SPRT SP-POS58Ⅳ Line Thermal Printer User's Manual Beijing
Contents
1. 80mm max Inner Diameter 13mm min Thickness 53 60g m 1 3 Printing Font IBM Character set II ANK 12x24dots 1 25 CW x3 00 CH mm eGB2312 80 Chinese 24x24dots 3 00 CW x3 00 CHO mm 1 4 Interface eSerial interface POS58S DB25 socket orifice supports RTS CTS protocol Baud rate 1200 115200bps Adjustable Data structure one start bit seven or eight data bits one or over one stop bit s no parity s Parallel interface POS58P DB25 sockets needle 80bit parallel interface supports BUSY ACK handshaking protocol TTL signal level eEthernet Interface It is a way to connect to Ethernet for ordinary printer Can work on full duplex or half duplex mode Ethernet 802 3 protocol upper layer protocols have TCP UDP ICMP IP ARP HTTP eCash drawer control DC12V 1A 60pinRJ 11socket 1 5 Printing Control Command eCharacter printing command supports double width and double height print of ANK characters user defined characters and Chinese characters the character line spacing is adjustable eGraphics printing command supports the print of bit map graphics and download bit map graphics with different density eGS barcode printing command supports EAN 13 EAN 8 barcode printing 1 6Power Supply SPRT o DC12V 10 2A A 1009 3P Power socket 1 7 Operation Environment Operation temperature 5 40 C Relative humidity 10 80 Storage temperature 20 602. 2 3 5 Power Connection POS58IV uses external power supply as12V DC 10 3 5A power socket is A 1009 3P model as Fig 2 8 shows B Fig 2 9 Power Socket 2 4 Buttons and Indicators Power switch Control the status of power EE is power off to push is switch on The feeding button Hold down FEED start paper feeding release the button paper feeding stops If install buzzer it will ring when feeding paper stop ring when feeding stops Opening button Hold down the opening button the upper cover will open Power indicator red show the power switch status SPRT Status indicator green The assignment Indicator status Introduction Scintillation 1 times out Lack paper Scintillation 2 times out Printer head over temperature Figure 2 10 2 5 Self test The self test can check the condition of printer if the printer prints out the self test receipt correctly It means the printer works normally Otherwise it needs to repair The self test will print out the firm ware version interface setting and 128ANK characters Holding down FEED button and turn on the power then release the button self test begins automatically Chapter 3 Printing Control Commands 3 1 Summary POSSSIV offers ESC POS printing command sets Each command is described in following format Printing Command Function Format ASCII the standard ASCII character sequence Decimal the decimal numbers sequence Hex the Hex
3. C Relative humidity 10 90 1 8 Outline Dimension e 138 W X200X L X120 H mm SPRT Chapter 2 Installation and Operation 2 1Printer Appearance Such as figure 2 1 figure 2 2 Paper Roller Upper Cover Printer body Power Indicator Status Indicator Paper Case Feed Button Printer Head Upper Cover Opening Button Lack Paper Figure 2 1 Printer appearance Planform SPRT Print Interface Figure 2 2 Printer appearance back view 2 2Paper Installation POS58IV adopts57 5 0 5mm width thermal paper The steps of thermal paper installation are as the following 1 When there is no paper in the print head please don t press FEED button avoiding to influence the printing head life as figure2 3 hold down PUSH so open the paper case and change paper SPRT Push Button Figure 2 3 Paper Installation 2 Please don t draw the paper forwards or backwards with hands 2 3 Interface Connection 2 3 1 Serial Interface Connection The serial interface of SP POSSSIV printer is compatible with RS232C standard supports RTS CTS handshaking protocol it uses DB25 socket orifice the pin order of the serial port is as Fig 2 4 shows SPRT Fig 2 4Pin Order of the Serial Port The pin assignment of serial interface is shown in Fig 2 1 Pin No Signal j Hos Printer receives data from host 3 TXD Printer Printer transmits control code X ON X OFF and
4. data to host Printer Signal MARK indicates that the printer is BUSY and unable to receive data SPACE 2 Sm indicates that the printer is READY for receiving data e DSR Printer ha space indicates that the printer is online Fig 2 1Pin Assignment of Serial Interface Note D Source denotes the source that signal comes from 2 Logical signal level is EIA The baud rate and data structure in serial interface mode are set to 9600bps 8 data bits no parity bit andlor overlstopbit s The serial interface of POSS8IV can be connected to standard RS 232C interface When connected to IBM PC or compatible machine connection can according to Fig2 5 SPRT Printer 25 pin IBM PC S Printer2 Spin M PC Serial Socket Interface DB09 Socket InterfaceDB025 Fig 2 5Connection between POS58S and IBM PC Serial Interface Sketch Map 2 3 2 Parallel Interface Connection The parallel interface of SP POSS58P printer is compatible with CENTRONICS supports BUSY and ACK handshaking protocol it uses DB25socket needle the pin order of parallel port is as Fig 2 6 shows 6666666666666 8666666666666 14 25 Fig 2 6Pin Order of the Parallel Port The pin assignment of parallel interface is shown in Fig 2 2show Note C n denotes inputting to the printer Out denotes outputting from the printer Signal level is TTL standard 2 3 4 Cash Drawer Interface SPRT The cash drawer interfac
5. number sequence Explanation what the command does and how to use it Example some examples are listed to illustrate the command for better understanding SPRT 3 2 Command Specifications 3 2 1 Printing Command LF Print and Feed Line Format ASCII LF Decimal 10 Hex UA Explanation Print the content in the buffer and feed paper one line Only feed paper Forwards one line if the buffer is empty ESC J Print and Feed n Line Format ASCII ESC J n Decimal 27 74 n Hex 1B 4A n Explanation Print the content in the buffer and feed paper n dot lines n 203 inch n 0 255 This command is only valid for current line and will not change the space Example AAA ee BBB n 203inch ndotlines 3 2 2Line Space Setting Commands ESC 2 Set Line Spacing to 1 6 Inch Format ASCII ESC 2 Decimal 27 50 Hez 1B 32 Explanation Set line spacing to1 6 inch SPRT ESC 3 Set Line Spacing to n Dot Lines n 203inch Format ASCII ESC B n Decimal 27 51 n Hex 1B 33 n Explanation n 0 255 Set line spacing to n dot lines n 0 255 One dot line is 1 203 inch for POSSSIV this command sets the dot line spacing to n 203inch Default n 10 Example AAA BBB 3 2 3Character Printing Commands 2230 30 dot spacing 30 203inch gt Mo ESC Set Character Print Mode Format ASCII ESC n Decimal 27 33 n Hex 1B 21 n Explanation ESC nisa comprehensive command to set character print mode is used
6. redde 20 32 D cOtber C Omrnatidsossusen e eeepc Ge Rene ri bles n Geb itera utr iba 22 Appendix 1 Performance Index sese see 28 Appendix 2 Index of Printing Commands sss sees 30 Appendix 3 Index of Printing Characters 12 ere o da qo ex Prise ire aet rete Ro Uu reus 33 SPRT Introduction POS58IVprinter is a new type line thermal printer it features in fast speed printing low printing noise high reliability perfect printing quality and ribbon needless avoiding the vexation of regular maintenance POSSSIV printer small in outline dimension simple operation and extensive application especially suitable for commercial cash register PC POS bank POS and all kinds of receipts printing Chapter 1 Characteristic Specification 1 1Printing Specification ePrinting method direct thermal ePrinting paper width 57 5 0 5mm ePrinting density 8dots mm 384dots line ePrinting speed approx 60mm sec eReliability Printing head life 100km Using condition Print 12 x 24 ASCII characters print 50 lines each time intermittent print repeatedly Each dot line printing at the same time should not exceed 25 each character line and one dot vertically printing repeatedly should not exceed11 times Use specified thermal paper e Valid printing width 48mm 1 2 Printing Paper eThermal paper model TF50KS E Japan paper co ltd AFSOKS E JUJO THERMAL SPRT e Thermal paper Width 57 5x0 5mm Outer Diameter
7. 4 dots single 24 al density 203DPI 101DPI 33 24 dots double nis used to select bit map graphics mode 8 dots 24 dots dots map data bitmap dots map data bitmap GS print download bit map graphics Format ASCH GS n Decimal 29 47 n Hex ID 2F n Explanation This command is used to print download bit map graphics n 0 3 SPRT To define downloading bit map graphics using GS command Bit map mode Vertical densit 203DPI 203DPI Double height I01DPI Double width 203DP1 101DPI MICI SPRT GS a Define download bit map graphics Format ASCII GS N nl n2 d k Decimal 29 42 nl n2 d k Hex 1D 2A nl n2 d k Explanation This command is used to define download bit map graphics nl 1 48 n2 1 255 nlxn2 1200 k 7n1xn2x8 ed is the bit map data The horizontal size of this graphics is n1x8 dots and vertical size is n2x8dots The definition is valid until re define power off or system reset Format of the download bit map data is shown as follows ni x MSB nd x LSE dnx e 3 2 6Barcode Print GS W Set barcode width Format ASCII GS W nl n2 Decimal 29 87 nl m Hex ID 57 nl n2 Explanation nl barcode narrow bar width unit dot Each dot for POS58IV printer is 1 203 inch or 0 125mm Default n1 3 n2 barcode broad bar width 20 SPRT GS k Printing barcode Format ASCII GS k n d NUL Decimal 29 107 n d 0 Hex 1D 6B n d 00 n Select the printing barco
8. L ERC p m nl m Decimal 27 112 m nl n2 Hex 1B 70 m nl n2 Explanation This command is to generate a pulse to trigger the opening and closing of the cash drawer n1 n2 define the duration of the trigger pulse 22 SPRT m 0 or 30H 0 nlxn2x255 Opening time is nlx2ms closing time is n2x2ms ESC V Transmit Status of Printer Format Asci ESC V Decimal 27 118 Hex 1B 76 Explanation Send printer status to the host When printer received the command it transfers one byte through TXD serial interface Definition of said byte is shown as below Printer head R Printer head temperature Normal over temperature o HER PUN Without paper Not in use ESC u Transmit Status of Equipment Format ASCII ESC U n Decimal 27 117 n Hex 1B 75 n Explanation Send the peripheral equipment status to the host Default n 0 When printer received this command it transmits one byte through TXD Line of the serial interface to the host The definition of any bit in this byte is as follows 23 SPRT ue p T Cash drawer on High off signal level LOW Jo ESC n Setting serial command Format ASCII ESC n Decimal 27 35 n Hez 1B 23 n Description The command set serial n show serial baud and data format as follows Ed re ues oo 000 111 respectively are gt 1200 2400 4800 9600 19200 38400 57600 115200 Have Checking Even parity chec Without Neglect 7 Checking ways select handle 24 SP
9. MAL Thermal paper roll Width 57 5 0 5mm Outer Diameter 50mm max Inner Diameter 13mm min Thickness 53 60g m Printing Font 12x24dots 1 25 CW x3 00 H mm GB2312 80 Chinese 24x24dots 3 00 CW x3 00 H mm Serial interface DB25 socket orifice supports RTS CTS protocol Baud rate 1200 115200bps Datastructure start bit 8data bits 1stop bit No parity Parallel interface DB25 or 36 socket needle 8bit parallel interface BUSY ACK handshaking protocol TTL signal level Cash drawer control DC12V 1A 6 pin RJ 11 socket Power Supply DC12V 10 2A A 1009 3P socket Operation Environment 28 SPRT Operation temperature 5 50 C Relative humidity 10 80 Storage temperature 20 60 C Relative humidity 10 90 C 29 SPRT Appendix 2 Index of Printing Commands o ESC J Print and feed n dot lines Line spacing setting commands Set character line spacing ESC 3 Bet line spacing to n dot lines n 203inch Character printing Commands ESC Set character print mode 15 C ls SO Set double width character print i Cancel double width character E print O ESC Select Cancel User defined Base i 4 ESC amp Define user defined characters Special control ESC c 5 On Off switch Button function commands Graphics print ESC Print bit map graphics commands Print download bit map graphics Define download b
10. RT The default is 9600 without check 8 bit data RTS CTS SSL The method of this command setup leads for passing printer connecting orifice sending into the command to setup baud rate Note when the set is over if have not power the baud still be the baud before setting the set baud will be effective until renew give power The printer will be always use this baud till renew setting need not repeat set when give power each time DLE EOTn Real time status transmission Format ASCII DLE EOT Decimal 10 04 Hex 16 4 n Description Sending the printer state that designated by parameter n just in time n 1 Sending state of the printer n 2 Sending off line state n 3 Sending error state n 4 Sending state of paper sensor When printer receives the command returns to the interrelated status immediately Avoiding to put this command in the command sequence of more than2 characters This command will be also valid even though the printer is set to forbid by the command of ESC selecting peripheral When sending printer current state each state is indicated by l1 byte Transmission state value of the printer can not confirm whether the master computer received Printer will carry out the command immediately once received This command is just available to the serial printer The printer will carry out the command immediately under any state 25 SPRT n 1 Printer state Fix as 0 Fix as 1 One or two cash boxe
11. SPRT SPRT SP POSS8 IV Line Thermal Printer User s Manual Beijing Spirit Technology Development Co Ltd SPRT Content eo UT 3 IO AA NA UA E 3 Chapterl Characteristic Specification eee ee eee 3 Ll Printing Special siesena eare e kii awa 3 A A A aa aa a 3 1 3 Prato ont ta As 4 14 Printing T er T bn R 4 1 5 Printing Control Command sees sese eee eee 4 130 AAA A CIA 4 1 5 Operation Enyitol e Hos ia SS AS 5 1 8 Outline Dimension a ii DE RA EIA AI SAA 5 Chapter 2 System Installation and Operation esee 6 24 Printet APP Caran Ce tido td ari dic 7 22 v A O 8 2 3 Interface COMME 8 2 3 1 Interface CONEA da di ss 10 253 2 Parallel Interface da lo 11 2 3 3 Cash dr wer Inte ERO Gee oreet bm bee i edebat vae si ble drd slan avn 12 DiS FRO WCE CONDECION ESAS 12 24 Buttons and Indicators fa eroi Dr tlt nis e rcd pd eot eed ade wet ea ep dud 13 Chapter3 Print Controling Commands essere eene enne enne ennt 13 EE MEC REUS UU T E URN IM 13 3 2 Command DescripliOll s deed itasse roni bdo 14 3 27 PINE Commands iesean aa 14 3 2 2 Line Spacing Setting Comrmatids cuu o ob leased eee eee e 14 3 2 3 Character Printing COMMAND ls 15 3 24 Special Control Commands vidas vests nt akaka maki as 17 3 2 9 Graphics Printing Commands oe seas Do Seer Renard eie ta baa tse tees Bates 17 3 2 6 Barcode Printing Commands aei eot sees sese eee eee ntu need vue Deu od odor kei
12. de system Barcode 3 EAN 8 2 EAN 13 Pay attention to the specified character number of each barcode EAN 13 and EAN 8 can generate parity characters automatically d 1s the printing barcode data NUL N UL denotes GS K command is over and carry out barcode print GS H Select cancel printing HRI characters Format ASCII GS H n Decimal 29 72 n Hex ID 48 n Explanation n 0 don t print HRI characters Default n 0 n 1 print HRI characters under barcode GS h Set barcode height Format ASCH GS nh n Decimal 29 104 n Hex 1D 68 n Explanation Set the height of printing barcode n 0 255 its unit is dot When n 0 it is 256dots Each dot for POSS8IV printeris1 203inch or 0 125mm Default n 60 GS w Set barcode width Format ASCII GS W n Hex 1D 77 n 21 SPRT Explanation Set the width of printing barcode n 1 4 When n is different the width of bar code will be different as shows in the following tab Narrow size Broad size 1 1 3 aa po Its unit is dot Each dot forPOS58 1v1s1 203 inch or 0 125mm Default n 3 3 2 70ther Commands ESC Initialize printer Format ASCII ESC Decimal 27 64 Hez 1B 40 Explanation ESC command is to initialize the following contents of the printer Clear the data in the printing buffer Restore the default of each printing command Select character printing mode Delete user defined characters ESC p Cash Drawer Control Format ASCI
13. e of POSS8IV adopts RJ 1160 pin socket as Fig2 7 shows Pin No Signal Direction Description Strobe pulse to latch data reading occurs at falling 1 STB In edge 2 DATAI In These signals represent the 1st 3 DATA2 In bit to 8th bit of the parallel 4 DATA3 In interface data each signal is at 9 DATA4 In HIGHT level when data is 6 DATAS In logicl and is LOW when data is 7 DATA6 In logic 0 8 DATA7 In 9 DATAR In Answer pulse LOW level signal indicates that data 10 ACK Out have i already been received and the printer gets ready to receive the next data 11 Busy Out HIGH level signal indicates that the printer is BUSY and cannot receive data 12 PE Out HIGH level signal indicates that paper is end 13 SEL Out Pulling up to HIGH level signal by a resistor Indicates the printer is online 15 ERR Out Pulling up to HIGH level signal by a resistor Indicates there is no error 14 16 17 NC No connection 18 25 GND Grounding logical 0 level Fig 2 2 The pin assignment of parallel interface Figure 2 7 Cash Drawer Interface The pin assignment of the cash drawer interface is as follows SPRT s Signal Direction Cash drawer driver signa 2 Out ash drawer on off status signa 3 In 12VDC 4 Out K HTH ED Cash drawer on off status signal mud 02 Figure 2 8 The pin assignment of the cash drawer interface
14. for selecting print character size Each bit of print parameter n is defined x x D5 D4 x X X X m Double Height Print 1 Double Width Print Default n 0 that means no character enlargement ESC SO Set Double Width Character Printi Format ASCII ESC SO Decimal 27 Hex 1 SPRT Explanation All characters following this command on the same line are printed in double width this command can be canceled by a carriage return or DC4 command ESC DC4 Cancel Double Width Character Print Format ASCII ESC DC4 Decimal 27 20 Hex 1B 14 Explanation After carrying out this command the characters will be printed in normal width ESC Select Cancel User defined Characters ormat 0 n Decimal 27 37 n Hex 1B 25 n Explanation When n 1 select user defined character set When n 0 select internal character set Default n 0 ESC amp Define User defined Characters Format ASCH ESCK s n m a p sxa m n 1 Decimal 27 38 s n m a p sxa m n 1 Hex IB 26 s n m a p sxa m n 1 Explanation ESC amp is used to define user defined characters s 3 32 lt n lt m lt 127 0 lt a lt 12 0 lt p lt 255 es is the number of bytes inverted direction s 3here en is the starting ASCII code of user defined character em is the stopping ASCII code of user defined character When define only one character n m the maximum number of user defined characters is 96 a is the number of dots in horizontal direction p is the data of
15. it map graphics Barcode print Set barcode width commands GS H Select cancel printing HRI character EN D uisus id 30 SPRT C dale Lh E ER a RR Ete Iliad oe ESC v Transmit status of printer esce Transmit status of equipment ES ESC Serial setting commands 31 SPRT Appendix 3 Index of Printing Characters 32
16. s are opening UN Both of cash boxes are closed Lh ANO o MMM ECC MMM 1 Lc 4 1 10 16 al pe 1 5 6 hoa la de E n 2 Off line state Ss 3 a ee e 3 2 o qo fo Close the top cover POS58IV fix as 0 o qo fo Not holding down the feed button Boe js Holding down the feed button 4 1 10 16 i Fix as 1 5 inter 1 20 32 oq mene 00 0 0 00 1 40 64 Error state rop e pP jme 00 0 0 0 0 00 26 P IN Pr NEN PEE o Joo lo ttouncuteremorrossanv sin as 0 v Cutter error n 3 Error state Fix as 1 Noun unrecoverable error fix as 0 Have unrecoverable error k kh Printer head s temperature is normal MO ae E Printer head s temperature is over range 1 40 64 n 4 Feeding paper state bdo lla le aua OO ol lo meepeme iso The paper is going out pl h ls le jmeme o LI Ri e 27 SPRT Appendix 1 Performance Index Printing method Direct thermal Printing width 57 5 0 5mm Valid printing width 48mm Printing density 8dots mm 384dots line Printing speed approx 70mm sec or 20lines s Reliability Printing head life 100 km Using condition Print 12 x 24 ASCII characters print 50 lines each time intermittent print repeatedly Each dot line printing at the same time should not exceed 25 each character line and one dot vertical printing repeatedly should not exceed11 times Use specified thermal paper x Thermal paper roll model TFSOKS E Japan Paper co ltd AFSOKS E JUJO THER
17. self defined characters there are sxa bytes for each character the total number of user defined characters is m n 1 User defined characters are valid until re defined reset or power off format of the user defined characters is shown as follows SPRT we dls m LSB MM m 3 2 4 Special Control Commands Enable Disable Switch Button Function ESC c 5 Format ASCH ESC C 5 n Decimal 27 29 53 Hex 1B 63 35 Explanation When n 1 button LF is enabled When n 0 button FEED is disabled Default n 0 3 2 5Graphics Printing Commands ESC Set Bit map Graphics Format ASCII ESC m nl n2 d k Decimal 27 42 m nl n2 d k Hex 1B 2A m nl n2 d k Explanation Select bit map command m is for setting bit map mode n1 n2 are for setting number of dots d k is for setting contents of bit map m 0 1 32 33 nl 0 255 n2 0 1 d 0 255 k n1 256xn2 m 0 1 k n1 256xn2 x3 m 32 33 The number of horizontal dots of the graphics is nl 256xn2 If the number of dots is more than one line the extra portion will be Ignored referring the following table SPRT 9 d is the bit map data forlof bit means the related dot will be printed And for 0 of bit means the related dot will not be printed k is the total number of dot em is the selected bit map mode S dot demi e DPI CEE 101DPI 80dot double 68DPI mm qe Dm 2
Download Pdf Manuals
Related Search