Home

2 burner gas grill assembly and operating instructions

1. Step 10 Assemble the harmonic balancer Part 22 to the timing chain cover Part 12 use screw M6 x 10 x 1 pc tighten the screw 10 Step 11 Assemble the main body handle assembly Part 18 with main body handle heat insulation Part 31 x 2 pcs to the right side of main body assembly Use screw M10 x 16 x 4 pcs tighten the screws CAUTION The SLOT ON THE MAIN BODY HANDLE MUST FACE DOWN Step 12 Assemble the lid handle assembly Part 17 with lid handle heat insulation Part 30 use screw M10 x 16 x 3 pcs tighten the screws Step 13 Assemble the water neck Part 24 to the lid use screw M10 x 18 x 2 pcs tighten the screws 11 Step 14 Assemble the distributor cap Part 19 to the distributor use screw M6 x 12 x 2 pcs and nuts M6 x 2 pcs tighten the screws Step 15 Put one end with step of the air cleaner fixing bolt Part 27 into the lid use nut M4 x 1 pc tighten the nut Step 16 Assemble the carb plate Part 20 to the lid use screws M8 x 23 x 4 pcs tighten the screws see picture 12 Step 17 Put the carb spacer Part 23 inside the carb plate Step 18 Assemble the air cleaner assembly Part 13 to the air cleaner fixing bolt Part 27 and put it on the top of carb spacer Part 23 then use air cleaner dome nut Part 25 to tight it 13 Step 19 Assemble the zoomies assembly REAR Pa
2. NOT be attempted as it will create an unsafe situation When changing the gas cylinder it shall be carried out away from any source of ignition The gas must be turned off at the cylinder when the outdoor gas grill is not in use Do not store this gas grill indoors unless cylinder is disconnected and removed from the appliance Cylinders must always be stored outdoors out of the reach of children and must not be stored in a building garage or any other enclosed area WARNING a Do not store a spare gas cylinder under or near this appliance b Never fill the cylinder beyond 80 percent full c If the information in b12 a and b12 b is not follow exactly a fire causing death or serious injury may occur O Never use this gas grill without the collection tray and drip cup in place WARNING If you see grease or other hot material dripping from the grill onto valve hose or regulator turn off gas supply immediately After the grill has cooled determine the source and correct it Check the gas grill for gas leaks and burner obstructions before each use WARNING Do not use a flame to check for gas leaks See Leak Test Instruction section of this manual for correct leak test procedures A clogged burner tube can cause a fire inside or beneath the grill DANGER If you see smell or hear escaping gas from the gas cylinder evacuate the area and call the fire department WARNING Never light the gas grill before l
3. cleaned of food debris after each cooking session If the grill is to be used for large gatherings it will be necessary to turn off and cool the grill every two hours to remove food debris from the drip tray and clean the drip tray The time between cleaning may need to be reduced if very fatty foods or low quality meat products are being cooked Failure to do this may result in a fat fire which may cause injury and could seriously damage the grill 23 In theevent ofa fat fire 0 Ifsafetodoso turn all control knobs to the off position O Turn off the gas at the cylinder Keep everyone at a safe distance from the grill and wait until the fire has extinguished Do not close the hood of the grill NEVER DOUSEA GRILL WITH WATER IF AN EXTINGUISHER IS USED IT SHOULD BEA POWDER TYPE 0 DO NOT REMOVE THE DRIP TRAY If the fire worsens contact your local Fire Department for assistance CARE AND MAINTENANCE Never handle hot parts of the grill with unprotected hands Never douse the grill with water when its surfaces are hot Keep the ventilation openings of the cylinder enclosure free and clear from debris General 0 Regularly clean your grill between uses and especially after extended periods of storage Do not leave the grill uncovered and exposed to the elements when not in use Even when stored outside or inside with a cover it 1s possible for mold to grow on any fat remaining on parts of the grill This should be cleane
4. color this could be a result of a blocked burner from grease drippings or from insects building a nest inside the burner of burner opening Clean the port hole of the burner using a pipe cleaner or other similar shaped instrument When storing the appliance for long periods of time wrap the burners in aluminum foil to prevent nsects from blocking the burner ports Observe Flame Height When lit Flame should be a Blue Yellow color SS between 1 2 when burner is on HIGH K ESSENTIAL INFORMATION Please read all instructions before using your grill BEFORE YOU USE YOUR GRILL also see installation 6 Perform a leak test before each use This is the only safe and sure way to detect any gas leaking from joints and connections of the grill after assembly Follow the LEAK TEST INSTRUCTIONS Check that the gas hose to ensure it 1s free of any tension twisting cuts or cracks Make sure your grill is in a safe place It must be outdoors on level ground and not below ground level Ensure that the grill is least 36 inches 91cm away from any flammable materials including trees and fences and that there are no heat sources near the grill cigarettes open flames spark etc 0 Check that you have the correct gas cylinder and regulator for your grill Check and clean burner venture tubes for insects and insect nests A clogged tube can lead to a fire beneath the grill GETTING STARTED also see operation O Main Bu
5. cylinder and wait for the fire to go out Do not pull out the drip tray or douse with water Never douse a grill with water Never move a grill when lit Never leave a lit grill unattended Never handle hot parts with unprotected hands Keep children animals and elderly people a safe distance from a lit grill WHEN YOU HAVE FINISHED COOKING also see care and maintenance Turn all the main burners to the high position for 3 to 5 minutes to burn off any food residue from the cooking surfaces and burners When the grill has cooled the burnt residue can be easily removed using a damp non abrasive cloth on the cooking surfaces and a wire brush on the burners Never use any abrasive material on stainless steel finishes The cooking grids are not dishwasher safe When the grill has cooled scrape away any food and fat residues form the drip tray and discard This routine must be completed after each session 21 0 Clean grill with a solution of mild detergent and water After cleaning make sure the grill is rinsed thoroughly For stubborn residue on the cooking grates use a soft bristle brush DO NOT USE A BRUSH ON THE STAINLESS STEEL EXTERIOR 0 After cleaning Cooking Grids it is recommended that you apply a light coat of cooking or vegetable oil to help protect grids Never use aerosol chemical or abrasive cleaners on any grill surfaces STORAGE O Ensure the grill is properly cooled Storage of this gas grill
6. griddle Full coverage of plates will cause excessive heat and could damage the grill Any alteration to the design of the grill will void any and all warranties and may result in an unsafe condition Illustrated parts list 1 Main Body Assembly 2 Cooking Grill lpc 3 Flame Tamer 2pcs 4 Control Knobs 2pcs ar 7 Oil Cup Bracket lpc 8 Oil Cup 1pe 9 Trolley Stand Assembly 10 Trolley Tube Assembly 11 Trolley Tube Assembly lpc right lpc left lpc 13 Air Cleaner 14 Zoomies Assembly 15 Zoomies Assembly 17 Lid Handle Assembly lpc front lpc rear lpc Assembly lpc 18 Main Body Handle 19 Distributor Cap ss PC pe 23 Water Neck lpc 24 Air Cleaner Dome 25 Flame Tamer Nut 1 pce Support Assembly and Spark Plug Boots Assembly 28 Match holder 29 Lid Handle Heat 30 Main Body Handle 32 Trolley Wire Basket assembly lpcs Insulation lpc Heat Insulation Support 2pcs 33 Trolley Wire Basket lpc Hardware Pack Bolt M3x8mm i Bolt M6x7mm Bolt M6x10mm Bolt M8x14mm saa Bolt M8x23mm N Bolt M6x12mm M Bolt M10x65mm N Bolt M10x20mm z ejrj e e ee MV 2PCS APCS 7PCS 8PCS APCS 24PCS 7PCS 2PCS 2PCS 2PCS il ej v e o z ze IPC Nut M10 Wheel Axle Bolts m Pin clip Spacer Washers AA Battery Allen key 5mm Allen key 8mm 8PCS 2PCS 2PC
7. sure it can be hanged Step 27 Assemble Hose Clip Part 37 to trolley stand assembly Part 9 use screw M6 x 10 x 2 pcs tighten screws Step 28 Open tank valve fully counterclockwise Use a soapy water solution to check all connections for leaks before attempting to light your grill If a leak 1s found turn tank valve off and do not use your erill until the leak is repaired Fully Assembled SS aii nuit ili aii REREN ais T i mr AINU N SONEA NAN Ii U an vad AL A r L LAAR ti i ee pI V Hit 5 p 18 BURNER WITH RESPECT TO PROPER LOCATION WARNING ALWAYS CHECK TO ENSURE BURNERS ARE POSITIONED CORRECTLY BEFORE EACH USE THE ORIFICE MUST BE IN INSIDE OF THE BURNER cs 7 THROUGH THE VIEWING HOLD PLEASE SEE PICTURE CONNECTING THE GAS Connecting to a Gas Cylinder 1 Ensure all control knobs are in the OFF position and verify that the gas cylinder valve 1s closed by turning the handle on the gas cylinder valve clockwise until it stops 2 Remove the protective cap from the gas cylinder valve nozzle 3 Hold regulator in a straight line with gas cylinder valve nozzle so the connection does not cross thread 4 Insert regulator nipple into the gas cylinder valve nozzle opening 5 Hand tighten coupling nut in a clockwise direction Do not use tools 6 Perform a Leak Test See Leak Testing section of this manual Discon
8. MODEL HRG350 2 BURNER GAS GRILL ASSEMBLY AND OPERATING INSTRUCTIONS A DANGER A WARNING If you smell gas 1 Do not store or use gasoline or other 1 Shut off gas to the appliance flammable vapors or liquids in the vicinity 2 Extinguish any open flame of this or any other appliance 3 Open hood 2 An gas cylinder not connected for use shall 4 If odor continues keep away from the not be stored in the vicinity of this or any appliance and immediately call your gas other appliance supplier or your fire department For outdoor use only Not for commercial use Read instructions before using the appliance Failure to follow instructions could result in death serious bodily injury and or property loss Warning accessible parts may be very hot Keep young children away OG Do not move the appliance during use WARNING um off the gas supply at the gas cylinder after use Any modification of the appliance may be dangerous Installer to leave instructions with the consumer and consumer to retain them for future reference CONTACT 800 794 4826 SERVICE LINE FOR ASSISTANCE 0 DO NOT RETURN TO PLACE OF PURCHASE WARNINGS PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY AND USE FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN DEATH SERIOUS BODILY INJURY AND OR PROPERTY LOSS READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY OR USE OF THIS OUTDOOR GAS GRILL WARNING Read and follo
9. S 2PCS 2PCS 4PCS N Hes rij p Dr IPC IPC IPC ASSEMBLY INSTRUCTIONS Estimated time for assembly will be 45 mins Before You Start 0 When you are ready to start make sure that you have the right tools at hand plenty of space and a clean dry area for assembly Assembly Note Two People Reguired for Assembly O Using knife or box cutter cut open carton 0 Lay out all screws and check lengths before assembly It is recommended that the carton is cut open and spread out on the floor and used as a protective surface during assembly Refer to the assembly diagrams as necessary Remove all packaged parts from the inside of the grill body before assembling This product is for OUTDOOR USE ONLY NEVER use indoor in an enclosed area or below ground level NEVER use an adjustable regulator with this grill Use only the pressure regulator and hose supplied Assemble on a level floor or ground Preparation Unpack and inspect all parts listed If you believe you have missing parts please check all boxes parts of the grill Some parts are shipped in place or pre assembled If you have damaged or missing parts DO NOT RETURN TO THE STORE Please visit us on the web at www hotrodgrills com Step 1 See picture assemble castor Part 5 with trolley tube assembly RIGHT Part 10 use bolts M8 x 14 x 4 pcs and nuts M8 x 4 pcs tighten the bolts Do the same way to fix the other castor Step 2 Step 2 Assemble
10. d off smooth surfaces with hot soapy water 6 All screws should be checked and tightened if necessary on a regular basis Keep the outdoor gas grill area clear and free from combustible materials gasoline and other flammable vapors or liquids Make sure there 1s no obstruction surrounding the grill which may block the flow of combustion and ventilation air 8 8kW 642 g h Butane Propane LPG gas mixtures 28 30 mbar 37mbar 28 30 mbar 37mbar 1 04 mm 1 04 mm 0 87mm 0 98 mm Pin Code No 598 CL247 Gas cylinder Standard gas cylinder certified regulator according to EN 12864 Regulator flow ate ee 1 5kg h certified gas hose according to applicable EN standard max 1 5m max FI 1 2m This appliance has been made with regard to European Gas Standard EN498 and bears the CE certification No CE0598 24 TROUBLE SHOOTING 1 Make sure gas cylinder is connected and its valve is in the open position 2 Make sure gas cylinder has fuel My grill will not light 3 There may be debris in or around the burners The grill should be cleaned after each use 4 Follow the lighting procedures in the Getting Started section of the manual The gas cylinder must be turned on BEFORE opening burner valves 5 Perform leak test 1 Flare ups are usually caused by food or grease The grill should be cleaned after each use to reduce flare ups The flames on my grill are too high or intense 1 Make sure the battery is install
11. ed properly The igniter does not work 2 Battery could be dead replace with The igniter does not work a new battery 1 Make sure the grill 1s not exposed to winds over 4m s 2 Check the level of the gas Very low levels of fuel may cause burners to go out 3 Perform leak test The flame goes out when the burnersare turned too low DO NOT RETURN TO PLACE OF PURCHASE PLEASE CONTACT 800 794 4826 CUSTOMER SERVICE FOR ASSISTANCE HOT ROD GRILLS LLC LAKE HAVASU CITY AZ USA WWW HOTRODGRILLS COM 8 00am 4 00pm MST 25
12. her assistance O Do not store a spare LP gas cylinder under or near this appliance Never fill the cylinder beyond 80 percent full If these instructions are not followed exactly a fire causing death or serious injury may OCCUT Hose Inspect the hose before each use Only use hose supplied from the manufacturer Ensure that flexible hose is not subjected to twisting after connection t is necessary to change the flexible hose when the national conditions require it You must have the correct gas cylinder regulator and hose assembly for grill to operate safely and efficiently Use of an incorrect gas cylinder regulator or hose assembly is dangerous and will invalidate the warranty on this product If you are unsure please contact our customer Service 22 LOCATION Precautions 0 Only use this grill in a well ventilated outdoor area Check that the grill is not placed UNDER any combustible surface The side of the grill should never be closer than 91cm 36 inches to any combustible material Do not obstruct any ventilation openings in the grill body Confirm all control knobs are in the off position before connecting the regulator to gas cylinder The casters should always be in the locked position when the grill is in use OPERATION Your grill is not designed to be used with more than 75 of the cooking area as a solid plate this includes baking dishes If your cooking area is more than 75 covered by a so
13. ifting the lid to prevent an explosion from gas build up Exercise care when using this gas cooking appliance Never leave gas grill unattended during operation or cleaning Never allow children to operate or play near this or any gas grill WARNING Do not move a gas grill when in operation or hot WARNING Never touch hot surfaces Use heat resistant gloves The gas grill will become very hot Use of this gas grill other than for the intended use or alteration of gas grill in any way may not be safe and could result in death serious bodily injury and or property loss Never attempt to repair the gas grill or gas cylinder yourself Contact the manufacturer for information regarding repairs to your gas grill Contact your local gas supplier for information regarding repairs to you gas cylinder WARNING Do not use aerosols or store flammable liquids or materials near this gas grill WARNING Do not wear loose clothing around any gas grill while in use or hot Never store an gas cylinder indoors empty or filled If storing the gas grill indoors disconnect the gas cylinder and store it outdoors out of the reach of children Never leave an gas cylinder inside a vehicle which may become overheated by the sun Do not attempt to disconnect any gas fitting while your gas grill is in operation Your gas grill should be cleaned regularly This gas grill should never be used with more than 50 of the cooking area as a solid plate
14. indoors is permissible only if the gas cylinder is disconnected and removed from the grill Store the grill in a cool dry place Always disconnect the gas cylinder and store it in a safe place never store a gas cylinder on its side Never store a gas cylinder in a building garage or any other enclosed area If you intend to leave your grill outside make sure it is protected from the elements by a heavy duty cover not included 0 Keep outdoor cooking gas grill area clear and free form combustible materials gasoline and other flammable vapors and liquids IMPORTANT INFORMATION This product is for outdoor use only Do not use indoors Do not use below ground level Do not store gas cylinders below ground level LPG gas is heavier than air so if a leak occurs the gas will collect at a low level and could ignite in the presence of a flame or spark 0 Do not store or use gas cylinders on their side as this could allow liquid gas into the supply pipes with serious results Leak test your grill before each use Leak test the hose connections each time you reconnect the gas cylinder Always turn off the gas at the cylinder when not in use O Cylinders must always be stored outdoors out of the reach of children and must not be stored in a building garage or any other enclosed area Only use the pressure regulator and hose assembly supplied with this grill If replacements are needed please contact 800 794 4826 for furt
15. lid cooking surface the grill could overheat causing damage that is not covered by the warranty Roasting hooded grills only A roasting hood allows you to roast or bake in a similar way as in a conventional gas oven For best results place the food you wish the bake or roast in a metal baking tray and set it on one side of the cooking grill Turn the burners directly under the food to the OFF position and the burners opposite the food the Medium setting Close the lid and this will form an oven to cook the food indirectly Monitor the temperature using the temperature gauge on the lid If the internal heat becomes too high turn the burners to the low position It is not necessary or advisable to have all of the burners on high when the hood is closed If the hood is opened during cooking to check on the progress of the food please allow extra cooking time for the grill to regain its temperature Take care when opening the hood as hot steam can be released upon opening Flare up control Flare ups will often occur when food 1s grilled as fat and juices fall onto flame diffuser Some fat 1s necessary to give the food its barbecued flavor but excessive fat can result in a flare up To avoid flareups trim excess fat from meat and poultry before grilling use cooking sauces and marinades sparingly and try to avoid low quality cuts of meat or meat products that are high in fat and water contents Fat Fires The drip tray must be emptied and
16. necting the Gas Cylinder 1 Turn all control knobs to the OFF position and turn the handle on the gas cylinder clock wise until it stops 2 Turn coupling nut on regulator in a counter clockwise direction until regulator is released from threaded gas cylinder valve nozzle 3 Place the protective cap over gas cylinder gas nozzle LEAK TESTING Always perform a leak test in a well ventilated area Step 1 Confirm all control knobs are in the off position Step 2 Turn on the gas at the gas cylinder Step 3 Check for leaks by brushing a solution of 1 2 water and 1 2 liquid detergent over all the gas system joints including valve connections hose connections and regulator connections Step 4 If bubbles form over any of the joints there is a leak OG Turn off the gas O Retighten all joints Repeat test If bubbles form again do not use the grill and contact your gas supplier or fire department for assistance LIGHTING THE GRILL 1 Open lid during lighting 2 To ignite a burner push and turn the burner control knob to high 3 Press the electronic igniter amp hold for 3 5 seconds to light the burner 4 If ignition does not occur in 5 seconds turn the burner control s off wait 5 minutes and repeat the lighting procedure If the burners can not be lit using the ignition system turn to the manual lighting instructions under important information 5 Follow same steps to light front and rear burner 6 Once the burne
17. rner Open the hood of your grill Never light your grill with the hood closed Turn the gas cylinder valve to the ON position Push the center control knobs in on the burner you wish to light and turn it to the high position Fully depress the igniter button for 4 to 5 seconds to light the burner Light all other burners form left to right making sure each burner 1s lit before lighting the next IF ANY BURNER FAILS TO LIGHT TURN OFF THE GAS AT BURNERS AND THE CYLINDER WAIT 5 MINUTES AND TRY AGAIN If the burners cannot be lit using the ignition system turn to the manual lighting instructions under important information Once the burners are lit turn all the main burners to the high setting for 3 5 minutes to pre heat the grill This should be done before each session Pre heat grill with hood of the grill closed When pre heating is complete cooking can begin taking extra care if the burners are used in the high position When cooking for the first time cure the Cooking Grids by applying cooking or vegetable oil to the Cooking Grids After lighting the grill let the Cooking Grids cure for 30 minutes under low heat The Cooking Grids should now be seasoned and ready for use 6 To prevent food from sticking we recommend that you use a long handled brush to apply a light coat of cooking oil to the cooking grids before each grilling session Ifa fat fire should occur during cooking and if safe to do so turn off the burners and the gas at the
18. rs are l t turn all the main burners to the HIGH setting for 3 5 minutes to pre heat the grill This should be done before each session When pre heating 1s complete cooking can begin 7 To prevent food sticking we recommend that you use a long handled brush to apply a light coat of cooking oil to the cooking grids before each grilling session OFF OFF OFF i HRG nig a ss LOW LOW OFF High Low MANUAL LIGHTING INSTRUCTIONS 1 To light with match insert long stick match in Match Holder of the Match Lighting Chain attached on the timing chain cover Open the lid Light match and place through the Cooking Grill until the lit end 1s alongside anyone of two burners Push and turn control knob counterclockwise to the high position taking care to protect yourself from flames 2 When the burner is lit do the same way to the other burner Confirm that each burner 1s lit before lighting the next burner 4 If the burner fails to light turn off the gas and contact our customer service for assistance 8 00am to 4 00pm MST UJ CHECKING THE FLAME Your burners have been preset for optimal flame performance A blue flame possibly with a small yell ow tip 1s the result of the optimal air and gas mixture The flame should be checked before the initial cooking session and periodically throughout the grilling season especially after storing the grill over a long period of time If the flame 1s significantly yellow in
19. rt 15 to the lid use screw M6 x 12 x 6 pcs and nuts M6 x 6 pcs tighten the screws Do the same way to fix zoomies assembly FRONT Part 14 See illustration Step 20 Put the Spark plug wires and spark plug boots assembly Part 28 into distributor cap Part 19 and main body The longer set is for rear the shorter set is for front CAUTION THE BLACK SPARK PLUG WIRE HOLDERS CANNOT BE CONNECTED TO ANY METAL PARTS 14 Step 21 Put the control knobs Part 4 to bottom on the valve of the control panel tighten the screws on the knobs Step 22 Un screw the igniter cover insert AA battery and replace the igniter cover Note The negative pole of the battery should be inserted first Step 23 Put the two flame tamers Part 3 over two burners 15 Step 24 Put the cooking grill Part 2 onto inside of main body a M LT 5 Eva s Iw Step 25 Assemble the trolley wire basket support Part 34 to the trolley wire basket Part 35 use screw M3 x 8 x 2 pcs tighten the screws Then insert the trolley wire basket support into the hole of the trolley tube assembly RIGHT Part 10 and fix the trolley wire basket holder sheet Part 36 on the trolley stand assembly Part 9 Use screw M6 x 10 x 2 pcs tighten screws 16 Step 26 Put the oil cup Part 8 into the oil cup bracket Part 7 first then put two ends of the oil cup bracket into two holes of oil pan Part 16 and make
20. the trolley stand assembly Part 9 with trolley tube assembly LEF T Part 11 use bolts M10 x 65 x 2 pcs space washer x 2 pcs and nuts M10 x 2 pcs tighten the bolts Step 3 Insert the STEP 1 part to STEP 3 part use pin x 1 pc and pin clip x 1 pc then use bolt M10 x 20 x 1 pc tighten the bolt Step 4 Assemble two wheels Part 6 to both sides of trolley tube assembly LEFT use wheel axle bolts x 2 pcs and spacer washer x 2 pcs tighten the bolts Step 5 Cover the wheel cover Part 32 to the wheel Step 6 Put the main body assembly Part 1 into the finished trolley as picture shown Use pin x 1 pc and pin clip x 1 pe then use bolt M10 x 20 x 1 pc tighten the bolt CAUTION KEEP THE MAIN BODY IN A HORIZON WAY Step 7 Assemble the flame tamer support assembly Part 26 use screw M6 x 10 x 2 pcs tighten the screws Step 8 Assemble the oil pan assembly Part 16 use screw M6 x 7 x 4 pcs fixed underneath the main body assembly tighten the screws Step 9 Assemble the timing chain cover Part 12 to the right side of main body assembly use screw M6 x 12 x 10 pcs and nuts M6 x 10 pcs tighten the screws Meanwhile using the screw showed on the picture to fix match holder assembly Part 29 to timing chain cover Part 12 Note Put screw through the hole of match holder Part 29 see picture then put it through the hole on timing chain cover Part 12 and tighten it
21. w all instructions Retain these instructions for future reference This outdoor gas grill is for use only outdoors DO NOT use inside a building garage or any other enclosed area This outdoor gas grill is not intended to be installed in or on recreational vehicles and or boats 6 This outdoor gas grill should not be located under overhead combustible construction and proper clearances must be maintained at all times from combustible construction and or materials with MINIMUM clearances as follows From Sides 91 cm 36 in From back 91 cm 36 1n Place in a well ventilated area O Inspect the hose before each use Open the door of the frame to inspect the hose before each use If there 1s evidence of excessive abrasion or wear or the hose is cut it must be replaced prior to the outdoor cooking gas appliance being put into operation The replacement hose assembly shall be that specified by the manufacturer 6 WARNING If your outdoor gas grill catches on fire use an ABC fire extinguisher to extinguish the fire Never attempt to extinguish a grease fire with water or other liquids Turn off all control knobs on outdoor gas grill and gas cylinder valve if they can be reached safely If you cannot safely reach the control knobs or gas cylinder valve to stop the flow of gas that can feed the fire evacuate the area and call the fire department This gas grill is not designed to be used with natural gas Conversion to natural gas should

2 burner gas grill assembly and operating instructions

Contents

Download Pdf Manuals

Related Search

Related Contents