User's Manual
Contents
1. Technical Support If you run into any problems or have any questions about these products please call our technical support staff at 1 949 588 9997 and ask the operator for technical support Call Monday through Friday from 8 30 AM to 5 00 PM Pacific time Modular Point Source Line Arrays Designed for power portability and versatility CF101LA and CFX101LA modular point source line array systems from Renkus Heinz are the ideal solution for today s small and mid sized ven CF101LA CFX101LA Array Module ues including auditoriums night clubs theaters and houses of worship Individual full range cabinets can be used as a stand alone system either with or without an associated subwoofer They can be flown or pole mounted on a matching subwoofer or standard loudspeaker tripod stand CF15S CFX15S Subwoofer Page 2 MPSA Loudspeaker Systems Modular Point Source Line Arrays continued Suited equally to fixed installation or portable applica tions the full range array cabinets offer consistent 90 horizontal and tight 15 vertical coverage Individual array cabinets can be stacked or arrayed with each cabinet increasing the vertical coverage by 15 degrees Up to four full range modules can be arrayed to provide a 90 by 60 coverage pattern Multi Angle Pole Socket POLE CF101 Pole Floor Mounted Systems Each array cabinet is provided with a multi angle 35 mm pole socket that allows the cabinet s output to be aimed2. C F101LA 52R RHAON Empowered Array Module Connections Power LED Thermal LED Primary Analog Input XLR female Looping Analog Output EN E XLR male Y irm secondary Analog PF2 500R Signal amp Overdrive puta oO uput LED Status Indicators Input Pad amp LED Indicator Serial Digital Audio Input Fault Detect Push Button Volume Controls Fault Relay Mute Buttons Primary amp Secondary AC Power On Off Ethernet CobraNet Inputs RJ 45 female AC Line Voltage AC Line Fuse IEC Power Selector Connector The input panel shown below is for the PF2 500R digital bi amplifier used in the CF101LA 52R The input panel of the PF1 500R amplifier used in the CF101LA 5R is identical except for having only a single Mute button For more detailed information please refer to the Renkus Heinz RHAON User s Manual Page 8 High Frequency Control Settings Not all setups are identical and neither are all rooms The high frequency level controls on the rear of each CF101LA and CFX101LA point source array module allow you to adjust the high frequency output of each module to compensate for the increased loss of high frequency energy from air loss over distance for increased coupling between array modules at low frequencies and for varying room sizes and acoustics They allow you to maintain the proper High Mid Low frequency balance throughout the listening area MPSA Loudspeaker Systems P d RENKUS HEINZ The con
3. CFX101LA 8 96 dB 1W 1m Max SPL 127 dB peak Dispersion 90 Horizontal 15 Vertical Freq Resp 60 Hz to 20 kHz HF Drivers Two 1 SSDCDXI 1730 8 HF Neodymium drivers 75 W RMS 8 Ohms 150 W pgm each LF Driver CF101LA 10 SSL10 10 Neodymium woofer 250 W RMS 4 Ohms 500 W pgm CFX101LA 8 10 SSL10 8 250 W RMS 8 Ohm 500 W pgm Crossover 1700 Hz Enclosure Multi ply hardwood perforated metal grille Power CF101LA 115 V AC or 230 V AC 50 60 Hz CFX101LA 8 500 W pgm at 8 Ohms Finish Black or white custom color optional Hardware Four M10 attachment points Multi angle pole socket Integral flying hardware Dimensions 13 Hx 23 3 4 W x 15 D 33 cm x 60 3 cm x 38 1cm Weight CF101LA 5 amp 5R 56 Lbs 25 4 Kg net CF101LA 52R 58 Lbs 26 3 Kg net CFX101LA 8 54 Lbs 24 5 Kg net CF CFX15S Sensitivit CF15S 5 amp 5R 1 0 V for RPO CFX15S 8 97 dB 1W 1m Max SPL CF15S 5 amp 5R 127 dB peak CFX15S 8 129 dB peak Freq Resp 40 Hz to 120 Hz LF Driver CF15S SSL15 20 15 Neodymium woofer 400 W RMS 4 Ohms 800 W pgm CFX15S 8 SSL15 17 15 Neodymium woofer 400 W RMS 8 Ohms 800 W pgm Enclosure 13 ply hardwood perforated metal grille Finish Black or white custom color optional Power CF15S 5 amp 5R CFX15S 115 V AC or 230V AC CFX15S 8 800 W pgm at 8 Ohms Hardware 8 point univ mtg hdw Metric M10 threads Threaded pole socket Integral flyin
4. ILOIX3O OdI YOd NIV5 dIAV SV Q3UIM 8 SSIX43 JAISSVd SV AJYIM 8 V1101X42 WLI Page 10 MPSA Loudspeaker Systems o c P lt o o c o n o a o LO v gt lt LL O o v c v gt lt LL O pessed q eq 0 speeu I A0SS0 2 AISSEd S UOIYSEJ SIU ui pesn SI SG X49 eui ueuM x SW LZ V1 0LX39 eui Aejep 19joowqns g SG X49 e ui pesn Hula si v1 0LX39 8U ueuM INON 4fofiS008 INON ee S 3NON AON3 Odtd YALNIAD gt o 3NON _ 403 15008 O 3NON OS MUU O 3NON AON3 O3d4td YALNIAD G I IDEEN gp O E 4103 15008 MU O ZH OLS AON3 Odtd YALNIAD SSS SS 1 gp 0 405 008 O S MU O ZH OVC ADNANOAYA YALNAD Page 11 e e gp 6 ZH 9T gp 9 ZH CL dP t Lf en ZHA 8P t 3NON SE ZHA lt 190 8P 8T 120 8P vz 120 8P vz 190 8P vz 120 8P tZ HIYOMYSLLNG HLYOMYALLNG A31IS ZLIADINTI AJTY ZLIMANT HLYOMYSLLNG d1ZH 08 dH ZH OV dH ZH T d1 ZH 9 T dH ZH OS ADNINDIAYS H31N32 d3AOSSOuD VINHON ALIYV10d SWOES O AV140 LNdLNO ap o VITOTXJ9 S dE YO4 NIVS dINV qD cT ap 0 VITOTXAD S2dc YO NIVO dINV qD 8T ap 0 VITOTXJ9 2dY HO4 NIVO dINV dH 11 xx3JALLOV SV Q38IM 8 SSTX3O x diIANV I8 SV Q38IM 8 VITOTX3O VINHON 3NON qD 6 Q31L83ANI 3JNON dP 6 gp 9 dP 0 i Technical Specifications CF CFX101 LA Sensitivity CF101LA 1 0 V for rated power output
5. Modular Point Source Arrays amp Subwoofers User s Manual CFX101LA CFX101LA 8 Externally Powered CF101LA 5 CF101LA 5R CF101LA 52R Self Powered RHAON Empowered CFX15S CFX15S 8 Externally Powered CF15S 5 CF15S 5R Self Powered RHAON Empowered Th RENKUS HEINZ MPSA Loudspeaker Systems Introduction Congratulations on your purchase of a Renkus Heinz CF CFX101LA series point source line array loudspeaker system Your CF CFX series loudspeaker has been designed to provide you years of trouble free high performance listening pleasure We hope you enjoy it Your CF CFX101LA series loudspeaker was carefully tested and fully inspected before leaving our factory and should have arrived in perfect condition Please carefully inspect your loudspeaker and its shipping carton for any noticeable damage and if any damage is found immediately notify the shipping company Only the consignee may institute a claim with the carrier for any damage incurred during shipping Be sure to save the carton and all packing materials for the carrier s inspection Table of Contents Introduction 2 Modular Point Source Line Arrays An Overview 3 Ground Stacked amp Pole Mounted Systems 4 Flying Arrays 5 Subwoofer Assembly 5 EASE Focus 6 CXF101LA Connections 6 CFX101LA 5 Connections 7 CF101LA 5R amp CF101LA 52R Connections 8 High Frequency Control Settings 9 CFX101LA amp CFX15S DSP Settings 1 Technical Specifications 1 N
6. g hardware Optional heavy duty wheels Dimensions 19 H x 23 3 4 W x 22 1 2 D 48 3 cm x 60 3 cm x 56 5 cm Weight CF15S 5 amp 5R 114 Lbs 51 7 Kg net CFX15S 112 Lbs 50 8 Kg net Associated Items RHANG101LA Flybar POLE CF101 Mounting Pole Q RENKUS HEINZ Renkus Heinz Inc 19201 Cook Street Foothill Ranch CA 92610 3501 USA Tel 1 949 588 9997 Fax 1 949 588 9514 Sales renkus heinz com www renkus heinz com RH 723revD November 2011
7. ift etc you will use Rigging Points 3 provided to raise the cabinet into position to the flybar One commonly used arrangement is shackles and a sling S N 3 Raise the cabinet high enough to let you roll or slide the next cabinet into position beneath it 4 Lower the cabinet into position onto the second cabinet and use the quick release pins and joining bars to lock the two cabinets together Move the joining bars from the upper cabinet down into the lower cabinet 5 Repeat the procedure until the array is complete and then lift hoist the array into position and secure it The heavy duty RHANG101LA Flybar supports arrays of up to 6 cabinets 4 array modules and 2 subwoofers Arrays with 3 array modules provide 45 vertical coverage and 4 module arrays 60 Horizontal coverage remains constant at 90 Adjustable Bridle with quick disconnect pins MPSA Loudspeaker Systems Important Mounting Instructions To ensure proper air movement for the cooling of self powered loudspeakers we recommend a minimum of 2 to 3 feet of clearance in front of the loudspeaker and at least 6 inches of clearance from the sides and the rear cabinet surfaces Warning The actual rigging of loudspeakers suspended from a truss or from a ceiling is a serious undertaking that is beyond the scope of this document It should be done only by qualified and experienced professionals using only load rated hardware We strongly recommend that yo
8. s can also be ground stacked using the subwoofers as a mounting base for the array modules Ground stacks can include as many as 3 array modules plus one or two matching subwoofers Safety considerations are always a factor in any venue and consideration must be given to the strength and stability of the surface platform on which the ground stack will be placed To assemble a ground stack Ground Stack 1 Place the subwoofer that will be used as the base into posi with 2 array modules 1 subwoofer tion 2 Place the next cabinet into position on top of the subwoofer and align the connecting hardware channels 3 If the second cabinet is another subwoofer remove the quick disconnect pins from the top subwoofer and use the knurled knobs to move the joining bars from the top subwoofer down into the lower subwoofer If the second cabinet is an array module remove the upper quick disconnect pins from the sub woofer s joining channels and use the knurled knobs to move the joining bars up from the subwoofer into the array module NOTE The rule on joining bars is that when joining like cabinets two array module modules or two subwoofers move the joining bars from the top cabinet down into the lower cabinet When joining a subwoofer and array module move the subwoofers joining bars into the array module Flying Arrays CF101LA and CFX101LA arrays suspend from a ceiling or truss as easily as they ground stack The subwoofers which were
9. trol settings shown below are provided as guide lines to assist you in setup They are not hard and fast settings that apply to every setup as no two setups are alike Set all controls to 9 dB Set all controls to 6 dB Set all controls to 9 dB Page 9 MPSA Loudspeaker Systems CFX101LA amp CFX15S DSP Settings Suggested DSP settings for various CFX101LA line array modules and CFX15S subwoofer combinations appear below and on the next page Q o C c 2 Q TO e 2 C ac CN i lt vr o wc LL O O c oc MP lt vr ce vr LL O D ZC prar O Q Q O c D 2 o ab N ZC _ C ZC _ O Z PSN SI JeA0SSOJO 9IuoJjo9 e BU19 X 9 ue ueuM ue e g SG X49 U ui JBAOSSOJO eAissed aU ssed q ou od SW Z V1 0LX39 34 Aejap jejoowqns g SS X4O e uy pesn ulaq S v1 01 X32 24 ueuM INON 18yis008 3NON me JNON zH O 9T AON3Rn0394 H31N329 wA 3NON ap OE C imy ioo8 3NON me JNON ZH19 8 ADN3NO3YS YSLNID p GERE 1my iso08 me ADN3ANOSYS YSLNID OR sos 3 AON3Rn0394 H31N32 W3NOSSOUD Oo AlVid O WHaindin VILOLIX3O S2d HOd NIVO dINV JNON qp S JNON OST JNON ZH S I 120 8P ZT 120 8P vz HIYOMYALLNG HILYOMYILLNG d1 2H OCT dH ZH OS VINHON VINHON JNON JNON gp 6 ap 0 gp 9 ap 0 VITOTX4D S2d HOd NIVO dINV qp 0 qD o V
10. u have your design reviewed and approved by a licensed structural engineer who can also verify the suitability of the building attachment points Renkus Heinz is not responsible for any non Renkus Heinz products or for any misuse of Renkus Heinz products EASE FOCUS EASE FOCUS allows you to quickly and accurately determine the size of the array needed to cover the audience and its proper location and aiming angle Page 6 MPSA Loudspeaker Systems CFX101LA AND CF 101LA Connections CFX101LA 8 lngedance i Chena Li 2H W Poe BATTE ANF m pA FUTT 4 b TH Pad t MEEESL X mcr un Tani Fart Caiana A INF IT ai INF UT Screw Terminal Strip Looping In amp Out Inputs Neutrik 4 Pin Speakon Connectors Your CFX101LA loudspeaker was shipped to you wired for fully passive operation using the internal crossover It can be converted to bi amplified operation by removing the connector plate from the cabinet and changing several internal connections For detailed instructions please refer to the Renkus Heinz Loudspeaker User s manual form RH508 Signal amp Limiting LED Status Indicators Screwdriver RENKUS HET Adjustable m Gain Control H ATIENUATIOH PF1 500 Looping In amp Out female in male out XLR Type Connectors 110 V or 230 V 50 60 Hz AC Power On Off Input Voltage Switch Selector IEC Power Connector amp Fuse Page 7 MPSA Loudspeaker Systems CF101LA 5R amp
11. ur down or straight ahead The matching CF CFX15S subwoofers are provided with a threaded pole socket to assure reliability The length of the as sociated POLE CF 101 is easily adjustable To assemble the basic floor system shown here 1 Screw the mounting pole into the threaded pole socket on the subwoofer 2 Place the array cabinet on top of the pole using the bottom mounted tripod socket 3 Adjust the height and coverage angle as desired If a second array module is needed 1 Place the second module on top of the first module and align the metal hardware channels 2 Remove the quick disconnect pins on the top array module and use the knurled knobs on the joining bars to slide them down into the channels on the lower cabinet See Step 2 below 3 Then lock the cabinets together by inserting the quick disconnect pins into the metal channels on the lower cabinet See Step 3 below Floor System single array module and subwoofer If two subwoofers are used follow the same procedure used for the array modules set one on top of the other align remove quick disconnect pins on the top subwoofer slide the joining bars down and lock in place with the quick disconnect pins Pole mounted arrays should be limited to two CF CFX101LA mounted on either one or two subwoof ers Page 3 MPSA Loudspeaker Systems Floor Mounted Systems continued Ground Stacks Point source line array modules and their matching subwoofer
12. used as a mounting base for the ar ray cabinets in ground stacked arrays now becomes the suspen sion platform for the array and are placed at the top of the array Refer to array photo at the top of the next page The Subwoofers are equipped with rubber feet that fit into matching cups in the top of the lower subwoofer when two units are stacked together As a result when the subwoofers are flown CF15S CFX15S Subwoofer in an array such as the one shown above the subwoofer has to turned upside down Otherwise the feet prevent the subwoofer and array module from being joined together Page 4 MPSA Loudspeaker Systems Flying Arrays continued The procedure for assembling arrays that will be flown is similar to the one used to assemble ground stacks except that the order is reversed Ground stacks are assembled from the bottom up while flown arrays are usually assembled from the top down Typically the RHANG101LA Flybar is used to fly an array in both portable applications and permanent installations The cabinets built in attachment points are used mainly in permanent installations To assemble a flown array 1 Attach the RHANG101LA Flybar to the top cabinet using the quick release pins Note the bridle construction which allows you to move the suspension bar laterally and adjust the array s tilt aiming angle Move the bridle toward the rear of the cabinets for more tilt 2 Attach the lifting device chain hoist fork l
Download Pdf Manuals
Related Search