the parameter box Choose the line that lists LBA for an lp If you are setting up a new hard disk drive that supports LBA mode more than LBA drive NOTE IDE Primary Secondary Master Slave If you leave this item at Auto the system will automatically detect and configure any IDE devices it finds If it fails to find a hard disk change the value to Manual and then manually configure the drive by entering the characteristics of the drive in the fields described below e Capacity displays the capacity of the HDD in megabytes M Cylinder indicates the number of cylinders that the HDD has A cylinder is the sum total of all tracks that are in the same location on every disk surface Head displays the number of heads in the HDD A head is a device that reads and writes data on the hard disk Precomp displays the track where precompensation is initiated Precompensation is a feature whereby the HDD uses a stronger magnetic field to write data in sectors that are closer to the center of the disk In CAV 22 C
31. ME integrated high performance 2D 3D graphics BIOS Award Plug and Play BIOS Supports APM and ACPI Jumper free setting on COM port and cash drawer port voltage selection LCD panel 15 inch TFT high brightness LCD I O support connectors Six RS232 ports 4 with 5v 12vdc power BIOS selection jumper free Two serial pin headers on board 1 for touch 1 for customer display One RJ45 with LEDs Ethernet connector 10 100M 1GHz BASE T One PS 2 keyboard port One PS 2 mouse port One parallel port One type II CF card IDE interface One DB15 VGA port support dual view dual contents display One Cash Drawer port 24Vdc BIOS selection jumper free support 1 address Six 2 0 USB ports 4 standard 2 at the front panel 2 powered USB 12vdc amp 24vdc on rear panel MIC in Line Out One PCI slot Hard drive One 3 5 inch IDE hard drive Touch panel spill proof Spill proof design resistive or capacitive touch screen LED status indicators LED for power and HDD Power supply 220W ATX power supply Mainboard architecture System Board I O Board connected by connector 44 Appendix ITEM Environmental DESCRIPTION Operation temp 5 40 degree C Storage temp 20 60 degree C Humidity Operation 20 85 Storage 5 85 Power Supply One internal 220w full range ATX power supply Options Magnetic card reader 3 tracks Internal Smart Card Reader USB interface Rear Customer Display 2 x 20 VFD type I
32. PT 8800 User manual PIRIVWNER All in one POS Terminal PT 8850 User Manual Copyright This publication including all photographs illustrations and software is protected under international copyright laws with all rights reserved Neither this manual nor any of the material contained herein may be reproduced without written consent of the author Disclaimer The information in this document is subject to change without notice The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes Trademark recognition All product names used in this manual are the properties of their respective owners and are acknowledged Federal Communications Commission FCC This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio
33. PTIONAL CUSTOMER DISPLAY SECOND DISPLAY OPTIONAL THIS USER MANUAL OPTIONAL If any item is missing or appears damaged contact your dealer immediately 2 Chapter 1 Getting Started Identifying components This section describes the parts and connectors on the PT 8800 Front right view o 1 2 LE a Figure 1 2 Front right view of PT 8800 DESCRIPTION 1 15 inch TFT LCD touch screen Smart card reader Speakers Compact Flash card reader Power LED Power button NIOJ oO BY Ww dM Two USB ports Identifying components Rear right view Figure 1 3 Rear right view of PT 8800 DESCRIPTION 1 Customer display cover 2 MSR module 3 Mainboard cover 4 Rear cover 5 Rear cover latches A Chapter 1 Getting Started Rear connectors Figure 1 4 shows the connectors on the rear of the PT 8800 You must remove the rear cover to access the connectors See Removing the rear cover on page 6 Lu 16 15 14 13 12 11 Figure 1 4 Rear connectors labeled DESCRIPTION 1 PS 2 mouse connector 2 Parallel connector 3 COM4 connector 4 Line out 5 Act LED green lights when network activity is detected 6 Link LED orange lights when the network is found 7 COM2 connector 8 RJ 11 cash drawer connector 9
34. Powered USB connector 24V connect peripherals such as USB printers 10 Powered USB connector 12V connect peripherals such as a customer display 11 RJ 45 LAN connector 12 Mic in 13 COM3 connector 14 VGA connector 15 COM1 connector 16 PS 2 keyboard connector Powered USB peripherals have keyed connectors to match the 12V and 24V powered USB connectors on the PT 8800 Do not try to force a 12V connector LI from a peripheral into the 24V connector on the PT 8800 IMPORTANT You can also connect standard USB devices to the powered USB connectors Identifying components 5 For powered USB gt 1 24V cannot exceed 2A lp 2 12V cannot exceed 3A IMPO RTANT 3 Total of 24V amp 12V cannot exceed 48 watts N Plugging a phone line into the LAN port RJ 45 connector can damage the con nector Take care to only plug an RJ 45 connector into the LAN port CAUTION Dy COM 6 is reserved for the optional customer display NOTE Removing the rear cover Refer to the following to remove the rear cover 1 Open the rear cover latches 2 Remove the rear cover 6 Chapter 1 Getting Started When replacing Align the rear cover tab with the open ing on the PT 8800 Adjusting display angles The main display can be tilted back from an upright perpendicular position to about 30 degrees as shown in Figure 1 5 The customer display can be tilted as shown in Figu
35. SC Exit F1 General F6 Fail Safe Defaults F7 Optimized Defaults Figure 3 10 Power Management Setup menu ACPI Function This mainboard supports ACPI Advanced Configuration and Power management Interface Use this item to enable or disable the ACPI feature The default setting is Enabled ACPI is a power management specification that makes hardware status informa tion available to the operating system ACPI enables a PC to turn its peripherals on and off for improved power management It also allows the PC to be turned on and off by external devices so that mouse or keyboard activity wakes up the PT 8800 Power Management This item acts like a master switch for the power saving modes and hard disk timeouts If this item is set to Max Sav ing power saving modes occur after a short timeout If this item is set to Min Saving power saving modes occur after a longer timeout If the item is set to User Define you can insert your own timeouts for the power saving modes The default setting is User Define Video Off Method This item defines how the video is powered down to save power The default setting is V H SYNC Blank Video Off In Suspend This option defines if the video is powered down when the system is put into suspend mode The default setting is Yes Suspend Type If this item is set to the default Stop Grant the CPU will go into Idle Mode during power saving mode Power Management Setup Option 33 MODEM Use IRQ If y
36. T Mode Select This option is used to set the UART mode The default setting is Normal Onboard Parallel Port This option is used to assign the I O address and IRQ for the onboard parallel port Parallel Port Mode Enables you to set the data transfer protocol for the parallel port There are five options SPP Standard Parallel Port EPP Enhanced Parallel Port ECP Extended Capabilities Port ECP EPP and PntMode The default setting is SPP SPP allows data output only Extended Capabilities Port ECP and Enhanced Parallel Port EPP are bi directional modes allowing both data input and output ECP and EPP modes are only supported with EPP and ECP aware peripherals PntMode allows the parallel port to operate in bipoloar mode EPP Mode Select There are two versions of the EPP transfer protocol EPP 1 7 and EPP 1 9 This feature allows you to select the version of EPP that the parallel port should use PWRON After PWR Fail This feature allows you to set the power on action to be taken when the system recovers from a power failure 25 gt USB Device Setting Use this item to change settings for USB devices Select the item and press Enter to open the following menu Phoenix AwardBIOS CMOS Setup Utility SuperIO Device USB 1 0 Controller Item Help USB 2 0 Controller USB Operation Mode USB Keyboard Function USB Mouse Function USB Storage Function Figure 2 12 USB Device Setting submenu t1 Move Enter Select
37. The default setting is Disabled Resume On LAN Use this item to enable LAN activity to wake up the system from a power saving mode The default setting is Dis abled Power On by Ring Use this item to enable modem activity to wakeup the system from a power saving mode Resume by Alarm When set to Enabled the following two fields become available and you can set the date day of the month hour minute and second to turn on your system When set to 0 zero for the day of the month the alarm will power on your system every day at the specified time The default setting is Disabled Date of Month Alarm When set to 0 the system powers on everyday at the time specified in the Time hh mm ss Alarm field Select a date from 1 to 31 for the system to power on at the time specified in the Time hh mm ss Alarm field The default setting is 0 Time hh mm ss Alarm Set the time for the system to power on as defined in the Date of Month Alarm field The time set in this field must be later than the time in the RTC time as shown in the Standard CMOS Features on page 21 Reload Global Timer Events Global Timer power management events are I O events whose occurrence can prevent the system from entering a power saving mode or can awaken the system from such a mode In effect the system remains alert for anything that occurs to a device that is configured as Enabled even when the system is in a power down mode
38. This option displays critical timing parameters of the mainboard Leave the items on this menu at their default settings unless you are very familiar with the technical specifications of your system hardware If you change the values incor rectly you may introduce fatal errors or recurring instability into your system Phoenix Award WorkstationBIOS CMOS Setup Utility Advanced Chipset Features DRAM Timing Selectable By SPD tem Hep CAS Latency Time 25 Active to Precharge Delay 7 Menu Level Me DRAM RAS to CAS Delay 3 DRAM RAS Precharge 3 DRAM Data Integrity Mode Non ECC MGM Core Frequency Auto Max 266MHz System BIOS Cacheable Enabled Video BIOS Cacheable Disabled Memory Hole At 15M 16M Disabled Delayed Transaction Enabled Delay Prior to Thermal 16 Min AGP Aperture Size MB 64 On Chip VGA Setting On Chip Video Enabled On Chip Frame Buffer Size 1MB TL lt Move Enter Select IHPU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 3 5 Advanced Chipset Features menu DRAM Timing Selectable The EEPROM on a memory card has Serial Presence Detect SPD data structure that stores information about the module such as memory size and speed When SPD is selected the CAS Latency Time and Active to Precharge Delay items are set to their defaults and the system runs according to information in the EEPROM providing the mo
39. Veto dr coi ae i ecce Bae td Ta rb aA 28 OnChipADE D6eyice sarr S su eem i Ote edet pee ree RUIT URS 29 Onboard Device x er reete e dete i ter eerie IR eerte iem uq equ 30 SuDeriC Devices eset RERO ORC We enO m RC T BG 31 Power Management Setup Option 15 deris eret t or e Reb ue i Medi retos 32 PnPIPGI Configurations eie ir tea iet e e ra t OR Ru ea Pe eaten 35 PC Health Status rta tnitan re eve ie tette a RE 36 iii Frequency Voltage Control Option 5 eec etus ertectex escis ced erm ec rei is edocet aladdin 37 Other BIOS Options ec ue t pe dette tte te RN ck 38 Load Fail Safe Defaults Option 3 e i ie pea ee eee ee taedis ped rece decem tee a esce Moda 38 Load Optimized Defaults Option seen eene nene eere nn nn eren en ener 38 Set Supervisor and User Passwords Options sese ener 39 Save amp Exit Setup Option e naei i eene eene E A eene ee tenen ren entr enr eere n er ener enne 39 Exit Without Saving 2n tea edle tace tes eee et ode EO Uh dee te e i ere Ee PEDIR CARE bee 40 Kies cup dm LE EE 41 roubleshoOHfiS uu os ots peas ee rai text baie eque ten at ua aensed assit ids LP o Pegbas ek AT aaa AEE a eal ese deba adig 41 Tips for Troubleshooting x tret sedie len i onsite TE es an goto 41 The PowerzOm Self T6st z e ort Ren oT HIP ON etus 41 Beep Errors at POST toe ds dob see tae rmt NI et eds 41 Beep Message Errors at POST sse eene eene eren neret eer enne enne ener nene enne 42 General Problems ein det
40. a 29 Onboard Device enu i ases vete ee eiae dee aa e aduer Mae 30 Super IO Device MEDUS 2er epos eri eit edes deca td aqad scobasde ee las EATER lads 31 Power Management Setup menlis oett eei eren tenda deca dee eu e oie ede ep pa 33 PnP PCI Configurations Meussen aaa ila aay 35 PEHealth Status men ee eee e oe cer a a i ie pee acces MPa 36 Frequency Voltage Control s e Men ee eai ooo ho eed 37 CHAPTER 1 GETTING STARTED This chapter describes the procedures from unpacking the PT 8800 POS to powering it on The following topics are described Unpacking the PT 8800 Checking the package contents on page 2 dentifying components on page 3 Removing the rear cover on page 6 Adjusting display angles on page 7 Setup considerations on page 7 Connecting peripheral devices on page 8 Powering the PT 8800 on and off on page 9 Unpacking the PT 8800 The PT 8800 and cable accessories are packed in a cardboard carton with foam padding for protection during shipping Figure 1 1 Unpacking the PT 8800 Carefully unpack the PT 8800 and keep the packing materials If you need to ship the PT 8800 in the future repack it as shown in Figure 1 1 Checking the package contents After you unpack the PT 8800 check that the following items are included PT 8800 SOME UNITS SHIP WITH CUSTOMER POWER CABLE DRIVER CD ROM WITH DISPLAY AND MSR INSTALLED DRIVERS AND USER MANUAL PDF PT 8800 MSR O
41. ad and writes per sector that the drive can support and improves the speed of access to IDE devices IDE DMA Transfer Access This BIOS feature allows you to enable or disable DMA Direct Memory Access support for all IDE devices If you disable this BIOS feature the BIOS will disable DMA transfers for all IDE drives They will revert to PIO mode transfers If you enable this BIOS feature the BIOS will enable DMA transfers for all IDE drives The proper DMA mode will be detected at boot up If the drive does not support DMA transfers then it will use PIO mode instead It is highly recommended that you leave this BIOS feature at the default setting of Enabled If the drive supports DMA transfers the proper DMA transfer mode will be enabled for that drive allowing it to burst data at anywhere from 33MB s to 133MB s depending on the transfer mode supported IDE Primary Secondary Master Slave PIO Each IDE channel supports a master device and a slave device These items let you assign which kind of PIO Programmed Input Output is used by IDE devices Choose Auto to let the system auto detect which PIO mode is best or select a PIO mode from 0 4 IDE Primary Secondary Master Slave UltraDMA Each IDE channel supports a master device and a slave device This mainboard supports UltraDMA technology which provides faster access to IDE devices If you install a device that supports UltraDMA change the appropriate item on this list to Auto You ma
42. arted This section covers unpacking and checking the package contents and identifying components Information on connecting peripheral devices and powering on is also provided Chapter 2 BIOS Setup Utility The BIOS chapter provides information on navigating and changing settings in the BIOS Setup Utility Chapter 3 Upgrading Components This section provides information on upgrading components Appendix The appendix covers troubleshooting information on having the PT 8850 serviced and technical specifications Safety information Before installing and using the PT 8850 POS take note of the following precautions Read all instructions carefully Do not place the unit on an unstable surface cart or stand Do not block the slots and opening on the unit which are provided for ventilation Do not push objects in the ventilation slots as they may touch high voltage components and result in shock and damage to the components Only use the power source indicated on the marking label If you are not sure contact your dealer or the Power Company The unit uses a three wire ground cable which is equipped with a third pin to ground the unit and prevent electric shock Do not defeat the purpose of this pin If your outlet does not support this kind of plug contact your electrician to replace your obsolete outlet Do not place anything on the power cord Place the power cord where it will not be in the way of foot traffic Follow all
43. ault setting is Auto DRAM Data Integrity Mode Set the DRAM Data Integrity Mode The default setting is NON ECC MGM Core Frequency Set the MGM Core Frequency The default setting is AUTO MAX266 System Video BIOS Cacheable These items allow the video and or system to be cached in memory for faster execution We recommend that you leave these items at the default value The default setting is Disabled Memory Hole at 15M 16M This item can be used to reserve memory space for some ISA expansion cards that require it The default setting is Dis abled Delayed Transaction The chipset has an embedded 32 bit posted write buffer to support delay transactions cycles Enable this item to sup port compliance with PCI specification version 2 1 The default setting is Enabled Delay Prior to Thermal Set the Delay Prior to Thermal The default setting is 16 min AGP Aperture Size MB This item defines the size of the aperture if you use an AGP graphics adapter The AGP aperture refers to a section of the PCI memory address range used for graphics memory We recommend that you leave this item at the default set ting The default setting is 64 On Chip Video This item is used to enable or disable the onboard video The default setting is Enabled On Chip Frame Buffer Size This item is used to select the video frame buffer size The default setting is IMB After you have made your selections in the Advanced Chipset Features menu press lt
44. ave the PT 8850 serviced HDD reset failed Have the PT 8850 serviced HARD DISK S FAIL 80 HDD controller diagnostics Have the PT 8850 serviced failed HARD DISK S FAIL 40 HARD DISK S FAIL 20 HDD initialization error Have the PT 8850 serviced HARD DISK S FAIL 10 Unable to recalibrate fixed disk Have the PT 8850 serviced The keyboard is locked and the key board controller is pulled Have the PT 8850 serviced low KEYBOARD IS LOCKED OUT UNLOCK THE KEY Make sure the keyboard is KEYBOARD ERROR OR NO KEYBOARD PRESENT A keyboard is not detected attached correctly and no key is pressed during boot System keeps rebooting because i5 QE LOSI the keyboard controller is pulled Have the PT 8850 serviced low for testing purposes BIOS ROM CHECKSUM ERROR SYSTEM HALTED The ROM address is incorrect Have the PT 8850 serviced The memory card is not MEMORY TEST FAIL correctly installed or is Have the PT 8850 serviced damaged 44 APPENDIX General Problems Refer to the following general problems you may encounter PROBLEM SOLUTION The display screen is dark Make sure that the PT 8850 is not in suspend mode An incorrect date and time are displayed Correct the date and time using the DOS DATE and TIME commands or the options in the Setup Utility You can also set the date and time in Windows by double clicking the clock
45. by discharges of static electricity Working on computers that are still connected to a power supply can be extremely dangerous Follow these guidelines to avoid damage to the computer or injury to yourself Always disconnect the unit from the power outlet Leave all components inside the static proof packaging that they ship with until they are ready for installation e After replacing optional devices make sure all screws springs or other small parts are in place and are not left loose inside the case Metallic parts or metal flakes can cause electrical shorts unauthorized servicing is not covered by the warranty If you are not confident of carrying out installation procedures we recommend that you refer the job to CAUTION qualified personnel i Only qualified personnel should perform repairs on the PT 8800 Damage due to AN If the LCD breaks and fluid gets onto your hands or into your eyes immediately wash with water and seek medical attention WARNING connected to the PT 8800 Unplug the power cord before attempting to replace 5 The inverter card has high voltage Do not touch the inverter card while power is WARNING 27 Part tively discharge any static electricity by touching the bare metal chassis of the 4 To prevent static damage to components wear a grounded wrist strap Alterna unit case or the bare metal body of any other grounded appliance CAUTION ll on the board unless
46. communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment onto an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Shielded interconnect cables and a shielded AC power cable must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device Changes or modifications not expressly approved by the system s manufacturer could void the user s authority to operate the equipment Declaration of conformity This device complies with part 15 of the FCC rules Operation is subject to the following conditions This device may not cause harmful interference and This device must accept any interference received including interference that may cause undesired operation About this manual This manual is intended for system administrators who are familiar with setting up a new system and installing an operating system The manual consists of the following sections Chapter 1 Getting St
47. connector can damage the con CAUTION nector Take care to only plug an RJ 45 connector into the LAN port Revision history Version 1 01 April 2006 TABLE OF CONTENTS Chapter 1 nubis Hr l Unpacking the 1589300 inei e a pus bon E a N 1 Checking the package contents su cp esteem es nt dec en uto artnet ats Du S SN I eet emt os 2 Identifying components 15 5 henro ete aa aao aaa aae lea ee hsc tea A Coates e luu ncs dois Pate aud 3 Frontzriglt view s e bo ne e E t ep edt e d eta merito ofa ent tots du ees 3 Rearzright View cdi od eie RE enn eu 4 Rear ConhectoEs c aie cie te tecto ed te on ee Ce e RE RR REPE EORR NER RAT AEA AEG AG UR ade ds 5 Removing the feat COVER ux roseo Ub Ed NIE NM rdi Ie p REIN Lx Real at a a age deett d 6 Adj stine display angles Arae tees rent tret ermita N Yo R A eae o ase n etui Cate 7 Set p COHSIde AMONG ax ciated dpa doe p ttal team Oe e eec ceste MEL Uer etaed 7 Connecting peripheral devices eas sd tustcde ein e euch ath ad dot ia e atria pA cie diss uad 8 Connecting a cash draw er oet esti de c e du tpe S e UE Y ed as QU EO a des 8 Powernne the PT 8800 on and Off 2rd Monate e ba vod cota to eau eed ano ed cs ea Re eb Ru oa d qu aS nba 9 Chapter 2 Upgrading Components cue ettet aad eon CH oc br esee nian Ue e BUD TA NI enone easel 11 Safety and DISCAULIOTIS a sessstevaesdcessazees acetates te eor e End AE ETENA ERE x DUE a add Erata favo daia iata 11 Before you begit nae deed obe toes qucd
48. ctory setting is None The voltage for the COM ports is set at None at the factory However for example to provide power to an installed customer display this setting must be set at 12V for the corresponding COM port For a 5V IMPORTANT device such as a barcode scanner the setting should be 5V Onboard Serial Port 3 4 5 6 These items allow you to select an address for the third and fourth serial ports Serial Port 3 4 5 6 Use IRQ These items allow you to select an corresponding interrupt for the third and fourth serial ports 22 CHAPTER 2 BIOS SETUP gt OnChip IDE Device Use this item to enable or disable the PCI IDE channels that are integrated on the mainboard Select the item and press Enter to open the following menu Phoenix AwardBIOS CMOS Setup Utility OnChip IDE Device IDE HDD Block Mode Item Help IDE DMA transfer access IDE Primary Master PIO IDE Primary Slave PIO IDE Primary Master UDMA IDE Primary Slave UDMA OnChip Secondary PCI IDE IDE Secondary Master PIO Figure 2 10 OnChip IDE IDE Secondary Slave PIO A IDE Secondary Master UDMA Device submenu IDE Secondary Slave UDMA SATA Mode LEGACY Mode Support t12 Move Enter Select PU PD Value F10 Save ESC Exit Fl General Help F5 Previous Values F6 Fail Safe Defaults F7 0ptimized Defaults IDE HDD Block Mode Enable this field if the IDE hard drive supports block mode Block mode enables BIOS to automatically detect the optimal number of block re
49. d 42 MEMORY TEST FAIL Appendix The memory card is not correctly installed or is damaged Have the PT 8800 serviced General Problems PROBLEM The display screen is dark Refer to the following general problems you may encounter SOLUTION Adjust the screen brightness Make sure that the PT 8800 is not in suspend mode An incorrect date and time are displayed Correct the date and time using the DOS DATE and TIME commands or the options in the Setup Utility You can also set the date and time in Windows by double clicking the clock on the task bar or in the control panel If the date and time become incorrect after a short time the CMOS battery may be depleted Replace the battery The following message appears at boot up Invalid system disk Replace the disk and then press any key You hear irregular beeps during operation of the computer and the system halts Ensure that an operating system is installed Check the boot sequence in the BIOS setup utility Have the PT 8800 serviced An unidentified message is displayed Reboot the computer and run the BIOS Setup Utility Con firm the Setup Utility parameters If the same message is displayed after booting up again have the PT 8800 ser viced You cannot operate the printer You cannot use a mouse or keyboard Check the printer cable connection Ensure that the printer power switch is turned on
50. d as shown in Figure 1 6 Figure 1 5 Adjusting the display Figure 1 6 Adjusting the customer display Setup considerations When setting up the machine consider the following Usea desktop or counter that is stable and even Ensure there is enough room around the sides and rear of the machine for ventilation Ensure there is room to connect cables and that cables are long enough to reach peripheral devices or a power outlet Connecting peripheral devices Peripheral devices such as a printer or scanner can be connected to the machine Refer to the user manual of the device you are connecting for instructions on installing drivers where needed Remove the rear cover to access the connectors See Removing the rear cover on page 6 e 9 Amplifier or speakers Headphones COM4 COM2 Cashdrawer ES 69 COM1 l COM3 UN cC Powered USB he Mouse Printer SF Compliant pos devices 24V a m Oy 24V J ADSL modem Keyboard Monitor or router Powered USB Compliant devices 12V Microphone Figure 1 7 Connecting peripheral devices N Do not plug a phone line into the RJ 45 ADSL or router connector Doing so can damage the connector CAUTION Connecting a cash drawer Refer to the following to connect a cash drawer 2 The cash drawer RJ 11 connector is DC 24V Ensure the cash drawer lp to be connected matches this power specification
51. d then opening up the IRQ Resources sub menu PCI VGA Palette Snoop This item is designed to overcome some problems that can be caused by some non standard VGA cards This mainboard includes a built in VGA system that does not require palette snooping so you must leave this item disabled INT Pin 1 2 3 4 5 6 7 8 Assignment These item allow you change the INT pin assignment Maximum Payload Size This feature determines the maximum TLP Transaction Layer Packet payload size that can be supported by the motherboard chipset s PCI Express controller The TLP payload size determines the amount of data transmitted within each data packet 29 gt IRQ Resources This menu can only be accessed when the Resources Controlled by menu is set to Manual In the IRQ Resources sub menu if you change any of the IRQ assignations to Legacy ISA then that Interrupt Request Line is reserved for a legacy ISA expansion card Press lt Esc gt to close the IRQ Resources sub menu Phoenix AwardBIOS CMOS Setup Utility IRQ Resources assigned to assigned to assigned to assigned to assigned to assigned to assigned to assigned to Figure 2 15 IRQ Resources assigned to submenu assigned to tj Move Enter Select PU PD Value F10 Save ESC Exit Fl General Help F5 Previous Values F6 Fail Safe Defaults F7 0ptimized Defaults 30 CHAPTER 2 BIOS SETUP PC Health Status On mainboards that support hardware monitoring this item lets you moni
52. e default setting The default setting is Fast Typematic Rate Setting If this item is enabled you can use the following two items to set the typematic rate and the typematic delay settings for your keyboard The default setting is Disabled Typematic Rate Chars Sec Use this item to define how many characters per second are generated by a held down key The default setting is 6 Typematic Delay Msec Use this item to define how many milliseconds elapse before a held down key begins generating repeat characters The default setting is 250 Security Option If you have installed password protection this item defines if the password is required at system start up or if it is only required when a user tries to enter the Setup Utility The default setting is Setup OS Select For DRAM gt 64 MB This item is only required if you have installed more than 64 MB of memory and you are running the OS 2 operating system Otherwise leave this item at the default The default setting is Non OS2 Report No FDD For WIN 95 If you are running a system with no floppy drive and using Windows 95 select Yes for this item to ensure compatibil ity with the Windows 95 logo certification Otherwise select No The default setting is No Small Logo EPA Show Determines whether the EPA logo appears during boot up The default setting is Enabled Press lt Esc gt to return to the main menu Advanced BIOS Features 25 Advanced Chipset Features
53. e unit from the power outlet Leave all components inside the static proof packaging that they ship with until they are ready for instal lation After replacing optional devices make sure all screws springs or other small parts are in place and are not left loose inside the case Metallic parts or metal flakes can cause electrical shorts A CAUTION x A CAUTION Only qualified personnel should perform repairs on the PT 8850 Damage due to unauthorized servicing is not covered by the warranty If you are not confident of installing a hard drive or CompactFlash card we recommend that you refer the job to qualified personnel If the LCD breaks and fluid gets onto your hands or into your eyes immediately wash with water and seek medical attention The inverter card has high voltage Do not touch the inverter card while power is connected to the machine Unplug the power cord before attempting to replace any part To prevent static damage to components wear a grounded wrist strap Alternatively discharge any static electricity by touching the bare metal chassis of the unit case or the bare metal body of any other grounded appliance 35 components on the board unless it is necessary to do so Do not flex or stress the circuit board Do not hold components such as a processor CAUTION by its pins hold it by the edges t Hold electronic circuit boards by the edges only Do not touch the Before you begin
54. eads and writes data on the hard disk Precomp displays the track where precompensation is initiated Precompensation is a feature whereby the HDD uses a stronger magnetic field to write data in sectors that are closer to the center of the disk In CAV recording in which the disk spins at a constant speed the sectors closest to the spindle are packed tighter than the outer sectors Landing Zone displays the location of the safe non data area on a hard disk that is used for parking the read write head Sector displays the number of sectors available on the HDD A sector is the smallest unit of storage space on a disk Access Mode This item defines special ways that can be used to access IDE hard disks such as LBA Large Block Addressing Leave this value at Auto and the system will automatically decide the fastest way to access the hard disk drive 15 Advanced BIOS Features Selecting Advanced BIOS Features on the main menu opens up this screen Phoenix AwardBIOS CMOS Setup Utility Advanced BIOS Features gt CPU Feature Item Help gt Hard Disk Boot Priority Virus Warning CPU L1 amp L2 Cache CPU L3 Cache Quick Power On Self Test First Boot Device Second Boot Device Third Boot Device Figure 2 4 Advanced BIOS Boot Other Device Features menu Security Option APIC Mode Small Logo EPA Show t1 Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe De
55. ed BIOS Features Load Fail Safe Defaults Advanced Chipset Features Load Optimized Defaults integrated Peripherals Set Supervisor Password Power Management Setup Set User Password WPnP PCI Configurations Save amp Exit Setup PC Health Status Exit Without Saving Esc Quit Tl Select item F10 Save amp Exit Setup Time Date Hard Disk Type Load Fail Safe Defaults Option This option opens a dialog box that lets you load fail safe defaults for all appropriate items in the Setup Utility Follow these instructions 1 From the main menu scroll to Load Fail Safe Defaults 2 Press Enter to open the Load Setup Fail Safe Defaults menu 3 Press Y 4 Press Enter to load the defaults The fail safe defaults place no great demands on the system and are generally stable If your system is not functioning correctly try loading the fail safe defaults as a first step in getting your system working properly again If you only want to load fail safe defaults for a specific option select and display that option and then press F6 Load Optimized Defaults Option This option opens a dialog box that lets you load optimized defaults for all appropriate items in the Setup Utility Follow these instructions 1 From the main menu scroll to Load Optimized Defaults 2 Press lt Enter gt to open the Load Optimized Defaults menu 3 Press Y 4 Press Enter to load the defaults The optimized defaults place d
56. einstall the operating system and power on the PT 8850 Audio problems Ensure the audio cable is not defective The mute is off 45 Having the PT 8850 Serviced If you are unable to solve the problem you should have the terminal serviced Pack the terminal in the original carton See Unpacking the PT 8850 on page 1 Include a description of the problem and a checklist of the steps you took when trying to fix the problem The information may be useful to the service personnel Return the terminal to the place you purchased it 46 APPENDIX Specifications 15 XGA Color TFT LCD Resolution 1024 x 768 LCD Touch 5 wire Resistive touch RS 232 interface Intel Core 2 Duo Processor E6400 2 13GHz FSB 1066MHz L2 cache 2MB TDP 65W CRU Pentium Dual core Processor E2160 1 80GHz FSB 800MHz L2 cache 1MB TDP 65W Celeron Processor 440 2 0GHz FSB 800MHz L2 cache 512KB TDP 35W NB Intel LE82Q965 Chipset SB Intel FW82801HB Memory 200 pin DDR2 SO DIMM x 2 Systme ships with 1G as the standard BIOS Award System BIOS 4M bits flash ROM Integrated GMA 3000 shared video memory E On board LVDS connector for LCD support P Max shared memory of 128MB default 16MB Dual Display support dual view dual contents Ethernet 10 100 1000 On Board Ethernet controller Audio Realtek 6 Channel High Definition Audio Codecs HDD amp Storage T O Interface Internal 3 5 type SATA HDD
57. em from a power saving mode Resume by Alarm When set to Enabled the following two fields become available and you can set the date day of the month hour minute and second to turn on your system When set to 0 zero for the day of the month the alarm will power on your system every day at the specified time Date of Month Alarm When set to 0 the system powers on everyday at the time specified in the Time hh mm ss Alarm field Select a date from to 31 for the system to power on at the time specified in the Time hh mm ss Alarm field Time hh mm ss Alarm Set the time for the system to power on as defined in the Date of Month Alarm field The time set in this field must be later than the time in the RTC time as shown in the Standard CMOS Features on page 9 Reload Global Timer Events Primary IDEO0 1 When the primary master HDD is working the system timer will be re loaded and the system will not go into suspend mode Secondary IDEO0 1 When the primary master HDD is working the system timer will be re loaded and the system will not go into suspend mode PCI PIRQ A D When the PCI PIRQ A D has been alerted the system timer will be re loaded and the system will not go into suspend mode 28 CHAPTER 2 BIOS SETUP PnP PCI Configurations This option configures how PnP Plug and Play and PCI expansion cards operate in the system Both the ISA and PCI buses on the mainboard use system IRQs
58. emands on the system that may be greater than the performance level of the compo nents such as the CPU and the memory You can cause fatal errors or instability if you load the optimized defaults 38 Chapter 3 BIOS Setup Utility when your hardware does not support them If you only want to load Setup defaults for a specific option select and display that option and then press F7 Set Supervisor and User Passwords Options These items can be used to install a password A Supervisor password takes precedence over a User password and the Supervisor can limit the activities of a User To install a password follow these steps l 2 Highlight the item Set Supervisor User Password on the main menu and press Enter The password dialog box appears Enter Password If you are installing a new password type in the password You cannot use more than eight characters or numbers The Set Supervisor User Password item differentiates between upper and lower case characters Press lt Enter gt after you have typed in the password If you are deleting a password that is already installed press Enter when the password dialog box appears You see a message that indicates that the password has been disabled PASSWORD DISABLED Press any key to continue Press any key You are prompted to confirm the password Confirm Password Type the password again and press Enter or press Enter if you are dele
59. eode d a a lec diss eel a a a od 12 Installing a hard disk drive HDD 2 iae dite bh OQ tei eel tates eum dace ay 12 Installing optional ATS Ia Sos oe ens ofa hoi ette wines Revers atre e he S ssesa y on den pscE 13 Removing the mainboard cover and customer display cover sse 13 Mainboard reference vs diei teet ee e tn cin ient 14 Attaching the customer displaye creses uin ri n e tet e E De uit n uito 15 Attaching the second display iss s RR ERU PARES EET ERIT E 16 Installing a CompactFlash Card 52i desc den m Eds eet Rede cn dem baec ad e Oe in EI QS 17 Anstallino a BOT eat mainai sna obese ptas be PARU balia pa tet ea P e tU espe RR A e i 18 Chapter 3 BIOS Setup py ur aetas nad dapi neben up eretebite Petition sade tue E qeu ie hal ERT 19 PLDOUt TG Setup DI so sg booa rip ee cR cb pen mp quts E A eec pst thiet 19 Entering the Setup Utility s s i e e eH Te IE E DOE reti NR OC SEO TY Cd a RE PEE ta et 20 BIOS NGVICAUON Keys Sassari S PPAR IEEE ESI DU Od dede eise ose desee hes tardies a tine ERES 20 LU sing3BIQONS sew ten qa ETT EO ted Po RN egt ta tane eam 21 Standard CMOS Features morresi reiii n eere Ua ec Nee a e eek stu ania dete tabe du v a vede dite qu du a 2 IDE Primary Secondary Master Slave sss eene en eren nennen eene nnne 22 Advanced BIOS Bedttes i ied oae aR easi et it aa cre veru sb oC e Pra ab dn 24 Advanced Chipset Features 5 eR Rp eR REN NIRE 26 Integrated Peripherals iu cioe tei oet sed rau
60. er On by Ring USB KB Wake Up From S3 Resume by Alarm Primary IDE 0 Primary IDE 1 Secondary IDE 0 Secondary IDE 1 PCI PIRQ A D Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 0ptimized Defaults ACPI Function This mainboard supports ACPI Advanced Configuration and Power management Interface Use this item to enable or disable the ACPI feature ACPI is a power management specification that makes hardware status information available to the operating system ACPI enables a PC to turn its peripherals on and off for improved power management It also allows the PC to be turned on and off by external devices so that mouse or keyboard activity wakes up the machine ACPI Suspend Type Use this item to define how the system suspends In the default S1 POS the suspend mode is equivalent to a software power down If you select S3 STR the suspend mode is a suspend to RAM the system shuts down with the exception of a refresh current to the system memory Run VGABIOS if S3 Resume When the ACPI Suspend Type is set S3 STR this item enables the BIOS to run the VGA BIOS when the system resumes from S3 Power Management This item acts like a master switch f or the power saving modes and hard disk timeouts If this item is set to Max Saving power saving modes occur after a short timeout If this item is set to Min Saving power saving modes occur after a longer time
61. er gt to open the following menu Phoenix AwardBIOS CMOS Setup Utility Onboard Device USB Controller Enabled o emm USB 2 0 Controller Enabled USB Keyboard Support Enabled Menu Level AC97 Audio Auto Init Display First Onboard AGP TL lt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 3 8 Onboard Device menu USB Controller Set this item to Enabled to use USB 1 1 devices The default setting is Enabled USB 2 0 Controller Set this item to Enabled to use USB 2 0 When set to Disabled USB 1 1 devices can still be used The default setting is Enabled USB Keyboard Support Enable this item if you plan to use a keyboard connected through the USB port in a legacy operating system such as DOS that does not support Plug and Play This field can only be configured if the USB Controller field is enabled The default setting is Disabled AC97 AUDIO Enables and disables the onboard audio chip Disable this item if you are going to install a PCI audio add in card The default setting is Auto Init Display First Use this item to specify whether your graphics adapter is installed in the PCI slot or is integrated on the mainboard The default setting is Onboard AGP 30 Chapter 3 BIOS Setup Utility SuperlO Device Use this item to change settings for I O devices Select the item and press Enter to open the following
62. faults F7 0ptimized Defaults Virus Warning When enabled this item provides protection against viruses that try to write to the boot sector and partition table of the hard disk drive You need to disable this item when installing an operating system We recommend that you enable anti virus protection as soon as you have installed an operating system CPU L1 amp L2 Cache All processors that can be installed in this mainboard use internal level 1 L1 and external level 2 L2 cache memory to improve performance CPU L3 Cache All processors that can be installed in this mainboard use external level 3 L3 cache memory to improve performance Quick Power On Self Test Enable this item to shorten the power on testing POST and have the system start up faster You can enable this item after you are confident that the system hardware is operating smoothly First Second Third Boot Device The BIOS loads the operating system from the disk drives in the sequence selected in these three fields Boot Other Device When enabled the system searches all other possible locations for an operating system if it fails to find one in the devices specified under the First Second and Third boot devices Boot Up Numlock Status This field is used to select power on state for NumLock 16 CHAPTER 2 BIOS SETUP Security Option Select whether the password is required every time the system boots or only when you enter setup Option Description S
63. hapter 3 BIOS Setup Utility recording in which the disk spins at a constant speed the sectors closest to the spindle are packed tighter than the outer sectors e Landing Zone displays the location of the safe non data area on a hard disk that is used for parking the read write head Sector displays the number of sectors available on the HDD A sector is the smallest unit of storage space on a disk Access Mode This item defines special ways that can be used to access IDE hard disks such as LBA Large Block Addressing Leave this value at Auto and the system will automatically decide the fastest way to access the hard disk drive Press lt Esc gt to close the IDE device menu and return to the Standard CMOS Features menu Video EGA VGA This item defines the video mode of the system This mainboard has a built in VGA graphics system you must leave this item at the default setting Halt On All But Keyboard This item defines the operation of the system POST Power On Self Test routine You can use this item to select which types of errors in the POST are sufficient to halt the system Base Memory Extended Memory and Total Memory These items are automatically detected by the system at start up time These are display only fields You cannot make changes to these fields Base Memory This field displays the amount of conventional memory detected by the system during boot Extended Memory This field displays
64. he errors that display s WARNING tions ERROR MESSAGE CMOS BATTERY HAS FAILED CAUSE The CMOS battery is depleted The system uses a 3V CR2032 battery CMOS battery mounted on the main board to keep time There is a risk of explosion if the wrong battery type is used when replacing Dispose of used batteries according to local ordinance regula SOLUTION Replace the battery CMOS CHECKSUM ERROR The battery may be weak The CMOS may be corrupt Replace the battery Have the PT 8800 serviced HARD DISK S FAIL 80 HDD reset failed Have the PT 8800 serviced HDD controller diagnostics failed Have the PT 8800 serviced HARD DISK S FAIL 40 HARD DISK S FAIL 20 HDD initialization error Have the PT 8800 serviced HARD DISK S FAIL 10 Unable to recalibrate fixed disk Have the PT 8800 serviced KEYBOARD IS LOCKED OUT UNLOCK THE KEY The keyboard is locked and the key board controller is pulled low Have the PT 8800 serviced KEYBOARD ERROR OR NO KEYBOARD PRESENT A keyboard is not detected Make sure the keyboard is attached correctly and no key is pressed during boot MANUFACTURING POST LOOP System keeps rebooting because the keyboard controller is pulled low for test ing purposes Have the PT 8800 serviced BIOS ROM CHECKSUM ERROR SYSTEM HALTED The ROM address is incorrect Have the PT 8800 service
65. he power outlet 3 Remove the two thumbscrews 4 Remove the mainboard cover 5 Bow the cover up slightly to release the two tabs 6 Remove the customer display cover 38 CHAPTER 3 UPGRADING COMPONENTS When replacing Align the customer display cover tabs with the openings on the machine 7 Pass the cable through the opening in the machine 8 Align the tabs on the customer display with the openings on the machine 9 Slide the customer display into place 10 Connect the customer display cable to CN15 on the mainboard 11 Secure the display with the supplied screw 12 Replace the mainboard cover To supply power to the customer display the COMG voltage is factory set to DC 12V 39 Attaching the second display Refer to the following to attach the second display 1 Turn off the machine properly through the operating system 2 Disconnect the power cord from the power outlet 3 Remove the two thumbscrews 4 Remove the mainboard cover 5 Bow the cover up slightly to release the two tabs 6 Remove the customer display cover 40 CHAPTER 3 UPGRADING COMPONENTS 7 Remove the two thumbscrews 8 Remove the I O board 9 Pass the display cables through the indicated opening 10 Secure the display bracket with the four supplied screws 41 11 Put the bracket cover on
66. ickly Try to pin point the problem and thus avoid replacing non defective parts For example if you replace batteries and the problem remains put the original batteries back and go to the next step Keep a record of the steps you take when troubleshooting The information may be useful when calling for technical support or for passing on to service personnel Use some other electrical device to confirm that the electrical outlet is working Ensure all connections are securely attached The Power On Self Test The Power On Self Test POST runs every time you turn on or reset the computer The POST checks memory the mainboard the display the keyboard the disk drives and other installed options If failure is detected in an area other than the mainboard such as the keyboard or an adapter card an error message is displayed on the screen and testing 1s stopped If your system does not successfully complete the POST but displays a blank screen have the PT 8800 serviced Beep Errors at POST There are two kinds of beep codes in the BIOS e Video error a single long beep followed by three short beeps indicates a video error the screen can not be ini tialized and no information can be displayed e DRAM error a single long beep indicates that a DRAM error has occurred 41 Beep Message Errors at POST If the BIOS detects an error during the POST a message is displayed Refer to the following table for a list of t
67. it is necessary to do so Do not flex or stress the circuit board Do not hold components such as a processor by its pins hold it by the CAUTION edges i Hold electronic circuit boards by the edges only Do not touch the components Before you begin Make sure you have a stable clean working environment Dust and dirt can get into components and cause a malfunc tion Adequate lighting and proper tools can prevent you from accidentally damaging the internal components Most of the electrical and mechanical connections can be disconnected by using your fingers It is recommended that you do not use needle nosed pliers to disconnect connectors as these can damage the soft metal or plastic parts of the connectors clean and flat N To prevent scratching the case of the PT 8800 make sure the worktop surface is CAUTION Installing a hard disk drive HDD Refer to the following to install a HDD 1 Remove the rear cover See Removing the rear cover on page 6 2 Remove the two thumbscrews 3 Remove the hard drive bracket 4 Place the new hard drive in the bracket 5 Secure the hard drive with four screws 6 Connect the two cables 7 Replace the hard drive bracket 8 Replace the two thumbscrews 12 Chapter 2 Upgrading Components lp Refer to the documentation with the hard drive for instructions on setting drive jumpers and formatting the drive NOTE Installing
68. ithout Saving Esc Quit TLi Selectitem F10 Save amp Exit Setup Time Date Hard Disk Type Figure 3 1 Main BIOS menu BIOS navigation keys The BIOS navigation keys are listed below KEY FUNCTION c Scrolls through the items on a menu PU PD Modifies the selected field s values Esc Exits the current menu F1 Displays a screen that describes all key functions F5 Loads previously saved values to CMOS F6 Loads a minimum configuration for troubleshooting F7 Loads an optimum set of values for peak performance F10 Saves the current configuration and exits Setup Shift F2 Changes the color of the BIOS menu 20 Chapter 3 BIOS Setup Utility Using BIOS When you start the Setup Utility the main menu appears The main menu of the Setup Utility displays a list of the options that are available A highlight indicates which option is currently selected Use the cursor arrow keys to move the highlight to other options When an option is highlighted execute the option by pressing Enter Some options lead to pop up dialog boxes that prompt you to verify that you wish to execute that option Other options lead to dialog boxes that prompt you for information Some options marked with a triangle P lead to submenus that enable you to change the values for the option Use the cursor arrow keys to scroll through the items in the submenu Standard CMOS Features Selecting Standard
69. ment to ensure compli ance with the pertinent RF emission limits governing this device Changes or modifications not expressly approved by the system s manufacturer could void the user s authority to operate the equipment Declaration of conformity This device complies with part 15 of the FCC rules Operation is subject to the following conditions This device may not cause harmful interference and This device must accept any interference received including interference that may cause undesired operation About this manual This manual is intended for system administrators who are familiar with setting up a new system and installing an operating system The manual consists of the following sections Chapter 1 Getting Started This section covers unpacking and checking the package con tents and identifying components Information on connecting peripheral devices and powering on is also provided Chapter 2 Upgrading Components This section provides information on upgrading components such as a hard disk drive or CompactFlash card reader Chapter 3 BIOS Setup Utility The BIOS chapter provides information on navigating and chang ing settings in the BIOS Setup Utility Appendix The appendix covers troubleshooting information on having the PT 8800 serviced and technical specifications Safety information Before installing and using the PT 8800 POS take note of the following precautions Read all instructions carefull
70. ntegrated second screen Supported operating systems DOS Windows95 98 2000 ME XP XPe Linux Safety and EMI CE FCC VCCI Specifications 45 46 Appendix
71. ou want an incoming call on a modem to automatically resume the system from a power saving mode use this item to specify the interrupt request line IRQ that is used by the modem You might have to connect the fax modem to the mainboard Wake On Modem connector for this feature to work The default setting is 3 Suspend Mode The CPU clock will be stopped and the video signal will be suspended if no Power Management events occur for a specified length of time Full power function will return when a Power Management event is detected Options are from 1 Min to 1 Hour and Disabled The default setting 1s Disabled HDD Power Down The IDE hard drive will spin down if it is not accessed within a specified length of time Options are from 1 Min to 15 Min and Disabled The default setting is 15 Min Soft Off by PWR BTN Under ACPI Advanced Configuration and Power management Interface you can create a software power down In a software power down the system can be resumed by Wake Up Alarms This item lets you install a software power down that is controlled by the normal power button on your system If the item is set to Instant Off then the power but ton causes a software power down If the item is set to Delay 4 Sec then you have to hold the power button down for four seconds to cause a software power down The default setting is Instant Off Wake Up by PCI card Use this item to enable PCI activity to wake up the system from a power saving mode
72. out If the item is set to User Define you can define timeouts for the power saving modes Video Off Method This item defines how the video is powered down to save power Video Off In Suspend This option defines if the video is powered down when the system is put into suspend mode 27 Suspend Type This option defines the suspend type for the video MODEM Use IRQ This option sets the IRQ for the modem chip Suspend Mode The CPU clock will be stopped and the video signal will be suspended if no Power Management events occur for a specified length of time Full power function will return when a Power Management event is detected HDD Power Down The IDE hard drive will spin down if it is not accessed within a specified length of time Soft Off by PWR BTN Under ACPI Advanced Configuration and Power management Interface you can create a software power down In a software power down the system can be resumed by Wake Up Alarms This item lets you install a software power down that is controlled by the normal power button on your system If the item is set to Instant Off then the power button causes a software power down If the item is set to Delay 4 Sec then you have to hold the power button down for four seconds to cause a software power down Power On by Ring Use this item to enable modem activity to wakeup the system from a power saving mode USB KB Wake Up From S3 Use this item to enable USB keyboard to wakeup the syst
73. rading the hard drive tert tta bet eet eee 37 Installing optional displays ss mm 38 Attaching the second display seccion n nnrnn n na 40 Installing PCIFE X1 Catd iuuiec eite erede terne ete 42 APRENDIX e T c 43 Troubleshooting rto i EE deem Erat tote e dees 43 Tips for Troubleshooting crc ett t oer dr eee ees 43 The Power On Self Test renti prie Ra RR ER ERREAA 43 Beep Emors at POS T aset teet aee ete os I a ee axe eaa haa 43 Beep Message Errors at POST eersenonetniaid tnan ennemi tnn nena 44 General Problems teret ena n thi aea es ve TR RR ERR NR RU ran ne dn 45 Having the PT 8850 Serviced ceca nn erkennen 46 Isjeiziellleulen jtee rm taaeas Ea 47 CHAPTER 1 GETTING STARTED This chapter describes the procedures from unpacking the PT 8850 POS to powering it on The following topics are described Unpacking the machine on page 1 Checking the package contents on page 2 Identifying components on page 3 Removing the rear cover on page 6 Adjusting display angles on page 7 Setup considerations on page 7 Connecting peripheral devices on page 8 Connecting a cash drawer on page 8 Powering the machine on and off on page 9 Unpacking the machine The machine and cable accessories are packed in a cardboard carton with foam padding for protection during shipping Figure 1 1 Unpacking the machine Carefully unpack the machine and keep the packing
74. rd Disk Boot Priority Selecting Hard Disk Boot Priority opens up this screen Phoenix AwardBIOS CMOS Setup Utility Item Help Hard Disk Boot Priority Figure 2 6 Hard Disk Boot Priority submenu ti2 Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Hard Disk Boot Priority This screen allows setting the boot priority Use the PageUp and PageDown to change the order And then his Esc to set 19 Advanced Chipset Features This option displays critical timing parameters of the mainboard Leave the items on this menu at their default settings unless you are very familiar with the technical specifications of the system hardware If you change the values incorrectly you may introduce fatal errors or recurring instability into the system Phoenix AwardBIOS CMOS Setup Utility Advanced Chipset Features System BIOS Cacheable Item Help Memory Hole At 15M 16M gt PCI Express Root Port Func PEG Onchip VGA Control On Chip Frame Buffer Size DVMT Mode DVMT FIXED Memory Size Figure 2 7 Advanced Boot Display Erud NODT Chipset Features menu ti Move Enter Select PU PD Value F10 Save ESC Exit Fl General Help F5 Previous Values F6 Fail Safe Defaults F7 0ptimized Defaults System BIOS Cacheable These items allow the system to be cached in memory for faster execution We recommend that you leave these items at the default value Memory
75. re 1 6 Figure 1 5 Adjusting the display Figure 1 6 Adjusting the customer display Setup considerations When setting up the PT 8800 consider the following e Use a desktop or counter that is stable and even Ensure there is enough room around the sides and rear of the PT 8800 for ventilation Ensure there is room to connect cables and that cables are long enough to reach peripheral devices or a power outlet Adjusting display angles 7 Connecting peripheral devices Peripheral devices such as a printer or scanner can be connected to the PT 8800 Refer to the user manual of the device you are connecting for instructions on installing drivers where needed Remove the rear cover to access the connec tors See Removing the rear cover on page 6 Amplifier or speakers l E COM2 Pa Cashdrawer ND Mouse Printer Powered USB Compliant devices 24V Keyboard Monitor i or router Powered USB Microphone Compliant devices 12V Figure 1 7 Connecting peripheral devices Do not plug a phone line into the RJ 45 ADSL or router connector Doing so can damage the connector CAUTION Connecting a cash drawer Refer to the following to connect a cash drawer The cash drawer RJ 11 connector is DC 24V Ensure the cash drawer to be con nected matches this power specification IMPORTANT 1 Remove the rear cover See Removing the rear cover on page 6
76. sfer protocol for the parallel port There are five options SPP Standard Parallel Port EPP Enhanced Parallel Port ECP Extended Capabilities Port ECP EPP and PntMode The default setting is SPP SPP allows data output only Extended Capabilities Port ECP and Enhanced Parallel Port EPP are bi directional modes allowing both data input and output ECP and EPP modes are only supported with EPP and ECP aware peripherals PntMode allows the parallel port to operate in bipoloar mode Integrated Peripherals 31 ECP Mode Select Sets the ECP mode version The default setting is EPP1 7 ECP Mode Use DMA When the onboard parallel port is set to ECP mode the parallel port can use DMA 3 or DMA 1 The default setting is 3 Onboard COM3 This option is used to assign the I O address and IRQ for the onboard COM port 3 The default setting is 3ES IRQS Onboard COM4 This option is used to assign the I O address and IRQ for the onboard COM port 4 The default setting is 2ES IRQS Onboard COM5 This option is used to assign the I O address and IRQ for the onboard COM port 5 The default setting is 4F8 IRQS5 Onboard COM6 This option is used to assign the I O address and IRQ for the onboard COM port 6 The default setting is 4ES IRQS lp To supply power to the customer display the COMG voltage is factory set to DC 12V Power Management Setup Option Use this to control system power management Modern operating systems take care of much of the
77. ssseeee en 9 CHAPTER 2 BIOS SETUP 255 pH bEnoSo cou a duGa dass 11 About the Setup Utility rrt e eor err e terree p eaa ts 11 Entering the Setup Utility caen 12 BIOS navigatlom Keys ean ett ed ettari tid D ed tad 12 Using BIOS iicet pedi acces EM Pe eR pe a EIUS 13 standard CMOS features de dd cda a d ue a c 14 Advanced BIOS Features ertet eth kein innare nena npe 16 WF CPU Feature is nti erede erg ba ge e ett d gv bu etg e td oes 18 gt Hard Disk Boot Priotity rrr rer ee rite e ER RR ERR 19 Advanced Chipset Features risona aa e a E aR 20 gt PCI Express Boot Port FUNC ssssssseseeee 21 Integrated Peripherals itti e ete eg eed e e tede 22 BP OnChip IDE Device ssseeememmenenmnmen 23 P SuperlO DEVICE tee er et tete arbe ede b aas Ree Maen 25 P USB Device Setllng ct rete ee gun Ee ret ke redeas aer beet ede ge 26 Power Management Setup itat eate te i Ebert d n d d ba 27 PnP PCI Configurations cr rr Era REPETI X EX EE bax EE ED X Rx E ERR ERE EEPS 29 P IRQ ROSOUECOS non ertet este deer er eer na ard abad de dan cui 30 PG Health Status im re rx rete Re RARE eR OPE d ages 31 Other BIOS OPTIONS c seiten ent t net dear e ei ete e hi dte eee Tuus 32 CHAPTER 3 UPGRADING COMPONENTS sesss 35 Salet and precautlolis aee tere ae ex a be c 35 Before YOU BEGIN Rr a x ERREUR REM XXX UR Ra Lax uut tux RA MEA eeu RUE 36 Upg
78. st stable condition The default setting is SPD CAS Latency Time This item enables you to specify the time delay in clock cycles or CLKs that elapses before the SDRAM carries out a read command after receiving it The value specified here also sets the number of CLKs that will elapse for the com pletion of the first part of a burst transfer Low values indicate a faster data transaction When synchronous DRAM is installed the number of clock cycles of CAS latency depends on the DRAM timing The default is 2 5 Active to Precharge Delay To change the active to precharge delay the DRAM Timing Selectable setting must be set to User The default set ting is 7 DRAM RAS to CAS Delay This item enables you to set the time it takes data to move between the Row Address Strobe RAS and Column Address Strobe CAS You can also insert a timing delay between RAS and CAS When set to higher values reads writes and refreshes take longer but data is transferred with better reliability The default setting is Auto 26 Chapter 3 BIOS Setup Utility DRAM RAS Precharge Time DRAM must continually be refreshed or it will lose its data Normally DRAM is refreshed entirely as the result of a single request This option allows you to determine the number of CPU clocks allocated for the Row Address Strobe RAS to accumulate its charge before the DRAM is refreshed If insufficient time is allowed refresh may be incom plete and data lost The def
79. te nien dte onte iE etidm e e e etam 43 Having the PTS 800 Serviced iren eee dA ru edet atu toe cis 44 NOUS CIS ERR EE MN 44 Figure 1 1 Figure 1 2 Figure 1 3 Figure 1 4 Figure 1 5 Figure 1 6 Figure 1 7 Figure 3 1 Figure 3 2 Figure 3 3 Figure 3 4 Figure 3 5 Figure 3 6 Figure 3 7 Figure 3 8 Figure 3 9 Figure 3 10 Figure 3 11 Figure 3 12 Figure 3 13 TABLE OF FIGURES Unpacking the P T5590 coche see oue ede uei ee oet ee aet fetum edd 1 Front right view of PT 8800 sf es ct ecce decree eate te uo cs deat Pa re cn teed 3 Rear right view of PT 8800 iicet ide etes elec dei debe tei eie ep eu 4 Rear connectors labeled odas od ree ttbi etae it epa uude qup eas dia deu 5 Adjusting tlie display csi o mt tiet els ax ER RERO insets A LI MER UA A 7 Adjusting the customer display cese re Scito opo ten eta HO Cen e bes eve E bdu ds 7 Connecting peripheral devices sse et ep arse eene eese aeter eto uae oed Needs genus 8 Mati BIOS ment s oo cete the an a aso flrs Oe ans ea eae acy 20 Standard C MOS Features nerui ideo aset i avis ted esi at dus tia quo eoa bee PA ed Ia dua ids 21 IDE Primary Master Submenu sait tecta eta pr o cre iba cos eae ti e P a a 22 Advanced BIOS Features DIO cos cien ppt eee ooa dE o eie peut tb vetet dau RN 24 Advanced Chipset Features menu aos ocsc e e ee or ette ORE ee e senses AN ciase oes 26 Integrated Peripherals fent ose v o eae ud nu I EU Ut NI Utt 28 Ont Ip IDE Device CTU oce Re des lbreore ases utes ete deb a
80. the amount of extended memory detected by the system during boot Total Memory This field displays the total amount of memory Base and Extended detected by the system during boot Press lt Esc gt to return to the main menu Standard CMOS Features 23 Advanced BIOS Features Selecting Advanced BIOS Features on the menu displays this menu Phoenix AwardBIOS CMOS Setup Utility Advanced BIOS Features Virus Warning Disabled CPU L1 amp L2 Cache Enabled Quick Power On Self Test Enabled Menu Level M First Boot Device CDROM Second Boot Device HDD 0 Allows you to choose Third Boot Device Disabled the VIRUS warning Boot Other Device Enabled feature for IDE Hard Boot Up NumLock Status On Disk boot sector Gate A20 Option Fast protection If this Item Help Typematic Rate Setting Disabled function is enabled Typematic Rate Chars Sec 6 and someone attempts Typematic Delay Msec 250 to write data into this Security Option Setup area BIOS will show a OS Select For DRAM 64MB Non 0S2 warning message on Report No FDD For WIN 95 No screen and alarm beep Small Logo EPA Show Disabled Tl Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 3 4 Advanced BIOS Features menu Virus Warning When enabled this item provides protection against viruses that try to write to the boot sector and partition table of
81. tility on page 11 Standard CMOS features on page 14 Advanced BIOS Features on page 16 CPU Feature on page 18 Hard Disk Boot Priority on page 19 Advanced Chipset Features on page 20 Integrated Peripherals on page 22 Power Management Setup on page 27 PnP PCI Configurations on page 29 PC Health Status on page 31 Other BIOS Options on page 32 About the Setup Utility The BIOS Setup Utility enables you to configure the following items Hard drives diskette drives and peripherals Video display type and display options Password protection from unauthorized use Power management features This Setup Utility should be used for the following When changing the system configuration When a configuration error is detected and you are prompted to make changes to the Setup Utility When trying to resolve IRQ conflicts When making changes to the Power Management configuration When changing the User or Supervisor password 11 Entering the Setup Utility When you power on the system BIOS enters the Power On Self Test POST routines POST is a series of built in diagnostics performed by the BIOS After the POST routines are completed the following message appears Press DEL to enter SETUP Press the delete key Delete to access the Award BIOS Setup Utility Phoenix AwardBIOS CMOS Setup Utility Select Item Save amp Exit Setup Time Date Hard Disk Type Figure 2 1 Main BIOS menu BIOS naviga
82. ting a password that is already installed Write the passwords down and keep them in a safe place If you do not save changes when you exit BIOS changes to the passwords will be saved anyway IMPORTANT Save amp Exit Setup Option Highlight this item and press Enter to save the changes that you have made in the Setup Utility and exit the Setup Utility When the Save and Exit dialog box appears press lt Y gt to save and exit or press lt N gt to return to the main menu Frequency Voltage Control Option 39 Exit Without Saving Highlight this item and press Enter to discard any changes that you have made in the Setup Utility and exit the Setup Utility When the Exit Without Saving dialog box appears press Y to discard changes and exit or press lt N gt to return to the main menu ll If you have made settings that you do not want to save use the Exit Without Saving item and press Y to discard any changes you have made 40 Chapter 3 BIOS Setup Utility APPENDIX This appendix describes locating and solving problems that you may encounter while using the PT 8800 Troubleshooting Often after time spent troubleshooting the problem is traced to something as simple as a loose connection Check the following before proceeding to the problem specific solutions Tips for Troubleshooting In each problem specific section try the steps in the order suggested This may help you to solve the problem more qu
83. tion keys The BIOS navigation keys are listed below Scrolls through the items on a menu PU PD Modifies the selected field s values Exits the current menu Bl Displays a screen that describes all key functions Loads previously saved values to CMOS Loads a minimum configuration for troubleshooting F7 Loads an optimum set of values for peak performance F10 Saves the current configuration and exits Setup Shift F2 Changes the color of the BIOS menu 12 CHAPTER 2 BIOS SETUP Using BIOS When you start the Setup Utility the main menu appears The main menu of the Setup Utility displays a list of the options that are available A highlight indicates which option is currently selected Use the cursor arrow keys to move the highlight to other options When an option is highlighted execute the option by pressing lt Enter gt Some options lead to pop up dialog boxes that prompt you to verify that you wish to execute that option Other options lead to dialog boxes that prompt you for information Some options marked with a triangle lead to submenus that enable you to change the values for the option Use the cursor arrow keys to scroll through the items in the submenu 13 Standard CMOS features Selecting Standard CMOS Features on the main menu displays the following menu Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Time hh mm gt
84. tor the parameters for critical voltages and critical temperatures Several fields are for information only and are not configurable Phoenix AwardBIOS CMOS Setup Utility Item Help PC Health Status CPU Warning Temperature Figure 2 16 PC Health Status menu Smart Fanl Temperature Fanl Tolerance Value Smart Fan2 Temperature Fan2 Tolerance Value t Move Enter Select PU PD Value F10 Save ESC Exit F1l General Help F5 Previous Values F6 Fail Safe Defaults F7 0ptimized Defaults These items display the current status of system temperatures and power status Shutdown Temperature This item allows setting the shutdown temperature Once enabled the machine will automatically shutdown when the temperature reaches the limit specified CPU Warning Temperature This item when enabled will sound an alarm when the temperature exceeds a particular setting Smart Fan1 Temperature This item is used to set Smart Fanl target temperature value Fan1 Tolerance Value This item used to set tolerance of Fanl target temperature value Smart Fan2 Temperature This item is used to set Smart Fan2 target temperature value Fan2 Tolerance Value This item used to set tolerance of Fan2 target temperature value 31 Other BIOS Options This section covers the other options that are available from the main menu Phoenix AwardBIOS CMOS Setup Utility So fesse t Select Item Save amp Exit Setup Time Date Hard Disk Type
85. ttached The Power On Self Test The Power On Self Test POST runs every time you turn on or reset the computer The POST checks memory the mainboard the display the keyboard the disk drives and other installed options If failure is detected in an area other than the mainboard such as the keyboard or an adapter card an error message is displayed on the screen and testing is stopped If your system does not successfully complete the POST but displays a blank screen have the PT 8850 serviced Beep Errors at POST There are two kinds of beep codes in the BIOS Video error a single long beep followed by three short beeps indicates a video error the screen can not be initialized and no information can be displayed DRAM error a single long beep indicates that a DRAM error has occurred 43 Beep Message Errors at POST If the BIOS detects an error during the POST a message is displayed Refer to the following table for a list of the errors that display mainboard to keep time There is a risk of explosion if the wrong battery type is used when replacing Dispose of used batteries according to lo WARNING c3 ordinance regulations The system uses a 3V CR2032 battery CMOS battery mounted on the ERROR MESSAGE SOLUTION CMOS BATTERY HAS FAILED The CMOS battery is depleted Replace the battery The battery may be weak Replace the battery CMOS CHECKSUM ERROR The CMOS may be corrupt H
86. ues F6 Fail Safe Defaults F7 Optimized Defaults Figure 3 7 OnChip IDE Device menu On Chip Primary Secondary PCI IDE Use this item to enable or disable the PCI IDE channels that are integrated on the mainboard The default setting is Enabled IDE Primary Secondary Master Slave PIO Each IDE channel supports a master device and a slave device These four items let you assign which kind of PIO Programmed Input Output is used by IDE devices Choose Auto to let the system auto detect which PIO mode is best or select a PIO mode from 0 4 The default setting is Auto Primary Secondary Master Slave UltraDMA Each IDE channel supports a master device and a slave device This mainboard supports UltraDMA technology which provides faster access to IDE devices If you install a device that supports UltraDMA change the appropriate item on this list to Auto You may have to install the UItraDMA driver supplied with this mainboard in order to use an UltraDMA device The default setting is Auto IDE HDD Block Mode Enable this field if your IDE hard drive supports block mode Block mode enables BIOS to automatically detect the optimal number of block read and writes per sector that the drive can support and improves the speed of access to IDE devices The default setting is Enabled Integrated Peripherals 29 Onboard Device Use this item to enable or disable the USB and devices that are integrated on the mainboard Select the item and press lt Ent
87. vstem The system will not boot and access to Setup will be denied if the correct password is not y entered at the prompt The system will boot but access to Setup will be denied if the correct password is not PROUD entered at the prompt APIC Mode This item is used to activate the ACPI Advanced Configuration and Power Management Interface Mode ACPI is a power management specification that makes hardware sta tus information available to the operating system ACPI enables a PC to turn its peripherals on and off for improved power management It also allows the PC to be turned on and off by external devices so that IMPORTANT mouse or keyboard activity wakes up the machine Small Logo EPA Show This item enables you to show the company logo on the bootup screen 17 gt CPU Feature Selecting CPU Feature opens up this screen Phoenix AwardBIOS CMOS Setup Utility CPU Feature Limit CPUID MaxVal Item Help Execute Disable Bit Figure 2 5 CPU Feature submenu t Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 0ptimized Defaults Limit CPUID MaxVal When enabled this feature will make the BIOS respond suitable virtual CPUID to OS kernel So WinNT or the legacy OS can use the masked CPUID to work well with the new CPU design Execute Disable Bit When disabled forces the XD feature flag to always return 0 18 CHAPTER 2 BIOS SETUP gt Ha
88. warnings and cautions in this manual and on the unit case When replacing parts ensure that your service technician uses parts specified by the manufacturer Avoid using the system near water in direct sunlight or near a heating device keep time There is a risk of explosion if the wrong battery type is used when replacing Dispose of used batteries according to local ordinance WARNING regulations 5 The system uses a 3V CR2032 battery mounted on the mainboard to The USB ports can be damaged if care is not taken when connecting AN devices Ensure USB devices are correctly inserted Plugging a phone line into the LAN port RJ 45 connector can damage CAUTION the connector Take care only plug an RJ 45 connector into the LAN port Revision history Version 1 0 July 2009 TABLE OF CONTENTS CHAPTER 1 GETTING STARTED iria dona dari tob chu duae duae 1 Unpacking the machine sssssssseenne eene nnns 1 Checking the package contents ssssssssseee eee 2 Identifying components sss mmm eene nnns 3 Removing the rear COVE ncscias cd aa ecce oo e eh ecu cesa ces 6 Adjusting display angles sem emen 7 Set p considerations 6 orci Repo ro a aa eH TE UAE aa FAQ Y ROVER Y PER Rud s 7 Connecting peripheral devices ssssssssssssmenne 8 Connecting a cash drawer ecce nesee creo deae eee eae 8 Powering the machine on and off sssssssss
89. xit the Setup Utility When the Save and Exit dialog box appears press lt Y gt to save and exit or press lt N gt to return to the main menu Exit Without Saving Highlight this item and press Enter to discard any changes that you have made in the Setup Utility and exit the Setup Utility When the Exit Without Saving dialog box appears press Y to discard changes and exit or press XN to return to the main menu fr If you have made settings that you do not want to save use the Exit j Without Saving item and press Y to discard any changes you have e f made NOTE 33 34 CHAPTER 2 BIOS SETUP CHAPTER 3 UPGRADING COMPONENTS This chapter describes how to upgrade components for the PT 8850 The following topics are described Safety and precautions on page 35 Before you begin on page 36 Upgrading the hard drive on page 37 Installing optional displays on page 38 Attaching the second display on page 40 Installing a CompactFlash card on page 42 Installing a PCI E x1 card on page 43 Safety and precautions Computer components and electronic circuit boards can be damaged by discharges of static electricity Working on computers that are still connected to a power supply can be extremely dangerous Follow these guidelines to avoid damage to the computer or injury to yourself Always disconnect th
90. y Do not place the unit on an unstable surface cart or stand Do not block the slots and opening on the unit which are provided for ventilation Do not push objects in the ventilation slots as they may touch high voltage components and result in shock and damage to the components Only use the power source indicated on the marking label If you are not sure contact your dealer or the Power Company The unit uses a three wire ground cable which is equipped with a third pin to ground the unit and prevent elec tric shock Do not defeat the purpose of this pin If your outlet does not support this kind of plug contact your electrician to replace your obsolete outlet Do not place anything on the power cord Place the power cord where it will not be in the way of foot traffic Follow all warnings and cautions in this manual and on the unit case When replacing parts ensure that your service technician uses parts specified by the manufacturer Avoid using the system near water in direct sunlight or near a heating device The system uses a 3V CR2032 battery mounted on the mainboard to keep time There is a risk of explosion if the wrong battery type is used when replacing WARNING Dispose of used batteries according to local ordinance regulations The USB ports can be damaged if care is not taken when connecting devices Ensure USB devices are correctly inserted Plugging a phone line into the LAN port RJ 45
91. y have to install the UltraDMA driver supplied with this mainboard in order to use an UltraDMA device On Chip Secondary PCI IDE Use this item to enable or disable the PCI IDE channels that are integrated on the mainboard 23 SATA Mode This feature allows users to select SATA mode LEGACY Mode Support This feature allows users to enable dsiable the LEGACY Mode 24 CHAPTER 2 BIOS SETUP gt SuperlO Device Use this item to change settings for I O devices Select the item and press Enter to open the following menu Phoenix AwardBIOS CMOS Setup Utility SuperIO Device POWER ON Function Item Help Onboard Serial Port 1 Onboard Serial Port 2 UART Mode Select Onboard Parallel Port Parallel Port Mode PWRON After PWR Fail Figure 2 11 SuperlO Device submenu t12 Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 0ptimized Defaults POWER ON Function This feature allows you to select the method to turn on your computer Hot Key Power ON Older keyboards that do not conform to the Keyboard 98 standard and therefore do not have the special wake up button can use the Hot Key option instead There are twelve hot keys available Ctrl F1 to Ctrl F12 Select the hot key you want and you will be able to start up the computer using that hot key Onboard Serial Port 1 2 These items are used to assign the I O address and IRQ for the onboard serial port 1 2 UAR
92. your hard disk drive You need to disable this item when installing an operating system We recommend that you enable anti virus protection as soon as you have installed an operating system The default setting is Disabled CPU L1 amp L2 Cache Most processors that can be installed in this mainboard use internal level 1 L1 and level 2 L2 cache memory to improve performance Leave this item at the default setting for better performance The default setting is Enabled Quick Power On Self Test Enable this item to shorten the power on testing POST and have your system start up faster You can enable this item after you are confident that your system hardware is operating smoothly The default setting is Fast First Second Third Boot Device The BIOS loads the operating system from the disk drives in the sequence selected in these three fields The default setting is Floppy CD ROM HDDO Boot Other Device When enabled the system searches all other possible locations for an operating system if it fails to find one in the devices specified under the First Second and Third boot devices The default setting is Enabled Boot Up NumLock Status This item defines if the keyboard Num Lock key is active when your system is started The default setting is On 24 Chapter 3 BIOS Setup Utility Gate A20 Option This item defines how the system handles legacy software that was written for an earlier generation of processors Leave this item at th

User manual

Contents

Download Pdf Manuals

Related Search

Related Contents