2-3 SAS/SATA II HDD Canister USER'S MANUAL
Contents
1. or mechanical including photocopying recording storing in an information retrieval system or translating in whole or in part without the prior written consent of manufacturer Trademarks Product and company names mentioned herein are trademarks or trade names of their respective companies Changes The Manufacturer reserves the right to revise this publication and to make changes in the content hereof without the obligation of The Manufacturer to notify any person of such revision or changes 1v Safety Precautions v The equipment has been dropped and or damaged Before getting started please read the following important cautions Y The equipment has obvious signs of breakage m All cautions and warnings on the equipment or in the manuals should be noted v Please disconnect this equipment from the AC outlet before cleaning Do not m Most electronic components are sensitive to electrical static discharge therefore be use liquid or detergent for cleaning The use of a moisture sheet or cloth is sure to ground yourself at all times when installing the internal components Use a recommended for cleaning grounding wrist strap and place all electronic components in static shielded devices Grounding wrist straps can be purchased in any electronic supply store m Do not open the system s top cover If opening the cover for maintenance is a must only a trained technician should do so Integrated circuits on computer boards are se2. 2 3 SAS SATA II HDD Canister XC 23D1 SA10 0 R USER S MANUAL Document number MAN 00076 A Preface Important Information Warranty Our product is warranted against defects in materials and workmanship for a period of one year from the date of shipment as evidenced by receipts or other documentation Manufacturer at its option repair or replace eguipment that proves to be defective during the warranty period This warranty includes parts and labor The media on which you receive software are warranted not to fail to execute programming instructions due to defects in materials and workmanship for a period of 90 days from date of shipment as evidenced by receipts or other documentation Manufacturer will at its option repair or replace software media that do not execute programming instructions if manufacturer receives notice of such defects during the warranty period Manufacturer does not warrant that the operation of the software shall be uninterrupted or error free National Instruments believes that the information in this document is accurate The document has been carefully reviewed for technical accuracy In the event that technical or typographical errors exist manufacturer reserves the right to make changes to subseguent editions of this document without prior notice to holders of this edition The reader should consult National Instruments if errors are suspected In no event shall manufacturer be liable for any damages ar
3. ising out of or related to this document or the information contained in it EXCEPT AS SPECIFIED HEREIN MANUFACTURER MAKES NO WARRANTIES EXPRESS OR IMPLIED AND SPECIFICALLY DISCLAIMS ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE CUSTOMER S RIGHT TO RECOVER DAMAGES CAUSED BY FAULT OR NEGLIGENCE ON THE PART OF MANUFACTURER SHALL BE LIMITED TO THE AMOUNT THERETOFORE PAID BY THE CUSTOMER MANUFACTURER WILL NOT BE LIABLE FOR DAMAGES RESULTING FROM LOSS OF DATA PROFITS USE OF PRODUCTS OR INCIDENTAL OR CONSEQUENTIAL DAMAGES EVEN IF ADVISED OF THE POSSIBILITY THEREOF This limitation of the liability of manufacturer will apply regardless of the form of action whether in contract or tort including negligence Any action against manufacturer must be brought within one year after the cause of action accrues Manufacturer shall not be liable for any delay in performance due to causes beyond its reasonable control The warranty provided herein does not cover damages defects malfunctions or service failures caused by owner s failure to follow the manufacturer installation operation or maintenance instructions owner s modification of the product owner s abuse misuse or negligent acts and power failure or surges fire flood accident actions of third parties or other events outside reasonable control 111 Copyright Under the copyright laws this publication may not be reproduced or transmitted in any form electronic
4. n Blue color On when HDD is detected as failure by host HDD Failure Flash RAID rebuilding Red color Off when there is no HDD or normal only supported on HBA 1 4 Rear Panel Features 2 4 1 rear view of 2 to 3 canister O Power input connectors OO Over Temp Threshold amp Buzzer Setting SATA connector O Fan HDD Fail LED Input O Fan connector More details as below Power input connectors Four pin standard power connectors for 12V 5V GND Over Temp Threshold 8 Buzzer Setting Setting for Over Temp alarm threshold Pin Number Description 1 2 50c 3 4 45 C 5 6 Buzzer Disable 3 4 SATA Connectors CHAPTER 2 INSTALLATION OVERVIEW Warning Before you remove or install the unit make sure the unit is not turned on or Standard 7Pin SATA connector to link to MB or HBA card connected to the AC power 2 1 Removing the HDD Tray from the enclosure 1 Press the latch to the right by the thumb 2 Pull the tray door outward by the forefinger at the same time 9 HDD Fail LED Input Pin Number Description HDD2_ERR 1 GND HOD1 ERR HDDO_ERR GND 3 Remove the HDD tray from the enclosure 4 Install the four mounting screws to secure the drive in the disk tray For some HBA supporting HDD Fail LED s If used the jumper is used to connect to cathode of the diode for HDD Fault output from HBA It s left to open a
5. nsitive to static electricity Before handling a board or integrated circuit touch an unpainted portion of the system unit chassis for a few seconds This will help to discharge any static electricity on your body m Place this equipment on a reliable surface when install A drop or fall could cause injury Please keep this equipment from away humidity m Do not leave this equipment in an environment unconditioned out of operation or storage temperature range may damage the equipment m Never pour any liquid into ventilation openings This could cause fire or electrical shock m Make sure the voltage of the power source is within the specification on the label when connecting the equipment to the power outlet The current load and output power of loads shall be within the specification This equipment must be connected to reliable grounding before using Place the power cord out of the way of foot traffic Do not place anything over the power cord The power cord must be rated for the product voltage and current marked on the product s electrical ratings label The voltage and current rating of the cord should be greater than the voltage and current rating marked on the product mw fthe equipment is not used for a long time disconnect the equipment from mains to avoid being damaged by transient over voltage Never open the equipment For safety reasons only qualified service personnel should open the equipment m f one ofthe following
6. s default when HBA doesn t support it HDD Drive Fan Connectors Bottom view of HDD tray Pin Number Description LF mall 1 GND A Screw 2 3 5 Slide the tray into a slot Press the tray handle until the latch is closed and locks into place A 3 pin fan connector with failure detection
7. situations arise the equipment should be checked by service personnel v The power cord or plug is damaged v Liquid has penetrated the equipment Y The equipment has been exposed to moisture v The equipment does not work well or will not work according to its user s manual Table of Contents CHAPTER 1 INTRODUCTION 1 1 Key features gt Supports three 3 5 SAS and or SATA II drives on 2 ODD Bays space PAG CAS AE O a ee wanton anne weceesneesent iii gt Support direct HDD Fault LEDs input from HBA Card IMportantintormalON registra iii gt Support HDD Activity LEDs directly from SAS SATA II HDD Salely PRECAUTIONS aanraai aTa V gt Enclosure Over Temperature Alarm Buzzer and LED CHAPTER 1 INTRODUCTION ssssssssssssssssesssesssesssessseesseessnessnesssessseesseessess 1 F ANISS PEAME Mono R Sating gt Fan Speed Control Ttt K y feature ta 1 t2 Unpacking ISten E A 1 1 3 Front Panel Features oooccccccccccoonncccnnccconononanennnnnnnnonnnnnnnnnnnnnononanrennnnos 2 1 2 Unpacking list 1 4 Rear Panel Falun iii 3 Before removing the subsystem from the shipping carton visually inspect the physical CHAPTER 2 INSTALLATION OVERVIEW s ssssssssssssssssssssssstsessssssseesseessssess 5 Se OU a Sen ary MICELI CHINE SUMO May MCC ean contents of the carton are damaged If any damage is found do not remove the components 2 1 Removing the HDD Tray from the enclosure ccccceeeeesseeeeeeeees 5 contact the dealer
8. where the subsystem was purchased for further instructions Before continuing first unpack the subsystem and verify that the contents of the shipping carton are all there and in good condition The package contains the following items MM One set with HDD tray x 3 Shipping without drive devices installed IH Mounting screws x 1 sets M Jumper x 2 Note Inspect the shipping cartons for evidence of physical damage If a shipping carton appears damaged request that the carrier s agent be present when the carton is opened Keep all contents and packing material for the agent s inspection Vil 1 1 3 Front Panel Features O Power LED LED indicators E 9 9 8 x OI OO se Pari JA E Agr A pl fa F me a a So MO a A POT GO jp y 4 DO O a ot t S Ae a LO 98 3 5 OO 5 Dt ome on CDC Ty 1 3 1 front view of 2 to 3 canister O Over Temperature LED Fan Fail LED O Drive tray LED NAME Color definition Behavior Blue On when system is powered on Power LED Off when system is powered off l Over Temperature LED Fan fail LED On when system temperature is higher than threshold temperature when system temperature is normal On when system detected fan abnormality Off when fan is normal operation On when HDD is inserted and detected HDD Activity Ready Flash when accessing HDD Off when there is no HDD or no detectio
Download Pdf Manuals
Related Search