Source Four HID PARNel™ User Guide
Contents
1. pull the housing out 3 Holding it by the base remove the lamp from its box Note To avoid premature lamp failure do not touch the lamp glass with your fingers If you touch the lamp during installation clean it carefully with rubbing alcohol and a clean lint free cloth before operation 4 Insert lamp base into socket assembly Figure 1 5 Push down on the lamp base until the lamp seats firmly 6 Reinstall the lamp housing by aligning the bolt hole and tightening the knurled bolt CAUTION Replace the lamp if it becomes damaged or thermally deformed Improperly installed lamps will cause premature lamp and socket failures Ballast information e The only acceptable voltage is 120V 10 50 60HZ e The standard operating current is 1 5 Amps e The standard inrush current is lt 14 Amps e Room ambient temperature should not exceed 104 F 40 C e The lamp ignition voltage is 4 5Kv non hot restrike e The ballast case temperature should not exceed 167 F 75 C WARNING DO NOT power the Source Four HID PARNel with a dimmable power supply Dimming will damage the ballast and void the warranty am my a h Figure 1 2 Source Four HID PARnel Color frame retaining clip usage E The color frame holder is equipped with a spring loaded retaining clip that prevents _ the locked position color frames and accessories from falling out Make sure the Source Four HID PAR fs Nel has the color frame retaini2. PPH 6 19 X 1 2L 48 2 Plastite PAR zoom wave stippled lens PAR zoom wave clear lens Spring retainer Screw 10 32 X 3 8 PhPH Taptite BO Quantity Required 1 1 1 Source Four HID PARnel 7 Americas m 3030 Laura Lane P O Box 620979 Middleton Wisconsin 53562 0979 USA m Tel 608 831 4116 m 800 688 4116 m Fax 608 836 1736 m 800 555 8912 Europe m Unit 4 Victoria Industrial Estate Victoria Road London W3 6UU UK m Tel 44 0 20 8896 1000 m Fax 44 0 20 8896 2000 Asia m Room 605 606 Tower Ill Enterprise Square 9 Sheung Yuet Road Kowloon Bay Kowloon Hong Kong m Tel 852 2799 1220 m Fax 852 2799 9325 Web www etcconnect com m Email US mail etcconnect com m UK mail etceurope com m Asia mail etcasia com 25 GP otetere Service service etcconnect com m Toll free 800 775 4382 Comments about this document techcomm etcconnect com toe esos avecesececess Copyright 2003 Electronic Theatre Controls Inc All Rights Reserved Product information and specifications subject to change eseesesseseseseseseses 7061M1013 m Rev A m Released 4 03
3. Source Four HID PARNel User Guide source Four HID PARNel guidelines Please note the following precautions prior to use e Do not mount the Source Four HID PARNel on or near combustible surfaces e Do not recess mount the Source Four HID PARNel e The Source Four HID PARNel can be canopy mounted from the ceiling e Always hang the Source Four HID PARNel with the color frame retaining clip in the locked position e The Source Four HID PARNel is NOT dimmable Dimming or regulated voltage will damage the ballast and void the warranty Accessories ETC Part Color frame 7 5 in sq 6 7 in inside diameter 7061A3047 Safety cable 34 in 7061A1022 C elamp o 7060A2009 Top hat 3 PSF1022 Top hat 6 PSF1023 Half hat PSF1027 Cross baffle top hat PSF1031 Egg crate louver PSF1028 Weighted base PSF1032 Gel Extender 3 PSF1030 Gel Extender 6 PSF1029 Barn door PSF1019 Source Four HID PARnel 1 HID Lamp type and general information Do not use lamps other than the following types in the Source Four HID PARNel Use of lamps other than specified below will void UL cUL safety compliance and your war ranty Lamp Type Manufacturing Codes Base Color fe temp CDM T 150W 830 _ 612 T6 56mm 9000 14000 eraic Halide Installing the lamp 1 Disconnect power to the Source Four HID PARNel before installing the lamp 2 Loosen the knurled bolt on the back of the lamp housing and
4. he following steps for reassembly Improper reassembly will result in void of warranty and loss of per formance See parts list on page 7 Tools required Phillips screwdriver 1 Install the reflector mount silicon pads 11 and lens pad 15 in the left barrel 7 or 8 2 With the wave side of the lens facing toward the front of the fixture install the wave clear lens 21 into the rear lens track 3 Assembly items 16 17 18 and 19 Focus knob assembly Rotate the focus knob full spot position The arrow on the focus knob will point approximately to the 11 O clock position Place the focus knob assembly into the left barrel Install the lens stop 14 and the rotator spring clip 12 into the lens rotator 12 or 13 Install the lens rotator into the left barrel Install the rotator pressure clip 9 into the left barrel with screw 23 Install the gel retainer clip 1 and the spring 22 into the right barrel 5 or 6 Attach the right barrel to the left barrel using screws 3 in three places O ON OO oO fF 10 Check that the gel clip retainer 1 moves easily into position 11 Check for smooth rotation of the lens rotator 12 or 13 12 With the wave side facing inward install the wave stippled lens 20 into the lens rotator Source Four HID PARnel 5 Spare parts list Source Four HID PARNel Final Assembly Reference Part Number Description Quantity Number Required 4 7061A2022 S4 HID PAR ba
5. m the fixture Place the fixture on a flat stable work surface Do not install or remove lenses with the unit hanging Rotate the focus knob to full spot position Tilt the front of the fixture down at least 45 degrees Press the spring clip with your finger to release the lens Figure 3 w Allow the lens to drop forward from under the clip When the lens drops remove your finger allowing the lens to slide forward until it rests on the lens catchers Figure 4 oO N OCO A 9 Carefully remove the lens from the fixture Installing a wave stippled lens front 1 Position the fixture with the front of the unit the lens side facing you and tilted slightly Figure 3 2 Rotate the focus knob to full spot position 3 Hold the lens by the edge and position it so the wave side faces the back of the fixture Figure 5 4 From the top of the fixture slide the lens behind the lens catchers and position its base behind the tabs on the bottom of the lens rotation ring See Positioning the wave stippled lens below 5 Gently push the top of the lens inward until it snaps behind the spring clip Positioning the wave stippled lens front e There are seven notches cut into the stippled side of the lens Position the lens so that the cluster of three notches is on top The center notch of the cluster coincides with the spring clip on the lens retaining ring Figure 6 e The bottom of the lens has a cluster
6. ng clip in the locked position when hanging Figure 2 We at Note Make sure to use colorframes or accessories with a 6 7 inch inside diameter 1 Release the retaining clip by pushing it sideways The retaining clip opens 2 Insert the color frame 3 Press the retaining clip down until it locks Figure 2 Focus Knob Positioning rt on f P d 45 field angle k Taa Focus knob in flood position 25 field angle l Focus knob screw Focus knob in spot position To adjust the Focus knob tension loosen or tighten the Focus knob screw to exceed rotational limit Overtightening may result in f CAUTION The focus knob does not rotate 360 Do not attempt damage or breakage of the knob Lens identification The Source Four PARNel comes equipped with two types of lenses Wave Stippled WS and Wave Clear WC The type can be identified by the lens texture The WC rear lens is in a fixed position inside the fixture The WS lens is in the rotating ring at the front of the fixture The wave surfaces face each other Wave Stippled lens Wave Clear lens Source Four HID PARnel 3 A Changing Source Four PARNel lenses Change lenses if they become cracked or badly scratched CAUTION place Removing a wave stippled front lens 1 Source Four PARNel lenses get hot while the unit is in operation Let the fixture cool before handling the lens 2 Disconnect power fro
7. of four notches Place the two center notches behind the tabs at the bottom of the lens rotating ring Figure 5 Never operate the Source Four PARNel without a lens in Spring clip D R Focus Knob Retaining clip Figure 3 Lens catcher Figure 4 Retaining clip Spring clip Tab Figure 5 l Top center notch Bottom two center notches Figure 6 4 Source Four HID PARnel Cleaning the reflector Unplug the fixture before attempting to clean the reflector Remove the lamp before attempting to clean the reflector Remove the lenses so you can access the reflector from the front of the fixture hwWhDd Remove dust with a blast of oil free air or wipe with a clean soft lint free cotton cloth If this is sufficient to remove dust go to step 7 Otherwise continue to step 5 5 Dampen a clean soft lint free cotton cloth with a mild soapy water solution and gently wipe the reflector 6 Remove any soapy water residue with a clean soft lint free cotton cloth dampened with water 7 Reinstall the lenses before using the fixture CAUTION Do not use glass or window cleaners on the reflector Chemicals in the cleaners will harm the reflective coating Do not use paper towels or harsh materials to wipe the reflector These materials can scratch the surface of the reflector Housing assembly instructions If you take apart the Source Four HID PARNel for any reason please use t
8. se 4 assembly black 2 7061A2022 1 SAMPAR DARE 1 assembly white 120V HID PAR Lamp 2 TOG TAAAAROR socket assembly black l 4 7061A2024 1X UN ETAR E 1 socket assembly white 5 7061A3039 HID PAR yoke bracket 1 black 6 7061A3039 1 HID PAR yoke bracket 4 white T HW5125 Bolt carriage 1 8 HW5126 Washer flat 1 9 HW5139 Washer split ring lock 2 10 HW5172 Bolt hex 2 11 HW5270 Bolt spinlock 2 12 HW522 Washer flat 2 43 HW8144 Handle yoke knob 4 black 14 HW8144 1 Handle yoke knob 4 white 6 Source Four HID PARnel Spare parts list Source Four HID PARNel Housing Assembly Reference Number 1 oO oOo N O oO A OO N N N N N o A A A A A M Oo N gt O O N QO o FPF O N gt O Part Number 7061A3005 7061A3013 7061A3014 7061A3014 1 7061A3025 7061A3025 1 70612019 70612019 70613029 HW492 7061A4001 70614012 70614012 1 7061A4029 7061A4020 7061A4013 7061A4014 7061A4015 HW2154 7061A4010 2 7061A4010 1 HW750 HW4145 Description Gel retainer clip Spring clip rotator Reflector painted black Reflector painted white Barrel painted black Barrel painted white Source Four PAR rivet assembly black Source Four PAR rivet assembly white Rotator pressure clip Screw 10 32 X 5 8 PhPH Taptite Pad silicon reflector mount Lens rotator black Lens rotator white Lens stop PARNel lens pad Focus knob bushing Focus knob gear Focus knob Screw
Download Pdf Manuals
Related Search