USER MANUAL
Contents
1. OBLAMATIK USER MANUAL SMARTLEVEL for washbasin in public and bi stable solenoid valve Ow Disclaimer This manual was created with great care Oblamatik AG shall not be liable for technical or typographical errors and reserves the right to make changes to the product and or the instructions at any time without notice Oblamatik is not liable or responsible for direct or indirect damages which is in connection with the installation or operation of this product Imprint This manual is a publication of Oblamatik AG Gaeuggelistrasse 7 CH 7000 Chur SWITZERLAND All rights including translation are reserved Reproduction by any method for example photocopies or electronic recording are not allowed Reproduction in full or partly is prohibited These instructions represent the technical status at time of printing 6 The user manual must be given to the user Please read this user manual carefully before using the system and keep in a safe place for future reference To reduce the risk of injuries scalding and electrical shock the safety precautions below must be instal led and followed Risk of injury This device is not intended for use by persons with different or reduced physical sensory or mental abi lities or who lack experience or knowledge unless they are under the supervision of or receive training for the use of the device by a person responsible for their safety CONTINUOUSLY TURNING2. 222709 03 15
3. THE CONTROL WHEEL IN THE CLOCKWISE DIRECTION MAY OVERRIDE THE PRE SET MAXIMUM TEMPERATURE RESULTING IN A RISK OF SCALDING If the power cord gets damaged it must be replaced by the manufacturer its authorized service agent or qualified personnel to avoid danger Never operate the device with a damaged cable or plug Do not pull on the power cable as this could cause damage to the cable and cause electric shock Malfunctions Possible cause Solution The device is not working Start Diagnostic Check that The control unit is connected to the mains There is no power supply failure The electric plug inside the control unit is well connected No water flow when activated Check that Your faucet is connected to the water supply Both angle valves are fully opened Check another faucet in the house if water is running The water supply hoses are not bent or twisted The supply hoses might be soiled The control unit is connected to the mains Minimal water flow Check that Both angle valves are fully opened The water supply hoses are not bent or twisted The supply hoses might be soiled Continuous water flow Press the ON OFF button Close angle valve or main valve After a few minutes open again It s still a continuous water flow close valve and contact your installer Use soft cloth soapy solution and water for regular care Wipe with a dry cloth Avoid the use of abrasives or solvents which damage t
4. he surface Damage caused by inappropriate treatment by the user is not covered by our guarantee Color setting of the LED color ring Press amp hold for 2 sec until LED color ring is flashing RED Release knob immediately Press 2x briefly until LED color ring is flashing GREEN Release knob immediately BLUE 1 min Press amp hold for 2 sec choose desired color Changing between the colors WHITE close ee Press 1x briefl for washbasin application for public ress riefly and bi stable solenoid valve Hygienic flushing Saving the settings Press hold for 2 sec until LED color ring is flashing RED Release knob immediately Press amp hold for 2 sec until LED color ring is flashing 2x in the selected color Press 1x briefly until LED color ring is flashing YELLOW Release knob immediately The following settings are active Available Colors for 5 min after initiation Maximal water flow time Press amp hold for 2 sec until LED color ring is flashing RED Release knob immediately Basic functions via menu button Press amp hold for 2 sec and adjust desired interval flushing Water ON BLUE Press 1x water ON Changing between the interval flushing Press 1 x briefly Water OFF cer dies for 2 sec and adjust desired Eero BLACK inactive Press 1x water OFF 3 i 9 Changing between the water flow time Press amp hold for 2 sec until LED color ring is wu Activat
5. ing the cleaning mode flashing 2x in the selected color Is operating with a connected bi stable solenoid valve Press 1x briefly Deactivate Interface Flashing color Interval disabling of water flow for 45 sec Saving the settings Press amp hold until LED color ring is 1 day 10 sec flashing GREEN Release knob immediately NK flashing 2x in the selected color 2 days 10 sec 3 days 10 sec Reactivate Interface Flashing color Water flow time WHITE close Press amp hold until LED color ring GREEN goes out or wait 45 sec automatic reactivation 950 2 095 Z 104 pyoy 2 950 2 de de de de de de de e u ew de VY 995 Z 10 lt piou sg yno CAREAT 950 2 de 29s OL sAepe de de de 29s OL 5 Z de 395 10 moyen lt 850 9 gaaes lt lt das OL de NV 995 Z 10 YIN 950 2 de de de de lt bunjas nosuwun de 995 Z 10 995 104 dn samod Jaye 5 1 0 15 11 Ul dnyas 995 Gy 995 Z 104 pjoy 9 Yono yNoaul 9 99 95 de 995 Z 10 da p104 49Nn0 uiuealg 95 pow bulueal2 Oblamatik AG G uggelistrasse 7 CH 7000 Chur 41 81 286 70 00 info oblamatik ch oblamatik ch
Download Pdf Manuals
Related Search